* pci/host-vmd:
x86/PCI: Add driver for Intel Volume Management Device (VMD)
PCI/AER: Use 32 bit PCI domain numbers
x86/PCI: Allow DMA ops specific to a PCI domain
irqdomain: Export irq_domain_set_info() for module use
genirq/MSI: Relax msi_domain_alloc() to support parentless MSI irqdomains
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
The Intel Volume Management Device (VMD) is a PCIe endpoint that acts as a
host bridge to another PCI domain. When devices below the VMD perform DMA,
the VMD replaces their DMA source IDs with its own source ID. Therefore,
those devices require special DMA ops.
Add interfaces to allow the VMD driver to set up dma_ops for the devices
below it.
[bhelgaas: remove "extern", add "static", changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pull x86 fixes from Ingo Molnar:
"Misc changes:
- fix lguest bug
- fix /proc/meminfo output on certain configs
- fix pvclock bug
- fix reboot on certain iMacs by adding new reboot quirk
- fix bootup crash
- fix FPU boot line option parsing
- add more x86 self-tests
- small cleanups, documentation improvements, etc"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu/amd: Remove an unneeded condition in srat_detect_node()
x86/vdso/pvclock: Protect STABLE check with the seqcount
x86/mm: Improve switch_mm() barrier comments
selftests/x86: Test __kernel_sigreturn and __kernel_rt_sigreturn
x86/reboot/quirks: Add iMac10,1 to pci_reboot_dmi_table[]
lguest: Map switcher text R/O
x86/boot: Hide local labels in verify_cpu()
x86/fpu: Disable AVX when eagerfpu is off
x86/fpu: Disable MPX when eagerfpu is off
x86/fpu: Disable XGETBV1 when no XSAVE
x86/fpu: Fix early FPU command-line parsing
x86/mm: Use PAGE_ALIGNED instead of IS_ALIGNED
selftests/x86: Disable the ldt_gdt_64 test for now
x86/mm/pat: Make split_page_count() check for empty levels to fix /proc/meminfo output
x86/boot: Double BOOT_HEAP_SIZE to 64KB
x86/mm: Add barriers and document switch_mm()-vs-flush synchronization
Pull oower management and ACPI updates from Rafael Wysocki:
"As far as the number of commits goes, ACPICA takes the lead this time,
followed by cpufreq and the device properties framework changes.
The most significant new feature is the debugfs-based interface to the
ACPICA's AML debugger added in the previous cycle and a new user space
tool for accessing it.
On the cpufreq front, the core is updated to handle governors more
efficiently, particularly on systems where a single cpufreq policy
object is shared between multiple CPUs, and there are quite a few
changes in drivers (intel_pstate, cpufreq-dt etc).
The device properties framework is updated to handle built-in (ie
included in the kernel itself) device properties better, among other
things by adding a fallback mechanism that will allow drivers to
provide default properties to be used in case the plaform firmware
doesn't provide the properties expected by them.
The Operating Performance Points (OPP) framework gets new DT bindings
and debugfs support.
A new cpufreq driver for ST platforms is added and the ACPI driver for
AMD SoCs will now support the APM X-Gene ACPI I2C device.
The rest is mostly fixes and cleanups all over.
Specifics:
- Add a debugfs-based interface for interacting with the ACPICA's AML
debugger introduced in the previous cycle and a new user space tool
for that, fix some bugs related to the AML debugger and clean up
the code in question (Lv Zheng, Dan Carpenter, Colin Ian King,
Markus Elfring).
- Update ACPICA to upstream revision 20151218 including a number of
fixes and cleanups in the ACPICA core (Bob Moore, Lv Zheng, Labbe
Corentin, Prarit Bhargava, Colin Ian King, David E Box, Rafael
Wysocki).
In particular, the previously added erroneous support for the _SUB
object is dropped, the concatenate operator will support all ACPI
objects now, the Debug Object handling is improved, the SuperName
handling of parameters being control methods is fixed, the
ObjectType operator handling is updated to follow ACPI 5.0A and the
handling of CondRefOf and RefOf is updated accordingly, module-
level code will be executed after loading each ACPI table now
(instead of being run once after all tables containing AML have
been loaded), the Operation Region handlers management is updated
to fix some reported problems and a the ACPICA code in the kernel
is more in line with the upstream now.
- Update the ACPI backlight driver to provide information on whether
or not it will generate key-presses for brightness change hotkeys
and update some platform drivers (dell-wmi, thinkpad_acpi) to use
that information to avoid sending double key-events to users pace
for these, add new ACPI backlight quirks (Hans de Goede, Aaron Lu,
Adrien Schildknecht).
- Improve the ACPI handling of interrupt GPIOs (Christophe Ricard).
- Fix the handling of the list of device IDs of device objects found
in the ACPI namespace and add a helper for checking if there is a
device object for a given device ID (Lukas Wunner).
- Change the logic in the ACPI namespace scanning code to create
struct acpi_device objects for all ACPI device objects found in the
namespace even if _STA fails for them which helps to avoid device
enumeration problems on Microsoft Surface 3 (Aaron Lu).
- Add support for the APM X-Gene ACPI I2C device to the ACPI driver
for AMD SoCs (Loc Ho).
- Fix the long-standing issue with the DMA controller on Intel SoCs
where ACPI tables have no power management support for the DMA
controller itself, but it can be powered off automatically when the
last (other) device on the SoC is powered off via ACPI and clean up
the ACPI driver for Intel SoCs (acpi-lpss) after previous attempts
to fix that problem (Andy Shevchenko).
- Assorted ACPI fixes and cleanups (Andy Lutomirski, Colin Ian King,
Javier Martinez Canillas, Ken Xue, Mathias Krause, Rafael Wysocki,
Sinan Kaya).
- Update the device properties framework for better handling of
built-in properties, add support for built-in properties to the
platform bus type, update the MFD subsystem's handling of device
properties and add support for passing default configuration data
as device properties to the intel-lpss MFD drivers, convert the
designware I2C driver to use the unified device properties API and
add a fallback mechanism for using default built-in properties if
the platform firmware fails to provide the properties as expected
by drivers (Andy Shevchenko, Mika Westerberg, Heikki Krogerus,
Andrew Morton).
- Add new Device Tree bindings to the Operating Performance Points
(OPP) framework and update the exynos4412 DT binding accordingly,
introduce debugfs support for the OPP framework (Viresh Kumar,
Bartlomiej Zolnierkiewicz).
- Migrate the mt8173 cpufreq driver to the new OPP bindings (Pi-Cheng
Chen).
- Update the cpufreq core to make the handling of governors more
efficient, especially on systems where policy objects are shared
between multiple CPUs (Viresh Kumar, Rafael Wysocki).
- Fix cpufreq governor handling on configurations with
CONFIG_HZ_PERIODIC set (Chen Yu).
- Clean up the cpufreq core code related to the boost sysfs knob
support and update the ACPI cpufreq driver accordingly (Rafael
Wysocki).
- Add a new cpufreq driver for ST platforms and corresponding Device
Tree bindings (Lee Jones).
- Update the intel_pstate driver to allow the P-state selection
algorithm used by it to depend on the CPU ID of the processor it is
running on, make it use a special P-state selection algorithm (with
an IO wait time compensation tweak) on Atom CPUs based on the
Airmont and Silvermont cores so as to reduce their energy
consumption and improve intel_pstate documentation (Philippe
Longepe, Srinivas Pandruvada).
- Update the cpufreq-dt driver to support registering cooling devices
that use the (P * V^2 * f) dynamic power draw formula where V is
the voltage, f is the frequency and P is a constant coefficient
provided by Device Tree and update the arm_big_little cpufreq
driver to use that support (Punit Agrawal).
- Assorted cpufreq driver (cpufreq-dt, qoriq, pcc-cpufreq,
blackfin-cpufreq) updates (Andrzej Hajda, Hongtao Jia, Jacob
Tanenbaum, Markus Elfring).
- cpuidle core tweaks related to polling and measured_us calculation
(Rik van Riel).
- Removal of modularity from a few cpuidle drivers (clps711x, ux500,
exynos) that cannot be built as modules in practice (Paul
Gortmaker).
- PM core update to prevent devices from being probed during system
suspend/resume which is generally problematic and may lead to
inconsistent behavior (Grygorii Strashko).
- Assorted updates of the PM core and related code (Julia Lawall,
Manuel Pégourié-Gonnard, Maruthi Bayyavarapu, Rafael Wysocki, Ulf
Hansson).
- PNP bus type updates (Christophe Le Roy, Heiner Kallweit).
- PCI PM code cleanups (Jarkko Nikula, Julia Lawall).
- cpupower tool updates (Jacob Tanenbaum, Thomas Renninger)"
* tag 'pm+acpi-4.5-rc1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (177 commits)
PM / clk: don't leave clocks enabled when driver not bound
i2c: dw: Add APM X-Gene ACPI I2C device support
ACPI / APD: Add APM X-Gene ACPI I2C device support
ACPI / LPSS: change 'does not have' to 'has' in comment
Revert "dmaengine: dw: platform: provide platform data for Intel"
dmaengine: dw: return immediately from IRQ when DMA isn't in use
dmaengine: dw: platform: power on device on shutdown
ACPI / LPSS: override power state for LPSS DMA device
PM / OPP: Use snprintf() instead of sprintf()
Documentation: cpufreq: intel_pstate: enhance documentation
ACPI, PCI, irq: remove redundant check for null string pointer
ACPI / video: driver must be registered before checking for keypresses
cpufreq-dt: fix handling regulator_get_voltage() result
cpufreq: governor: Fix negative idle_time when configured with CONFIG_HZ_PERIODIC
PM / sleep: Add support for read-only sysfs attributes
ACPI: Fix white space in a structure definition
ACPI / SBS: fix inconsistent indenting inside if statement
PNP: respect PNP_DRIVER_RES_DO_NOT_CHANGE when detaching
ACPI / PNP: constify device IDs
ACPI / PCI: Simplify acpi_penalize_isa_irq()
...
Pull KVM updates from Paolo Bonzini:
"PPC changes will come next week.
- s390: Support for runtime instrumentation within guests, support of
248 VCPUs.
- ARM: rewrite of the arm64 world switch in C, support for 16-bit VM
identifiers. Performance counter virtualization missed the boat.
- x86: Support for more Hyper-V features (synthetic interrupt
controller), MMU cleanups"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (115 commits)
kvm: x86: Fix vmwrite to SECONDARY_VM_EXEC_CONTROL
kvm/x86: Hyper-V SynIC timers tracepoints
kvm/x86: Hyper-V SynIC tracepoints
kvm/x86: Update SynIC timers on guest entry only
kvm/x86: Skip SynIC vector check for QEMU side
kvm/x86: Hyper-V fix SynIC timer disabling condition
kvm/x86: Reorg stimer_expiration() to better control timer restart
kvm/x86: Hyper-V unify stimer_start() and stimer_restart()
kvm/x86: Drop stimer_stop() function
kvm/x86: Hyper-V timers fix incorrect logical operation
KVM: move architecture-dependent requests to arch/
KVM: renumber vcpu->request bits
KVM: document which architecture uses each request bit
KVM: Remove unused KVM_REQ_KICK to save a bit in vcpu->requests
kvm: x86: Check kvm_write_guest return value in kvm_write_wall_clock
KVM: s390: implement the RI support of guest
kvm/s390: drop unpaired smp_mb
kvm: x86: fix comment about {mmu,nested_mmu}.gva_to_gpa
KVM: x86: MMU: Use clear_page() instead of init_shadow_page_table()
arm/arm64: KVM: Detect vGIC presence at runtime
...
Pull xen updates from David Vrabel:
"Xen features and fixes for 4.5-rc0:
- Stolen ticks and PV wallclock support for arm/arm64
- Add grant copy ioctl to gntdev device"
* tag 'for-linus-4.5-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/gntdev: add ioctl for grant copy
x86/xen: don't reset vcpu_info on a cancelled suspend
xen/gntdev: constify mmu_notifier_ops structures
xen/grant-table: constify gnttab_ops structure
xen/time: use READ_ONCE
xen/x86: convert remaining timespec to timespec64 in xen_pvclock_gtod_notify
xen/x86: support XENPF_settime64
xen/arm: set the system time in Xen via the XENPF_settime64 hypercall
xen/arm: introduce xen_read_wallclock
arm: extend pvclock_wall_clock with sec_hi
xen: introduce XENPF_settime64
xen/arm: introduce HYPERVISOR_platform_op on arm and arm64
xen: rename dom0_op to platform_op
xen/arm: account for stolen ticks
arm64: introduce CONFIG_PARAVIRT, PARAVIRT_TIME_ACCOUNTING and pv_time_ops
arm: introduce CONFIG_PARAVIRT, PARAVIRT_TIME_ACCOUNTING and pv_time_ops
missing include asm/paravirt.h in cputime.c
xen: move xen_setup_runstate_info and get_runstate_snapshot to drivers/xen/time.c
This defines __smp_xxx barriers for x86,
for use by virtualization.
smp_xxx barriers are removed as they are
defined correctly by asm-generic/barriers.h
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
As on most architectures, on x86 read_barrier_depends and
smp_read_barrier_depends are empty. Drop the local definitions and pull
the generic ones from asm-generic/barrier.h instead: they are identical.
This is in preparation to refactoring this code area.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Pavel noted that lguest maps the switcher code executable and
read-write. This is a bad idea for any kernel text, but
particularly for text mapped at a fixed address.
Create two vmas, one for the text (PAGE_KERNEL_RX) and another
for the stacks (PAGE_KERNEL). Use VM_NO_GUARD to map them
adjacent (as expected by the rest of the code).
Reported-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
It makes me uncomfortable that even modern systems grant every
process direct read access to the HPET.
While fixing this for real without regressing anything is a mess
(unmapping the HPET is tricky because we don't adequately track
all the mappings), we can do almost as well by tracking which
vclocks have ever been used and only allowing pages associated
with used vclocks to be faulted in.
This will cause rogue programs that try to peek at the HPET to
get SIGBUS instead on most systems.
We can't restrict faults to vclock pages that are associated
with the currently selected vclock due to a race: a process
could start to access the HPET for the first time and race
against a switch away from the HPET as the current clocksource.
We can't segfault the process trying to peek at the HPET in this
case, even though the process isn't going to do anything useful
with the data.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/e79d06295625c02512277737ab55085a498ac5d8.1451446564.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When "eagerfpu=off" is given as a command-line input, the kernel
should disable AVX support.
The Task Switched bit used for lazy context switching does not
support AVX. If AVX is enabled without eagerfpu context
switching, one task's AVX state could become corrupted or leak
to other tasks. This is a bug and has bad security implications.
This only affects systems that have AVX/AVX2/AVX512 and this
issue will be found only when one actually uses AVX/AVX2/AVX512
_AND_ does eagerfpu=off.
Reference: Intel Software Developer's Manual Vol. 3A
Sec. 2.5 Control Registers:
TS Task Switched bit (bit 3 of CR0) -- Allows the saving of the
x87 FPU/ MMX/SSE/SSE2/SSE3/SSSE3/SSE4 context on a task switch
to be delayed until an x87 FPU/MMX/SSE/SSE2/SSE3/SSSE3/SSE4
instruction is actually executed by the new task.
Sec. 13.4.1 Using the TS Flag to Control the Saving of the X87
FPU and SSE State
When the TS flag is set, the processor monitors the instruction
stream for x87 FPU, MMX, SSE instructions. When the processor
detects one of these instructions, it raises a
device-not-available exeception (#NM) prior to executing the
instruction.
Signed-off-by: Yu-cheng Yu <yu-cheng.yu@intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Borislav Petkov <bp@suse.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Cc: Ravi V. Shankar <ravi.v.shankar@intel.com>
Cc: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: yu-cheng yu <yu-cheng.yu@intel.com>
Link: http://lkml.kernel.org/r/1452119094-7252-5-git-send-email-yu-cheng.yu@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull x86 platform updates from Ingo Molnar:
"Two changes:
- one to quirk-save/restore certain system MSRs across
suspend/resume, to make certain Intel systems work better
(Chen Yu)
- and also to constify a read only structure (Julia Lawall)"
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/platform/calgary: Constify cal_chipset_ops structures
x86/pm: Introduce quirk framework to save/restore extra MSR registers around suspend/resume
Pull x86 fpu updates from Ingo Molnar:
"This cleans up the FPU fault handling methods to be more robust, and
moves eligible variables to .init.data"
* 'x86-fpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/fpu: Put a few variables in .init.data
x86/fpu: Get rid of xstate_fault()
x86/fpu: Add an XSTATE_OP() macro
Pull x86 cpu updates from Ingo Molnar:
"The main changes in this cycle were:
- Improved CPU ID handling code and related enhancements (Borislav
Petkov)
- RDRAND fix (Len Brown)"
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Replace RDRAND forced-reseed with simple sanity check
x86/MSR: Chop off lower 32-bit value
x86/cpu: Fix MSR value truncation issue
x86/cpu/amd, kvm: Satisfy guest kernel reads of IC_CFG MSR
kvm: Add accessors for guest CPU's family, model, stepping
x86/cpu: Unify CPU family, model, stepping calculation
* acpi-soc:
PM / clk: don't leave clocks enabled when driver not bound
i2c: dw: Add APM X-Gene ACPI I2C device support
ACPI / APD: Add APM X-Gene ACPI I2C device support
ACPI / LPSS: change 'does not have' to 'has' in comment
Revert "dmaengine: dw: platform: provide platform data for Intel"
dmaengine: dw: return immediately from IRQ when DMA isn't in use
dmaengine: dw: platform: power on device on shutdown
ACPI / LPSS: override power state for LPSS DMA device
ACPI / LPSS: power on when probe() and otherwise when remove()
ACPI / LPSS: do delay for all LPSS devices when D3->D0
ACPI / LPSS: allow to use specific PM domain during ->probe()
Revert "ACPI / LPSS: allow to use specific PM domain during ->probe()"
device core: add BUS_NOTIFY_DRIVER_NOT_BOUND notification
x86/platform/iosf_mbi: Remove duplicate definitions
Conflicts:
drivers/i2c/busses/i2c-designware-platdrv.c
Pull x86 asm updates from Ingo Molnar:
"The main changes in this cycle were:
- vDSO and asm entry improvements (Andy Lutomirski)
- Xen paravirt entry enhancements (Boris Ostrovsky)
- asm entry labels enhancement (Borislav Petkov)
- and other misc changes (Thomas Gleixner, me)"
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/vsdo: Fix build on PARAVIRT_CLOCK=y, KVM_GUEST=n
Revert "x86/kvm: On KVM re-enable (e.g. after suspend), update clocks"
x86/entry/64_compat: Make labels local
x86/platform/uv: Include clocksource.h for clocksource_touch_watchdog()
x86/vdso: Enable vdso pvclock access on all vdso variants
x86/vdso: Remove pvclock fixmap machinery
x86/vdso: Get pvclock data from the vvar VMA instead of the fixmap
x86, vdso, pvclock: Simplify and speed up the vdso pvclock reader
x86/kvm: On KVM re-enable (e.g. after suspend), update clocks
x86/entry/64: Bypass enter_from_user_mode on non-context-tracking boots
x86/asm: Add asm macros for static keys/jump labels
x86/asm: Error out if asm/jump_label.h is included inappropriately
context_tracking: Switch to new static_branch API
x86/entry, x86/paravirt: Remove the unused usergs_sysret32 PV op
x86/paravirt: Remove the unused irq_enable_sysexit pv op
x86/xen: Avoid fast syscall path for Xen PV guests
Pull x86 apic updates from Ingo Molnar:
"The main changes in this cycle were:
- introduce optimized single IPI sending methods on modern APICs
(Linus Torvalds, Thomas Gleixner)
- kexec/crash APIC handling fixes and enhancements (Hidehiro Kawai)
- extend lapic vector saving/restoring to the CMCI (MCE) vector as
well (Juergen Gross)
- various fixes and enhancements (Jake Oshins, Len Brown)"
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
x86/irq: Export functions to allow MSI domains in modules
Documentation: Document kernel.panic_on_io_nmi sysctl
x86/nmi: Save regs in crash dump on external NMI
x86/apic: Introduce apic_extnmi command line parameter
kexec: Fix race between panic() and crash_kexec()
panic, x86: Allow CPUs to save registers even if looping in NMI context
panic, x86: Fix re-entrance problem due to panic on NMI
x86/apic: Fix the saving and restoring of lapic vectors during suspend/resume
x86/smpboot: Re-enable init_udelay=0 by default on modern CPUs
x86/smp: Remove single IPI wrapper
x86/apic: Use default send single IPI wrapper
x86/apic: Provide default send single IPI wrapper
x86/apic: Implement single IPI for apic_noop
x86/apic: Wire up single IPI for apic_numachip
x86/apic: Wire up single IPI for x2apic_uv
x86/apic: Implement single IPI for x2apic_phys
x86/apic: Wire up single IPI for bigsmp_apic
x86/apic: Remove pointless indirections from bigsmp_apic
x86/apic: Wire up single IPI for apic_physflat
x86/apic: Remove pointless indirections from apic_physflat
...
Pull RAS updates from Ingo Molnar:
"Various x86 MCE fixes and small enhancements"
* 'ras-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mce: Make usable address checks Intel-only
x86/mce: Add the missing memory error check on AMD
x86/RAS: Remove mce.usable_addr
x86/mce: Do not enter deferred errors into the generic pool twice
Pull perf updates from Ingo Molnar:
"Kernel side changes:
- Intel Knights Landing support. (Harish Chegondi)
- Intel Broadwell-EP uncore PMU support. (Kan Liang)
- Core code improvements. (Peter Zijlstra.)
- Event filter, LBR and PEBS fixes. (Stephane Eranian)
- Enable cycles:pp on Intel Atom. (Stephane Eranian)
- Add cycles:ppp support for Skylake. (Andi Kleen)
- Various x86 NMI overhead optimizations. (Andi Kleen)
- Intel PT enhancements. (Takao Indoh)
- AMD cache events fix. (Vince Weaver)
Tons of tooling changes:
- Show random perf tool tips in the 'perf report' bottom line
(Namhyung Kim)
- perf report now defaults to --group if the perf.data file has
grouped events, try it with:
# perf record -e '{cycles,instructions}' -a sleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 1.093 MB perf.data (1247 samples) ]
# perf report
# Samples: 1K of event 'anon group { cycles, instructions }'
# Event count (approx.): 1955219195
#
# Overhead Command Shared Object Symbol
2.86% 0.22% swapper [kernel.kallsyms] [k] intel_idle
1.05% 0.33% firefox libxul.so [.] js::SetObjectElement
1.05% 0.00% kworker/0:3 [kernel.kallsyms] [k] gen6_ring_get_seqno
0.88% 0.17% chrome chrome [.] 0x0000000000ee27ab
0.65% 0.86% firefox libxul.so [.] js::ValueToId<(js::AllowGC)1>
0.64% 0.23% JS Helper libxul.so [.] js::SplayTree<js::jit::LiveRange*, js::jit::LiveRange>::splay
0.62% 1.27% firefox libxul.so [.] js::GetIterator
0.61% 1.74% firefox libxul.so [.] js::NativeSetProperty
0.61% 0.31% firefox libxul.so [.] js::SetPropertyByDefining
- Introduce the 'perf stat record/report' workflow:
Generate perf.data files from 'perf stat', to tap into the
scripting capabilities perf has instead of defining a 'perf stat'
specific scripting support to calculate event ratios, etc.
Simple example:
$ perf stat record -e cycles usleep 1
Performance counter stats for 'usleep 1':
1,134,996 cycles
0.000670644 seconds time elapsed
$ perf stat report
Performance counter stats for '/home/acme/bin/perf stat record -e cycles usleep 1':
1,134,996 cycles
0.000670644 seconds time elapsed
$
It generates PERF_RECORD_ userspace records to store the details:
$ perf report -D | grep PERF_RECORD
0xf0 [0x28]: PERF_RECORD_THREAD_MAP nr: 1 thread: 27637
0x118 [0x12]: PERF_RECORD_CPU_MAP nr: 1 cpu: 65535
0x12a [0x40]: PERF_RECORD_STAT_CONFIG
0x16a [0x30]: PERF_RECORD_STAT
-1 -1 0x19a [0x40]: PERF_RECORD_MMAP -1/0: [0xffffffff81000000(0x1f000000) @ 0xffffffff81000000]: x [kernel.kallsyms]_text
0x1da [0x18]: PERF_RECORD_STAT_ROUND
[acme@ssdandy linux]$
An effort was made to make perf.data files generated like this to
not generate cryptic messages when processed by older tools.
The 'perf script' bits need rebasing, will go up later.
- Make command line options always available, even when they depend
on some feature being enabled, warning the user about use of such
options (Wang Nan)
- Support hw breakpoint events (mem:0xAddress) in the default output
mode in 'perf script' (Wang Nan)
- Fixes and improvements for supporting annotating ARM binaries,
support ARM call and jump instructions, more work needed to have
arch specific stuff separated into tools/perf/arch/*/annotate/
(Russell King)
- Add initial 'perf config' command, for now just with a --list
command to the contents of the configuration file in use and a
basic man page describing its format, commands for doing edits and
detailed documentation are being reviewed and proof-read. (Taeung
Song)
- Allows BPF scriptlets specify arguments to be fetched using DWARF
info, using a prologue generated at compile/build time (He Kuang,
Wang Nan)
- Allow attaching BPF scriptlets to module symbols (Wang Nan)
- Allow attaching BPF scriptlets to userspace code using uprobe (Wang
Nan)
- BPF programs now can specify 'perf probe' tunables via its section
name, separating key=val values using semicolons (Wang Nan)
Testing some of these new BPF features:
Use case: get callchains when receiving SSL packets, filter then in the
kernel, at arbitrary place.
# cat ssl.bpf.c
#define SEC(NAME) __attribute__((section(NAME), used))
struct pt_regs;
SEC("func=__inet_lookup_established hnum")
int func(struct pt_regs *ctx, int err, unsigned short port)
{
return err == 0 && port == 443;
}
char _license[] SEC("license") = "GPL";
int _version SEC("version") = LINUX_VERSION_CODE;
#
# perf record -a -g -e ssl.bpf.c
^C[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.787 MB perf.data (3 samples) ]
# perf script | head -30
swapper 0 [000] 58783.268118: perf_bpf_probe:func: (ffffffff816a0f60) hnum=0x1bb
8a0f61 __inet_lookup_established (/lib/modules/4.3.0+/build/vmlinux)
896def ip_rcv_finish (/lib/modules/4.3.0+/build/vmlinux)
8976c2 ip_rcv (/lib/modules/4.3.0+/build/vmlinux)
855eba __netif_receive_skb_core (/lib/modules/4.3.0+/build/vmlinux)
8565d8 __netif_receive_skb (/lib/modules/4.3.0+/build/vmlinux)
8572a8 process_backlog (/lib/modules/4.3.0+/build/vmlinux)
856b11 net_rx_action (/lib/modules/4.3.0+/build/vmlinux)
2a284b __do_softirq (/lib/modules/4.3.0+/build/vmlinux)
2a2ba3 irq_exit (/lib/modules/4.3.0+/build/vmlinux)
96b7a4 do_IRQ (/lib/modules/4.3.0+/build/vmlinux)
969807 ret_from_intr (/lib/modules/4.3.0+/build/vmlinux)
2dede5 cpu_startup_entry (/lib/modules/4.3.0+/build/vmlinux)
95d5bc rest_init (/lib/modules/4.3.0+/build/vmlinux)
1163ffa start_kernel ([kernel.vmlinux].init.text)
11634d7 x86_64_start_reservations ([kernel.vmlinux].init.text)
1163623 x86_64_start_kernel ([kernel.vmlinux].init.text)
qemu-system-x86 9178 [003] 58785.792417: perf_bpf_probe:func: (ffffffff816a0f60) hnum=0x1bb
8a0f61 __inet_lookup_established (/lib/modules/4.3.0+/build/vmlinux)
896def ip_rcv_finish (/lib/modules/4.3.0+/build/vmlinux)
8976c2 ip_rcv (/lib/modules/4.3.0+/build/vmlinux)
855eba __netif_receive_skb_core (/lib/modules/4.3.0+/build/vmlinux)
8565d8 __netif_receive_skb (/lib/modules/4.3.0+/build/vmlinux)
856660 netif_receive_skb_internal (/lib/modules/4.3.0+/build/vmlinux)
8566ec netif_receive_skb_sk (/lib/modules/4.3.0+/build/vmlinux)
430a br_handle_frame_finish ([bridge])
48bc br_handle_frame ([bridge])
855f44 __netif_receive_skb_core (/lib/modules/4.3.0+/build/vmlinux)
8565d8 __netif_receive_skb (/lib/modules/4.3.0+/build/vmlinux)
#
- Use 'perf probe' various options to list functions, see what
variables can be collected at any given point, experiment first
collecting without a filter, then filter, use it together with
'perf trace', 'perf top', with or without callchains, if it
explodes, please tell us!
- Introduce a new callchain mode: "folded", that will list per line
representations of all callchains for a give histogram entry,
facilitating 'perf report' output processing by other tools, such
as Brendan Gregg's flamegraph tools (Namhyung Kim)
E.g:
# perf report | grep -v ^# | head
18.37% 0.00% swapper [kernel.kallsyms] [k] cpu_startup_entry
|
---cpu_startup_entry
|
|--12.07%--start_secondary
|
--6.30%--rest_init
start_kernel
x86_64_start_reservations
x86_64_start_kernel
#
Becomes, in "folded" mode:
# perf report -g folded | grep -v ^# | head -5
18.37% 0.00% swapper [kernel.kallsyms] [k] cpu_startup_entry
12.07% cpu_startup_entry;start_secondary
6.30% cpu_startup_entry;rest_init;start_kernel;x86_64_start_reservations;x86_64_start_kernel
16.90% 0.00% swapper [kernel.kallsyms] [k] call_cpuidle
11.23% call_cpuidle;cpu_startup_entry;start_secondary
5.67% call_cpuidle;cpu_startup_entry;rest_init;start_kernel;x86_64_start_reservations;x86_64_start_kernel
16.90% 0.00% swapper [kernel.kallsyms] [k] cpuidle_enter
11.23% cpuidle_enter;call_cpuidle;cpu_startup_entry;start_secondary
5.67% cpuidle_enter;call_cpuidle;cpu_startup_entry;rest_init;start_kernel;x86_64_start_reservations;x86_64_start_kernel
15.12% 0.00% swapper [kernel.kallsyms] [k] cpuidle_enter_state
#
The user can also select one of "count", "period" or "percent" as
the first column.
... and lots of infrastructure enhancements, plus fixes and other
changes, features I failed to list - see the shortlog and the git log
for details"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (271 commits)
perf evlist: Add --trace-fields option to show trace fields
perf record: Store data mmaps for dwarf unwind
perf libdw: Check for mmaps also in MAP__VARIABLE tree
perf unwind: Check for mmaps also in MAP__VARIABLE tree
perf unwind: Use find_map function in access_dso_mem
perf evlist: Remove perf_evlist__(enable|disable)_event functions
perf evlist: Make perf_evlist__open() open evsels with their cpus and threads (like perf record does)
perf report: Show random usage tip on the help line
perf hists: Export a couple of hist functions
perf diff: Use perf_hpp__register_sort_field interface
perf tools: Add overhead/overhead_children keys defaults via string
perf tools: Remove list entry from struct sort_entry
perf tools: Include all tools/lib directory for tags/cscope/TAGS targets
perf script: Align event name properly
perf tools: Add missing headers in perf's MANIFEST
perf tools: Do not show trace command if it's not compiled in
perf report: Change default to use event group view
perf top: Decay periods in callchains
tools lib: Move bitmap.[ch] from tools/perf/ to tools/{lib,include}/
tools lib: Sync tools/lib/find_bit.c with the kernel
...
Pull locking updates from Ingo Molnar:
"So we have a laundry list of locking subsystem changes:
- continuing barrier API and code improvements
- futex enhancements
- atomics API improvements
- pvqspinlock enhancements: in particular lock stealing and adaptive
spinning
- qspinlock micro-enhancements"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex: Allow FUTEX_CLOCK_REALTIME with FUTEX_WAIT op
futex: Cleanup the goto confusion in requeue_pi()
futex: Remove pointless put_pi_state calls in requeue()
futex: Document pi_state refcounting in requeue code
futex: Rename free_pi_state() to put_pi_state()
futex: Drop refcount if requeue_pi() acquired the rtmutex
locking/barriers, arch: Remove ambiguous statement in the smp_store_mb() documentation
lcoking/barriers, arch: Use smp barriers in smp_store_release()
locking/cmpxchg, arch: Remove tas() definitions
locking/pvqspinlock: Queue node adaptive spinning
locking/pvqspinlock: Allow limited lock stealing
locking/pvqspinlock: Collect slowpath lock statistics
sched/core, locking: Document Program-Order guarantees
locking, sched: Introduce smp_cond_acquire() and use it
locking/pvqspinlock, x86: Optimize the PV unlock code path
locking/qspinlock: Avoid redundant read of next pointer
locking/qspinlock: Prefetch the next node cacheline
locking/qspinlock: Use _acquire/_release() versions of cmpxchg() & xchg()
atomics: Add test for atomic operations with _relaxed variants
Since the numbers now overlap, it makes sense to enumerate
them in asm/kvm_host.h rather than linux/kvm_host.h. Functions
that refer to architecture-specific requests are also moved
to arch/.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM/ARM changes for Linux v4.5
- Complete rewrite of the arm64 world switch in C, hopefully
paving the way for more sharing with the 32bit code, better
maintainability and easier integration of new features.
Also smaller and slightly faster in some cases...
- Support for 16bit VM identifiers
- Various cleanups
The dom0_op hypercall has been renamed to platform_op since Xen 3.2,
which is ancient, and modern upstream Linux kernels cannot run as dom0
and it anymore anyway.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Adding the rtc platform device in non-privileged Xen PV guests causes
an IRQ conflict because these guests do not have legacy PIC and may
allocate irqs in the legacy range.
In a single VCPU Xen PV guest we should have:
/proc/interrupts:
CPU0
0: 4934 xen-percpu-virq timer0
1: 0 xen-percpu-ipi spinlock0
2: 0 xen-percpu-ipi resched0
3: 0 xen-percpu-ipi callfunc0
4: 0 xen-percpu-virq debug0
5: 0 xen-percpu-ipi callfuncsingle0
6: 0 xen-percpu-ipi irqwork0
7: 321 xen-dyn-event xenbus
8: 90 xen-dyn-event hvc_console
...
But hvc_console cannot get its interrupt because it is already in use
by rtc0 and the console does not work.
genirq: Flags mismatch irq 8. 00000000 (hvc_console) vs. 00000000 (rtc0)
We can avoid this problem by realizing that unprivileged PV guests (both
Xen and lguests) are not supposed to have rtc_cmos device and so
adding it is not necessary.
Privileged guests (i.e. Xen's dom0) do use it but they should not have
irq conflicts since they allocate irqs above legacy range (above
gsi_top, in fact).
Instead of explicitly testing whether the guest is privileged we can
extend pv_info structure to include information about guest's RTC
support.
Reported-and-tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: vkuznets@redhat.com
Cc: xen-devel@lists.xenproject.org
Cc: konrad.wilk@oracle.com
Cc: stable@vger.kernel.org # 4.2+
Link: http://lkml.kernel.org/r/1449842873-2613-1-git-send-email-boris.ostrovsky@oracle.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add definitions for MERR_DPCM_DEEP_BUFFER AND PIPE_MEDIA3_IN
Add relevant cpu-dai and dai link names
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now, multiple CPUs can receive an external NMI simultaneously by
specifying the "apic_extnmi=all" command line parameter. When we take
a crash dump by using external NMI with this option, we fail to save
registers into the crash dump. This happens as follows:
CPU 0 CPU 1
================================ =============================
receive an external NMI
default_do_nmi() receive an external NMI
spin_lock(&nmi_reason_lock) default_do_nmi()
io_check_error() spin_lock(&nmi_reason_lock)
panic() busy loop
...
kdump_nmi_shootdown_cpus()
issue NMI IPI -----------> blocked until IRET
busy loop...
Here, since CPU 1 is in NMI context, an additional NMI from CPU 0
remains unhandled until CPU 1 IRETs. However, CPU 1 will never execute
IRET so the NMI is not handled and the callback function to save
registers is never called.
To solve this issue, we check if the IPI for crash dumping was issued
while waiting for nmi_reason_lock to be released, and if so, call its
callback function directly. If the IPI is not issued (e.g. kdump is
disabled), the actual behavior doesn't change.
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Baoquan He <bhe@redhat.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: kexec@lists.infradead.org
Cc: linux-doc@vger.kernel.org
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: x86-ml <x86@kernel.org>
Link: http://lkml.kernel.org/r/20151210065245.4587.39316.stgit@softrs
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
