Pull ARM SoC driver updates from Arnd Bergmann:
"This contains driver changes that are tightly connected to SoC
specific code. Aside from smaller cleanups and bug fixes, here is a
list of the notable changes.
New device drivers:
- The Turris Mox router has a new "moxtet" bus driver for its
on-board pluggable extension bus. The same platform also gains a
firmware driver.
- The Samsung Exynos family gains a new Chipid driver exporting using
the soc device sysfs interface
- A similar socinfo driver for Qualcomm Snapdragon chips.
- A firmware driver for the NXP i.MX DSP IPC protocol using shared
memory and a mailbox
Other changes:
- The i.MX reset controller driver now supports the NXP i.MX8MM chip
- Amlogic SoC specific drivers gain support for the S905X3 and A311D
chips
- A rework of the TI Davinci framebuffer driver to allow important
cleanups in the platform code
- A couple of device drivers for removed ARM SoC platforms are
removed. Most of the removals were picked up by other maintainers,
this contains whatever was left"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
bus: uniphier-system-bus: use devm_platform_ioremap_resource()
soc: ti: ti_sci_pm_domains: Add support for exclusive and shared access
dt-bindings: ti_sci_pm_domains: Add support for exclusive and shared access
firmware: ti_sci: Allow for device shared and exclusive requests
bus: imx-weim: remove incorrect __init annotations
fbdev: remove w90x900/nuc900 platform drivers
spi: remove w90x900 driver
net: remove w90p910-ether driver
net: remove ks8695 driver
firmware: turris-mox-rwtm: Add sysfs documentation
firmware: Add Turris Mox rWTM firmware driver
dt-bindings: firmware: Document cznic,turris-mox-rwtm binding
bus: moxtet: fix unsigned comparison to less than zero
bus: moxtet: remove set but not used variable 'dummy'
ARM: scoop: Use the right include
dt-bindings: power: add Amlogic Everything-Else power domains bindings
soc: amlogic: Add support for Everything-Else power domains controller
fbdev: da8xx: use resource management for dma
fbdev: da8xx-fb: drop a redundant if
fbdev: da8xx-fb: use devm_platform_ioremap_resource()
...
Pull ARM SoC platform updates from Arnd Bergmann:
"The main change this time around is a cleanup of some of the oldest
platforms based on the XScale and ARM9 CPU cores, which are between 10
and 20 years old.
The Kendin/Micrel/Microchip KS8695, Winbond/Nuvoton W90x900 and Intel
IOP33x/IOP13xx platforms are removed after we determined that nobody
is using them any more.
The TI Davinci and NXP LPC32xx platforms on the other hand are still
in active use and are converted to the ARCH_MULTIPLATFORM build,
meaning that we can compile a kernel that works on these along with
most other ARMv5 platforms. Changes toward that goal are also merged
for IOP32x, but additional work is needed to complete this. Patches
for the remaining ARMv5 platforms have started but need more work and
some testing.
Support for the new ASpeed AST2600 gets added, this is based on the
Cortex-A7 ARMv7 core, and is a newer version of the existing ARMv5 and
ARMv6 chips in the same family.
Other changes include a cleanup of the ST-Ericsson ux500 platform and
the move of the TI Davinci platform to a new clocksource driver"
[ The changes had marked INTEL_IOP_ADMA and USB_LPC32XX as being
buildable on other platforms through COMPILE_TEST, but that causes new
warnings that I most definitely do not want to see during the merge
window as that could hide other issues.
So the COMPILE_TEST option got disabled for them again - Linus ]
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (61 commits)
ARM: multi_v5_defconfig: make DaVinci part of the ARM v5 multiplatform build
ARM: davinci: support multiplatform build for ARM v5
arm64: exynos: Enable exynos-chipid driver
ARM: OMAP2+: Delete an unnecessary kfree() call in omap_hsmmc_pdata_init()
ARM: OMAP2+: move platform-specific asm-offset.h to arch/arm/mach-omap2
ARM: davinci: dm646x: Fix a typo in the comment
ARM: davinci: dm646x: switch to using the clocksource driver
ARM: davinci: dm644x: switch to using the clocksource driver
ARM: aspeed: Enable SMP boot
ARM: aspeed: Add ASPEED AST2600 architecture
ARM: aspeed: Select timer in each SoC
dt-bindings: arm: cpus: Add ASPEED SMP
ARM: imx: stop adjusting ar8031 phy tx delay
mailmap: map old company name to new one @microchip.com
MAINTAINERS: at91: remove the TC entry
MAINTAINERS: at91: Collect all pinctrl/gpio drivers in same entry
ARM: at91: move platform-specific asm-offset.h to arch/arm/mach-at91
MAINTAINERS: Extend patterns for Samsung SoC, Security Subsystem and clock drivers
ARM: s3c64xx: squash samsung_usb_phy.h into setup-usb-phy.c
ARM: debug-ll: Add support for r7s9210
...
Pull arm64 updates from Will Deacon:
"Although there isn't tonnes of code in terms of line count, there are
a fair few headline features which I've noted both in the tag and also
in the merge commits when I pulled everything together.
The part I'm most pleased with is that we had 35 contributors this
time around, which feels like a big jump from the usual small group of
core arm64 arch developers. Hopefully they all enjoyed it so much that
they'll continue to contribute, but we'll see.
It's probably worth highlighting that we've pulled in a branch from
the risc-v folks which moves our CPU topology code out to where it can
be shared with others.
Summary:
- 52-bit virtual addressing in the kernel
- New ABI to allow tagged user pointers to be dereferenced by
syscalls
- Early RNG seeding by the bootloader
- Improve robustness of SMP boot
- Fix TLB invalidation in light of recent architectural
clarifications
- Support for i.MX8 DDR PMU
- Remove direct LSE instruction patching in favour of static keys
- Function error injection using kprobes
- Support for the PPTT "thread" flag introduced by ACPI 6.3
- Move PSCI idle code into proper cpuidle driver
- Relaxation of implicit I/O memory barriers
- Build with RELR relocations when toolchain supports them
- Numerous cleanups and non-critical fixes"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (114 commits)
arm64: remove __iounmap
arm64: atomics: Use K constraint when toolchain appears to support it
arm64: atomics: Undefine internal macros after use
arm64: lse: Make ARM64_LSE_ATOMICS depend on JUMP_LABEL
arm64: asm: Kill 'asm/atomic_arch.h'
arm64: lse: Remove unused 'alt_lse' assembly macro
arm64: atomics: Remove atomic_ll_sc compilation unit
arm64: avoid using hard-coded registers for LSE atomics
arm64: atomics: avoid out-of-line ll/sc atomics
arm64: Use correct ll/sc atomic constraints
jump_label: Don't warn on __exit jump entries
docs/perf: Add documentation for the i.MX8 DDR PMU
perf/imx_ddr: Add support for AXI ID filtering
arm64: kpti: ensure patched kernel text is fetched from PoU
arm64: fix fixmap copy for 16K pages and 48-bit VA
perf/smmuv3: Validate groups for global filtering
perf/smmuv3: Validate group size
arm64: Relax Documentation/arm64/tagged-pointers.rst
arm64: kvm: Replace hardcoded '1' with SYS_PAR_EL1_F
arm64: mm: Ignore spurious translation faults taken from the kernel
...
Pull iommu updates from Joerg Roedel:
- batched unmap support for the IOMMU-API
- support for unlocked command queueing in the ARM-SMMU driver
- rework the ATS support in the ARM-SMMU driver
- more refactoring in the ARM-SMMU driver to support hardware
implemention specific quirks and errata
- bounce buffering DMA-API implementatation in the Intel VT-d driver
for untrusted devices (like Thunderbolt devices)
- fixes for runtime PM support in the OMAP iommu driver
- MT8183 IOMMU support in the Mediatek IOMMU driver
- rework of the way the IOMMU core sets the default domain type for
groups. Changing the default domain type on x86 does not require two
kernel parameters anymore.
- more smaller fixes and cleanups
* tag 'iommu-updates-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (113 commits)
iommu/vt-d: Declare Broadwell igfx dmar support snafu
iommu/vt-d: Add Scalable Mode fault information
iommu/vt-d: Use bounce buffer for untrusted devices
iommu/vt-d: Add trace events for device dma map/unmap
iommu/vt-d: Don't switch off swiotlb if bounce page is used
iommu/vt-d: Check whether device requires bounce buffer
swiotlb: Split size parameter to map/unmap APIs
iommu/omap: Mark pm functions __maybe_unused
iommu/ipmmu-vmsa: Disable cache snoop transactions on R-Car Gen3
iommu/ipmmu-vmsa: Move IMTTBCR_SL0_TWOBIT_* to restore sort order
iommu: Don't use sme_active() in generic code
iommu/arm-smmu-v3: Fix build error without CONFIG_PCI_ATS
iommu/qcom: Use struct_size() helper
iommu: Remove wrong default domain comments
iommu/dma: Fix for dereferencing before null checking
iommu/mediatek: Clean up struct mtk_smi_iommu
memory: mtk-smi: Get rid of need_larbid
iommu/mediatek: Fix VLD_PA_RNG register backup when suspend
memory: mtk-smi: Add bus_sel for mt8183
memory: mtk-smi: Invoke pm runtime_callback to enable clocks
...
Pull GPIO updates from Linus Walleij:
"This is the bulk of changes in the GPIO subsystem for the v5.4 kernel
cycle.
Core changes:
- Support hierarchical GPIO irqchips.
We now have three consumers that can use this: Intel IXP4xx,
ThunderX and Qualcomm SPMI GPIO (in the pinctrl subsystem).
The support code has been long in the making and hashed out so it
should be easily adaptable for all hierarchical irqchip parents.
The code only gets compiled in if hierarchical irqchip is used at
the topmost irq controller at least, as the hierarchical irqchip
requires strict hierarchy all the way up in the system.
- Determine the need for a "valid_mask" for GPIO lines on the
gpio_chip and conversely for the "valid_mask" for the GPIO
interrupt chip interrupt lines by looking for a .init_valid_mask()
callback in the main chip or GPIO interrupt chip respectively.
Allocate it with bitmap_alloc().
- Isolate the device tree/open firmware GPIO description code out in
its own file properly.
- Isolate the ACPI GPIO description code out in its own file
properly.
- Drop a whole lot of #ifdef:s in the main includes: it does not hurt
to keep the include items around, and we get quicker and clearer
compile failures if the appropriate kernel symbols are not selected
for drivers.
New/deleted drivers:
- New driver for Aspeed SGPIO.
- The KS8695 driver is deleted as the platform gets deleted from
arch/arm in this kernel cycle.
- The Cirrus Logic Madera driver now supports CS47L92 and CS47L15.
- The Freescale MPC8xxx now supports LS1028A and LS1088A.
Driver improvements:
- We pass the GPIO irqchip intialization by directly filling in the
struct instead of using set-up functions (the new way) for Intel
MID, Lynxpoint, Merrifield, XLP, HLWD, Aspeed, ZX, VF610, TQMX86,
MT7621, Zynq and EP93xx.
Out-of-band changes:
- Fix a GPIO header inclusion in Unicore - no response from
maintainer.
- Drop FMC subsystem from MAINTAINERS - was deleted in the GPIO tree
last cycle so let's mop up the shards"
* tag 'gpio-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (82 commits)
gpiolib: of: add a fallback for wlf,reset GPIO name
gpio: htc-egpio: Remove unused exported htc_egpio_get_wakeup_irq()
gpio: remove explicit comparison with 0
gpio: creg-snps: use devm_platform_ioremap_resource() to simplify code
gpio: devres: Switch to EXPORT_SYMBOL_GPL()
gpio: of: Switch to EXPORT_SYMBOL_GPL()
gpio: of: Make of_gpio_simple_xlate() private
gpio: of: Make of_get_named_gpiod_flags() private
gpio: aspeed: Add in ast2600 details to Aspeed driver
gpio: aspeed: Use ngpio property from device tree if available
gpio: aspeed: Setup irqchip dynamically
gpio/aspeed: Fix incorrect number of banks
gpio: aspeed: Update documentation with ast2600 controllers
gpio: Initialize the irqchip valid_mask with a callback
gpiolib: acpi: make acpi_can_fallback_to_crs() static
gpio: Fix further merge errors
gpio: Fix up merge collision in include file
gpio: of: Normalize return code variable name
gpio: gpiolib: Normalize return code variable name
gpio: ep93xx: Pass irqchip when adding gpiochip
...
The D-Link DIR-685 had its clock polarity set as active
low using the special SPI "spi-cpol" property.
This is not correct: the datasheet clearly states:
"Fix SCL to GND level when not in use" which is
indicative that this line is active high.
After a recent fix making the GPIO-based SPI driver
force the clock line de-asserted at the beginning of
each SPI transaction this reared its ugly head: now
de-asserted was taken to mean the line should be
driven high, but it should be driven low.
Fix this up in the DTS file and the display works again.
Link: https://lore.kernel.org/r/20190915135444.11066-1-linus.walleij@linaro.org
Cc: Mark Brown <broonie@kernel.org>
Fixes: 2922d1cc16 ("spi: gpio: Add SPI_MASTER_GPIO_SS flag")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Samsung mach/soc changes for v5.4, part 2
1. Fix system restart on S3C6410 due to missing match of watchdog,
2. Enable suppor for ARM architected timers on Exynos.
* tag 'samsung-soc-5.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: exynos: Enable support for ARM architected timers
ARM: samsung: Fix system restart on S3C6410
MAINTAINERS: Extend patterns for Samsung SoC, Security Subsystem and clock drivers
ARM: s3c64xx: squash samsung_usb_phy.h into setup-usb-phy.c
ARM: exynos: Enable exynos-chipid driver
ARM: samsung: Include GPIO driver header
Link: https://lore.kernel.org/r/20190911183632.4317-2-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Now that we know we always have the dma-noncoherent.h helpers available
if we are on an architecture with support for non-coherent devices,
we can just call them directly, and remove the calls to the dma-direct
routines, including the fact that we call the dma_direct_map_page
routines but ignore the value returned from it. Instead we now have
Xen wrappers for the arch_sync_dma_for_{device,cpu} helpers that call
the special Xen versions of those routines for foreign pages.
Note that the new helpers get the physical address passed in addition
to the dma address to avoid another translation for the local cache
maintainance. The pfn_valid checks remain on the dma address as in
the old code, even if that looks a little funny.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
These routines are only used by swiotlb-xen, which cannot be modular.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
arm and arm64 can just use xen_swiotlb_dma_ops directly like x86, no
need for a pointer indirection.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Julien Grall <julien.grall@arm.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Calculate the required operation in the caller, and pass it directly
instead of recalculating it for each page, and use simple arithmetics
to get from the physical address to Xen page size aligned chunks.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Use the dma-noncoherent dev_is_dma_coherent helper instead of the home
grown variant. Note that both are always initialized to the same
value in arch_setup_dma_ops.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Julien Grall <julien.grall@arm.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Shared the duplicate arm/arm64 code in include/xen/arm/page-coherent.h.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Copy the arm64 code that uses the dma-direct/swiotlb helpers for DMA
on-coherent devices.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Currently, multi_v7_defconfig + CONFIG_FUNCTION_TRACER fails to build
with clang:
arm-linux-gnueabi-ld: kernel/softirq.o: in function `_local_bh_enable':
softirq.c:(.text+0x504): undefined reference to `mcount'
arm-linux-gnueabi-ld: kernel/softirq.o: in function `__local_bh_enable_ip':
softirq.c:(.text+0x58c): undefined reference to `mcount'
arm-linux-gnueabi-ld: kernel/softirq.o: in function `do_softirq':
softirq.c:(.text+0x6c8): undefined reference to `mcount'
arm-linux-gnueabi-ld: kernel/softirq.o: in function `irq_enter':
softirq.c:(.text+0x75c): undefined reference to `mcount'
arm-linux-gnueabi-ld: kernel/softirq.o: in function `irq_exit':
softirq.c:(.text+0x840): undefined reference to `mcount'
arm-linux-gnueabi-ld: kernel/softirq.o:softirq.c:(.text+0xa50): more undefined references to `mcount' follow
clang can emit a working mcount symbol, __gnu_mcount_nc, when
'-meabi gnu' is passed to it. Until r369147 in LLVM, this was
broken and caused the kernel not to boot with '-pg' because the
calling convention was not correct. Always build with '-meabi gnu'
when using clang but ensure that '-pg' (which is added with
CONFIG_FUNCTION_TRACER and its prereq CONFIG_HAVE_FUNCTION_TRACER)
cannot be added with it unless this is fixed (which means using
clang 10.0.0 and newer).
Link: https://github.com/ClangBuiltLinux/linux/issues/35
Link: https://bugs.llvm.org/show_bug.cgi?id=33845
Link: 16fa8b0970
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
adjust_lowmem_bounds() checks every memblocks in order to find the boundary
between lowmem and highmem. However some memblocks could be marked as NOMAP
so they are not used by kernel, which should be skipped while calculating
the boundary.
Signed-off-by: Chester Lin <clin@suse.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Add modifications necessary to make davinci part of the ARM v5
multiplatform build.
Move the arch-specific configuration out of arch/arm/Kconfig and
into mach-davinci/Kconfig. Remove the sub-menu for DaVinci
implementations (they'll be visible directly under the system type.
Select all necessary options not already selected by ARCH_MULTI_V5.
Update davinci_all_defconfig. Explicitly include the mach-specific
headers in mach-davinci/Makefile.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
ARM architected timer can be used together with Exynos MultiCore Timer
driver, so enable support for it. Support for ARM architected timers is
essential for enabling proper KVM support.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
While parts of the VGIC support a large number of vcpus (we
bravely allow up to 512), other parts are more limited.
One of these limits is visible in the KVM_IRQ_LINE ioctl, which
only allows 256 vcpus to be signalled when using the CPU or PPI
types. Unfortunately, we've cornered ourselves badly by allocating
all the bits in the irq field.
Since the irq_type subfield (8 bit wide) is currently only taking
the values 0, 1 and 2 (and we have been careful not to allow anything
else), let's reduce this field to only 4 bits, and allocate the
remaining 4 bits to a vcpu2_index, which acts as a multiplier:
vcpu_id = 256 * vcpu2_index + vcpu_index
With that, and a new capability (KVM_CAP_ARM_IRQ_LINE_LAYOUT_2)
allowing this to be discovered, it becomes possible to inject
PPIs to up to 4096 vcpus. But please just don't.
Whilst we're there, add a clarification about the use of KVM_IRQ_LINE
on arm, which is not completely conditionned by KVM_CAP_IRQCHIP.
Reported-by: Zenghui Yu <yuzenghui@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Since commit 1137ceee76 ("ARM: OMAP1: ams-delta: Don't request unused
GPIOs"), on-board audio has appeared muted. It has been discovered that
believed to be unused GPIO pins "hookflash1" and "hookflash2" need to be
set low for audible sound in handsfree and handset mode respectively.
According to Amstrad E3 wiki, the purpose of both pins hasn't been
clearly identified. Original Amstrad software used to produce a high
pulse on them when the phone was taken off hook or recall was pressed.
With the current findings, we can assume the pins provide a kind of
audio mute function, separately for handset and handsfree operation
modes.
Commit 2afdb4c41d ("ARM: OMAP1: ams-delta: Fix audio permanently
muted") attempted to fix the issue temporarily by hogging the GPIO pin
"hookflash1" renamed to "audio_mute", however the fix occurred
incomplete as it restored audible sound only for handsfree mode.
Stop hogging that pin, rename the pins to "handsfree_mute" and
"handset_mute" respectively and implement appropriate DAPM event
callbacks for "Speaker" and "Earpiece" DAPM widgets.
Fixes: 1137ceee76 ("ARM: OMAP1: ams-delta: Don't request unused GPIOs")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20190907111650.15440-1-jmkrzyszt@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of relying on the CTS template to wrap the accelerated CBC
skcipher, implement the ciphertext stealing part directly.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Update the AES-XTS implementation based on NEON instructions so that it
can deal with inputs whose size is not a multiple of the cipher block
size. This is part of the original XTS specification, but was never
implemented before in the Linux kernel.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Update the AES-XTS implementation based on AES instructions so that it
can deal with inputs whose size is not a multiple of the cipher block
size. This is part of the original XTS specification, but was never
implemented before in the Linux kernel.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Replace the vector load from memory sequence with a simple instruction
sequence to compose the tweak vector directly.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Replace the vector load from memory sequence with a simple instruction
sequence to compose the tweak vector directly.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When the ARM AES instruction based crypto driver was introduced, there
were no known implementations that could benefit from a 4-way interleave,
and so a 3-way interleave was used instead. Since we have sufficient
space in the SIMD register file, let's switch to a 4-way interleave to
align with the 64-bit driver, and to ensure that we can reach optimum
performance when running under emulation on high end 64-bit cores.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reduce the scope of the kernel_neon_begin/end regions so that the SIMD
unit is released (and thus preemption re-enabled) if the crypto operation
cannot be completed in a single scatterwalk step. This avoids scheduling
blackouts due to preemption being enabled for unbounded periods, resulting
in a more responsive system.
After this change, we can also permit the cipher_walk infrastructure to
sleep, so set the 'atomic' parameter to skcipher_walk_virt() to false as
well.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The AES round keys are arrays of u32s in native endianness now, so
update the function prototypes accordingly.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This is a fairly complete description of an OLPC XO 1.75 laptop.
What's missing for now is the GPU, LCD controller, DCON, the panel and
audio.
The machine is booted with OpenFirmware and thus has a devicetree.
However, older versions are unable to create a valid FDT and don't
follow the Linux bindings. Having an device tree in the kernel tree
makes it easier to use mainline kernels on such machines, test changes
with CONFIG_ARM_APPENDED_DTB and give a good reference on what bindings
are used on the machine without an access to one.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
This device is not an OTG phy, it's a regular USB HS phy. Follow the
generic node name recommendation, and rename it to "usb-phy".
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
This makes the 8250_of driver happy. There are two more drivers in the
tree that bind to mrvl,mmp-uart compatibles: pxa and 8250_pxa and
neither of them requires the reg-shift property, assuming it's always 2.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
The SPI bus has a single address cell and not size cells.
Also, dtc thinks the SPI nodes are preferrably called "spi" and it is
right to think so.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
When the pinmux configuration was added, it was accidentally placed into
the omap3_pmx_wkup node when it should have been placed into the
omap3_pmx_core. This error was accidentally propagated to stable by
me when I blindly requested the pull after seeing I2C issues without
actually reviewing the content of the pinout. Since the bootloader
previously muxed these correctly in the past, was a hidden error.
This patch moves the i2c2_pins and i2c3_pins to the correct node
which should eliminate i2c bus errors and timeouts due to the fact
the bootloader uses the save device tree that no longer properly
assigns these pins.
Fixes: 5fe3c0fa0d ("ARM: dts: Add pinmuxing for i2c2 and i2c3
for LogicPD SOM-LV") #4.9+
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The calculation of memblock_limit in adjust_lowmem_bounds() assumes that
bank 0 starts from a PMD-aligned address. However, the beginning of the
first bank may be NOMAP memory and the start of usable memory
will be not aligned to PMD boundary. In such case the memblock_limit will
be set to the end of the NOMAP region, which will prevent any memblock
allocations.
Mark the region between the end of the NOMAP area and the next PMD-aligned
address as NOMAP as well, so that the usable memory will start at
PMD-aligned address.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
A previous commit removed the panel-dpi driver, which made the
video on the AM3517-evm stop working because it relied on the dpi
driver for setting video timings. Now that the simple-panel driver
is available in omap2plus, this patch migrates the am3517-evm
to use a similar panel and remove the manual timing requirements.
Fixes: 8bf4b16211 ("drm/omap: Remove panel-dpi driver")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A previous commit removed the panel-dpi driver, which made the
Torpedo video stop working because it relied on the dpi driver
for setting video timings. Now that the simple-panel driver is
available in omap2plus, this patch migrates the Torpedo dev kits
to use a similar panel and remove the manual timing requirements.
Fixes: 8bf4b16211 ("drm/omap: Remove panel-dpi driver")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When the panel-dpi driver was removed, the simple-panels driver
was never enabled, so anyone who used the panel-dpi driver lost
video, and those who used it inconjunction with simple-panels
would have to manually enable CONFIG_DRM_PANEL_SIMPLE.
This patch makes CONFIG_DRM_PANEL_SIMPLE a module in the same
way the deprecated panel-dpi was.
Fixes: 8bf4b16211 ("drm/omap: Remove panel-dpi driver")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull irqchip updates for Linux 5.4 from Marc Zyngier:
- Large GICv3 updates to support new PPI and SPI ranges
- Conver all alloc_fwnode() users to use PAs instead of VAs
- Add support for Marvell's MMP3 irqchip
- Add support for Amlogic Meson SM1
- Various cleanups and fixes
We can currently get "Unable to handle kernel paging request at
virtual address" for invalid clocks with dts node but no driver:
(__clk_get_hw) from [<c0138ebc>] (ti_sysc_find_one_clockdomain+0x18/0x34)
(ti_sysc_find_one_clockdomain) from [<c0138f0c>] (ti_sysc_clkdm_init+0x34/0xdc)
(ti_sysc_clkdm_init) from [<c0584660>] (sysc_probe+0xa50/0x10e8)
(sysc_probe) from [<c065c6ac>] (platform_drv_probe+0x58/0xa8)
Let's add IS_ERR checks to ti_sysc_clkdm_init() as And let's start treating
clk_get() with -ENOENT as a proper error. If the clock name is specified
in device tree we must succeed with clk_get() to continue. For modules with
no clock names specified in device tree we will just ignore the clocks.
Fixes: 2b2f7def05 ("bus: ti-sysc: Add support for missing clockdomain handling")
Acked-by: Roger Quadros <rogerq@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Removal of the rk3288-fennec board which never made it to
any market.
* tag 'v5.4-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
dt-bindings: arm: rockchip: remove reference to fennec board
ARM: dts: rockchip: remove rk3288 fennec board support
Link: https://lore.kernel.org/r/1718334.9BoTfW0Ujv@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
