The rk3328 uses a dw-hdmi controller with an external hdmi phy from
Innosilicon which uses the generic phy framework for access.
Add the necessary data and the compatible for the rk3328 to the
rockchip dw-hdmi driver.
changes in v5:
- disable CEC_5V option to make CEC actually work (Jonas)
changes in v3:
- reword as suggested by Rob to show that it's a dw-hdmi + Inno phy
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Zheng Yang <zhengyang@rock-chips.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180912124740.20343-7-heiko@sntech.de
Initial introduction of Facebook TiogaPass family equipped with
Aspeed 2500 BMC SoC. TiogaPass is a x86 server development kit
with a ASPEED ast2500 BMC manufactured by Facebook.
This adds an entry of Facebook in Documentation for vendor prefix
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
This panel is marketed as Banana Pi 7" LCD display. On the back is
a sticker denoting the model name S070WV20-CT16.
This is a 7" 800x480 panel connected through a 24-bit RGB interface.
However the panel only does 262k colors.
Depending on the variant, the PCB attached to the panel module either
supports DSI, or DSI + 24-bit RGB. DSI is converted to 24-bit RGB via
an onboard ICN6211 MIPI DSI - RGB bridge chip, then fed to the panel
itself.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180907041948.19913-5-wens@csie.org
The AS370 SoC is a new derivative of the berlin family. However, the
SoC isn't named as berlin*.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Move berlin binding documentation as part of transition from Marvell
berlin to Synaptics SoC.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Rob Herring <robh@kernel.org>
There should not be a comma in the address used for the instance
so drop them.
This is a left over from a review of the final version before
Herbert Xu picked the series up.
Reported-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fixes: 8f026dc887fe ("dt-bindings: Add bidnings for Hisilicon SEC crypto accelerators")
Signed-off-by: Rob Herring <robh@kernel.org>
Documentation/devicetree/bindings/fpga/fpga-region.txt has an error
regarding the freeze controller bridge, secifically:
compatible = "altr,freeze-bridge";
The compatibility string should be "altr,freeze-bridge-controller"
as set forth in altera-freeze-bridge.txt.
Signed-off-by: Alan Tull <atull@kernel.org>
Reported-by: Dalon Westergreen <dalon.westergreen@intel.com>
Acked-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
The i.MX7 SRC's compatible string should be "fsl,imx7d-src".
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The unit of dynamic-power-coefficient is described as mW/MHz/uV^2 whereas
its usage in the code assumes that unit is uW/MHz/V^2
In drivers/thermal/cpu_cooling.c, the code is :
power = (u64)capacitance * freq_mhz * voltage_mv * voltage_mv;
do_div(power, 1000000000);
which can be summarized as :
power (mW) = capacitance * freq_mhz/1000 * (voltage_mv/1000)^2
or
power (mW) = (capacitance * freq_mhz * (voltage_mv/1000)^2) / 1000
then
power (mW) = power (uW) / 1000
so
power (uW) = capacitance * freq_mhz * (voltage_mv/1000)^2
Furthermore, if we test basic values like :
voltage_mv = 1000mV = 1V
freq_mhz = 1000Mhz
The minimum possible power, when dynamic-power-coefficient equals 1, will
be with current unit:
min power = 1 * 1000 * (1000000)^2 = 10^15 mW
which is not realistic
With the unit used by the code, the min power is
min power = 1 * 1000 * 1^2 = 1000uW = 1mW which is far more realistic
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Acked-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
arm64: zynqmp: SoC changes for v4.20
- Adding firmware API for SoC with debugfs interface
Firmware driver communicates to Platform Management Unit (PMU) by using
SMC instructions routed to Arm Trusted Firmware (ATF). Initial version
adds support for base firmware driver with query and clock APIs.
EEMI spec is available here:
https://www.xilinx.com/support/documentation/user_guides/ug1200-eemi-api.pdf
* tag 'zynqmp-soc-for-v4.20-v2' of https://github.com/Xilinx/linux-xlnx:
firmware: xilinx: Add debugfs for query data API
firmware: xilinx: Add debugfs interface
firmware: xilinx: Add clock APIs
firmware: xilinx: Add query data API
firmware: xilinx: Add Zynqmp firmware driver
dt-bindings: firmware: Add bindings for ZynqMP firmware
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add an evaluation board device tree more in-line with all our other
device trees.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Simplify model and compatible by dropping the 256/512 MB from the model,
-512 from the compatible and rename that property from toradex,iris to
toradex,colibri_t20-iris to be more in-line with all our other device
trees.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Simplify model and compatible by dropping the 256/512 MB from the model
and -512 from the compatible properties to be more in-line with all our
other device trees.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Support the V1.1 hardware revisions with the following change:
Changed power rail for MMC1 interface to a 3.3V/1.8V switchable rail in
order to be able to run UHS SD cards in ultra high speed 1.8V mode.
[ 207.502011] mmc2: host does not support reading read-only switch,
assuming write-enable
[ 207.517011] mmc2: new ultra high speed SDR104 SDHC card at address
aaaa
[ 207.534190] mmcblk2: mmc2:aaaa SE32G 29.7 GiB
[ 207.545096] mmcblk2: p1
root@apalis-t30:~# cat /sys/kernel/debug/mmc2/ios
clock: 208000000 Hz
actual clock: 204000000 Hz
vdd: 21 (3.3 ~ 3.4 V)
bus mode: 2 (push-pull)
chip select: 0 (don't care)
power mode: 2 (on)
bus width: 2 (4 bits)
timing spec: 6 (sd uhs SDR104)
signal voltage: 1 (1.80 V)
driver type: 0 (driver type B)
root@apalis-t30:~# hdparm -t /dev/mmcblk2
/dev/mmcblk2:
Timing buffered disk reads: 256 MB in 3.02 seconds = 84.71 MB/sec
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
PLX Technology meanwhile got bought by Broadcom Corporation but the
vendor prefix plx is still used in 8 current device trees. This silences
the following checkpatch.pl warning:
WARNING: DT compatible string vendor "plx" appears un-documented
-- check ./Documentation/devicetree/bindings/vendor-prefixes.txt
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the actual dts for the tinker board S, which brings its own emmc
device, not therefore not requiring an sd-card to boot.
Signed-off-by: David Summers <beagleboard@davidjohnsummers.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Rockpro64 is a rockchip RK3399 based board from pine64.org.
This patch adds basic device node support for Rockpro64 board and make it able
to bring up.
Peripheral Works
- Sdcard
- USB 2.0, 3.0
- Leds
- Ethernet
- Debug console
Not working:
- USB Type-C
Signed-off-by: Akash Gajjar <Akash_Gajjar@mentor.com>
Acked-by: Deepak Das <Deepak_Das@mentor.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add documentation to describe Xilinx ZynqMP firmware driver
bindings. Firmware driver provides an interface to firmware
APIs. Interface APIs can be used by any driver to communicate
to PMUFW (Platform Management Unit).
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
soc: driver soc update for v4.20
- Enable host-id as an optional dt property
- Fix minor typo in knav driver
* tag 'drivers_soc_for_4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
soc: ti: fix spelling mistake "instace" -> "instance"
firmware: ti_sci: Provide host-id as an optional dt parameter
Documentation: dt: keystone: ti-sci: Add optional host-id parameter
Signed-off-by: Olof Johansson <olof@lixom.net>
The coresight drivers relied on default bindings for graph
in DT, while reusing the "reg" field of the "ports" to indicate
the actual hardware port number for the connections. This can
cause duplicate ports with same addresses, but different
direction. However, with the rules getting stricter for the
address mismatch with the label, it is no longer possible to use
the port address field for the hardware port number.
This patch introduces new DT binding rules for coresight
components, based on the same generic DT graph bindings, but
avoiding the address duplication.
- All output ports must be specified under a child node with
name "out-ports".
- All input ports must be specified under a childe node with
name "in-ports".
- Port address should match the hardware port number.
The support for legacy bindings is retained, with a warning.
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the bindings for maxim max98088/9 audio codec.
Signed-off-by: Andreas Färber <afaerber@suse.de>
[m.felsch@pengutronix.de: adapt commit message]
[m.felsch@pengutronix.de: adapt formatting]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Update the compatible string for UFS QMP PHY on SDM845.
Signed-off-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds a new optional property "renesas,no-otg-pins" which
a board does not provide proper otg pins.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Document the compatible string "brcm,bcm63138-sata-phy" as a valid
compatible string describing the standard Broadcom SATA PHY block.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add DT bindings for PHY interface built into PCIe controller implemented
in UniPhier SoCs.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
