imx25 did not work without a firmware previously.
This patch adds a DT compatible to pass the correct data with the
default script addresses for imx25.
Add imx25 compatible to the list of compatibles in the binding
documentation.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add Freescale enhanced direct memory(eDMA) controller support.
This module can be found on Vybrid and LS-1 SoCs.
Signed-off-by: Alison Wang <b18965@freescale.com>
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Document the required "clocks" phandles and their corresponding
"clock-names" properties for the two clocks used by the GENET hardware
block ("enet" and "enet-wol").
CC: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Freescale DSPI module will have two endianess in different platform,
but ARM is little endian. So when DSPI in big endian, core in little endian,
readl and writel can not adjust R/W register in this condition.
This patch will remove general readl/writel, and import regmap mechanism.
Data endian will be transfered in regmap APIs.
Documents: dspi add bool "big-endian" in dts node if DSPI module
work in big endian.
Signed-off-by: Chao Fu <b44548@freescale.com>
Reviewed-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Pull ARM SoC fixes from Kevin Hilman:
"A collection of ARM SoC fixes for v3.14-rc1.
Mostly a collection of Kconfig, device tree data and compilation fixes
along with fix to drivers/phy that fixes a boot regression on some
Marvell mvebu platforms"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
dma: mv_xor: Silence a bunch of LPAE-related warnings
ARM: ux500: disable msp2 device tree node
ARM: zynq: Reserve not DMAable space in front of the kernel
ARM: multi_v7_defconfig: Select CONFIG_SOC_DRA7XX
ARM: imx6: Initialize low-power mode early again
ARM: pxa: fix various compilation problems
ARM: pxa: fix compilation problem on AM300EPD board
ARM: at91: add Atmel's SAMA5D3 Xplained board
spi/atmel: document clock properties
mmc: atmel-mci: document clock properties
ARM: at91: enable USB host on at91sam9n12ek board
ARM: at91/dt: fix sama5d3 ohci hclk clock reference
ARM: at91/dt: sam9263: fix compatibility string for the I2C
ata: sata_mv: Fix probe failures with optional phys
drivers: phy: Add support for optional phys
drivers: phy: Make NULL a valid phy reference
ARM: fix HAVE_ARM_TWD selection for OMAP and shmobile
ARM: moxart: move DMA_OF selection to driver
ARM: hisi: fix kconfig warning on HAVE_ARM_TWD
This brings the xhci-platform bindings in sync with what we've done for
the ohci- and ehci-platform drivers. As discussed there using platform as a
postfix is a bit weird as the platform bus is a Linux specific thing and
the bindings are supposed to be OS agnostic.
Note that the old xhci-platform compatible string is kept around for, well,
compatibility reasons.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This brings the uhci-platform bindings in sync with what we've done for
the ohci- and ehci-platform drivers. As discussed there using platform as a
prefix is a bit weird as the platform bus is a Linux specific thing and
the bindings are supposed to be OS agnostic.
Note that the old platform-uhci compatible string is kept around for, well,
compatibility reasons.
While at it rename the bindings txt file to match the name of all the
other ?hci-platform bindings docs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clock names mistakenly given opposite. This patch fix this issue.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Allwinner A10 compatibles were following a slightly different compatible
patterns than the rest of the SoCs for historical reasons. Change the compatibles
to match the other pattern in the SID driver for consistency.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds a simple ASoC board driver fo the Armada 370
Development Board, which connects the audio unit of the Armada 370 SoC
to the I2C-based CS42L51.
For now, only the analog audio input and output through the CS42L51
are supported, but a followup patch adds S/PDIF support to this
driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Update the compatible string for Overo/Tobi to reflect the latest
changes.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds the Device Tree bindings for the Broadcom GENET Gigabit
Ethernet controller. A bunch of examples are provided to illustrate the
versatile aspect of the hardare.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
linux-can-next-for-3.15-20140212
Marc Kleine-Budde says:
====================
this is a pull request of eight patches for net-next/master.
Florian Vaussard contributed a series that merged the sja1000 of_platform
into the platform driver. The of_platform driver is finally removed.
Stephane Grosjean supplied a patch to allocate CANFD skbs. In a patch
by Uwe Kleine-König another missing copyright information was added to
a userspace header. And a patch by Yoann DI RUZZA that adds listen only
mode to the at91_can driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
STi series SOCs have a glue layer on top of the synopsis gmac IP, this
glue layer needs to be configured before the gmac driver starts using
the IP.
This patch adds a support to this glue layer which is configured via
stmmac setup, init, exit callbacks.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the devicetree documentation for the Maxim MAX310X UARTs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This atomic commit changes the Integrator clock implementation
and the machines to register clocks from the device tree and
use these instead of the previous hard-coded clocks.
In the clock implementation all hard-coded clocks and the
special initialization function call goes away, and is
replaced by two compatible strings for the two clocks
available on the core module.
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the option to choose clock on which pin input to SSC (as slave).
Default is on TK pin to SSC, add "atmel,clk-from-rk-pin" option to
specify the clock is on RK pin to SSC.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For most platforms, the CPU and ESAI device is in the same endianess
mode. While for the LS1 platform, the CPU is in LE mode and the ESAI
is in BE mode.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For most platforms, the CPU and SPDIF device is in the same endianess
mode. While for the LS1 platform, the CPU is in LE mode and the SPDIF
is in BE mode.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Jonathan writes:
First set of new drivers and cleanups for IIO in the 3.15 cycle.
New drivers:
* si7005 relative humidity and temperature sensor
* Lite-on ltr501 ambient light and proximity sensor
Cleanups
* Clean up some dead comments in max1363
* Drop some obsolete variables in adjd_s311 and tcs3472 left over from
the introduction of iio_push_to_buffers_with_timestamp.
* Drop some unneeded linux/init.h includes
* Squish a sparse warning in mpl3115 by correctly specifying a be32 variable.
* A number of cleanups and fixes for sca3000
* Drop an unneed checks in mxs-lradc, ad7303 and adis16400.
* Drop a platform_set_drvdata in viperboard after the only use of it was
removed during a devm conversion.
* Add a missing device name for ak8975 to comply with the ABI.
* Put mpu6050 into the IMU menu as it slipped out into the main menu.
* Fix a typo and some comment formatting in mpu6050.
* Document at91 ADC clock properties.
The initial versions of the devicetree enablement patches for ehci-platform
used "ehci-platform" as compatible string. However this was disliked by various
reviewers because the platform bus is a Linux invention and devicetree is
supposed to be OS agnostic. After much discussion I gave up, added a:
"depends on !PPC_OF" to Kconfig to avoid a known conflict with PPC-OF platforms
and went with the generic usb-ehci as requested.
In retro-spect I should have chosen something different, the dts files for many
existing boards already claim to be compatible with "usb-ehci", ie they have:
compatible = "ti,ehci-omap", "usb-ehci";
In theory this should not be a problem since the "ti,ehci-omap" entry takes
presedence, but in practice using a conflicting compatible string is an issue,
because it makes which driver gets used depend on driver registration order.
This patch changes the compatible string claimed by ehci-platform to
"generic-ehci", avoiding the driver registration / module loading ordering
problems, and removes the "depends on !PPC_OF" workaround.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The initial versions of the devicetree enablement patches for ohci-platform
used "ohci-platform" as compatible string. However this was disliked by various
reviewers because the platform bus is a Linux invention and devicetree is
supposed to be OS agnostic. After much discussion I gave up and went with
the generic usb-ohci as requested.
In retro-spect I should have chosen something different, the dts files for many
existing boards already claim to be compatible with "usb-ohci", ie they have:
compatible = "ti,ohci-omap3", "usb-ohci";
In theory this should not be a problem since the "ti,ohci-omap3" entry takes
presedence, but in practice using a conflicting compatible string is an issue,
because it makes which driver gets used depend on driver registration order.
This patch changes the compatible string claimed by ohci-platform to
"generic-ohci", avoiding the driver registration / module loading ordering
problems.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Scorpion and Krait don't use the spin-table enable-method.
Instead they rely on mmio register accesses to enable power and
clocks to bring CPUs out of reset. Document their enable-methods.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Rohit Vaswani <rvaswani@codeaurora.org>
[sboyd: Split off into separate patch, renamed methods to
match compatible nodes]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Pull DeviceTree fixes from Rob Herring:
- Fix compile error drivers/spi/spi-rspi.c with !CONFIG_OF
- Fix warnings for unused/uninitialized variables with !CONFIG_OF
- Fix PCIe bus matching for powerpc
- Add documentation for various vendor strings
* tag 'dt-fixes-for-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
DT: Add vendor prefix for Spansion Inc.
of/device: Nullify match table in of_match_device() for CONFIG_OF=n
dt-bindings: add vendor-prefix for neonode
of: fix PCI bus match for PCIe slots
of: restructure for_each macros to fix compile warnings
of: add vendor prefix for Honeywell
of: Update qcom vendor prefix description
of: add vendor prefix for Allwinner Technology
Pull networking updates from David Miller:
1) Fix flexcan build on big endian, from Arnd Bergmann
2) Correctly attach cpsw to GPIO bitbang MDIO drive, from Stefan Roese
3) udp_add_offload has to use GFP_ATOMIC since it can be invoked from
non-sleepable contexts. From Or Gerlitz
4) vxlan_gro_receive() does not iterate over all possible flows
properly, fix also from Or Gerlitz
5) CAN core doesn't use a proper SKB destructor when it hooks up
sockets to SKBs. Fix from Oliver Hartkopp
6) ip_tunnel_xmit() can use an uninitialized route pointer, fix from
Eric Dumazet
7) Fix address family assignment in IPVS, from Michal Kubecek
8) Fix ath9k build on ARM, from Sujith Manoharan
9) Make sure fail_over_mac only applies for the correct bonding modes,
from Ding Tianhong
10) The udp offload code doesn't use RCU correctly, from Shlomo Pongratz
11) Handle gigabit features properly in generic PHY code, from Florian
Fainelli
12) Don't blindly invoke link operations in
rtnl_link_get_slave_info_data_size, they are optional. Fix from
Fernando Luis Vazquez Cao
13) Add USB IDs for Netgear Aircard 340U, from Bjørn Mork
14) Handle netlink packet padding properly in openvswitch, from Thomas
Graf
15) Fix oops when deleting chains in nf_tables, from Patrick McHardy
16) Fix RX stalls in xen-netback driver, from Zoltan Kiss
17) Fix deadlock in mac80211 stack, from Emmanuel Grumbach
18) inet_nlmsg_size() forgets to consider ifa_cacheinfo, fix from Geert
Uytterhoeven
19) tg3_change_mtu() can deadlock, fix from Nithin Sujir
20) Fix regression in setting SCTP local source addresses on accepted
sockets, caused by some generic ipv6 socket changes. Fix from
Matija Glavinic Pecotic
21) IPPROTO_* must be pure defines, otherwise module aliases don't get
constructed properly. Fix from Jan Moskyto
22) IPV6 netconsole setup doesn't work properly unless an explicit
source address is specified, fix from Sabrina Dubroca
23) Use __GFP_NORETRY for high order skb page allocations in
sock_alloc_send_pskb and skb_page_frag_refill. From Eric Dumazet
24) Fix a regression added in netconsole over bridging, from Cong Wang
25) TCP uses an artificial offset of 1ms for SRTT, but this doesn't jive
well with TCP pacing which needs the SRTT to be accurate. Fix from
Eric Dumazet
26) Several cases of missing header file includes from Rashika Kheria
27) Add ZTE MF667 device ID to qmi_wwan driver, from Raymond Wanyoike
28) TCP Small Queues doesn't handle nonagle properly in some corner
cases, fix from Eric Dumazet
29) Remove extraneous read_unlock in bond_enslave, whoops. From Ding
Tianhong
30) Fix 9p trans_virtio handling of vmalloc buffers, from Richard Yao
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (136 commits)
6lowpan: fix lockdep splats
alx: add missing stats_lock spinlock init
9p/trans_virtio.c: Fix broken zero-copy on vmalloc() buffers
bonding: remove unwanted bond lock for enslave processing
USB2NET : SR9800 : One chip USB2.0 USB2NET SR9800 Device Driver Support
tcp: tsq: fix nonagle handling
bridge: Prevent possible race condition in br_fdb_change_mac_address
bridge: Properly check if local fdb entry can be deleted when deleting vlan
bridge: Properly check if local fdb entry can be deleted in br_fdb_delete_by_port
bridge: Properly check if local fdb entry can be deleted in br_fdb_change_mac_address
bridge: Fix the way to check if a local fdb entry can be deleted
bridge: Change local fdb entries whenever mac address of bridge device changes
bridge: Fix the way to find old local fdb entries in br_fdb_change_mac_address
bridge: Fix the way to insert new local fdb entries in br_fdb_changeaddr
bridge: Fix the way to find old local fdb entries in br_fdb_changeaddr
tcp: correct code comment stating 3 min timeout for FIN_WAIT2, we only do 1 min
net: vxge: Remove unused device pointer
net: qmi_wwan: add ZTE MF667
3c59x: Remove unused pointer in vortex_eisa_cleanup()
net: fix 'ip rule' iif/oif device rename
...
This patch replaces custom lcd_power() callback with
regulator API over LCD class.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The audio unit found in the Armada 370 SoC is similar to the one used
in the Marvell Kirkwood and Marvell Dove SoCs. Therefore, this commit
allows the Kirkwood audio driver to be built on mvebu platforms, and
adds an additional compatible string to identify the Armada 370
variant of the audio unit.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This commit adds a trivial Device Tree binding to the I2C-based
cs42l51 sound codec, so that it can be used from Device Tree based
platforms.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some of the 00-INDEX files are somewhat outdated and some folders does
not contain 00-INDEX at all. Only outdated (with the notably exception
of spi) indexes are touched here, the 169 folders without 00-INDEX has
not been touched.
New 00-INDEX
- spi/* was added in a series of commits dating back to 2006
Added files (missing in (*/)00-INDEX)
- dmatest.txt was added by commit 851b7e16a0 ("dmatest: run test via
debugfs")
- this_cpu_ops.txt was added by commit a1b2a555d6 ("percpu: add
documentation on this_cpu operations")
- ww-mutex-design.txt was added by commit 040a0a3710 ("mutex: Add
support for wound/wait style locks")
- bcache.txt was added by commit cafe563591 ("bcache: A block layer
cache")
- kernel-per-CPU-kthreads.txt was added by commit 49717cb404
("kthread: Document ways of reducing OS jitter due to per-CPU
kthreads")
- phy.txt was added by commit ff76496347 ("drivers: phy: add generic
PHY framework")
- block/null_blk was added by commit 12f8f4fc03 ("null_blk:
documentation")
- module-signing.txt was added by commit 3cafea3076 ("Add
Documentation/module-signing.txt file")
- assoc_array.txt was added by commit 3cb989501c ("Add a generic
associative array implementation.")
- arm/IXP4xx was part of the initial repo
- arm/cluster-pm-race-avoidance.txt was added by commit 7fe31d28e8
("ARM: mcpm: introduce helpers for platform coherency exit/setup")
- arm/firmware.txt was added by commit 7366b92a77 ("ARM: Add
interface for registering and calling firmware-specific operations")
- arm/kernel_mode_neon.txt was added by commit 2afd0a0524 ("ARM:
7825/1: document the use of NEON in kernel mode")
- arm/tcm.txt was added by commit bc581770cf ("ARM: 5580/2: ARM TCM
(Tightly-Coupled Memory) support v3")
- arm/vlocks.txt was added by commit 9762f12d3e ("ARM: mcpm: Add
baremetal voting mutexes")
- blackfin/gptimers-example.c, Makefile was added by commit
4b60779d5e ("Blackfin: add an example showing how to use the
gptimers API")
- devicetree/usage-model.txt was added by commit 31134efc68 ("dt:
Linux DT usage model documentation")
- fb/api.txt was added by commit fb21c2f428 ("fbdev: Add FOURCC-based
format configuration API")
- fb/sm501.txt was added by commit e6a0498071 ("video, sm501: add
edid and commandline support")
- fb/udlfb.txt was added by commit 96f8d864af ("fbdev: move udlfb out
of staging.")
- filesystems/Makefile was added by commit 1e0051ae48
("Documentation/fs/: split txt and source files")
- filesystems/nfs/nfsd-admin-interfaces.txt was added by commit
8a4c6e19cf ("nfsd: document kernel interfaces for nfsd
configuration")
- ide/warm-plug-howto.txt was added by commit f74c91413e ("ide: add
warm-plug support for IDE devices (take 2)")
- laptops/Makefile was added by commit d49129accc
("Documentation/laptop/: split txt and source files")
- leds/leds-blinkm.txt was added by commit b54cf35a7f ("LEDS: add
BlinkM RGB LED driver, documentation and update MAINTAINERS")
- leds/ledtrig-oneshot.txt was added by commit 5e417281cd ("leds: add
oneshot trigger")
- leds/ledtrig-transient.txt was added by commit 44e1e9f8e7 ("leds:
add new transient trigger for one shot timer activation")
- m68k/README.buddha was part of the initial repo
- networking/LICENSE.(qla3xxx|qlcnic|qlge) was added by commits
40839129f7, c4e84bde1d, 5a4faa8737
- networking/Makefile was added by commit 3794f3e812 ("docsrc: build
Documentation/ sources")
- networking/i40evf.txt was added by commit 105bf2fe6b ("i40evf: add
driver to kernel build system")
- networking/ipsec.txt was added by commit b3c6efbc36 ("xfrm: Add
file to document IPsec corner case")
- networking/mac80211-auth-assoc-deauth.txt was added by commit
3cd7920a2b ("mac80211: add auth/assoc/deauth flow diagram")
- networking/netlink_mmap.txt was added by commit 5683264c39
("netlink: add documentation for memory mapped I/O")
- networking/nf_conntrack-sysctl.txt was added by commit c9f9e0e159
("netfilter: doc: add nf_conntrack sysctl api documentation") lan)
- networking/team.txt was added by commit 3d249d4ca7 ("net: introduce
ethernet teaming device")
- networking/vxlan.txt was added by commit d342894c5d ("vxlan:
virtual extensible lan")
- power/runtime_pm.txt was added by commit 5e928f77a0 ("PM: Introduce
core framework for run-time PM of I/O devices (rev. 17)")
- power/charger-manager.txt was added by commit 3bb3dbbd56
("power_supply: Add initial Charger-Manager driver")
- RCU/lockdep-splat.txt was added by commit d7bd2d68aa ("rcu:
Document interpretation of RCU-lockdep splats")
- s390/kvm.txt was added by 5ecee4b (KVM: s390: API documentation)
- s390/qeth.txt was added by commit b4d72c08b3 ("qeth: bridgeport
support - basic control")
- scheduler/sched-bwc.txt was added by commit 88ebc08ea9 ("sched: Add
documentation for bandwidth control")
- scsi/advansys.txt was added by commit 4bd6d7f356 ("[SCSI] advansys:
Move documentation to Documentation/scsi")
- scsi/bfa.txt was added by commit 1ec90174bd ("[SCSI] bfa: add
readme file")
- scsi/bnx2fc.txt was added by commit 12b8fc10ea ("[SCSI] bnx2fc: Add
driver documentation")
- scsi/cxgb3i.txt was added by commit c3673464eb ("[SCSI] cxgb3i: Add
cxgb3i iSCSI driver.")
- scsi/hpsa.txt was added by commit 992ebcf14f ("[SCSI] hpsa: Add
hpsa.txt to Documentation/scsi")
- scsi/link_power_management_policy.txt was added by commit
ca77329fb7 ("[libata] Link power management infrastructure")
- scsi/osd.txt was added by commit 78e0c621de ("[SCSI] osd:
Documentation for OSD library")
- scsi/scsi-parameter.txt was created/moved by commit 163475fb11
("Documentation: move SCSI parameters to their own text file")
- serial/driver was part of the initial repo
- serial/n_gsm.txt was added by commit 323e84122e ("n_gsm: add a
documentation")
- timers/Makefile was added by commit 3794f3e812 ("docsrc: build
Documentation/ sources")
- virt/kvm/s390.txt was added by commit d9101fca3d ("KVM: s390:
diagnose call documentation")
- vm/split_page_table_lock was added by commit 49076ec2cc ("mm:
dynamically allocate page->ptl if it cannot be embedded to struct
page")
- w1/slaves/w1_ds28e04 was added by commit fbf7f7b4e2 ("w1: Add
1-wire slave device driver for DS28E04-100")
- w1/masters/omap-hdq was added by commit e0a29382c6 ("hdq:
documentation for OMAP HDQ")
- x86/early-microcode.txt was added by commit 0d91ea86a8 ("x86, doc:
Documentation for early microcode loading")
- x86/earlyprintk.txt was added by commit a1aade4788 ("x86/doc:
mini-howto for using earlyprintk=dbgp")
- x86/entry_64.txt was added by commit 8b4777a4b5 ("x86-64: Document
some of entry_64.S")
- x86/pat.txt was added by commit d27554d874 ("x86: PAT
documentation")
Moved files
- arm/kernel_user_helpers.txt was moved out of arch/arm/kernel by
commit 37b8304642 ("ARM: kuser: move interface documentation out of
the source code")
- efi-stub.txt was moved out of x86/ and down into Documentation/ in
commit 4172fe2f8a ("EFI stub documentation updates")
- laptops/hpfall.c was moved out of hwmon/ and into laptops/ in commit
efcfed9bad ("Move hp_accel to drivers/platform/x86")
- commit 5616c23ad9 ("x86: doc: move x86-generic documentation from
Doc/x86/i386"):
* x86/usb-legacy-support.txt
* x86/boot.txt
* x86/zero_page.txt
- power/video_extension.txt was moved to acpi in commit 70e66e4df1
("ACPI / video: move video_extension.txt to Documentation/acpi")
Removed files (left in 00-INDEX)
- memory.txt was removed by commit 00ea8990aa ("memory.txt: remove
stray information")
- gpio.txt was moved to gpio/ in commit fd8e198cfc ("Documentation:
gpiolib: document new interface")
- networking/DLINK.txt was removed by commit 168e06ae26
("drivers/net: delete old parallel port de600/de620 drivers")
- serial/hayes-esp.txt was removed by commit f53a2ade0b ("tty: esp:
remove broken driver")
- s390/TAPE was removed by commit 9e280f6693 ("[S390] remove tape
block docu")
- vm/locking was removed by commit 57ea8171d2 ("mm: documentation:
remove hopelessly out-of-date locking doc")
- laptops/acer-wmi.txt was remvoed by commit 020036678e ("acer-wmi:
Delete out-of-date documentation")
Typos/misc issues
- rpc-server-gss.txt was added as knfsd-rpcgss.txt in commit
030d794bf4 ("SUNRPC: Use gssproxy upcall for server RPCGSS
authentication.")
- commit b88cf73d92 ("net: add missing entries to
Documentation/networking/00-INDEX")
* generic-hdlc.txt was added as generic_hdlc.txt
* spider_net.txt was added as spider-net.txt
- w1/master/mxc-w1 was added as mxc_w1 by commit a5fd9139f7 ("w1: add
1-wire master driver for i.MX27 / i.MX31")
- s390/zfcpdump.txt was added as zfcpdump by commit 6920c12a40
("[S390] Add Documentation/s390/00-INDEX.")
Signed-off-by: Henrik Austad <henrik@austad.us>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> [rcu bits]
Acked-by: Rob Landley <rob@landley.net>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Mark Brown <broonie@kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Len Brown <len.brown@intel.com>
Cc: James Bottomley <JBottomley@parallels.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This add the following three new properties documenting and usage
for simple card:
"simple-audio-card,name",
"simple-audio-card,widgets",
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The clkc has its registers in the range of the slcr.
Instead of passing around the slcr base address pointer, let the clkc get the
address from the DT.
This prepares the slcr to be a real driver with multiple memory ranges
(slcr, clocks, pinctrl,...)
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
