Reset controller changes for v4.8, part 2
- add Amlogic Meson SoC Reset Controller driver
* tag 'reset-for-4.8-2' of git://git.pengutronix.de/git/pza/linux:
dt-bindings: reset: Add bindings for the Meson SoC Reset Controller
reset: Add support for the Amlogic Meson SoC Reset Controller
Signed-off-by: Olof Johansson <olof@lixom.net>
Drivers for 4.8:
- Add a driver for the EBI
* tag 'at91-ab-4.8-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
memory: atmel-ebi: add DT bindings documentation
memory: add Atmel EBI (External Bus Interface) driver
Signed-off-by: Olof Johansson <olof@lixom.net>
Topic branch for adding Exynos 5410 Odroid XU board for v4.8.
This brings support for Hardkernel's Odroid XU board. It was the first
design with big.LITTLE SoC from Samsung: Exynos5410. The board is not
very popular. Newer XU3 and XU4 got more attention.
Board details:
1. Exynos5410 octa-core (A15+A7, however as of now only one cluster is
enabled),
2. 2 GB DDR3 RAM,
3. PowerVR SGX544MP3 GPU (not enabled in DTS),
4. USB 3.0 Host x 1, USB 3.0 OTG x 1, USB 2.0 Host x 4,
5. HDMI 1.4a, MIPI DSI and Display Port (Display Port not on all of
revisions though),
6. eMMC 4.5 and microSD slots.
* tag 'samsung-dt-odroid-xu-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (28 commits)
ARM: dts: exynos: Add watchdog and Security SubSystem to Exynos5410
ARM: dts: exynos: Configure PWM, usb3503, PMIC and thermal on Odroid XU board
ARM: dts: exynos: Add Thermal Management Unit to Exynos5410
ARM: dts: exynos: Interrupt for USB DWC3-1 differs between Exynos5420 and 5410
dt-bindings: clock: Add watchdog and SSS clock IDs to Exynos5410
dt-bindings: clock: Add TMU clock ID to Exynos5410
ARM: dts: exynos: Add RTC and I2C to Exynos5410
ARM: dts: exynos: Add I2C, PWM and UART pinctrl to Exynos5410
ARM: dts: exynos: Move HSI2C nodes to exynos54xx.dtsi
ARM: dts: exynos: Add initial support for Odroid XU board
ARM: dts: exynos: Add USB to Exynos5410
ARM: dts: exynos: Move common Exynos5410/542x/5800 nodes to new DTSI
ARM: dts: exynos: MCT is not an interrupt controller and extend length of iomap
ARM: dts: exynos: Enable UART3 on Exynos5410
ARM: dts: exynos: Include common exynos5 in exynos5410.dtsi
ARM: dts: exynos: Move Exynos5250 and Exynos5420 nodes under soc
ARM: dts: exynos: Use phandle to get parent node in exynos5250-snow
ARM: dts: exynos: Prepare for inclusion of exynos5.dtsi in exynos5410.dtsi
ARM: dts: exynos: Move common nodes to exynos5.dtsi
ARM: dts: exynos: Split Odroid XU3 LEDs to separate DTSI
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Some I2C devices have multiple addresses assigned, for example each address
corresponding to a different internal register map page of the device.
So far drivers which need support for this have handled this with a driver
specific and non-generic implementation, e.g. passing the additional address
via platform data.
This patch provides a new helper function called i2c_new_secondary_device()
which is intended to provide a generic way to get the secondary address
as well as instantiate a struct i2c_client for the secondary address.
The function expects a pointer to the primary i2c_client, a name
for the secondary address and an optional default address. The name is used
as a handle to specify which secondary address to get.
The default address is used as a fallback in case no secondary address
was explicitly specified. In case no secondary address and no default
address were specified the function returns NULL.
For now the function only supports look-up of the secondary address
from devicetree, but it can be extended in the future
to for example support board files and/or ACPI.
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@veo-labs.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Tegra AGIC interrupt controller is compatible with the ARM GIC-400
interrupt controller. Add the compatible string and clock information
for the AGIC to the GIC device-tree binding documentation.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add the device tree binding documentation for Mediatek HDMI,
HDMI PHY and HDMI DDC devices.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
The i.MX6 Q/DL has an erratum (ERR006687) that prevents the FEC from
waking the CPUs when they are in wait(unclocked) state. As the hardware
workaround isn't applicable to all boards, disable the deeper idle state
when the workaround isn't present and the FEC is in use.
This allows to safely run a kernel with CPUidle enabled on all i.MX6
boards.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: David S. Miller <davem@davemloft.net> (for network changes)
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull i2c fixes from Wolfram Sang:
- a bigger fix for i801 to finally be able to be loaded on some
machines again
- smaller driver fixes
- documentation update because of a renamed file
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: mux: reg: Provide of_match_table
i2c: mux: refer to i2c-mux.txt
i2c: octeon: Avoid printk after too long SMBUS message
i2c: octeon: Missing AAK flag in case of I2C_M_RECV_LEN
i2c: i801: Allow ACPI SystemIO OpRegion to conflict with PCI BAR
Pull DeviceTree fixes from Rob Herring:
- fix unflatten_dt_nodes when dad parameter is set.
- add vendor prefixes for TechNexion and UniWest
- documentation fix for Marvell BT
- OF IRQ kerneldoc fixes
- restrict CMA alignment adjustments to non dma-coherent
- a couple of warning fixes in reserved-memory code
- DT maintainers updates
* tag 'devicetree-fixes-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
drivers: of: add definition of early_init_dt_alloc_reserved_memory_arch
drivers/of: Fix depth for sub-tree blob in unflatten_dt_nodes()
drivers: of: Fix of_pci.h header guard
dt-bindings: Add vendor prefix for TechNexion
of: add vendor prefix for UniWest
dt: bindings: fix documentation for MARVELL's bt-sd8xxx wireless device
of: add missing const for of_parse_phandle_with_args() in !CONFIG_OF
of: silence warnings due to max() usage
drivers: of: of_reserved_mem: fixup the CMA alignment not to affect dma-coherent
of: irq: fix of_irq_get[_byname]() kernel-doc
MAINTAINERS: DeviceTree maintainer updates
Add the Device Tree binding documentation that allows to describe the PCIe
controller found in the Axis ARTPEC-6 SoC.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Change "mdio-parent-bus" from mandatory section to optional
as it won't be required by integrated MDIO multiplexer
which has bus selection and mdio transaction generation logic,
integrated inside.
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/sched/act_police.c
net/sched/sch_drr.c
net/sched/sch_hfsc.c
net/sched/sch_prio.c
net/sched/sch_red.c
net/sched/sch_tbf.c
In net-next the drop methods of the packet schedulers got removed, so
the bug fixes to them in 'net' are irrelevant.
A packet action unload crash fix conflicts with the addition of the
new firstuse timestamp.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PWMSS device tree nodes for DRA7 SoC family and add documentation
for dt bindings.
Signed-off-by: Vignesh R <vigneshr@ti.com>
[fcooper@ti.com: Add eCAP and use updated bindings for PWMSS and ePWM]
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Previous patches switched the ECAP and EPWM to use the new bindings.
These bindings explicitly adds the various required clocks via DT rather
than depending on hwmod.
Therefore, it is safe to remove the hwmod entries since they are no longer
needed.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Switch to a new ECAP and EPWM bindings that doesn't depend on hwmod to
provide the various required clocks.
For AM437 and AM335x, add the required clocks explicitly to DT. The
hwmod entries for ECAP and EPWM will be removed and this will prevent
anything from breaking.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Replace unit address from 0 to the proper physical address. Also insure
that the unit address matches the reg property address.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that the node name has been changed from ehrpwm to pwm the document
should show this proper usage. Change the unit address in the example
from 0 to the proper physical address value that should be used. Also
insure that the unit address matches to the reg property.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are several SOC specific compatibles for ECAP, EHRPWM and PWMMS
that are in use but aren't properly documented. Therefore, fix this
by adding the compatibles to the appropriate binding documents.
While at it make minor corrections to the binding document.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for Broadcom's BCM53xx switch family, also known
as RoboSwitch. Some of these switches are ubiquituous, found in home
routers, Wi-Fi routers, DSL and cable modem gateways and other
networking related products.
This drivers adds the library driver (b53_common.c) as well as a few bus
glue drivers for MDIO, SPI, Switch Register Access Block (SRAB) and
memory-mapped I/O into a SoC's address space (Broadcom BCM63xx/33xx).
Basic operations are supported to bring the Layer 1/2 up and running,
but not much more at this point, subsequent patches add the remaining
features.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The usb power-supply on the axp22x pmics is mostly identical to the
one on the axp20x pmics. One significant difference is that it cannot
measure / monitor the usb voltage / current.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Correct references to i2c-mux.txt which was previously mux.txt.
Also correct the spelling of relevant.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Jonathan writes:
First round of IIO new device support, features and cleanups for the 4.8 cycle.
New device support
* ads1015
- add ads1115 support
* bma220 accelerometer
- new driver
- triggered buffer support.
* bmc150
- add bmm150 support.
* bmp280
- bme280 support with addition of humidity channel.
* max5487 potentiometer
- new driver
* MMA7660FC accelerometer.
- New driver
* st-pressure
- support for the lps22hb
* loop trigger.
- This one is *nasty* but we have real applications (parrot drones) where
it is useful. The trigger basically spins as hard as it can firing off
a new trigger each time all triggered devices come back to say they are
done. It doesn't hang a machine even when doing it on a dummy driver.
A lot nicer than having this implemented within lots of device drivers
anyway.
Core stuff
* Add support to create IIO devices via configfs (similar to we did for
triggers a while back) + docs.
* New channel types
- IIO_ELECTRICAL_CONDUCTIVITY
* Couple of MAINTAINERS patches to list the device tree bindings.
* Make trigger ops structure non optional (comment fix). It hasn't been for
an awful long time, but that's not what the description said.
New features
* ak8975
- support adapters that are limited to byte data only by allowing the
emulated block read i2c function that was recently introduced.
* atlas-ph
- support atlas-ec (electrical conductivity sensor)
* bmi160
- add available frequency and scale attributes to make the driver
more user friendly (and avoid having to read the datasheet to know
what will work).
* dummy
- move creation to configfs interface. It's not real hardware so we
are not that worried about the ABI breakage ;)
* mma8452
- oversampling ration support
* nau7802
- expose available gains to make life easier for userspace.
* st-sensors
- allow use of emulation for SMBus block reads as all the st parts support
it.
* ti-ads1015
- list datasheet names to allow their use by inkernel consumers.
* Various module alias additions to help auto probing. Drop one redundant one
as well.
Cleanups
* ad7266, ad7476, ad7887, ad7923, ad799x
- use direct mode claim function rather than open coding it during sensor
read (prevents switching on buffers mid read).
* ad7793, ad7791
- use direct mode claim to prevent frequency changes when buffers running.
* afe440x - These are ABI breaking but the driver requires custom userspace
code to do anything useful anyway and that is still being written and under
control of TI. Ultimately we may have other libraries to do pulse
oximetry with these devices but we aren't aware of any yet.
- kernel-doc format fixes
- drop ifdef fun around of_match_ptr - it's not worth the mess to save
a tiny amount of space.
- drop some unnecessary register initializations.
- drop the weird locked gain modes as they gain us nothing (can just set
all gains separately).
- remove handling of offset attributes seeing as no channels actually have
them (oops)
- Drop the LED3 input channel as it's an alias for ALED2.
- *big one* remove channel names - an experiment that turned out to not
make sense - see patch for details.
- use regmap fields to clean up code.
- tie the tia gain stages to appropriate channels in the ABI as that is
what they really effect. Same with the LED currents.
- cleanout some unused defines and fix a missnamed one.
* atlas-ph
- reorganise to allow support of other similar parts.
* bmc150
- document supported chips in kconfig help.
* jsa1212
- drop an unneeded i2c functionality check for functionality the driver
doesn't use.
* mxs-lradc
- simply touch screen registration code.
- remove the touch screen unregister as all devm based now.
- disable only those channels that are masked in hardware stop (others
are already dealt with elsewhere)
* st-sensors
- unexport st_sensors_get_buffer_element as nothing outside the st-sensors
core driver uses it.
- fix handling of failure to start up regulators.
* tpl0102
- drop an i2c functionality test for features that aren't needed.
* ti-am335x
- use variable name rather than type in sizeof for clarity.
- use SIMPLE_DEV_PM_OPS helper macro to tidy up a bit.
Tools
* Add install / uninstall to makefile. Someone cares, so presumably
some people will find it useful!
* generic_buffer
- rename to iio_generic_buffer to line up with other tools.
- handle cleanup when receiving signals
- Add a --device-num option and a --trigger-num option rather than
relying on naming which doesn't work if you have two of the same part.
AUDIO-CLKOUTn can asynchronizes with L/R clock.
AUDIO-CLKOUTn synchronizes with L/R clock is now default behavior.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch changes the compatibility string to match with the smallest
supported chip (EP7209). Since the DT-support for this CPU is not yet
announced, this change is safe.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch changes the compatibility string to match with the smallest
supported chip (EP7209). Since the DT-support for this CPU is not yet
announced, this change is safe.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
At least the EHCI/OHCI found on the Allwinnner H3 SoC needs multiple
reset lines, the controller will not initialize while the reset for
its companion is still asserted, which means we need to de-assert
2 resets for the controller to work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to the save power consumption, as a workaround, suspend
forcibly the USB PORTA/B/C via set the SUSPEND_A/B/C bits of OHCI
Interrupt Configuration Register in the SFRs while OHCI USB suspend.
This suspend operation must be done before the USB clock is disabled,
resume after the USB clock is enabled.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uniperiph-id, version and mode are ST specific bindings and
need the 'st,' prefix. Update the examples, as otherwise copying
them yields a runtime error parsing the DT node.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Maxim Semiconductor's PMIC MAX77620/MAX20024 has 8 GPIO pins
which act as GPIO as well as special function mode.
Add DT binding document to support these pins in GPIO
mode via GPIO framework.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add binding document for Broadcom BCM23550 SoC.
BCM23550 has a Cluster Dormant Control IP block that holds cores
in an idle state. Introduce a new CPU enable method in which the CDC is
accessed to bring the core online.
Signed-off-by: Chris Brand <chris.brand@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The axp20x pmics have 2 power inputs, one called ACIN which is intended
for to be supplied via a powerbarrel on the board and one called VBUS
which is intended to be supplied via an otg connector.
In the VBUS case the pmic needs to know if the board is supplying power
to the otg connector, because then it should not take any power from
its VBUS pin. The axp209 pmic has a N_VBUSEN input pin via which the
board can signal to the pmic whether the board is supplying power to the
otg connector or not.
On the axp221/axp223 this pin can alternatively be used as an output
which controls an external regulator which (optionally) supplies
power to the otg connector from the board. When the pin is used as
output it is called DRIVEVBUS in the datasheet.
This commit adds support for the DRIVEVBUS pin as an extra pmic
controlled regulator. Since this is optional a new x-powers,drivebus dt
property is added. When this is present the misc-control register is
written to change the N_VBUSEN input pin to DRIVEVBUS output pin mode and
the extra drivebus regulator is registered with the regulator subsystem.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
