This driver currently only supports legacy platform data probe. This
change adds device tree support and gets rid of platform data probe code
since no one is actually using mpr121 platform data in the mainline.
The device tree property parsing code is based on the work of
atmel_captouch driver.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds device tree bindings for the TI ADS7950 family of A/DC chips.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Johannes Berg says:
====================
For 4.11, we seem to have more than in the past few releases:
* socket owner support for connections, so when the wifi
manager (e.g. wpa_supplicant) is killed, connections are
torn down - wpa_supplicant is critical to managing certain
operations, and can opt in to this where applicable
* minstrel & minstrel_ht updates to be more efficient (time and space)
* set wifi_acked/wifi_acked_valid for skb->destructor use in the
kernel, which was already available to userspace
* don't indicate new mesh peers that might be used if there's no
room to add them
* multicast-to-unicast support in mac80211, for better medium usage
(since unicast frames can use *much* higher rates, by ~3 orders of
magnitude)
* add API to read channel (frequency) limitations from DT
* add infrastructure to allow randomizing public action frames for
MAC address privacy (still requires driver support)
* many cleanups and small improvements/fixes across the board
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for TI TMP007 - 16 bit IR thermopile sensor with integrated Math engine.
Sensor takes care of calculating the object temperature with the help of calibrated constants stored in non-volatile memory,
thereby reducing the calculation overhead.
Signed-off-by: Manivannan Sadhasivam <manivannanece23@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Rockchip's RC produces a 100MHz reference clock but there are two methods
for the PHY to generate it:
(1) Use the system PLL to generate a 100MHz clock. The PHY will relock
it, filter signal noise, and output the reference clock. ASPM L0s
works correctly, but circuit noise issues make it difficult to pass
the TX compatibility test.
(2) Share the SoC's 24MHZ crystal oscillator with the PHY and force the
PHY's PLL to generate 100MHz internally. In this case, exit from
ASPM L0s sometimes fails due to a design error in the RC receiver
circuit. Even if we use extended-synch, the PHY sometimes fails to
relock the bits from FTS, which will hang the system.
We want the flexibility to use both clocking methods, so add a DT property,
"aspm-no-l0s". If that's present, disable L0s to avoid the issues with
case (2).
[bhelgaas: changelog]
Reported-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Falling back unconditionally to HostNotify as primary client's interrupt
breaks some drivers which alter their functionality depending on whether
interrupt is present or not, so let's introduce a board flag telling I2C
core explicitly if we want wired interrupt or HostNotify-based one:
I2C_CLIENT_HOST_NOTIFY.
For DT-based systems we introduce "host-notify" property that we convert
to I2C_CLIENT_HOST_NOTIFY board flag.
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix couple of typos in the example given in the TI syscon reset
binding. The ti,reset-bits used for DSP0 are corrected to match
the values that will be used in the actual DT node.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The bq27xxx binding is a standard i2c style binding, however the
deprecated compatible fields and different revisions warrant its own
documentation.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
'uart-has-rtscts' is a generic serial property and it is described
at Documentation/devicetree/bindings/serial/serial.txt, so remove it
from the specific fsl-imx-uart binding documentation.
While at it, add a note pointing to the serial.txt file, which
contains the complete list of generic serial bindings.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The vendor prefix for Fujitsu is used in the tree, but it's
still missing from the documentation, so add it. Fujitsu Ltd.
is a japanese ICT company, http://www.fujitsu.com
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
In the new DTS bindings for DSA (dsa2), the "ethernet" and "link"
phandles are respectively mandatory and exclusive to CPU port and DSA
link device tree nodes.
Simplify dsa2.c a bit by checking the presence of such phandle instead
of checking the redundant "label" property.
Then the Linux philosophy for Ethernet switch ports is to expose them to
userspace as standard NICs by default. Thus use the standard enumerated
"eth%d" device name if no "label" property is provided for a user port.
This allows to save DTS files from subjective net device names.
If one wants to rename an interface, udev rules can be used as usual.
Of course the current behavior is unchanged, and the optional "label"
property for user ports has precedence over the enumerated name.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds device tree bindings document for ZTE zx2967
family power domain controller.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add DT bindings for avia,hx711
Add vendor avia to vendor list
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The earlier deployed LIS3LV02DL driver had already defined a few
DT bindings that need to be supported by the new more generic
driver and listed as compatible but deprecated bindings in the
documentation.
After this we can start to activate the new driver with the old
systems where applicable.
As part of this enablement: make us depend on the old drivers
not being in use so we don't get a kernel with two competing
drivers.
Cc: devicetree@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Shenzhen Xunlong Software CO.,Limited is a SBC vendor, which produces
the "Orange Pi" series of SBCs.
Add a vendor prefix for it. This prefix is already used in many
Allwinner H3 boards.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Lichee Pi is a new "Pi"-named development board series.
Currently available device, Lichee Pi One, is by only one person as
night job, so the device series name is chosen to be the vendor prefix.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add bindings documentation for the ADC128D818 driver, featuring default I2C
properties along with the optional 'mode' property for chip operation mode
selection (see datasheet, sec. 8.4.1).
Signed-off-by: Alexander Koch <mail@alexanderkoch.net>
Acked-by: Michael Hornung <mhornung.linux@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
[groeck: Fixed whitespace error]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Creation of dt include file for specific stm32f4 clocks.
These specific clocks are not derived from system clock (SYSCLOCK)
We should use index 1 to use these clocks in DT.
e.g. <&rcc 1 CLK_LSI>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Renesas ARM64 Based SoC DT Updates for v4.11
* Add PWM, and sound MIX and CTU support to r8a7795 SoC
* Add CAN, CAN FD and all MSIOF nodes to r8a7796 SoC
* Use Gen 3 fallback binding for i2c, msiof, PCIE and USB2 phy
* Enable Ethernet and 4 GiB memory on r8a7796/salvator-x board
* Add r8a7796/salvator-x board part number to bindings
* tag 'renesas-arm64-dt-for-v4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: r8a7795: Add PWM support
arm64: dts: r8a7796: Use R-Car Gen 3 fallback binding for msiof nodes
arm64: dts: r8a7796: salvator-x: Enable EthernetAVB
arm64: dts: renesas: r8a7796: Add EthernetAVB instance
arm64: dts: r8a7796: salvator-x: Update memory node to 4 GiB map
arm64: dts: r8a7796: Use R-Car Gen 3 fallback binding for i2c nodes
arm64: dts: r8a7795: Use R-Car Gen 3 fallback binding for i2c nodes
arm64: dts: r8a7795: Use Gen 3 fallback compat string for PCIE
arm64: dts: r8a7795: add sound MIX support
arm64: dts: r8a7795: add sound CTU support
arm64: dts: r8a7795: Use renesas,rcar-gen3-usb2-phy fallback binding
arm64: renesas: r8a7796/salvator-x: Add board part number to DT bindings
arm64: dts: r8a7796: Add CAN FD support
arm64: dts: r8a7796: Add CAN support
arm64: dts: r8a7796: Add CAN external clock support
arm64: dts: r8a7796: Add all MSIOF nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds entry for LWN - the Liebherr-Werk Nenzing GmbH company to
vendor-prefixes.txt file.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add interrupt specifiers for USB and AC charger input. Interrupt numbers
are from the datasheet.
Fix wrong property for compatible string.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The CDCE925 is a member of the CDCE(L)9xx programmable clock generator
family. There are also CDCE913, CDCE937, CDCE949 which have different
number of PLLs and outputs.
The clk-cdce925 driver supports only CDCE925 in the family. This adds
support for the CDCE913, CDCE937, CDCE949, too.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Mike Looijmans <mike.looijmans@topic.nl>
Cc: Michael Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds a new glue driver called dwmac-dwc-qos-eth which
was based in the dwc_eth_qos as is. To assure retro-compatibility a slight
tweak was also added to stmmac_platform.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Tested-by: Niklas Cassel <niklas.cassel@axis.com>
Reviewed-by: Lars Persson <larper@axis.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new parameter to the stmmac DT: snps,en-tx-lpi-clockgating.
It was ported from synopsys/dwc_eth_qos.c and it is useful if lpi tx clock
gating is needed by stmmac users also.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Tested-by: Niklas Cassel <niklas.cassel@axis.com>
Reviewed-by: Lars Persson <larper@axis.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SoC family such as DRA7 family of processors have, in addition
to the regular muxing of pins (as done by pinctrl-single), a separate
hardware module called IODelay which is also expected to be configured.
The "IODelay" module has it's own register space that is independent
of the control module and the padconf register area.
With recent changes to the pinctrl framework, we can now support
this hardware with a reasonably minimal driver by using #pinctrl-cells,
GENERIC_PINCTRL_GROUPS and GENERIC_PINMUX_FUNCTIONS.
It is advocated strongly in TI's official documentation considering
the existing design of the DRA7 family of processors during mux or
IODelay reconfiguration, there is a potential for a significant glitch
which may cause functional impairment to certain hardware. It is
hence recommended to do as little of muxing as absolutely necessary
without I/O isolation (which can only be done in initial stages of
bootloader).
NOTE: with the system wide I/O isolation scheme present in DRA7 SoC
family, it is not reasonable to do stop all I/O operations for every
such pad configuration scheme. So, we will let it glitch when used in
this mode.
Even with the above limitation, certain functionality such as MMC has
mandatory need for IODelay reconfiguration requirements, depending on
speed of transfer. In these cases, with careful examination of usecase
involved, the expected glitch can be controlled such that it does not
impact functionality.
In short, IODelay module support as a padconf driver being introduced
here is not expected to do SoC wide I/O Isolation and is meant for
a limited subset of IODelay configuration requirements that need to
be dynamic and whose glitchy behavior will not cause functionality
failure for that interface.
IMPORTANT NOTE: we take the approach of keeping LOCK_BITs cleared
to 0x0 at all times, even when configuring Manual IO Timing Modes.
This is done by eliminating the LOCK_BIT=1 setting from Step
of the Manual IO timing Mode configuration procedure. This option
leaves the CFG_* registers unprotected from unintended writes to the
CTRL_CORE_PAD_* registers while Manual IO Timing Modes are configured.
This approach is taken to allow for a generic driver to exist in kernel
world that has to be used carefully in required usecases.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[tony@atomide.com: updated to use generic pinctrl functions, added
binding documentation, updated comments]
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
SATA Host 0 clock is (as correctly documented) id 15/sata0.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Rob Herring <robh@kernel.org>
The generic IOMMU binding says that the meaning of an 'IOMMU specifier'
is defined by the binding of a specific SMMU. The ARM SMMU binding
never explicitly uses the term 'specifier' at all. Update implicit
references to use the explicit term.
In the iommu-map binding change references to iommu-specifier to
"IOMMU specifier" so we are 100% consistent everywhere with terminology
and capitalization.
Signed-off-by: Stuart Yoder <stuart.yoder@nxp.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
OMAP related files are actually named ehci-omap.txt and ohci-omap3.txt.
Also add full path to ohci-omap3.txt.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
