The compatible string for this panel was specified as
toshiba,lt089ac29000.txt. I believe this is a mistake.
Fixes: 06e733e41f ("drm/panel: simple: add Toshiba LT089AC19000")
Cc: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Rob Herring <robh@kernel.org>
The drivers/net/wireless/intel/iwlwifi/pcie/drv.c conflict was
resolved using a diff provided by Kalle in his pull request.
Kalle Valo says:
====================
wireless-drivers-next patches for 4.16
A bigger pull request this time, the most visible change being the new
driver mt76. But there's also Kconfig refactoring in ath9k and ath10k,
work beginning in iwlwifi to have rate scaling in firmware/hardware,
wcn3990 support getting closer in ath10k and lots of smaller changes.
mt76
* a new driver for MT76x2e, a 2x2 PCIe 802.11ac chipset by MediaTek
ath10k
* enable multiqueue support for all hw using mac80211 wake_tx_queue op
* new Kconfig option ATH10K_SPECTRAL to save RAM
* show tx stats on QCA9880
* new qcom,ath10k-calibration-variant DT entry
* WMI layer support for wcn3990
ath9k
* new Kconfig option ATH9K_COMMON_SPECTRAL to save RAM
wcn36xx
* hardware scan offload support
wil6210
* run-time PM support when interface is down
iwlwifi
* initial work for rate-scaling offload
* Support for new FW API version 36
* Rename the temporary hw name A000 to 22000
ssb
* make SSB a menuconfig to ease disabling it all
mwl8k
* enable non-DFS 5G channels 149-165
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2017-12-18
Here's the first bluetooth-next pull request for the 4.16 kernel.
- hci_ll: multiple cleanups & fixes
- Remove Gustavo Padovan from the MAINTAINERS file
- Support BLE Adversing while connected (if the controller can do it)
- DT updates for TI chips
- Various other smaller cleanups & fixes
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
SLIMbus (Serial Low Power Interchip Media Bus) is a specification
developed by MIPI (Mobile Industry Processor Interface) alliance.
SLIMbus is a 2-wire implementation, which is used to communicate with
peripheral components like audio-codec.
This patch adds device tree bindings for the slimbus.
Signed-off-by: Sagar Dharia <sdharia@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviwed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As a kernel newcomer, I got bitten by lack of examples on this front. I
had troubles figuring out where these clocks could be defined ("/clocks"
is where the generic infrastructure expects them).
One should also ensure that a unique name is used. Generic names such as
"osc" tend to be already used by some board-wide clock crystals.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I was getting this trace along with a disabled IRQ when I was generating
heavy traffic over four daisy-chained UARTs (MAX14830) on my test kit
(Marvell Armada AM388, Solidrun Clearfog Base):
irq 51: nobody cared (try booting with the "irqpoll" option)
CPU: 0 PID: 68 Comm: irq/51-spi1.2 Not tainted 4.14.4 #7
Hardware name: Marvell Armada 380/385 (Device Tree)
[<c0110ba4>] (unwind_backtrace) from [<c010c1d8>] (show_stack+0x10/0x14)
[<c010c1d8>] (show_stack) from [<c07776ac>] (dump_stack+0x84/0x98)
[<c07776ac>] (dump_stack) from [<c016bdfc>] (__report_bad_irq+0x28/0xcc)
[<c016bdfc>] (__report_bad_irq) from [<c016c204>] (note_interrupt+0x28c/0x2dc)
[<c016c204>] (note_interrupt) from [<c01695d4>] (handle_irq_event_percpu+0x4c/0x58)
[<c01695d4>] (handle_irq_event_percpu) from [<c0169624>] (handle_irq_event+0x44/0x68)
[<c0169624>] (handle_irq_event) from [<c016ce80>] (handle_edge_irq+0x12c/0x1dc)
[<c016ce80>] (handle_edge_irq) from [<c016872c>] (generic_handle_irq+0x24/0x34)
[<c016872c>] (generic_handle_irq) from [<c03fc5a0>] (mvebu_gpio_irq_handler+0xe0/0x184)
[<c03fc5a0>] (mvebu_gpio_irq_handler) from [<c016872c>] (generic_handle_irq+0x24/0x34)
[<c016872c>] (generic_handle_irq) from [<c0168c4c>] (__handle_domain_irq+0x5c/0xb4)
[<c0168c4c>] (__handle_domain_irq) from [<c0101520>] (gic_handle_irq+0x4c/0x90)
[<c0101520>] (gic_handle_irq) from [<c010ce4c>] (__irq_svc+0x6c/0x90)
Exception stack(0xeea77c30 to 0xeea77c78)
7c20: 0000000a 018cba80 0000000a f098f680
7c40: 0000020a f098f680 00000008 0000020a 018cba80 00000001 ee9302a0 eea76000
7c60: ef2b2640 eea77c80 c050687c c0506894 80070013 ffffffff
[<c010ce4c>] (__irq_svc) from [<c0506894>] (orion_spi_setup_transfer+0x118/0x20c)
[<c0506894>] (orion_spi_setup_transfer) from [<c05069ac>] (orion_spi_transfer_one+0x1c/0x26c)
[<c05069ac>] (orion_spi_transfer_one) from [<c05060e4>] (spi_transfer_one_message+0xec/0x500)
[<c05060e4>] (spi_transfer_one_message) from [<c05059a4>] (__spi_pump_messages+0x3f4/0x680)
[<c05059a4>] (__spi_pump_messages) from [<c0505e38>] (__spi_sync+0x1fc/0x200)
[<c0505e38>] (__spi_sync) from [<c0505e60>] (spi_sync+0x24/0x3c)
[<c0505e60>] (spi_sync) from [<c0505f48>] (spi_write_then_read+0xd0/0x17c)
[<c0505f48>] (spi_write_then_read) from [<c0482efc>] (_regmap_raw_read+0xb0/0x250)
[<c0482efc>] (_regmap_raw_read) from [<c04830c0>] (_regmap_bus_read+0x24/0x4c)
[<c04830c0>] (_regmap_bus_read) from [<c04826f4>] (_regmap_read+0x60/0x148)
[<c04826f4>] (_regmap_read) from [<c0482818>] (regmap_read+0x3c/0x5c)
[<c0482818>] (regmap_read) from [<c04592b4>] (max310x_port_irq+0x104/0x2dc)
[<c04592b4>] (max310x_port_irq) from [<c0459a40>] (max310x_ist+0x68/0xc0)
[<c0459a40>] (max310x_ist) from [<c016a610>] (irq_thread_fn+0x1c/0x54)
[<c016a610>] (irq_thread_fn) from [<c016a8d8>] (irq_thread+0x12c/0x1f0)
[<c016a8d8>] (irq_thread) from [<c013e560>] (kthread+0x128/0x158)
[<c013e560>] (kthread) from [<c0107a50>] (ret_from_fork+0x14/0x24)
handlers:
[<c0169694>] irq_default_primary_handler threaded [<c04599d8>] max310x_ist
Disabling IRQ #51
On a multi-UART max310x, each UART has its own interrupt status register
which automatically de-asserts the IRQ line upon read. (There are also
top-level IRQ indicator registers which are not clear-on-read, but they
are not relevant here.) It was quite possible to receive a pending IRQ
for, e.g., UART0, enter the threaded IRQ handler, clear the ISR for
UART0 which de-asserts the IRQ line, and then race with another event on
the same chip, but a different UART channel. That resulted in another
edge on the shared-within-the-chip IRQ line which got intercepted by the
kernel.
That all led to an edge-level interrupt which was not being handled by
anybody because our threaded handler hasn't finished yet. As the chip
actually uses *level* triggered IRQs, let's convert the example DT
bindings to these.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
max-memory-bandwidth can be used to specify the maximum bandwidth dispc
can use when reading display data from main memory.
In some SoC (am437x for example) we have memory bandwidth limitation
which causes underflow in the display subsystem.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The vendor name was "toppoly" but other panels and the vendor list
have defined it as "tpo". So let's fix it in driver and bindings.
We keep the old definition in parallel to stay compatible with
potential older DTB setup.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Certain EEPROMS have a size that is larger than the number of address
bytes would allow, and store the MSB of the address in bit 3 of the
instruction byte.
This can be described in platform data using EE_INSTR_BIT3_IS_ADDR, or
in DT using the obsolete legacy "at25,addr-mode" property.
But currently there exists no non-deprecated way to describe this in DT.
Hence extend the existing "address-width" DT property to allow
specifying 9 address bits, and enable support for that in the driver.
This has been tested with a Microchip 25LC040A.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drm-misc-next for 4.16:
Cross-subsystem Changes:
- Documentation for amlogic dt dt-bindings
Core Changes:
- Update edid-derived drm_display_info fields at edid property set
Driver Changes:
- A bunch of clean up from Noralf, including the last patches to reduce
fbdev emulation footprint.
* tag 'drm-misc-next-2017-12-14' of git://anongit.freedesktop.org/drm/drm-misc: (30 commits)
drm/atomic-helper: Make zpos property kerneldoc less misleading
drm: Update edid-derived drm_display_info fields at edid property set [v2]
MAINTAINERS: Remove Jani as drm-misc co-maintainer
drm/tinydrm: Use drm_fb_cma_fbdev_init_with_funcs/fini()
drm/arm/mali: Use drm_fb_cma_fbdev_init/fini()
drm/zte: Use drm_fb_cma_fbdev_init/fini()
drm/vc4: Use drm_fb_cma_fbdev_init/fini()
drm/tve200: Use drm_fb_cma_fbdev_init/fini()
drm/tilcdc: Use drm_fb_cma_fbdev_init/fini()
drm/sun4i: Use drm_fb_cma_fbdev_init/fini()
drm/stm: Use drm_fb_cma_fbdev_init/fini()
drm/sti: Use drm_fb_cma_fbdev_init/fini()
drm/pl111: Use drm_fb_cma_fbdev_init/fini()
drm/imx: Use drm_fb_cma_fbdev_init/fini()
drm/atmel-hlcdc: Use drm_fb_cma_fbdev_init/fini()
drm/cma-helper: Add drm_fb_cma_fbdev_init/fini()
drm/gem-fb-helper: drm_gem_fbdev_fb_create() make funcs optional
drm/tegra: Use drm_fb_helper_lastclose() and _poll_changed()
drm/rockchip: Use drm_fb_helper_lastclose() and _poll_changed()
drm/omap: Use drm_fb_helper_lastclose() and _poll_changed()
...
Document the devicetree bindings that describe Texas Instruments
opp-supply which allow a platform to describe multiple regulators and
additional information, such as registers containing data needed to
program aforementioned regulators.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Three sets of overlapping changes, two in the packet scheduler
and one in the meson-gxl PHY driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
The rk3328 quad-core Cortex A53 uses a Mali-450MP2 with 2 PPs, so
add a compatible for it.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Message Manager's mailbox interrupts are queue based and not proxy
specific. The interrupt names are wrong in the binding, however
correctly reflected in the example provided. Remove the relation
to proxy ID in the documentation of binding. Existing device tree
descriptions follow the correct conventions already and documentation
update has been missed.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Rob Herring <robh@kernel.org>
These properties have been in use for a very long time (at least since
2005), but were never documented in chosen.txt.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Rob Herring <robh@kernel.org>
Update the device tree binding documentation for the Marvell EBU UART,
in order to allow describing the extended UART IP block, in addition to
the already supported standard UART IP. This requires adding a new
compatible string, the introduction of a clocks property, and extensions
to the interrupts property.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add "sff,sff" for SFF module support with SFP. These have a different
phys_id value, and also have the present and rate select signals omitted
compared with their socketed counter-parts.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ti-sysc binding does not yet describe the capabilities of the
interconnect target module. So to make the ti-sysc binding usable
for configuring the interconnect target module, we need to add few
more properties:
1. To detect between omap2 and omap4 timers, let's add compatibles
for them for "ti,sysc-omap2-timer" and,sysc-omap4-timer". This
makes it easier to pick up the already initialized system timers
later on
2. Let's add "ti,sysc-mask" for a mask of features supported by the
interconnect target module. This describes what we have available
in the various SYSCONFIG registers
3. Let's add "ti,sysc-midle" and "ti,sysc-sidle" lists for the master
and slave idle modes supported by the interconnect target module.
These describe the values available for MIDLE and SIDLE bits in
the SYSCONFIG registers
4. Some interconnect target modules need a short delay after reset
before they can be accessed, let's use "ti,sysc-delay-us" for
that
5. Let's add "ti,syss-mask" bit to describe the optional SYSSTATUS
register bits for reset done bits
6. Let's support the two existing custom quirk properties already
listed in Documentation/devicetree/bindings/arm/omap/omap.txt for
"ti,no-reset-on-init" and "ti,no-idle-on-init"
7. And finally, let's add a header for the binding for the dts
files and the driver to use
Cc: Benoît Cousson <bcousson@baylibre.com>
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Nishanth Menon <nm@ti.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: Suman Anna <s-anna@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update the compatible string and Device Tree binding document for
7278B0.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for 4.16. Major changes:
ath10k
* enable multiqueue support for all hw using mac80211 wake_tx_queue op
* new Kconfig option ATH10K_SPECTRAL to save RAM
* show tx stats on QCA9880
* new qcom,ath10k-calibration-variant DT entry
* WMI layer support for wcn3990
ath9k
* new Kconfig option ATH9K_COMMON_SPECTRAL to save RAM
wcn36xx
* hardware scan offload support
wil6210
* run-time PM support when interface is down
The bus + bmi-chip-id + bmi-board-id is not enough to identify the correct
board data file on QCA4019 based devices. Multiple different boards share
the same values. Only the original reference designs can currently be
identified and loaded from the board-2.bin. But these will not result in
the correct calibration data when combined with the pre-calibration data
from the device.
An additional "variant" information has to be provided (via SMBIOS or DT)
to select the correct board data for a design which was modified by an ODM.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Guide users to maintain the proper balance between native and GPIO chip
selects.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently only the MSIOF_SYNC signal can be used as a native chip
select. Extend support to up to 3 native chipselects using the
MSIOF_SS1 and MSIOF_SS2 signals.
Inspired by a patch in the BSP by Hiromitsu Yamasaki.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add binding documentation for the Video Decoder Engine which is found
on NVIDIA Tegra20/30/114/124/132 SoC's.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some PHYs need a minimum time after the reset gpio was asserted and/or
deasserted. To ensure we meet these timing requirements add two new
optional devicetree parameters for the phy: reset-delay-us and
reset-post-delay-us.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the SOR bindings for Tegra186, in which a new property is
required to identify the instance of the SOR interface and the clock
tree has slightly changed as well.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Document r8a774[35] specific compatible strings. The Renesas RZ/G1[ME]
(r8a774[35]) sound modules are identical to the R-Car Gen2 family.
No driver change is needed as the fallback compatible string
"renesas,rcar_sound-gen2" activates the right code in the driver.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
As opposed to earlier incarnations, the memory controller on Tegra186 no
longer implements an SMMU. Instead the SMMU is a regular ARM SMMU and in
a separate IP block.
However, the memory controller programs the SMMU stream IDs for each of
the memory clients. Add a header file with definitions for each of these
stream IDs and mark the #iommu-cells property as required on Tegra30 to
Tegra210 in the device tree bindings.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The MISC register block found on Tegra186 SoCs contains registers that
can be used to identify a given chip and various strapping options.
Signed-off-by: Thierry Reding <treding@nvidia.com>
A new version of the HIDMA IP has been released with bug fixes. Bumping the
hardware version to differentiate from others.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This adds a compatible string for the Texas Instruments CC2560 Bluetooth
chip to the existing TI WiLink shared transport bindings. These chips are
similar enough that the same bindings work for both. The file is renamed
to ti-bluetooth.txt to make it more generic.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In order to improve the bindings documentation, explicitly pass the name
of the clocks: "qspi_en" and "qspi", which are mandatory.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
This adds optional nvmem consumer properties to the ti,wlink-st device tree
bindings to allow specifying the BD address.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This reverts commit b07815d4ea.
The reverted commit was merged into v4-15-rc1 by mistake: it was taken
from the IMX tree but the patch has never been sent to linux-mtd nor
reviewed by any spi-nor maintainers.
Actually, it would have been rejected since we add new values for the
'compatible' DT property only for SPI NOR memories that don't support
the JEDEC READ ID op code (0x9F).
Both en25s64 and sst25wf040b support the JEDEC READ ID op code, hence
should use the "jedec,spi-nor" string alone as 'compatible' value.
See the following link for more details:
http://lists.infradead.org/pipermail/linux-mtd/2017-November/077425.html
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
