On PCscsi, the FENAB configuration also enables 24-bit DMA
transfer lengths (and provides the chip id in TCHI after reset).
We want to be able to enable this parameter from the DMA driver.
Check if the caller of scsi_esp_register provided a value for esp->config2.
If this is the case, assume this is not an ESP100, skip the detection
phase and leave esp->config2 untouched. It will be used in esp_reset_esp.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The am53c974 returns the same ID as the FAS236, but implements
things slightly differently. So detect the am53c974 by checking
for ESP_CONFIG4 register.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The am53c974 has an design issue where a single byte might be
left in the SCSI FIFO after a DMA transfer.
As the handling code is currently untested add a WARN_ON()
statement here.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch adds a new implementation for the Tekram DC-390T /
AMD AM53c974 SCSI controller, based on the generic
esp_scsi infrastructure.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Using DMA for command submission has the drawback that it might
generate additional DMA completion interrupts after the command
has been submitted to the device.
Additionally the am53c974 has a design flaw causing it
to generate spurious interrupts even though DMA completion
interrupts are not enabled.
This can be avoided by using the FIFO for command submission.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
A read to ESP_INTRPT will clear ESP_STATUS and ESP_SSTEP. So read
all status registers in one go to avoid losing information.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add new debug definitions for event and command logging.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Use dev_printk functions for correct device annotations.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add a field 'num_tags' to the esp structure to allow drivers
to overwrite the number of avialable tags if required.
Default is ESP_DEFAULT_TAGS.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Use generic io stats accounting help functions (generic_{start,end}_io_acct)
to simplify io stat accounting.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Acked-by: Kent Overstreet <kmo@datera.io>
Signed-off-by: Jens Axboe <axboe@fb.com>
Many block drivers accounting io stat based on bio (e.g. NVMe...),
the blk_account_io_start/end() which is based on request
does not make sense to them, so here we introduce the similar help
function named generic_start/end_io_acct base on raw sectors, and it can
simplify some driver's open io accounting code.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Don't duplicate the code to handle the not cpu bounce case in the
caller, do it inside blk_mq_hctx_next_cpu instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Propagate the returned error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
v3.18-rc6 contains an important DT bug fix, c1a2086e2d, "of/selftest:
Fix off-by-one error in removal path" which affects testing of the
overlay patch series. Merge it into the devicetree/next staging branch
so that the overlay patches are applied on top of a known working tree.
Linux 3.18-rc6
Conflicts:
drivers/of/address.c
Currently all get requests with an empty driver name fail with
EINVAL. Since most users actually want to supply an empty driver
name this patch removes this check.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
"That letter [the last s] is sad because all the others
have those things [=] below them and it does not."
This patch fixes the tragedy so all the letters can
be happy again.
Signed-off-by: Maisa Roponen <maisa.roponen@gmail.com>
[The author being 4 years old needed some assistance]
Signed-off-by: Tero Roponen <tero.roponen@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Copy-paste error from the previous block of error handling code.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e,e1;
@@
if (IS_ERR(e)) {
...
(
ret = PTR_ERR(e);
|
* ret = PTR_ERR(e1);
)
...
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
drivers/usb/gadget/legacy/printer.c:222:34: sparse: symbol 'ss_ep_in_comp_desc' was not declared. Should it be static?
drivers/usb/gadget/legacy/printer.c:234:34: sparse: symbol 'ss_ep_out_comp_desc' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Currently perf report on TUI doesn't print percent for first-level
callchain entry.
I guess it (wrongly) assumes that there's only a single callchain in the
first level.
This patch fixes it by handling the first level callchains same as
others - if it's not 100% it should print the percent value.
Also it'll affect other callchains in the other way around - if it's
100% (single callchain) it should not print the percentage.
Before:
- 30.95% 6.84% abc2 abc2 [.] a
- a
- 70.00% c
- 100.00% apic_timer_interrupt
smp_apic_timer_interrupt
local_apic_timer_interrupt
hrtimer_interrupt
...
+ 30.00% b
+ __libc_start_main
After:
- 30.95% 6.84% abc2 abc2 [.] a
- 77.90% a
- 70.00% c
- apic_timer_interrupt
smp_apic_timer_interrupt
local_apic_timer_interrupt
hrtimer_interrupt
...
+ 30.00% b
+ 22.10% __libc_start_main
Reported-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung.kim@lge.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1416816807-6495-1-git-send-email-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
There are not many of these messages producted by the
firmware, but they are generally fairly useful, so make it easy to print them
with a separate debug level.
kvalo: fix commit log, rename debug level
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are better ways to get the kernel information, use the
utsname and omit the version code entirely since it's duplicate.
The version magic is rather useless anyway
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Remove overly verbose debugging output that pokes into mid-layer internal
structures that looks like copy & paste from the mpt2/3 drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Merge two functions, and remove overly verbose debugging output that pokes
into mid-layer internal structures.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Merge two functions, and remove overly verbose debugging output that pokes
into mid-layer internal structures.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Drop the now unused reason argument from the ->change_queue_depth method.
Also add a return value to scsi_adjust_queue_depth, and rename it to
scsi_change_queue_depth now that it can be used as the default
->change_queue_depth implementation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
We won't ever queue more commands than the host allows. Instead of
letting drivers either reject or ignore this case handle it in
common code. Note that various driver use internal constant or
variables that are assigned to both shost->can_queue and checked
in ->change_queue_depth - I did remove those checks as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
All drivers use the implementation for ramping the queue up and down, so
instead of overloading the change_queue_depth method call the
implementation diretly if the driver opts into it by setting the
track_queue_depth flag in the host template.
Note that a few drivers validated the new queue depth in their
change_queue_depth method, but as we never go over the queue depth
set during slave_configure or the sysfs file this isn't nessecary
and can safely be removed.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Venkatesh Srinivas <venkateshs@google.com>
James Smart said the userspace to consume these events never emerged. Given
that these get in the way of the following patches remove support for them.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: James Smart <james.smart@emulex.com>
Do not process any SCSI and IOCTL command further (return them with
appropriate return values to callers), while driver removal is in
progress or PCI shutdown is invoked.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In OCR(Online Controller Reset) path, driver sets adapter state to
MEGASAS_HBA_OPERATIONAL before getting new RAID map. There will be a small
window where IO will come from OS with old RAID map. This patch will update
adapter state to MEGASAS_HBA_OPERATIONAL, only after driver has new RAID
map to avoid any IOs getting build using old RAID map.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In OCR (Online Controller Reset) path, driver sets adapter state to
MEGASAS_HBA_OPERATIONAL before getting new RAID map. There will be a small
window where IO will come from OS with old RAID map. This patch will
update adapter state to MEGASAS_HBA_OPERATIONAL, only after driver has new
RAID map to avoid any IOs getting build using old RAID map.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Update MAINTAINERS list and copyright information for megaraid_sas driver.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Update driver version and remove some meta data (release date and extended
version) about megaraid_sas driver.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When JIG was set to "boot on" mode, the UART connection did not work
because it was assigned to Dock-Car cable (path: audio), not JIG-UART-ON
cable.
This was introduced in 39bf369e4e ("extcon: max77693: Add support dock
device and buttons") while adding dock features.
Assign the JIG-UART-ON back to UART path.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[cw00.choi: Modify the patch name to remove specific board name]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Platform bus is not the only way to have extcon devices, so current
implementation of of_extcon_get_extcon_dev() is broken. Also using
parent device node only to get device name is quite ugly.
This patch reimplements of_extcon_get_extcon_dev() to do exactly the
same as extcon_get_extcon_dev() but instead of comparing names, compare
node pointers.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
[mszyprow: simplified the code]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
... and make it handle multi-segment iovecs - deals with that
"fix this later" issue for free. A bit of shame, really - it
had been there since 2.3.15pre3 when the whole thing went into the
tree, practically a historical artefact by now...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
