This reverts commit 723ad91613
When client requests channel or ring size larger than what the server
can support the server will cap the request to the supported max. So,
the client would not be able to successfully request resources that
exceed the server limit.
Fixes: 723ad91613 ("ibmvnic: Add ethtool private flag for driver-defined queue limits")
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Link: https://lore.kernel.org/r/20220427235146.23189-1-drt@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Time-Specified Departure feature is indeed mutually exclusive with
TX IP checksumming in ENETC, but TX checksumming in itself is broken and
was removed from this driver in commit 82728b91f1 ("enetc: Remove Tx
checksumming offload code").
The blamed commit declared NETIF_F_HW_CSUM in dev->features to comply
with software TSO's expectations, and still did the checksumming in
software by calling skb_checksum_help(). So there isn't any restriction
for the Time-Specified Departure feature.
However, enetc_setup_tc_txtime() doesn't understand that, and blindly
looks for NETIF_F_CSUM_MASK.
Instead of checking for things which can literally never happen in the
current code base, just remove the check and let the driver offload
tc-etf qdiscs.
Fixes: acede3c5da ("net: enetc: declare NETIF_F_HW_CSUM and do it in software")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220427203017.1291634-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We need to wait 5 s for EMP reset after firmware flash. Code was extracted
from OOT driver (ice v1.8.3 downloaded from sourceforge). Without this
wait, fw_activate let card in inconsistent state and recoverable only
by second flash/activate. Flash was tested on these fw's:
From -> To
3.00 -> 3.10/3.20
3.10 -> 3.00/3.20
3.20 -> 3.00/3.10
Reproducer:
[root@host ~]# devlink dev flash pci/0000:ca:00.0 file E810_XXVDA4_FH_O_SEC_FW_1p6p1p9_NVM_3p10_PLDMoMCTP_0.11_8000AD7B.bin
Preparing to flash
[fw.mgmt] Erasing
[fw.mgmt] Erasing done
[fw.mgmt] Flashing 100%
[fw.mgmt] Flashing done 100%
[fw.undi] Erasing
[fw.undi] Erasing done
[fw.undi] Flashing 100%
[fw.undi] Flashing done 100%
[fw.netlist] Erasing
[fw.netlist] Erasing done
[fw.netlist] Flashing 100%
[fw.netlist] Flashing done 100%
Activate new firmware by devlink reload
[root@host ~]# devlink dev reload pci/0000:ca:00.0 action fw_activate
reload_actions_performed:
fw_activate
[root@host ~]# ip link show ens7f0
71: ens7f0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN mode DEFAULT group default qlen 1000
link/ether b4:96:91:dc:72:e0 brd ff:ff:ff:ff:ff:ff
altname enp202s0f0
dmesg after flash:
[ 55.120788] ice: Copyright (c) 2018, Intel Corporation.
[ 55.274734] ice 0000:ca:00.0: Get PHY capabilities failed status = -5, continuing anyway
[ 55.569797] ice 0000:ca:00.0: The DDP package was successfully loaded: ICE OS Default Package version 1.3.28.0
[ 55.603629] ice 0000:ca:00.0: Get PHY capability failed.
[ 55.608951] ice 0000:ca:00.0: ice_init_nvm_phy_type failed: -5
[ 55.647348] ice 0000:ca:00.0: PTP init successful
[ 55.675536] ice 0000:ca:00.0: DCB is enabled in the hardware, max number of TCs supported on this port are 8
[ 55.685365] ice 0000:ca:00.0: FW LLDP is disabled, DCBx/LLDP in SW mode.
[ 55.692179] ice 0000:ca:00.0: Commit DCB Configuration to the hardware
[ 55.701382] ice 0000:ca:00.0: 126.024 Gb/s available PCIe bandwidth, limited by 16.0 GT/s PCIe x8 link at 0000:c9:02.0 (capable of 252.048 Gb/s with 16.0 GT/s PCIe x16 link)
Reboot doesn’t help, only second flash/activate with OOT or patched
driver put card back in consistent state.
After patch:
[root@host ~]# devlink dev flash pci/0000:ca:00.0 file E810_XXVDA4_FH_O_SEC_FW_1p6p1p9_NVM_3p10_PLDMoMCTP_0.11_8000AD7B.bin
Preparing to flash
[fw.mgmt] Erasing
[fw.mgmt] Erasing done
[fw.mgmt] Flashing 100%
[fw.mgmt] Flashing done 100%
[fw.undi] Erasing
[fw.undi] Erasing done
[fw.undi] Flashing 100%
[fw.undi] Flashing done 100%
[fw.netlist] Erasing
[fw.netlist] Erasing done
[fw.netlist] Flashing 100%
[fw.netlist] Flashing done 100%
Activate new firmware by devlink reload
[root@host ~]# devlink dev reload pci/0000:ca:00.0 action fw_activate
reload_actions_performed:
fw_activate
[root@host ~]# ip link show ens7f0
19: ens7f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000
link/ether b4:96:91:dc:72:e0 brd ff:ff:ff:ff:ff:ff
altname enp202s0f0
Fixes: 399e27dbbd ("ice: support immediate firmware activation via devlink reload")
Signed-off-by: Petr Oros <poros@redhat.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Previous patch labelled "ice: Fix incorrect locking in
ice_vc_process_vf_msg()" fixed an issue with ignored messages
sent by VF driver but a small race window still left.
Recently caught trace during 'ip link set ... vf 0 vlan ...' operation:
[ 7332.995625] ice 0000:3b:00.0: Clearing port VLAN on VF 0
[ 7333.001023] iavf 0000:3b:01.0: Reset indication received from the PF
[ 7333.007391] iavf 0000:3b:01.0: Scheduling reset task
[ 7333.059575] iavf 0000:3b:01.0: PF returned error -5 (IAVF_ERR_PARAM) to our request 3
[ 7333.059626] ice 0000:3b:00.0: Invalid message from VF 0, opcode 3, len 4, error -1
Setting of VLAN for VF causes a reset of the affected VF using
ice_reset_vf() function that runs with cfg_lock taken:
1. ice_notify_vf_reset() informs IAVF driver that reset is needed and
IAVF schedules its own reset procedure
2. Bit ICE_VF_STATE_DIS is set in vf->vf_state
3. Misc initialization steps
4. ice_sriov_post_vsi_rebuild() -> ice_vf_set_initialized() and that
clears ICE_VF_STATE_DIS in vf->vf_state
Step 3 is mentioned race window because IAVF reset procedure runs in
parallel and one of its step is sending of VIRTCHNL_OP_GET_VF_RESOURCES
message (opcode==3). This message is handled in ice_vc_process_vf_msg()
and if it is received during the mentioned race window then it's
marked as invalid and error is returned to VF driver.
Protect vf_state check in ice_vc_process_vf_msg() by cfg_lock to avoid
this race condition.
Fixes: e6ba5273d4 ("ice: Fix race conditions between virtchnl handling and VF ndo ops")
Tested-by: Fei Liu <feliu@redhat.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Usage of mutex_trylock() in ice_vc_process_vf_msg() is incorrect
because message sent from VF is ignored and never processed.
Use mutex_lock() instead to fix the issue. It is safe because this
mutex is used to prevent races between VF related NDOs and
handlers processing request messages from VF and these handlers
are running in ice_service_task() context. Additionally move this
mutex lock prior ice_vc_is_opcode_allowed() call to avoid potential
races during allowlist access.
Fixes: e6ba5273d4 ("ice: Fix race conditions between virtchnl handling and VF ndo ops")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The hardware checksum offloading requires use of a transmit
status block inserted before the outgoing frame data, this was
updated in '9a9ba2a4aaaa ("net: bcmgenet: always enable status blocks")'
However, skb_tx_timestamp() assumes that it is passed a raw frame
and PTP parsing chokes on this status block.
Fix this by calling __skb_pull(), which hides the TSB before calling
skb_tx_timestamp(), so an outgoing PTP packet is parsed correctly.
As the data in the skb has already been set up for DMA, and the
dma_unmap_* calls use a separately stored address, there is no
no effective change in the data transmission.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220424165307.591145-1-jonathan.lemon@gmail.com
Fixes: d03825fba4 ("net: bcmgenet: add skb_tx_timestamp call")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
DSA, through dsa_port_bridge_leave(), first notifies the port of the
fact that it left a bridge, then, if that bridge was VLAN-aware, it
notifies the port of the change in VLAN awareness state, towards
VLAN-unaware mode.
So ocelot_port_vlan_filtering() can be called when ocelot_port->bridge
is NULL, and this makes ocelot_add_vlan_unaware_pvid() create a struct
ocelot_bridge_vlan with a vid of 0 and an "untagged" setting of true on
that port.
In a way this structure correctly reflects the reality, but by design,
VID 0 (OCELOT_STANDALONE_PVID) was not meant to be kept in the bridge
VLAN list of the driver, but managed separately.
Having OCELOT_STANDALONE_PVID in ocelot->vlans makes us trip up on
several sanity checks that did not expect to have this VID there.
For example, after we leave a VLAN-aware bridge and we re-join it, we
can no longer program egress-tagged VLANs to hardware:
# ip link add br0 type bridge vlan_filtering 1 && ip link set br0 up
# ip link set swp0 master br0
# ip link set swp0 nomaster
# ip link set swp0 master br0
# bridge vlan add dev swp0 vid 100
Error: mscc_ocelot_switch_lib: Port with more than one egress-untagged VLAN cannot have egress-tagged VLANs.
But this configuration is in fact supported by the hardware, since we
could use OCELOT_PORT_TAG_NATIVE. According to its comment:
/* all VLANs except the native VLAN and VID 0 are egress-tagged */
yet when assessing the eligibility for this mode, we do not check for
VID 0 in ocelot_port_uses_native_vlan(), instead we just ensure that
ocelot_port_num_untagged_vlans() == 1. This is simply because VID 0
doesn't have a bridge VLAN structure.
The way I identify the problem is that ocelot_port_vlan_filtering(false)
only means to call ocelot_add_vlan_unaware_pvid() when we dynamically
turn off VLAN awareness for a bridge we are under, and the PVID changes
from the bridge PVID to a reserved PVID based on the bridge number.
Since OCELOT_STANDALONE_PVID is statically added to the VLAN table
during ocelot_vlan_init() and never removed afterwards, calling
ocelot_add_vlan_unaware_pvid() for it is not intended and does not serve
any purpose.
Fix the issue by avoiding the call to ocelot_add_vlan_unaware_pvid(vid=0)
when we're resetting VLAN awareness after leaving the bridge, to become
a standalone port.
Fixes: 54c3198460 ("net: mscc: ocelot: enforce FDB isolation when VLAN-unaware")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both the felix DSA driver and ocelot switchdev driver declare
dev->features & NETIF_F_HW_VLAN_CTAG_FILTER under certain circumstances*,
so the 8021q module will add VID 0 to our RX filter when the port goes
up, to ensure 802.1p traffic is not dropped.
We treat VID 0 as a special value (OCELOT_STANDALONE_PVID) which
deliberately does not have a struct ocelot_bridge_vlan associated with
it. Instead, this gets programmed to the VLAN table in ocelot_vlan_init().
If we allow external calls to modify VID 0, we reach the following
situation:
# ip link add br0 type bridge vlan_filtering 1 && ip link set br0 up
# ip link set swp0 master br0
# ip link set swp0 up # this adds VID 0 to ocelot->vlans with untagged=false
bridge vlan
port vlan-id
swp0 1 PVID Egress Untagged # the bridge also adds VID 1
br0 1 PVID Egress Untagged
# bridge vlan add dev swp0 vid 100 untagged
Error: mscc_ocelot_switch_lib: Port with egress-tagged VLANs cannot have more than one egress-untagged (native) VLAN.
This configuration should have been accepted, because
ocelot_port_manage_port_tag() should select OCELOT_PORT_TAG_NATIVE.
Yet it isn't, because we have an entry in ocelot->vlans which says
VID 0 should be egress-tagged, something the hardware can't do.
Fix this by suppressing additions/deletions on VID 0 and managing this
VLAN exclusively using OCELOT_STANDALONE_PVID.
*DSA toggles it when the port becomes VLAN-aware by joining a VLAN-aware
bridge. Ocelot declares it unconditionally for some reason.
Fixes: 54c3198460 ("net: mscc: ocelot: enforce FDB isolation when VLAN-unaware")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lan966x->ports[] array has lan966x->num_phys_ports elements. These
are assigned in lan966x_probe(). That means the > comparison should be
changed to >=.
The first off by one check is harmless but the second one could lead to
an out of bounds access and a crash.
Fixes: 5ccd66e01c ("net: lan966x: add support for interrupts from analyzer")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In one of the error paths of the device_for_each_child_node() loop
in hns_mac_init, add missing call to fwnode_handle_put.
Signed-off-by: Peng Wu <wupeng58@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, there are some querying mailboxes sent from VF to PF,
and VF will wait the PF's handling result. For mailbox
HCLGE_MBX_GET_QID_IN_PF and HCLGE_MBX_GET_RSS_KEY, it may fail
when the input parameter is invalid, but the prototype of their
handler function is void. In this case, PF always return success
to VF, which may cause the VF get incorrect result.
Fixes it by adding return value for these function.
Fixes: 63b1279d99 ("net: hns3: check queue id range before using")
Fixes: 532cfc0df1 ("net: hns3: add a check for index in hclge_get_rss_key()")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add validity check for message data length in function
hclge_send_mbx_msg(), avoid unexpected overflow.
Fixes: dde1a86e93 ("net: hns3: Add mailbox support to PF driver")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, function hclge_get_ring_chain_from_mbx will return -ENOMEM if
ring_num is bigger than HCLGE_MBX_MAX_RING_CHAIN_PARAM_NUM. It is better to
return -EINVAL for the invalid parameter case.
So this patch fixes it by return -EINVAL in this abnormal branch.
Fixes: 5d02a58dae ("net: hns3: fix for buffer overflow smatch warning")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comments in function hclge_comm_tqps_update_stats is not right,
so fix it.
Fixes: 287db5c40d ("net: hns3: create new set of common tqp stats APIs for PF and VF reuse")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For debugfs node rx/tx_queue_info and rx/tx_bd_info, their output info is
aligned to the right, it's not aligned with output of other debugfs node,
so uniform their output info.
Fixes: 907676b130 ("net: hns3: use tx bounce buffer for small packets")
Fixes: e44c495d95 ("net: hns3: refactor queue info of debugfs")
Fixes: 77e9184869 ("net: hns3: refactor dump bd info of debugfs")
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If failed to register netdev, it needs to clear INITED state and stop
client in case of cause problem when concurrency with uninitialized
process of driver.
Fixes: a289a7e5c1 ("net: hns3: put off calling register_netdev() until client initialize complete")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I made a mistake with the commit a6aaa00324 ("net: ethernet: stmmac:
fix altr_tse_pcs function when using a fixed-link"). I should have
tested against both scenario of having a SGMII interface and one
without.
Without the SGMII PCS TSE adpater, the sgmii_adapter_base address is
NULL, thus a write to this address will fail.
Cc: stable@vger.kernel.org
Fixes: a6aaa00324 ("net: ethernet: stmmac: fix altr_tse_pcs function when using a fixed-link")
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Link: https://lore.kernel.org/r/20220420152345.27415-1-dinguyen@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The init_systime() may be invoked in atomic state. We have observed the
following call trace when running "phc_ctl /dev/ptp0 set" on a Intel
Agilex board.
BUG: sleeping function called from invalid context at drivers/net/ethernet/stmicro/stmmac/stmmac_hwtstamp.c:74
in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 381, name: phc_ctl
preempt_count: 1, expected: 0
RCU nest depth: 0, expected: 0
Preemption disabled at:
[<ffff80000892ef78>] stmmac_set_time+0x34/0x8c
CPU: 2 PID: 381 Comm: phc_ctl Not tainted 5.18.0-rc2-next-20220414-yocto-standard+ #567
Hardware name: SoCFPGA Agilex SoCDK (DT)
Call trace:
dump_backtrace.part.0+0xc4/0xd0
show_stack+0x24/0x40
dump_stack_lvl+0x7c/0xa0
dump_stack+0x18/0x34
__might_resched+0x154/0x1c0
__might_sleep+0x58/0x90
init_systime+0x78/0x120
stmmac_set_time+0x64/0x8c
ptp_clock_settime+0x60/0x9c
pc_clock_settime+0x6c/0xc0
__arm64_sys_clock_settime+0x88/0xf0
invoke_syscall+0x5c/0x130
el0_svc_common.constprop.0+0x4c/0x100
do_el0_svc+0x7c/0xa0
el0_svc+0x58/0xcc
el0t_64_sync_handler+0xa4/0x130
el0t_64_sync+0x18c/0x190
So we should use readl_poll_timeout_atomic() here instead of
readl_poll_timeout().
Also adjust the delay time to 10us to fix a "__bad_udelay" build error
reported by "kernel test robot <lkp@intel.com>". I have tested this on
Intel Agilex and NXP S32G boards, there is no delay needed at all.
So the 10us delay should be long enough for most cases.
Fixes: ff8ed73786 ("net: stmmac: use readl_poll_timeout() function in init_systime()")
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the user runs:
bridge link set dev $br_port mcast_flood on
this command should affect not only L2 multicast, but also IPv4 and IPv6
multicast.
In the Ocelot switch, unknown multicast gets flooded according to
different PGIDs according to its type, and PGID_MC only handles L2
multicast. Therefore, by leaving PGID_MCIPV4 and PGID_MCIPV6 at their
default value of 0, unknown IP multicast traffic is never flooded.
Fixes: 421741ea56 ("net: mscc: ocelot: offload bridge port flags to device")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220415151950.219660-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This will reset deeply on freeze and thaw instead of suspend and
resume and prevent null pointer dereferences of the uninitialized ring
0 buffer while thawing.
The impact is an indefinitely hanging kernel. You can't switch
consoles after this and the only possible user interaction is SysRq.
BUG: kernel NULL pointer dereference
RIP: 0010:aq_ring_rx_fill+0xcf/0x210 [atlantic]
aq_vec_init+0x85/0xe0 [atlantic]
aq_nic_init+0xf7/0x1d0 [atlantic]
atl_resume_common+0x4f/0x100 [atlantic]
pci_pm_thaw+0x42/0xa0
resolves in aq_ring.o to
```
0000000000000ae0 <aq_ring_rx_fill>:
{
/* ... */
baf: 48 8b 43 08 mov 0x8(%rbx),%rax
buff->flags = 0U; /* buff is NULL */
```
The bug has been present since the introduction of the new pm code in
8aaa112a57 ("net: atlantic: refactoring pm logic") and was hidden
until 8ce8427169 ("net: atlantic: changes for multi-TC support"),
which refactored the aq_vec_{free,alloc} functions into
aq_vec_{,ring}_{free,alloc}, but is technically not wrong. The
original functions just always reinitialized the buffers on S3/S4. If
the interface is down before freezing, the bug does not occur. It does
not matter, whether the initrd contains and loads the module before
thawing.
So the fix is to invert the boolean parameter deep in all pm function
calls, which was clearly intended to be set like that.
First report was on Github [1], which you have to guess from the
resume logs in the posted dmesg snippet. Recently I posted one on
Bugzilla [2], since I did not have an AQC device so far.
#regzbot introduced: 8ce8427169
#regzbot from: koo5 <kolman.jindrich@gmail.com>
#regzbot monitor: https://github.com/Aquantia/AQtion/issues/32
Fixes: 8aaa112a57 ("net: atlantic: refactoring pm logic")
Link: https://github.com/Aquantia/AQtion/issues/32 [1]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215798 [2]
Cc: stable@vger.kernel.org
Reported-by: koo5 <kolman.jindrich@gmail.com>
Signed-off-by: Manuel Ullmann <labre@posteo.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido reported that the commit referenced in the Fixes tag broke
a gre use case with dummy devices. Add a check to ip_tunnel_init_flow
to see if the oif is an l3mdev port and if so set the oif to 0 to
avoid the oif comparison in fib_lookup_good_nhc.
Fixes: 40867d74c3 ("net: Add l3mdev index to flow struct and avoid oif reset for port devices")
Reported-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-04-13
This series contains updates to igc and e1000e drivers.
Sasha removes waiting for hardware semaphore as it could cause an
infinite loop and changes usleep_range() calls done under atomic
context to udelay() for igc. For e1000e, he changes some variables from
u16 to u32 to prevent possible overflow of values.
Vinicius disables PTM when going to suspend as it is causing hang issues
on some platforms for igc.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
e1000e: Fix possible overflow in LTR decoding
igc: Fix suspending when PTM is active
igc: Fix BUG: scheduling while atomic
igc: Fix infinite loop in release_swfw_sync
====================
Link: https://lore.kernel.org/r/20220413170814.2066855-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The displayed list of Ethernet devices in make menuconfig
has gotten out of order. This is mostly due to changes in vendor
names etc, but also because of new Microsoft entry in wrong place.
This restores so that the display is in order even if the names
of the sub directories are not.
Fixes: ca9c54d2d6 ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)")
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A memory chunk was allocated for orom_data in ice_get_orom_civd_data()
by vzmalloc(). But when ice_read_flash_module() fails, the allocated
memory is not freed, which will lead to a memory leak.
We can fix it by freeing the orom_data when ce_read_flash_module() fails.
Fixes: af18d8866c ("ice: reduce time to read Option ROM CIVD data")
Signed-off-by: Jianglei Nie <niejianglei2021@163.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently for !CONFIG_NET_SWITCHDEV kernel builds it is not possible to
create VFs properly as call to ice_eswitch_configure() returns
-EOPNOTSUPP for us. This is because CONFIG_ICE_SWITCHDEV depends on
CONFIG_NET_SWITCHDEV.
Change the ice_eswitch_configure() implementation for
!CONFIG_ICE_SWITCHDEV to return 0 instead -EOPNOTSUPP and let
ice_ena_vfs() finish its work properly.
CC: Grzegorz Nitka <grzegorz.nitka@intel.com>
Fixes: 1a1c40df2e ("ice: set and release switchdev environment")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
__ice_alloc_rx_bufs_zc() checks if a number of the descriptors to be
allocated would cause the ring wrap. In that case, driver will issue two
calls to xsk_buff_alloc_batch() - one that will fill the ring up to the
end and the second one that will start with filling descriptors from the
beginning of the ring.
ice_fill_rx_descs() is a wrapper for taking care of what
xsk_buff_alloc_batch() gave back to the driver. It works in a best
effort approach, so for example when driver asks for 64 buffers,
ice_fill_rx_descs() could assign only 32. Such case needs to be checked
when ring is being filled up to the end, because in that situation ntu
might not reached the end of the ring.
Fix the ring wrap by checking if nb_buffs_extra has the expected value.
If not, bump ntu and go directly to tail update.
Fixes: 3876ff525d ("ice: xsk: Handle SW XDP ring wrap and bump tail more often")
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Shwetha Nagaraju <Shwetha.nagaraju@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When we decode the latency and the max_latency, u16 value may not fit
the required size and could lead to the wrong LTR representation.
Scaling is represented as:
scale 0 - 1 (2^(5*0)) = 2^0
scale 1 - 32 (2^(5 *1))= 2^5
scale 2 - 1024 (2^(5 *2)) =2^10
scale 3 - 32768 (2^(5 *3)) =2^15
scale 4 - 1048576 (2^(5 *4)) = 2^20
scale 5 - 33554432 (2^(5 *4)) = 2^25
scale 4 and scale 5 required 20 and 25 bits respectively.
scale 6 reserved.
Replace the u16 type with the u32 type and allow corrected LTR
representation.
Cc: stable@vger.kernel.org
Fixes: 44a13a5d99 ("e1000e: Fix the max snoop/no-snoop latency for 10M")
Reported-by: James Hutchinson <jahutchinson99@googlemail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215689
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Tested-by: James Hutchinson <jahutchinson99@googlemail.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Some mainboard/CPU combinations, in particular, Alder Lake-S with a
W680 mainboard, have shown problems (system hangs usually, no kernel
logs) with suspend/resume when PCIe PTM is enabled and active. In some
cases, it could be reproduced when removing the igc module.
The best we can do is to stop PTM dialogs from the downstream/device
side before the interface is brought down. PCIe PTM will be re-enabled
when the interface is being brought up.
Fixes: a90ec84837 ("igc: Add support for PTP getcrosststamp()")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
An infinite loop may occur if we fail to acquire the HW semaphore,
which is needed for resource release.
This will typically happen if the hardware is surprise-removed.
At this stage there is nothing to do, except log an error and quit.
Fixes: c0071c7aa5 ("igc: Add HW initialization code")
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
AST2600 MAC register 0x58 is writable only when the MAC clock is
enabled. Usually, the MAC clock is enabled by the bootloader so
register 0x58 is set normally when the bootloader is involved. To make
ast2600 ftgmac100 work without the bootloader, postpone the register
write until the clock is ready.
Fixes: 137d23cea1 ("net: ftgmac100: Fix Aspeed ast2600 TX hang issue")
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when getting a new MAC is learn, the HW generates an
interrupt. So then the SW will check the new entry and checks if it
arrived on a correct port. If it didn't just generate a warning.
But this could still crash the system. Therefore stop processing that
entry when an issue is seen.
Fixes: 5ccd66e01c ("net: lan966x: add support for interrupts from analyzer")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On lan966x it is not allowed to have foreign interfaces under a bridge
which already contains lan966x ports. So when a port leaves the bridge
it would call switchdev_bridge_port_unoffload which eventually will
notify the other ports that bridge left the vlan group but that is not
true because the bridge is still part of the vlan group.
Therefore when a port leaves the bridge, stop generating replays because
already the HW cleared after itself and the other ports don't need to do
anything else.
Fixes: cf2f60897e ("net: lan966x: Add support to offload the forwarding.")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In case an IGMP frame has a vlan tag, then the function
lan966x_hw_offload couldn't figure out that is a IGMP frame. Therefore
the SW thinks that the frame was already forward by the HW which is not
true.
Extend lan966x_hw_offload to pop the vlan tag if are any and then check
for IGMP frames.
Fixes: 47aeea0d57 ("net: lan966x: Implement the callback SWITCHDEV_ATTR_ID_BRIDGE_MC_DISABLED ")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The clk_per_cfg register represents the value added to the system clock
for each clock cycle. The issue is that the default value is wrong,
meaning that in case the DUT was a grandmaster then everone in the
network was too slow. In case there was a grandmaster, then there is no
issue because the DUT will configure clk_per_cfg register based on the
master frequency.
Fixes: d096459494 ("net: lan966x: Add support for ptp clocks")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-04-08
Alexander fixes a use after free issue with aRFS for ice driver.
Mateusz reverts a commit that introduced issues related to device
resets for iavf driver.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
Revert "iavf: Fix deadlock occurrence during resetting VF interface"
ice: arfs: fix use-after-free when freeing @rx_cpu_rmap
====================
Link: https://lore.kernel.org/r/20220408163411.2415552-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
commit 4298388574 ("net: macb: restart tx after tx used bit read")
added support for restarting transmission. Restarting tx does not work
in case controller asserts TXUBR interrupt and TQBP is already at the end
of the tx queue. In that situation, restarting tx will immediately cause
assertion of another TXUBR interrupt. The driver will end up in an infinite
interrupt loop which it cannot break out of.
For cases where TQBP is at the end of the tx queue, instead
only clear TX_USED interrupt. As more data gets pushed to the queue,
transmission will resume.
This issue was observed on a Xilinx Zynq-7000 based board.
During stress test of the network interface,
driver would get stuck on interrupt loop within seconds or minutes
causing CPU to stall.
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220407161659.14532-1-tomas.melin@vaisala.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Both of of_get_parent() and of_parse_phandle() return node pointer with
refcount incremented, use of_node_put() on it to decrease refcount
when done.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Lv Ruyi <lv.ruyi@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using a fixed-link, the altr_tse_pcs driver crashes
due to null-pointer dereference as no phy_device is provided to
tse_pcs_fix_mac_speed function. Fix this by adding a check for
phy_dev before calling the tse_pcs_fix_mac_speed() function.
Also clean up the tse_pcs_fix_mac_speed function a bit. There is
no need to check for splitter_base and sgmii_adapter_base
because the driver will fail if these 2 variables are not
derived from the device tree.
Fixes: fb3bbdb859 ("net: ethernet: Add TSE PCS support to dwmac-socfpga")
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change caused a regression with resetting while changing network
namespaces. By clearing the IFF_UP flag, the kernel now thinks it has
fully closed the device.
This reverts commit 0cc318d2e8.
Fixes: 0cc318d2e8 ("iavf: Fix deadlock occurrence during resetting VF interface")
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The CI testing bots triggered the following splat:
[ 718.203054] BUG: KASAN: use-after-free in free_irq_cpu_rmap+0x53/0x80
[ 718.206349] Read of size 4 at addr ffff8881bd127e00 by task sh/20834
[ 718.212852] CPU: 28 PID: 20834 Comm: sh Kdump: loaded Tainted: G S W IOE 5.17.0-rc8_nextqueue-devqueue-02643-g23f3121aca93 #1
[ 718.219695] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.02.01.0012.070720200218 07/07/2020
[ 718.223418] Call Trace:
[ 718.227139]
[ 718.230783] dump_stack_lvl+0x33/0x42
[ 718.234431] print_address_description.constprop.9+0x21/0x170
[ 718.238177] ? free_irq_cpu_rmap+0x53/0x80
[ 718.241885] ? free_irq_cpu_rmap+0x53/0x80
[ 718.245539] kasan_report.cold.18+0x7f/0x11b
[ 718.249197] ? free_irq_cpu_rmap+0x53/0x80
[ 718.252852] free_irq_cpu_rmap+0x53/0x80
[ 718.256471] ice_free_cpu_rx_rmap.part.11+0x37/0x50 [ice]
[ 718.260174] ice_remove_arfs+0x5f/0x70 [ice]
[ 718.263810] ice_rebuild_arfs+0x3b/0x70 [ice]
[ 718.267419] ice_rebuild+0x39c/0xb60 [ice]
[ 718.270974] ? asm_sysvec_apic_timer_interrupt+0x12/0x20
[ 718.274472] ? ice_init_phy_user_cfg+0x360/0x360 [ice]
[ 718.278033] ? delay_tsc+0x4a/0xb0
[ 718.281513] ? preempt_count_sub+0x14/0xc0
[ 718.284984] ? delay_tsc+0x8f/0xb0
[ 718.288463] ice_do_reset+0x92/0xf0 [ice]
[ 718.292014] ice_pci_err_resume+0x91/0xf0 [ice]
[ 718.295561] pci_reset_function+0x53/0x80
<...>
[ 718.393035] Allocated by task 690:
[ 718.433497] Freed by task 20834:
[ 718.495688] Last potentially related work creation:
[ 718.568966] The buggy address belongs to the object at ffff8881bd127e00
which belongs to the cache kmalloc-96 of size 96
[ 718.574085] The buggy address is located 0 bytes inside of
96-byte region [ffff8881bd127e00, ffff8881bd127e60)
[ 718.579265] The buggy address belongs to the page:
[ 718.598905] Memory state around the buggy address:
[ 718.601809] ffff8881bd127d00: fa fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
[ 718.604796] ffff8881bd127d80: 00 00 00 00 00 00 00 00 00 00 fc fc fc fc fc fc
[ 718.607794] >ffff8881bd127e00: fa fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
[ 718.610811] ^
[ 718.613819] ffff8881bd127e80: 00 00 00 00 00 00 00 00 00 00 00 00 fc fc fc fc
[ 718.617107] ffff8881bd127f00: fa fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
This is due to that free_irq_cpu_rmap() is always being called
*after* (devm_)free_irq() and thus it tries to work with IRQ descs
already freed. For example, on device reset the driver frees the
rmap right before allocating a new one (the splat above).
Make rmap creation and freeing function symmetrical with
{request,free}_irq() calls i.e. do that on ifup/ifdown instead
of device probe/remove/resume. These operations can be performed
independently from the actual device aRFS configuration.
Also, make sure ice_vsi_free_irq() clears IRQ affinity notifiers
only when aRFS is disabled -- otherwise, CPU rmap sets and clears
its own and they must not be touched manually.
Fixes: 28bf26724f ("ice: Implement aRFS")
Co-developed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Tested-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
