ASoC: Fixes for v5.14
Quite a lot of fixes here, the biggest set being for the cs42l42 driver
which is reasonably old but has seen a sudden uptick in activity.
There's also some fixes for correctly referencing PCM buffer addresses
and the removal of some driver-local bodges that had been done for the
lack of prefix handling in DAPM which were broken by the core handling
that as expected.
I2S always has two LRCLK phases and both CH1 and CH2 of the RX
must be enabled (corresponding to the low and high phases of LRCLK.)
The selection of the valid data channels is done by setting the DAC
CHA_SEL and CHB_SEL. CHA_SEL is always the first (left) channel,
CHB_SEL depends on the number of active channels.
Previously for mono ASP CH2 was not enabled, the result was playing
mono data would not produce any audio output.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 621d65f3b8 ("ASoC: cs42l42: Provide finer control on playback path")
Link: https://lore.kernel.org/r/20210805161111.10410-4-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The lowest valid SCLK corresponds to 44.1 kHz at 16-bit. Sample
rates less than this would produce SCLK below the minimum when using
a normal I2S frame. A constraint must be applied to prevent this.
The constraint is not applied if the machine driver sets SCLK, to
allow setups where the host generates additional bits per LRCLK
phase to increase the SCLK frequency. In these cases the machine
driver would always have to inform this driver of the actual SCLK,
and it must select a legal SCLK.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210805161111.10410-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Both SCLK and PLL clocks must be running to drive the glitch-free mux
behind MCLK_SRC_SEL and complete the switchover.
This patch moves the writing of MCLK_SRC_SEL to when the PLL is started
and stopped, so that it only transitions while the PLL is running.
The unconditional write MCLK_SRC_SEL=0 in cs42l42_mute_stream() is safe
because if the PLL is not running MCLK_SRC_SEL is already 0.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 43fc357199 ("ASoC: cs42l42: Set clock source for both ways of stream")
Link: https://lore.kernel.org/r/20210805161111.10410-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver was defining two ALSA controls that both change the same
register field for the wind noise filter corner frequency. The filter
response has two corners, at different frequencies, and the duplicate
controls most likely were an attempt to be able to set the value using
either of the frequencies.
However, having two controls changing the same field can be problematic
and it is unnecessary. Both frequencies are related to each other so
setting one implies exactly what the other would be.
Removing a control affects user-side code, but there is currently no
known use of the removed control so it would be best to remove it now
before it becomes a problem.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2c394ca796 ("ASoC: Add support for CS42L42 codec")
Link: https://lore.kernel.org/r/20210803160834.9005-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The tlv320aic31xx driver relies on regcache_sync() to restore the register
contents after going to _BIAS_OFF, for example during system suspend. This
does not work for the jack detection configuration since that is configured
via the same register that status is read back from so the register is
volatile and not cached. This can also cause issues during init if the jack
detection ends up getting set up before the CODEC is initially brought out
of _BIAS_OFF, we will reset the CODEC and resync the cache as part of that
process.
Fix this by explicitly reapplying the jack detection configuration after
resyncing the register cache during power on.
This issue was found by an engineer working off-list on a product
kernel, I just wrote up the upstream fix.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210723180200.25105-1-broonie@kernel.org
Cc: stable@vger.kernel.org
The TAS2505/TAS2521 does support only three processing block options, unlike
TLV320AIC32x4 which supports 25. This is documented in TI slau472 2.5.1.2
Processing Blocks and Page 0 / Register 60: DAC Instruction Set - 0x00 / 0x3C.
Limit the Processing Blocks maximum value to 3 on TAS2505/TAS2521 and select
processing block PRB_P1 always, because for the configuration of teh codec
implemented in this driver, this is the best quality option.
Fixes: b4525b6196 ("ASoC: tlv320aic32x4: add support for TAS2505")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Claudius Heine <ch@denx.de>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210720200348.182139-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
With SND_SOC_ALL_CODECS=y and SND_SOC_WCD938X_SDW=m, there is a link
error from a reverse dependency, since the built-in codec driver calls
into the modular soundwire back-end:
x86_64-linux-ld: sound/soc/codecs/wcd938x.o: in function `wcd938x_codec_free':
wcd938x.c:(.text+0x2c0): undefined reference to `wcd938x_sdw_free'
x86_64-linux-ld: sound/soc/codecs/wcd938x.o: in function `wcd938x_codec_hw_params':
wcd938x.c:(.text+0x2f6): undefined reference to `wcd938x_sdw_hw_params'
x86_64-linux-ld: sound/soc/codecs/wcd938x.o: in function `wcd938x_codec_set_sdw_stream':
wcd938x.c:(.text+0x332): undefined reference to `wcd938x_sdw_set_sdw_stream'
x86_64-linux-ld: sound/soc/codecs/wcd938x.o: in function `wcd938x_tx_swr_ctrl':
wcd938x.c:(.text+0x23de): undefined reference to `wcd938x_swr_get_current_bank'
x86_64-linux-ld: sound/soc/codecs/wcd938x.o: in function `wcd938x_bind':
wcd938x.c:(.text+0x2579): undefined reference to `wcd938x_sdw_device_get'
x86_64-linux-ld: wcd938x.c:(.text+0x25a1): undefined reference to `wcd938x_sdw_device_get'
x86_64-linux-ld: wcd938x.c:(.text+0x262a): undefined reference to `__devm_regmap_init_sdw'
Work around this using two small hacks: An added Kconfig dependency
prevents the main driver from being built-in when soundwire support
itself is a loadable module to allow calling devm_regmap_init_sdw(),
and a Makefile trick links the wcd938x-sdw backend as built-in
if needed to solve the dependency between the two modules.
Fixes: 0454422288 ("ASoC: codecs: wcd938x: add audio routing and Kconfig")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210721150510.1837221-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC: Fixes for v5.14
A collection of fixes for ASoC that have come in since the merge window,
all driver specific. There is a new core feature added for reversing
the order of operations when shutting down, this is needed to fix a bug
with the AMD Stonyridge platform, and we also tweak the Kconfig to make
the SSM2518 driver user selectable so it can be used with generic cards
but that requires no actual code changes.
currenlty wcd938x has only soundwire interface and depends on
symbols from wcd938x soundwire module, so make this dependency
explicit in Kconfig
Without this one of the randconfig endup setting
CONFIG_SND_SOC_WCD938X=y
CONFIG_SND_SOC_WCD938X_SDW=m
resulting in some undefined reference to wcd938x_sdw* symbols.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 0454422288 ("ASoC: codecs: wcd938x: add audio routing and Kconfig")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210713140417.23693-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The ALC5631 does not like multi-write accesses, avoid them. This fixes:
rt5631 4-001a: Unable to sync registers 0x3a-0x3c. -121
errors on resume from suspend (and all registers after the registers in
the error not being synced).
Inspired by commit 2d30e9494f ("ASoC: rt5651: Fix regcache sync errors
on resume") from Hans de Geode, which fixed the same errors on ALC5651.
Signed-off-by: Maxim Schwalm <maxim.schwalm@gmail.com>
Link: https://lore.kernel.org/r/20210712005011.28536-1-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the tlv320aic31xx driver has regulator support but does not
enable the regulators during probe, deferring this until something causes
ASoC to make the card active. It does put the device into cache only mode
but only when the component level probe is called, however if interrupts
are in use the driver will access the regmap before then which if the
regulators are not powered on would cause I/O problems.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210707160234.16253-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
None of the TAS2505 outputs are stereo, do not pretend they are by
implementing them using SOC*DOUBLE* macros referencing the same
register twice, use SOC*SINGLE* instead. Fix volume ranges and mute
control for the codec according to datasheet.
Fixes: b4525b6196 ("ASoC: tlv320aic32x4: add support for TAS2505")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Claudius Heine <ch@denx.de>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210708091255.56502-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull tty / serial updates from Greg KH:
"Here is the big set of tty and serial driver patches for 5.14-rc1.
A bit more than normal, but nothing major, lots of cleanups.
Highlights are:
- lots of tty api cleanups and mxser driver cleanups from Jiri
- build warning fixes
- various serial driver updates
- coding style cleanups
- various tty driver minor fixes and updates
- removal of broken and disable r3964 line discipline (finally!)
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (227 commits)
serial: mvebu-uart: remove unused member nb from struct mvebu_uart
arm64: dts: marvell: armada-37xx: Fix reg for standard variant of UART
dt-bindings: mvebu-uart: fix documentation
serial: mvebu-uart: correctly calculate minimal possible baudrate
serial: mvebu-uart: do not allow changing baudrate when uartclk is not available
serial: mvebu-uart: fix calculation of clock divisor
tty: make linux/tty_flip.h self-contained
serial: Prefer unsigned int to bare use of unsigned
serial: 8250: 8250_omap: Fix possible interrupt storm on K3 SoCs
serial: qcom_geni_serial: use DT aliases according to DT bindings
Revert "tty: serial: Add UART driver for Cortina-Access platform"
tty: serial: Add UART driver for Cortina-Access platform
MAINTAINERS: add me back as mxser maintainer
mxser: Documentation, fix typos
mxser: Documentation, make the docs up-to-date
mxser: Documentation, remove traces of callout device
mxser: introduce mxser_16550A_or_MUST helper
mxser: rename flags to old_speed in mxser_set_serial_info
mxser: use port variable in mxser_set_serial_info
mxser: access info->MCR under info->slock
...
Pull driver core changes from Greg KH:
"Here is the small set of driver core and debugfs updates for 5.14-rc1.
Included in here are:
- debugfs api cleanups (touched some drivers)
- devres updates
- tiny driver core updates and tweaks
Nothing major in here at all, and all have been in linux-next for a
while with no reported issues"
* tag 'driver-core-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (27 commits)
docs: ABI: testing: sysfs-firmware-memmap: add some memmap types.
devres: Enable trace events
devres: No need to call remove_nodes() when there none present
devres: Use list_for_each_safe_from() in remove_nodes()
devres: Make locking straight forward in release_nodes()
kernfs: move revalidate to be near lookup
drivers/base: Constify static attribute_group structs
firmware_loader: remove unneeded 'comma' macro
devcoredump: remove contact information
driver core: Drop helper devm_platform_ioremap_resource_wc()
component: Rename 'dev' to 'parent'
component: Drop 'dev' argument to component_match_realloc()
device property: Don't check for NULL twice in the loops
driver core: auxiliary bus: Fix typo in the docs
drivers/base/node.c: make CACHE_ATTR define static DEVICE_ATTR_RO
debugfs: remove return value of debugfs_create_ulong()
debugfs: remove return value of debugfs_create_bool()
scsi: snic: debugfs: remove local storage of debugfs files
b43: don't save dentries for debugfs
b43legacy: don't save dentries for debugfs
...
Pull mfd updates from Lee Jones:
"Core Frameworks:
- Fix Software Node clean-up code
New Drivers:
- Add support for MediaTek MT6359 PMIC
- Add support for Qualcomm PM8008 PMIC
- Add support for Richtek RT4831
New Device Support:
- Add support for Audio CODECs to Rockchip RK817
- Add support for Alder Lake-M to Intel LPSS PCI
- Add support for Periph Device Charge to ChromeOS EC
New Functionality:
- Provide additional IRQs for wcd934x
- Add optional Reset functionality to lp87565
Fix-ups:
- Namespacing & visibility fixes to lp87565
- Differentiate between Power and Home key IRQs in mt6358
- Export I2C device tables in da9052-i2c, stmpe-i2c
- Adapt IRQ flags in max8907, rn5t61, max8907
- Make some functions/devices optional in axp20x, cros_ec_dev
- Explicitly include used header files in ioc3
- Remove superfluous lines in MAINTAINERS, sec-core, st,stm32-timers
- Resolve Kerneldoc issues in omap-usb-host, omap-usb-tll, si476x-cmd, si476x-i2c
- Convert arizona-core to a module
- Copyright changes in hi655x-pmic
- Drop support for board file initialisation in sec-core
- Trivial spelling, whitespace etc updates in lp87565, si476x-cmd,
mt6360-core, wm831x-core, twl-core, db8500-prcmu
- Simplify various implementations of wcd934x, mt6360-core, max8997,
max8998, da9052-i2c, da9062-core, sec-core,
- Device Tree binding changes in google,cros-ec,
richtek,rt4831-backlight, db8500-prcmu, qcom,pm8008, qcom,spmi-pmic
- Use provided APIs to simplify t7l66xb, as3722, da9055-core,
tps80031, 88pm800, 88pm805, asic3, sun6i-prcm, wm831x-core,
wm831x-otp, ucb1x00-assabet, timberdale, sm501, pcf50633-core,
kempld-core, janz-cmodio, intel_soc_pmic_bxtwc, ab8500-core
Bug Fixes:
- Fix unused variable warning in rk817_codec
- Fix regulator voltage configuration in rohm-bd71828
- Fix ongoing freeing of regmap_config 'name' issue in syscon
- Fix error handling path in da9063-i2c
- Fix Kconfig issues in MFD_MP2629
- Fix DMA mask warnings in motorola-cpcap"
* tag 'mfd-next-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (83 commits)
mfd: cros_ec: Add peripheral device charger
mfd: max8907: Remove IRQF_NO_AUTOEN flag
mfd: ab8500-core: Use DEVICE_ATTR_RO/RW macro
mfd: intel_soc_pmic_bxtwc: Use DEVICE_ATTR_ADMIN_RW macro
mfd: janz-cmodio: Use DEVICE_ATTR_RO macro
mfd: kempld-core: Use DEVICE_ATTR_RO macro
mfd: pcf50633: Use DEVICE_ATTR_ADMIN_RO macro
mfd: sm501: Use DEVICE_ATTR_RO macro
mfd: timberdale: Use DEVICE_ATTR_RO macro
mfd: ucb1x00-assabet: Use DEVICE_ATTR_RO macro
mfd: wm831x: Use DEVICE_ATTR_RO macro
mfd: wm831x: Use DEFINE_RES_IRQ_NAMED() and DEFINE_RES_IRQ() to simplify code
dt-bindings: mfd: stm32-timers: Remove #address/size cells from required properties
mfd: sun6i-prcm: Use DEFINE_RES_MEM() to simplify code
mfd: asic3: Use DEFINE_RES_MEM() and DEFINE_RES_IRQ() to simplify code
mfd: 88pm805: Use DEFINE_RES_IRQ_NAMED() to simplify code
mfd: 88pm800: Use DEFINE_RES_IRQ_NAMED() to simplify code
mfd: tps80031: Use DEFINE_RES_IRQ() to simplify code
mfd: da9055: Use DEFINE_RES_IRQ_NAMED() to simplify code
mfd: as3722: Use DEFINE_RES_IRQ_NAMED() to simplify code
...
When wm_coeff_tlv_get was updated it was accidentally switch to the _raw
version of the helper causing it to ignore the current DSP state it
should be checking. Switch the code back to the correct helper so that
users can't read the controls when they arn't available.
Fixes: 73ecf1a673 ("ASoC: wm_adsp: Correct cache handling of new kernel control API")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210626155941.12251-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hi,
this is v2 from my patchset that add support for the TAS2505 to the tlv320aic32x4 driver.
kind regards,
Claudius
Changes from v1:
- clarified commit message of first patch, which add the type value to the struct
- removed unnecessary code to put and get speaker volume
- removed 'Gain' from 'HP Driver Playback Volume' control
- fixed rebase issues
Claudius Heine (3):
ASoC: tlv320aic32x4: add type to device private data struct
ASoC: tlv320aic32x4: add support for TAS2505
ASoC: tlv320aic32x4: dt-bindings: add TAS2505 to compatible
.../bindings/sound/tlv320aic32x4.txt | 1 +
sound/soc/codecs/tlv320aic32x4-i2c.c | 22 ++-
sound/soc/codecs/tlv320aic32x4-spi.c | 23 ++-
sound/soc/codecs/tlv320aic32x4.c | 139 +++++++++++++++++-
sound/soc/codecs/tlv320aic32x4.h | 10 ++
5 files changed, 186 insertions(+), 9 deletions(-)
base-commit: 70585216fe
--
2.32.0
While this driver can already handle different device variants, the
variant information cannot be used in the driver code and therefor
cannot have different code paths depending on the device variant.
This change adds a `type` value into the `aic32x4_priv` structure, that
contains a device variant identifier, which was set when the driver was
bound to the device.
Signed-off-by: Claudius Heine <ch@denx.de>
Link: https://lore.kernel.org/r/20210617085230.1851503-2-ch@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes below two uninitialized symbol warnings
warning:
sound/soc/codecs/wcd938x.c:2092 wcd938x_tx_swr_ctrl()
error: uninitialized symbol 'rate'
sound/soc/codecs/wcd938x.c:2189 wcd938x_tx_channel_config()
error: uninitialized symbol 'reg'.
First one my brining in check to already existing if condition and
second one by adding a default switch case to avoid any access to reg.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210621134502.19537-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
In the initial driver we cancelled deferred work, but there is still a
window of time where a new interrupt could result in new deferred work
executed after the link is disabled, leading to an IO error. While we
did not see this IO error on RT711-sdca-based platforms, the code pattern
is similar to the RT700 case where the IO error was noted, so the fix
is added for consistency.
This patch uses an 'disable_irq_lock' mutex to prevent new interrupts
from happening after the start of the system suspend. The choice of a
mutex v. a spinlock is mainly due to the time required to clear
interrupts, which requires a command to be transmitted by the
SoundWire host IP and acknowledged with an interrupt. The
'interrupt_callback' routine is also not meant to be called from an
interrupt context.
An additional 'disable_irq' flag prevents race conditions where the
status changes before the interrupts are disabled, but the workqueue
handling status changes is scheduled after the completion of the
system suspend. On resume the interrupts are re-enabled already by the
io_init routine so we only clear the flag.
The code is slightly different from the other codecs since the
interrupt callback deals with the SDCA interrupts, leading to a much
larger section that's protected by the mutex. The SoundWire interrupt
scheme requires a read after clearing a status, it's not clear from
the specifications what would happen if SDCA interrupts are disabled
in the middle of the sequence, so the entire interrupt status
read/write is kept as is, even if in the end we discard the
information.
BugLink: https://github.com/thesofproject/linux/issues/2943
Fixes: 7ad4d237e7 ('ASoC: rt711-sdca: Add RT711 SDCA vendor-specific driver')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20210614180815.153711-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In the initial driver we cancelled deferred work, but there is still a
window of time where a new interrupt could result in new deferred work
executed after the link is disabled, leading to an IO error. While we
did not see this IO error on RT5682-based platforms, the code pattern
is similar to the RT700 case where the IO error was noted, so the fix
is added for consistency.
This patch uses an 'disable_irq_lock' mutex to prevent new interrupts
from happening after the start of the system suspend. The choice of a
mutex v. a spinlock is mainly due to the time required to clear
interrupts, which requires a command to be transmitted by the
SoundWire host IP and acknowledged with an interrupt. The
'interrupt_callback' routine is also not meant to be called from an
interrupt context.
An additional 'disable_irq' flag prevents race conditions where the
status changes before the interrupts are disabled, but the workqueue
handling status changes is scheduled after the completion of the
system suspend. On resume the interrupts are re-enabled already by the
io_init routine so we only clear the flag.
The Fixes tag points to a 5.10 commit, there's no need to propagate
this change to earlier upstream versions.
BugLink: https://github.com/thesofproject/linux/issues/2943
Fixes: 4a55000722 ('ASoC: codecs: rt*.c: remove useless pointer cast')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20210614180815.153711-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In previous commits we cancelled deferred work, but there is still a
window of time where a new interrupt could result in new deferred work
executed after the link is disabled, leading to an IO error. While we
did not see this IO error on RT711-based platforms, the code pattern
is similar to the RT700 case where the IO error was noted, so the fix
is added for consistency.
This patch uses an 'disable_irq_lock' mutex to prevent new interrupts
from happening after the start of the system suspend. The choice of a
mutex v. a spinlock is mainly due to the time required to clear
interrupts, which requires a command to be transmitted by the
SoundWire host IP and acknowledged with an interrupt. The
'interrupt_callback' routine is also not meant to be called from an
interrupt context.
An additional 'disable_irq' flag prevents race conditions where the
status changes before the interrupts are disabled, but the workqueue
handling status changes is scheduled after the completion of the
system suspend. On resume the interrupts are re-enabled already by the
io_init routine so we only clear the flag.
BugLink: https://github.com/thesofproject/linux/issues/2943
Fixes: 501ef01339 ('ASoC: rt711: wait for the delayed work to finish when the system suspends')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20210614180815.153711-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In previous commits we cancelled deferred work, but there is still a
window of time where a new interrupt could result in new deferred work
executed after the link is disabled, leading to an IO error.
This patch uses an 'disable_irq_lock' mutex to prevent new interrupts
from happening after the start of the system suspend. The choice of a
mutex v. a spinlock is mainly due to the time required to clear
interrupts, which requires a command to be transmitted by the
SoundWire host IP and acknowledged with an interrupt. The
'interrupt_callback' routine is also not meant to be called from an
interrupt context.
An additional 'disable_irq' flag prevents race conditions where the
status changes before the interrupts are disabled, but the workqueue
handling status changes is scheduled after the completion of the
system suspend. On resume the interrupts are re-enabled already by the
io_init routine so we only clear the flag.
BugLink: https://github.com/thesofproject/linux/issues/2943
Fixes: 5f2df2a458 ('ASoC: rt700: wait for the delayed work to finish when the system suspends')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20210614180815.153711-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For some reason we ended up with cyclic dependency between snd_soc_wcd938x
and snd_soc_wcd938x_sdw modules.
Remove this cyclic dependency by handling them in respective modules.
Without this below error is reported during make modules_install
depmod: ERROR: Cycle detected: snd_soc_wcd938x -> snd_soc_wcd938x_sdw -> snd_soc_wcd938x
depmod: ERROR: Found 2 modules in dependency cycles!
Fixes: 0454422288 ("ASoC: codecs: wcd938x: add audio routing and Kconfig")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210615132829.23067-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
