While there's a comment pointing from dpu_intr_set to dpu_hw_intr_reg
and vice-versa, an array initializer using indices makes it so that the
indices between the enum and array cannot possibly get out of sync even
if they're accidentially ordered wrongly. It is still useful to keep
the comment to be made aware where the register offset mapping resides
while looking at dpu_hw_intr_reg.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220226194633.204501-1-marijn.suijten@somainline.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Accessing the DDI_BUF_CTL register without the port's DDI clock being
enabled (to set/clear the TypeC PHY ownership for the port) can lead to
a corrupted value read during any i915 register access right after the
DDI clock is enabled.
The root cause is the way clock synchronization works for this register,
controlled by the CHICKEN_DCPR_1 DDI_CLOCK_REG_ACCESS flag. Correctly
this flag should be cleared on ADLP (see the Bspec link below), however
after bootup the flag is set.
One easily reproducible issue is an unclaimed register access of the
PWR_WELL_CTL_DDI2 register, programmed right after DDI clock enabling to
enable the port's DDI_IO power well (see the HSDES, VLK links below).
With the correct setting above this problem can't be reproduced.
Bspec: 49189
HSDES: 18019028154
VLK: 28328, 28655
Cc: Jouni Högander <jouni.hogander@intel.com>
Cc: Arthur J Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Acked-by: Arthur J Runyan <arthur.j.runyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220323201749.288566-1-imre.deak@intel.com
SMU takes clock limits in Mhz units. socclk and fclk were
using 10 khz units in some cases. Switch to Mhz units.
Fixes higher than required SoC clocks.
Fixes: 97cf32996c ("drm/amd/pm: Removed fixed clock in auto mode DPM")
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why & How]
Make dcn315 base its clock table off dcfclk rather than fclk.
This change also adds some sanity checking to make sure an
empty pmfw table does not result in invalid dal clocks.
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Work around to try to wake unresponsive DP sinks may need to be adjusted
for certain sinks.
[How]
Add options to disable work around or adjust time spent trying to wake
unresponsive DPRX.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
comparing pwm bl values (coverted) with user brightness(converted)
levels in commit_tail leads to continuous setting of backlight via dmub
as they don't to match.
This leads overdrive in queuing of commands to DMCU that sometimes lead
to depending on load on DMCU fw:
"[drm:dc_dmub_srv_wait_idle] *ERROR* Error waiting for DMUB idle: status=3"
[How]
Store last successfully set backlight value and compare with it instead
of pwm reads which is not what we should compare with.
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Instead of exit PSR when a frontbuffer invalidation happens, we can
enable the PSR2 selective fetch continuous full frame, that will keep
the panel updated like PSR was disabled but without keeping PSR active.
So as soon as the frontbuffer flush happens we can disable the
continuous full frame and start to do selective fetches much quicker
than the path that would enable PSR, that will wait a few frames
to actually activate PSR.
Also this approach has proven to fix some glitches found in Alderlake-P
when there are a lot of invalidations happening together with page
flips.
Some may ask why it is writing to CURSURFLIVE(), it is because
that is the way that hardware team provided us to poke display to
handle PSR updates, and it is being used since display 9.
v2:
- handling possible race conditions between frontbuffer rendering and
page flips
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Cc: Khaled Almahallawy <khaled.almahallawy@intel.com>
Cc: Shawn C Lee <shawn.c.lee@intel.com>
Cc: Jouni Högander <jouni.hogander@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220405155344.47219-3-jose.souza@intel.com
Frontbuffer rendering and page flips can race with each other
and this can potentialy cause issues with PSR2 selective fetch.
And because pipe/crtc updates are time sentive we can't grab the
PSR lock after intel_pipe_update_start() and before
intel_pipe_update_end().
So here adding the lock and unlock functions and calls, the
proper PSR2 selective fetch handling will come in a separated patch.
v2:
- fixed new functions documentation
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Cc: Jouni Högander <jouni.hogander@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220405155344.47219-2-jose.souza@intel.com
Following up what was done in commit 804f468853 ("drm/i915/psr: Set
"SF Partial Frame Enable" also on full update") and also setting
partial frame enable when psr_force_hw_tracking_exit() is called.
Also as PSR2_MAN_TRK_CTL is a double buffered registers do a RMW
is not a good idea so here also setting the man_trk_ctl_enable_bit()
that is required in TGL and only doing a register write.
v2:
- not doing a rmw
v3:
- removing the inline from functions that return PSR2_MAN_TRK_CTL
bits
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Cc: Jouni Högander <jouni.hogander@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220405155344.47219-1-jose.souza@intel.com
[Why]
On resume we do link detection for all non-MST connectors.
MST is handled separately. However the condition for telling
if connector is on mst branch is not enough for mst hub case.
Link detection for mst branch link leads to mst topology reset.
That causes assert in dc_link_allocate_mst_payload()
[How]
Use link type as indicator for mst link.
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When waking from low-power states, a DP sink may remain unresponsive to
AUX transactions.
[How]
Try to toggle DPCD SET_POWER register repeatedly (up to a maximum
timeout value) until DP sink becomes responsive.
Reviewed-by: Mustapha Ghaddar <Mustapha.Ghaddar@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In init_hw() we call init_pipes() before enabling power gating.
init_pipes() tries to power gate dsc but it may fail because
required force-ons are not released yet.
As a result with dsc config the following errors observed on resume:
"REG_WAIT timeout 1us * 1000 tries - dcn20_dsc_pg_control"
"REG_WAIT timeout 1us * 1000 tries - dcn20_dpp_pg_control"
"REG_WAIT timeout 1us * 1000 tries - dcn20_hubp_pg_control"
[How]
Move enable_power_gating_plane() before init_pipes() in init_hw()
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DSC Power down code has been moved from dcn31_init_hw into init_pipes()
Need to remove it from dcn10_init_hw() as well to avoid duplicated action
on dcn1.x/2.x
[How]
Remove DSC power down code from dcn10_init_hw()
Fixes: 8fa6f4c571 ("drm/amd/display: fixed the DSC power off sequence during Driver PnP")
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Once DSC slice cannot fit pixel clock, we incorrectly
reset min slices to 0 and allow max slice to operate,
even when max slice itself cannot fit the pixel clock
properly.
[How]
Change the sequence such that we correctly determine
DSC is not possible when both min slices and max
slices cannot fit pixel clock per slice.
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Chris Park <Chris.Park@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some video card has more than one vcn instance, passing 0 to
vcn_v3_0_pause_dpg_mode is incorrect.
Error msg:
Register(1) [mmUVD_POWER_STATUS] failed to reach value
0x00000001 != 0x00000002
Reviewed-by: James Zhu <James.Zhu@amd.com>
Signed-off-by: tiancyin <tianci.yin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
For VCN FW to detect ASIC type, in order to use different mailbox registers.
V2: simplify codes and fix format issue.
Signed-off-by: Boyuan Zhang <boyuan.zhang@amd.com>
Acked-by Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
SMU takes clock limits in Mhz units. socclk and fclk were
using 10 khz units in some cases. Switch to Mhz units.
Fixes higher than required SoC clocks.
Fixes: 97cf32996c ("drm/amd/pm: Removed fixed clock in auto mode DPM")
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Make dcn315 base its clock table off dcfclk rather than fclk.
This change also adds some sanity checking to make sure an
empty pmfw table does not result in invalid dal clocks.
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Variable igp_lane_info always is 0. 0 & any value = 0 and false.
In this way, all сonditional statements will false.
The code was leftover from when the code was ported from radeon
where igp_lane_info was derived from the vbios on supported
platforms.
[update commit message - Alex]
Signed-off-by: Grigory Vasilyev <h0tc0d3@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Smatch reports these issues
si_blit_shaders.c:31:11: warning: symbol 'si_default_state'
was not declared. Should it be static?
si_blit_shaders.c:253:11: warning: symbol 'si_default_size'
was not declared. Should it be static?
Both symbols are only used in si.c. Single file symbols
should be static. So move the definition of
si_default_state and si_default_size to si_blit_shader.h
and change their storage-class-specifier to static.
Remove unneeded si_blit_shader.c
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The use of the old-style SET_RUNTIME_PM_OPS() and
SET_SYSTEM_SLEEP_PM_OPS() macros requires function definitions
to be hidden to avoid
drivers/gpu/drm/tegra/vic.c:326:12: error: 'vic_runtime_suspend' defined but not used [-Werror=unused-function]
326 | static int vic_runtime_suspend(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/tegra/vic.c:292:12: error: 'vic_runtime_resume' defined but not used [-Werror=unused-function]
292 | static int vic_runtime_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~~~
Use the new-style SYSTEM_SLEEP_PM_OPS() and RUNTIME_PM_OPS() instead.
Fixes: 1e15f5b911 ("drm/tegra: vic: Stop channel on suspend")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When the host1x syncpts status is dumped via the debugfs, syncpts that
have been allocated but not yet used are not shown and so currently it
is not possible to see all the allocated syncpts. Update the path for
dumping the syncpt status via the debugfs to show all allocated syncpts
even if they have not been used yet. Note that when the syncpt status
is dumped by the kernel itself for debugging only the active syncpt are
shown.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
atomic_flush will be called for each CRTC even if they aren't enabled.
The whole code we have there will thus run without a properly affected
channel, which can then result in all sorts of weird behaviour.
Fortunately, the DRM_PLANE_COMMIT_ACTIVE_ONLY flag will skip the CRTC
atomic_begin and atomic_flush, and the planes atomic_update, if they
aren't enabled.
Our plane atomic_update is a nop, and atomic_begin will copy the current
HVS channel to the vc4_crtc structure for the interrupt handler to
consume, but the handler won't run if the CRTC is disabled. So in the
end, it will only skip our CRTC atomic_flush, which is what we want.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/r/20220331143744.777652-7-maxime@cerno.tech
The vc4_hvs_update_dlist function mostly deals with setting up the
vblank events and setting up the dlist entry pointer to our current
active one.
We'll want to do the former separately from the vblank handling in later
patches, so let's move it to a function of its own.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/r/20220331143744.777652-6-maxime@cerno.tech
In order to get the field currently being output, the driver has been
using the display FIFO frame count in the HVS, reading a 6-bit field at
the offset 12 in the DISPSTATx register.
While that field is indeed at that location for the FIFO 1 and 2, the
one for the FIFO0 is actually in the DISPSTAT1 register, at the offset
18.
Fixes: e538092cb1 ("drm/vc4: Enable precise vblank timestamping for interlaced modes.")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/r/20220331143744.777652-3-maxime@cerno.tech
During a commit, the core clock, which feeds the HVS, needs to run at
a minimum of 500MHz.
While doing that commit, we can also change the mode to one that
requires a higher core clock, so we take the core clock rate associated
to that new state into account for that boost.
However, the old state also needs to be taken into account if it
requires a core clock higher that the new one and our 500MHz limit,
since it's still live in hardware at the beginning of our commit.
Fixes: 16e101051f ("drm/vc4: Increase the core clock based on HVS load")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/r/20220331143744.777652-2-maxime@cerno.tech
Buffer mappings used in job submissions are usually small and not
rapidly reused as opposed to framebuffers (which are usually large and
rapidly reused, for example when page-flipping between double-buffered
framebuffers). Avoid going through the mapping cache for these buffers
since the cache would also lead to leaks if nobody is ever releasing
the cache's last reference. For DRM/KMS these last references are
dropped when the framebuffers are removed and therefore no longer
needed.
While at it, also add a note about the need to explicitly remove the
final reference to the mapping in the cache.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
