We found that (at least some versions of) the sci-fw set the base clock
rate for UARTs in the MCU domain to 96 MHz instead of the expected 48 MHz,
leading to incorrect baud rates when used from Linux.
As the 8250_omap driver will query the actual clock rate from the clk
driver when clock-frequency is unset, removing the incorrect property is
sufficient to fix the baud rate.
Fixes: 8abae9389b ("arm64: dts: ti: Add support for AM642 SoC")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20220419075157.189347-1-matthias.schiffer@ew.tq-group.com
-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-04-26
This series contains updates to ice driver only.
Ivan Vecera removes races related to VF message processing by changing
mutex_trylock() call to mutex_lock() and moving additional operations
to occur under mutex.
Petr Oros increases wait time after firmware flash as current time is
not sufficient.
Jake resolves a use-after-free issue for mailbox snapshot.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Mat Martineau says:
====================
mptcp: Timeout for MP_FAIL response
When one peer sends an infinite mapping to coordinate fallback from
MPTCP to regular TCP, the other peer is expected to send a packet with
the MPTCP MP_FAIL option to acknowledge the infinite mapping. Rather
than leave the connection in some half-fallback state, this series adds
a timeout after which the infinite mapping sender will reset the
connection.
Patch 1 adds a fallback self test.
Patches 2-5 make use of the MPTCP socket's retransmit timer to reset the
MPTCP connection if no MP_FAIL was received.
Patches 6 and 7 extends the self test to check MP_FAIL-related MIBs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends chk_fail_nr to check the MP_FAIL response mibs.
Add a new argument invert for chk_fail_nr to allow it can check the
MP_FAIL TX and RX mibs from the opposite direction.
When the infinite map is received before the MP_FAIL response, the
response will be lost. A '-' can be added into fail_tx or fail_rx to
represent that MP_FAIL response TX or RX can be lost when doing the
checks.
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new msk->flags bit MPTCP_FAIL_NO_RESPONSE, then reuses
sk_timer to trigger a check if we have not received a response from the
peer after sending MP_FAIL. If the peer doesn't respond properly, reset
the subflow.
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new struct member mp_fail_response_expect in struct
mptcp_subflow_context to support MP_FAIL response. In the single subflow
with checksum error and contiguous data special case, a MP_FAIL is sent
in response to another MP_FAIL.
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mptcp_data_lock() needs to be held when manipulating the msk
retransmit_timer or the sk sk_timer. This patch adds the data
lock for the both timers.
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the single subflow test case for MP_FAIL, to test the infinite
mapping case. Use the test_linkfail value to make 128KB test files.
Add a new function reset_with_fail(), in it use 'iptables' and 'tc
action pedit' rules to produce the bit flips to trigger the checksum
failures. Set validate_checksum to enable checksums for the MP_FAIL
tests without passing the '-C' argument. Set check_invert flag to
enable the invert bytes check for the output data in check_transfer().
Instead of the file mismatch error, this test prints out the inverted
bytes.
Add a new function pedit_action_pkts() to get the numbers of the packets
edited by the tc pedit actions. Print this numbers to the output.
Also add the needed kernel configures in the selftests config file.
Suggested-by: Davide Caratti <dcaratti@redhat.com>
Co-developed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce template operation to remove code duplication.
Split spi_nor_cypress_octal_dtr_enable() in
spi_nor_cypress_octal_dtr_ena() spi_nor_cypress_octal_dtr_dis() as it no
longer made sense to try to keep everything alltogether: too many
"if (enable)" throughout the code, which made the code difficult to read.
Add debug messages in case spi_nor_read_id() fails.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-9-tudor.ambarus@microchip.com
Introduce template operation to remove code duplication.
Split spi_nor_micron_octal_dtr_enable() in spi_nor_micron_octal_dtr_en()
and spi_nor_micron_octal_dtr_dis() as it no longer made sense to try to
keep everything alltogether: too many "if (enable)" throughout the code,
which made the code difficult to follow. Add dev_dbg messages in case
spi_nor_read_id() fails.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-8-tudor.ambarus@microchip.com
Use spi_nor_read_id() core method to avoid duplication of code. Now the ID
is read on the full SPI_NOR_MAX_ID_LEN instead of
round_up(nor->info->id_len, 2), but it doesn't harm to read more ID bytes,
so the change comes with no secondary effects. dev_dbg messages in case
spi_nor_read_id() fails, will be added in a further patch after we split
the octal DTR enable/disable methods.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-6-tudor.ambarus@microchip.com
RDID is used in the core to auto detect the flash, but also by some
manufacturer drivers that contain flashes that support Octal DTR mode,
so that they can read the flash ID after the switch to Octal DTR was made
to test if the switch was successful. Introduce a core method for RDID op
to avoid code duplication.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-5-tudor.ambarus@microchip.com
Read back Status Register 1 to ensure that the written byte match the
received value and return -EIO if read back test failed.
Without this patch, spi_nor_write_16bit_sr_and_check() only check the
second half of the 16bit. It causes errors like spi_nor_sr_unlock()
return success incorrectly when spi_nor_write_16bit_sr_and_check()
doesn't write SR successfully.
Fixes: 39d1e3340c ("mtd: spi-nor: Fix clearing of QE bit on lock()/unlock()")
Signed-off-by: Chen-Tsung Hsieh <chentsung@chromium.org>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220126073227.3401275-1-chentsung@chromium.org
The pinctrl device tree binding will be converted to YAML format. Rename
the pin nodes so they end with "-pins" to match the schema.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The pinctrl device tree binding will be converted to YAML format. Rename
the pin nodes so they end with "-pins" to match the schema.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The pinctrl device tree binding will be converted to YAML format. Rename
the pin nodes so they end with "-pins" to match the schema.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
All pin groups function as gpio unless set otherwise. Therefore, remove
this unnecessary binding.
Tested on UniElec U7621-06-16M on OpenWrt.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Mux the MT7530 switch's phy4 to the SoC's gmac1 on the GB-PC1 devicetree.
This achieves 2 Gbps total bandwidth to the CPU using the second RGMII.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Fix the handling of MEM_FRAG_TX/RX SMCs when the full memory descriptor
does not fit in a single innovation of a memory sharing request.
The current implementation expects a FFA_MEM_SHARE/FFA_MEM_LEND
call to always receive a FFA_SUCCESS response, however in the
case where a full descriptor does not fit inside the partitions
TX buffer, the call can instead complete with a FFA_MEM_FRAG_RX SMC
to request the next part of the descriptor to be transmitted.
Similarly a FFA_MEM_FRAG_TX call currently only expects
FFA_MEM_FRAG_RX as a response, however once the full descriptor
has been transmitted the FFA_SUCCESS ABI will be used to indicate
successful transmission.
Update the existing code to match the expected behaviour.
Link: https://lore.kernel.org/r/20220426121219.1801601-1-marc.bonnici@arm.com
Signed-off-by: Marc Bonnici <marc.bonnici@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The decision to free kernfs_open_node object in kernfs_put_open_node can
be taken based on whether kernfs_open_node->files list is empty or not. As
far as kernfs_drain_open_files is concerned it can't overlap with
kernfs_fops_open and hence can check for ->attr.open optimistically
(if ->attr.open is NULL) or under kernfs_open_file_mutex (if it needs to
traverse the ->files list.) Thus kernfs_drain_open_files can work w/o ref
counting involved kernfs_open_node as well.
So remove ->refcnt and modify the above mentioned users accordingly.
Suggested by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Imran Khan <imran.f.khan@oracle.com>
Link: https://lore.kernel.org/r/20220324103040.584491-2-imran.f.khan@oracle.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When ACPI table includes _PLD fields for a device, create a new
directory (physical_location) in sysfs to share _PLD fields.
Currently without PLD information, when there are multiple of same
devices, it is hard to distinguish which device corresponds to which
physical device at which location. For example, when there are two Type
C connectors, it is hard to find out which connector corresponds to the
Type C port on the left panel versus the Type C port on the right panel.
With PLD information provided, we can determine which specific device at
which location is doing what.
_PLD output includes much more fields, but only generic fields are added
and exposed to sysfs, so that non-ACPI devices can also support it in
the future. The minimal generic fields needed for locating a device are
the following.
- panel
- vertical_position
- horizontal_position
- dock
- lid
Signed-off-by: Won Chung <wonchung@google.com>
Link: https://lore.kernel.org/r/20220314195458.271430-1-wonchung@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit a85a6c86c2 ("driver core: platform: Clarify that IRQ 0 is
invalid") only calls WARN() when IRQ0 is about to be returned, however
using IRQ0 is considered invalid (according to Linus) outside the arch/
code where it's used by the i8253 drivers. Many driver subsystems treat
0 specially (e.g. as an indication of the polling mode by libata), so
the users of platform_get_irq[_byname]() in them would have to filter
out IRQ0 explicitly and this (quite obviously) doesn't scale...
Let's finally get this straight and return -EINVAL instead of IRQ0!
Fixes: a85a6c86c2 ("driver core: platform: Clarify that IRQ 0 is invalid")
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/025679e1-1f0a-ae4b-4369-01164f691511@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When there are 2 matched drivers for a device using
async probe mechanism, the dev->p->async_driver might
be overridden by the last attached driver.
So just skip the later one if the previous matched driver
was not handled by async thread yet.
Below is my use case which having this problem.
Make both driver mmcblk and mmc_test allow async probe,
the dev->p->async_driver will be overridden by the later driver
mmc_test and bind to the device then claim it for testing.
When it happen, mmcblk will never do probe again.
Signed-off-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com>
Link: https://lore.kernel.org/r/20220316074328.1801-1-mark-pk.tsai@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This read the country code from SMBIOS and send the country code
to firmware, firmware will indicate the regulatory domain info of the
country code and then ath11k will use the info.
dmesg:
[ 1242.637173] ath11k_pci 0000:02:00.0: chip_id 0x2 chip_family 0xb board_id 0xff soc_id 0x400c0200
[ 1242.637176] ath11k_pci 0000:02:00.0: fw_version 0x110b09e5 fw_build_timestamp 2021-06-22 09:32 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.HSP.1.1-02533-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
[ 1242.637253] ath11k_pci 0000:02:00.0: worldwide regdomain setting from SMBIOS
[ 1242.637259] ath11k_pci 0000:02:00.0: bdf variant name not found.
[ 1242.637261] ath11k_pci 0000:02:00.0: SMBIOS bdf variant name not set.
[ 1242.637263] ath11k_pci 0000:02:00.0: DT bdf variant name not set.
[ 1242.927543] ath11k_pci 0000:02:00.0: set current country pdev id 0 alpha2 00
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220421023501.32167-1-quic_wgong@quicinc.com
Currently, WBM idle ring HP is updated much before the shadow
configuration is sent to the FW. Any update to the shadow
registers before FW mode on request would not be reflected
on to the actual HW registers failing to bring up the device.
Send FW mode ON QMI request before WBM idle ring HP update
to fix this problem.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00573-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220406094107.17878-12-quic_mpubbise@quicinc.com
WCN6750 is a single PDEV non-DBS chip which supports 2G, 5G and 6G bands.
It is a single LMAC device which can be either hooked to 2G/5G/6G bands.
Add WMI changes to support WCN6750.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00573-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220406094107.17878-11-quic_mpubbise@quicinc.com
Though WCN6750 is a single PDEV device, it is not a
DBS solution. So, do not put HW in DBS mode for WCN6750.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00573-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220406094107.17878-10-quic_mpubbise@quicinc.com
To avoid AUX timeouts and subsequent spurious hotplug interrupts, make
sure that the first DPCD access during detection is a read from an LTTPR
register.
Some ADLP DP link configuration at least with multiple LTTPRs expects
the first DPCD access during the LTTPR/DPCD detection after hotplug to
be a read from the LTTPR range starting with
DP_LT_TUNABLE_PHY_REPEATER_FIELD_DATA_STRUCTURE_REV. The side effect of
this read is to put each LTTPR into the LTTPR transparent or LTTPR
non-transparent mode.
The lack of the above read may leave some of the LTTPRs in non-LTTPR
mode, while other LTTPRs in LTTPR transparent or LTTPR non-transparent
mode (for instance LTTPRs after system suspend/resume that kept their
mode from before suspend). Due to the different AUX timeouts the
different modes imply, the DPCD access from a non-LTTPR range will
timeout and lead to an LTTPR generated hotplug towards the source (which
the LTTPR firmware uses to account for buggy TypeC adapters with a long
wake-up delay).
SYSCROS: 72939
v2: Keep DPCD read-out working on non-LTTPR platforms.
v3: Summarize what and why the patch does at the beginning of the commit
log. (Jani)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220408224629.845887-1-imre.deak@intel.com
