The OV7251 sensor is used as the IR camera sensor on the Microsoft
Surface line of tablets; this provides a 19.2MHz external clock, and
the Windows driver for this sensor configures a 319.2MHz link freq to
the CSI-2 receiver. Add the ability to support those rate to the
driver by defining a new set of PLL configs.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Rather than having the pll settings hidden inside mode blobs, define
them in structs and use a dedicated function to set them. This makes
it simpler to extend the driver to support other frequencies for both
the external clock and desired link frequency.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Each of the defined modes in the ov7251 driver uses the same link
frequency and pixel rate; just drop those members of the modes and
set the controls to read only during initialisation. Add a new
table defining the supported pixel rates to substitue for the values
hardcoded in the modes.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Move the endpoint checking from .probe() to a dedicated function,
and additionally check that the firmware provided link frequencies
are a match for those supported by the driver. Store the index to the
matching link frequency so it can be easily identified later.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Some platforms with an Intel IPU3 have an IR sensor producing 10 bit
greyscale format data that is transmitted over a CSI-2 bus to a CIO2
device - this packs the data into 32 bytes per 25 pixels. Add an entry
to the uAPI header defining that format.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
register_nmi_handler() has no sanity check whether a handler has been
registered already. Such an unintended double-add leads to list corruption
and hard to diagnose problems during the next NMI handling.
Init the list head in the static NMI action struct and check it for being
empty in register_nmi_handler().
[ bp: Fixups. ]
Reported-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/lkml/20220511234332.3654455-1-seanjc@google.com
MWB gain register are used to set gain for each mwb channel mannually.
However, it will involve some artifacts if gain cannot be applied to
each channel synchronously. Enable global gain control to set digital
global gain instead of setting AWB gain separately to fix this issue.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Document that drivers must first initialise a media device before
registering it, and clean up once the media device is unregistered.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add V4L2_ASYNC as a dependency to match other drivers and prevent failures
when compile testing.
Fixes: ff3cc65cad ("media: v4l: async, fwnode: Improve module organisation")
Signed-off-by: Mike Pagano <mpagano@gentoo.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Currently, the defines in this driver are after some structs and
functions, it makes more sense to move them up to the top of the file,
so that the constants can be named together with other defines.
Signed-off-by: Moses Christopher Bollavarapu <mosescb.dev@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Declare static on function 'fimc_isp_video_device_unregister'.
When VIDEO_EXYNOS4_ISP_DMA_CAPTURE=n, compiler warns about
warning: no previous prototype for function [-Wmissing-prototypes]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Kwanghoon Son <k.son@samsung.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
ADV7180 has a built-in mechanism to generate some video patterns,
which is very useful for debug/bring-up activities.
Add support for it.
The test_pattern parameter can be one of the following values:
0: "Single color"
1: "Color bars"
2: "Luma ramp"
3: "Boundary box"
4: "Disable"
Tested on a imx6q board with an ADV7280.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use get_frame_desc() to get the frame desc from the connected source,
and use the provided virtual channel and datatype instead of hardcoded
ones.
get_frame_desc() can contain multiple streams, but as we don't support
multiple streams yet, we will just always use the first stream.
If the source doesn't support get_frame_desc(), fall back to the
previous method of always capturing virtual channel 0 and any datatype.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In ov7670_probe, it always invokes ov7670_power_off() no matter
the execution is successful or failed. So we cannot invoke it
agiain in ov7670_remove().
Fix this by removing ov7670_power_off from ov7670_remove.
Fixes: 030f9f682e ("media: ov7670: control clock along with power")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There is firmware out there that uses "dongwoon,dw9807" compatible string
that never made it to upstream as-is. Add it to the driver to make it load
on such systems.
The chip also has an EEPROM part which is AT24 compatible (for reading
purposes) on a separate I²C address. Adding possible support for this in
the future is not affected by this change.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Depending on the platform we may need to enable and disable three separate
regulators for the imx412.
- DOVDD
Digital I/O power
- AVDD
Analog power
- DVDD
Digital core power
The addition of these regulators shouldn't affect existing users using
fixed-on/firmware-controlled regulators.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Acked-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The imx412/imx577 sensor has a reset line that is active low not active
high. Currently the logic for this is inverted.
The right way to define the reset line is to declare it active low in the
DTS and invert the logic currently contained in the driver.
The DTS should represent the hardware does i.e. reset is active low.
So:
+ reset-gpios = <&tlmm 78 GPIO_ACTIVE_LOW>;
not:
- reset-gpios = <&tlmm 78 GPIO_ACTIVE_HIGH>;
I was a bit reticent about changing this logic since I thought it might
negatively impact @intel.com users. Googling a bit though I believe this
sensor is used on "Keem Bay" which is clearly a DTS based system and is not
upstream yet.
Fixes: 9214e86c0c ("media: i2c: Add imx412 camera sensor driver")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Pull Tegra clk driver updates from Thierry Reding:
This contains a boot time optimization for Tegra chips with BPMP and a
switch from .round_rate() to .determine_rate() to take into account any
maximum rate that might have been set.
Other than that this contains a fix for a DFLL regression on Tegra210
and kerneldoc fixups to avoid build warnings.
* tag 'for-5.19-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
clk: tegra: Update kerneldoc to match prototypes
clk: tegra: Replace .round_rate() with .determine_rate()
clk: tegra: Register clocks from root to leaf
clk: tegra: Add missing reset deassertion
Pull Renesas clk driver updates from Geert Uytterhoeven:
- Add support for the R-Car V4H and RZ/V2M SoCs
- Add the Universal Flash Storage clock on R-Car S4-8
- Add I2C, SSIF-2 (sound), USB, CANFD, OSTM (timer), WDT, SPI Multi
I/O Bus, RSPI, TSU (thermal), and ADC clocks and resets on RZ/G2UL
- Add display clock support on RZ/G2L
- Miscellaneous fixes and improvements
* tag 'renesas-clk-for-v5.19-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers: (36 commits)
clk: renesas: r9a09g011: Add eth clock and reset entries
clk: renesas: Add RZ/V2M support using the rzg2l driver
clk: renesas: rzg2l: Add support for RZ/V2M reset monitor reg
clk: renesas: rzg2l: Make use of CLK_MON registers optional
clk: renesas: rzg2l: Set HIWORD mask for all mux and dividers
clk: renesas: rzg2l: Add read only versions of the clk macros
clk: renesas: rzg2l: Move the DEF_MUX array size calc into the macro
dt-bindings: clock: renesas,rzg2l: Document RZ/V2M SoC
clk: renesas: r9a07g044: Fix OSTM1 module clock name
clk: renesas: r9a07g043: Add clock and reset entries for ADC
clk: renesas: r9a07g043: Add TSU clock and reset entry
clk: renesas: r9a07g043: Add RSPI clock and reset entries
clk: renesas: r9a07g043: Add clock and reset entries for SPI Multi I/O Bus Controller
clk: renesas: r9a07g044: Add DSI clock and reset entries
clk: renesas: r9a07g044: Add LCDC clock and reset entries
clk: renesas: r9a07g044: Add M4 Clock support
clk: renesas: r9a07g044: Add M3 Clock support
clk: renesas: r9a07g044: Add {M2, M2_DIV2} Clocks support
clk: renesas: r9a07g044: Add M1 clock support
clk: renesas: rzg2l: Add DSI divider clk support
...
Instead of having one big enum add one for each register or field.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Commit ca23ecfdbd ("remoteproc/mediatek: support L1TCM") added support
for the l1tcm memory region on the MT8192 SCP, adding a new da_to_va
callback that handles l1tcm while keeping the old one for
back-compatibility with MT8183. However, since the mt8192 compatible was
missing from the dt-binding, the accompanying dt-binding commit
503c64cc42 ("dt-bindings: remoteproc: mediatek: add L1TCM memory region")
mistakenly added this reg as if it were for mt8183. And later
it became common to all platforms as their compatibles were added.
Fix the dt-binding so that the l1tcm reg can be present only on the
supported platforms: mt8192 and mt8195.
Fixes: 503c64cc42 ("dt-bindings: remoteproc: mediatek: add L1TCM memory region")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220511195452.871897-2-nfraprado@collabora.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Using get_cpu() leads to disabling preemption and in this context it is not
possible to acquire the following spinlock_t on PREEMPT_RT because it
becomes a sleeping lock.
Commit 0ea5c27583 ("[SCSI] bnx2fc: common free list for cleanup
commands") says that it is using get_cpu() as a fix in case the CPU is
preempted. While this might be true, the important part is that it is now
using the same CPU for locking and unlocking while previously it always
relied on smp_processor_id(). The date structure itself is protected with
a lock so it does not rely on CPU-local access.
Replace get_cpu() with raw_smp_processor_id() to obtain the current CPU
number which is used as an index for the per-CPU resource.
Link: https://lore.kernel.org/r/20220506105758.283887-5-bigeasy@linutronix.de
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The get_cpu() in fc_exch_em_alloc() was introduced in commit f018b73af6
("[SCSI] libfc, libfcoe, fcoe: use smp_processor_id() only when preempt
disabled") for no other reason than to simply use smp_processor_id()
without getting a warning, because everything is done with the pool->lock
held anyway. However, get_cpu(), by disabling preemption, does not play
well with PREEMPT_RT, particularly when acquiring a regular (and thus
sleepable) spinlock.
Therefore remove the get_cpu() and just use the unstable value as we will
have CPU locality guarantees next by taking the lock. The window of
migration, as noted by Sebastian, is small and even if it happens the
result is correct.
Link: https://lore.kernel.org/r/20211117025956.79616-2-dave@stgolabs.net
Link: https://lore.kernel.org/r/20220506105758.283887-4-bigeasy@linutronix.de
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The per-CPU statistics (struct fc_stats) is updated by getting a stable
per-CPU pointer via get_cpu() + per_cpu_ptr() and then performing the
increment. This can be optimized by using this_cpu_*() which will do
whatever is needed on the architecture to perform the update safe and
efficient. The read out of the individual value (fc_get_host_stats())
should be done by using READ_ONCE() instead of a plain-C access. The
difference is that READ_ONCE() will always perform a single access while
the plain-C access can be split by the compiler into two loads if it
appears beneficial. The usage of u64 has the side-effect that it is also
64bit wide on 32bit architectures and the read is always split into two
loads. The can lead to strange values if the read happens during an update
which alters both 32bit parts of the 64bit value. This can be circumvented
by either using a 32bit variables on 32bit architecures or extending the
statistics with a sequence counter.
Use this_cpu_*() API to update the statistics and READ_ONCE() to read it.
Link: https://lore.kernel.org/r/20220506105758.283887-3-bigeasy@linutronix.de
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
