This reverts commit c12b84d6e0.
The original patch causes a RAS event and subsequent kernel hard-hang
when running the KFDMemoryTest.PtraceAccessInvisibleVram on VG20 and
Arcturus
dmesg output at hang time:
[drm] RAS event of type ERREVENT_ATHUB_INTERRUPT detected!
amdgpu 0000:67:00.0: GPU reset begin!
Evicting PASID 0x8000 queues
Started evicting pasid 0x8000
qcm fence wait loop timeout expired
The cp might be in an unrecoverable state due to an unsuccessful queues preemption
Failed to evict process queues
Failed to suspend process 0x8000
Finished evicting pasid 0x8000
Started restoring pasid 0x8000
Finished restoring pasid 0x8000
[drm] UVD VCPU state may lost due to RAS ERREVENT_ATHUB_INTERRUPT
amdgpu: [powerplay] Failed to send message 0x26, response 0x0
amdgpu: [powerplay] Failed to set soft min gfxclk !
amdgpu: [powerplay] Failed to upload DPM Bootup Levels!
amdgpu: [powerplay] Failed to send message 0x7, response 0x0
amdgpu: [powerplay] [DisableAllSMUFeatures] Failed to disable all smu features!
amdgpu: [powerplay] [DisableDpmTasks] Failed to disable all smu features!
amdgpu: [powerplay] [PowerOffAsic] Failed to disable DPM!
[drm:amdgpu_device_ip_suspend_phase2 [amdgpu]] *ERROR* suspend of IP block <powerplay> failed -5
Signed-off-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Added dedicated function to check if particular fw should be skipped from loading.
Added dedicated function for SMU FW loading via PSP
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: John Clements <john.clements@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On the ASIC powered down(in baco or system suspend),
the dpm_enabled will be set as false. Then all access
(e.g. df state setting issued on RAS error event) to
SMU will be blocked.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As data transfer may starts immediately after i2c eeprom init
completed. Thus i2c eeprom should be initialized after SMU
ready. And i2c data transfer should be prohibited when SMU
down. That is the i2c eeprom fini sequence needs to be
updated also.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The system reboot failed as some IP blocks enter power gate before perform
hw resource destory. Meanwhile use unify interface to set device CGPG to ungate
state can simplify the amdgpu poweroff or reset ungate guard.
Fixes: 487eca11a3 ("drm/amdgpu: fix gfx hang during suspend with video playback (v2)")
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Tested-by: Mengbing Wang <Mengbing.Wang@amd.com>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The variable dp_ref_clk_khz is being initialized with a value that is
never read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Sometimes, WARN_FUNC() and other users of symbol_by_offset() will
associate the first instruction of a symbol with the symbol preceding
it. This is because symbol->offset + symbol->len is already outside of
the symbol's range.
Fixes: 2a362ecc3e ("objtool: Optimize find_symbol_*() and read_symbols()")
Signed-off-by: Julien Thierry <jthierry@redhat.com>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
uclamp_fork() resets the uclamp values to their default when the
reset-on-fork flag is set. It also checks whether the task has a RT
policy, and sets its uclamp.min to 1024 accordingly. However, during
reset-on-fork, the task's policy is lowered to SCHED_NORMAL right after,
hence leading to an erroneous uclamp.min setting for the new task if it
was forked from RT.
Fix this by removing the unnecessary check on rt_task() in
uclamp_fork() as this doesn't make sense if the reset-on-fork flag is
set.
Fixes: 1a00d99997 ("sched/uclamp: Set default clamps for RT tasks")
Reported-by: Chitti Babu Theegala <ctheegal@codeaurora.org>
Signed-off-by: Quentin Perret <qperret@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Patrick Bellasi <patrick.bellasi@matbug.net>
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Link: https://lkml.kernel.org/r/20200416085956.217587-1-qperret@google.com
The static key arch_scale_freq_key only needs to be enabled once (at
boot). This change fixes a bug by which the key was enabled every time cpu0
is started, even as a secondary CPU during cpu hotplug. Secondary CPUs are
started from the idle thread: setting a static key from there means
acquiring a lock and may result in sleeping in the idle task, causing CPU
lockup.
Another consequence of this change is that init_counter_refs() is now
called on each CPU correctly; previously the function on_each_cpu() was
used, but it was called at boot when the only online cpu is cpu0.
[ggherdovich@suse.cz: Tested and wrote changelog]
Fixes: 1567c3e346 ("x86, sched: Add support for frequency invariance")
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lkml.kernel.org/r/20200416054745.740-4-ggherdovich@suse.cz
Some hypervisors such as VMWare ESXi 5.5 advertise support for
X86_FEATURE_APERFMPERF but then fill all MSR's with zeroes. In particular,
MSR_PLATFORM_INFO set to zero tricks the code that wants to know the base
clock frequency of the CPU (highest non-turbo frequency), producing a
division by zero when computing the ratio turbo_freq/base_freq necessary
for frequency invariant accounting.
It is to be noted that even if MSR_PLATFORM_INFO contained the appropriate
data, APERF and MPERF are constantly zero on ESXi 5.5, thus freq-invariance
couldn't be done in principle (not that it would make a lot of sense in a
VM anyway). The real problem is advertising X86_FEATURE_APERFMPERF. This
appears to be fixed in more recent versions: ESXi 6.7 doesn't advertise
that feature.
Fixes: 1567c3e346 ("x86, sched: Add support for frequency invariance")
Signed-off-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lkml.kernel.org/r/20200416054745.740-2-ggherdovich@suse.cz
The variable "nq_ptr" is set but never used, this generates the following
warning while compiling kernel with W=1 option.
drivers/infiniband/hw/bnxt_re/qplib_fp.c: In function 'bnxt_qplib_service_nq':
drivers/infiniband/hw/bnxt_re/qplib_fp.c:303:25: warning:
variable 'nq_ptr' set but not used [-Wunused-but-set-variable]
303 | struct nq_base *nqe, **nq_ptr;
|
Fixes: fddcbbb02a ("RDMA/bnxt_re: Simplify obtaining queue entry from hw ring")
Link: https://lore.kernel.org/r/20200419132046.123887-1-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
fib_tests is spewing errors:
...
Cannot open network namespace "ns1": No such file or directory
Cannot open network namespace "ns1": No such file or directory
Cannot open network namespace "ns1": No such file or directory
Cannot open network namespace "ns1": No such file or directory
ping: connect: Network is unreachable
Cannot open network namespace "ns1": No such file or directory
Cannot open network namespace "ns1": No such file or directory
...
Each test entry in fib_tests is supposed to do its own setup and
cleanup. Right now the $IP commands in fib_suppress_test are
failing because there is no ns1. Add the setup/cleanup and logging
expected for each test.
Fixes: ca7a03c417 ("ipv6: do not free rt if FIB_LOOKUP_NOREF is set on suppress rule")
Signed-off-by: David Ahern <dsahern@gmail.com>
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tracepoint support for QRTR with NS as the first candidate. Later on
this can be extended to core QRTR and transport drivers.
The trace_printk() used in NS has been replaced by tracepoints.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: dsa: b53: Various ARL fixes
This patch series fixes a number of short comings in the existing b53
driver ARL management logic in particular:
- we were not looking up the {MAC,VID} tuples against their VID, despite
having VLANs enabled
- the MDB entries (multicast) would lose their validity as soon as a
single port in the vector would leave the entry
- the ARL was currently under utilized because we would always place new
entries in bin index #1, instead of using all possible bins available,
thus reducing the ARL effective size by 50% or 75% depending on the
switch generation
- it was possible to overwrite the ARL entries because no proper space
verification was done
This patch series addresses all of these issues.
Changes in v2:
- added a new patch to correctly flip invidual VLAN learning vs. shared
VLAN learning depending on the global VLAN state
- added Andrew's R-b tags for patches which did not change
- corrected some verbosity and minor issues in patch #4 to match caller
expectations, also avoid a variable length DECLARE_BITMAP() call
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Flip the IVL_SVL_SELECT bit correctly based on the VLAN enable status,
the default is to perform Shared VLAN learning instead of Individual
learning.
Fixes: 1da6df85c6 ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When asking the ARL to read a MAC address, we will get a number of bins
returned in a single read. Out of those bins, there can essentially be 3
states:
- all bins are full, we have no space left, and we can either replace an
existing address or return that full condition
- the MAC address was found, then we need to return its bin index and
modify that one, and only that one
- the MAC address was not found and we have a least one bin free, we use
that bin index location then
The code would unfortunately fail on all counts.
Fixes: 1da6df85c6 ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ARL {MAC,VID} tuple and the forward entry were off by 0x10 bytes,
which means that when we read/wrote from/to ARL bin index 0, we were
actually accessing the ARLA_RWCTRL register.
Fixes: 1da6df85c6 ("net: dsa: b53: Implement ARL add/del/dump operations")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When support for the MDB entries was added, the valid bit was correctly
changed to be assigned depending on the remaining port bitmask, that is,
if there were no more ports added to the entry's port bitmask, the entry
now becomes invalid. There was another assignment a few lines below that
would override this which would invalidate entries even when there were
still multiple ports left in the MDB entry.
Fixes: 5d65b64a3d ("net: dsa: b53: Add support for MDB")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VLAN is enabled, and an ARL search is issued, we also need to
compare the full {MAC,VID} tuple before returning a successful search
result.
Fixes: 1da6df85c6 ("net: dsa: b53: Implement ARL add/del/dump operations")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv6/ila/ila_xlat.c:604:0: warning: macro "ILA_HASH_TABLE_SIZE" is not used [-Wunused-macros]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the act_ct SW offload in flowtable, The counter of the conntrack
entry will never update. So update the nf_conn_acct conuter in act_ct
flowtable software offload.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I thought I fixed the counting in filename_trans_read_helper() to count
the compat rule count correctly in the final version, but it's still
wrong. To really count the same thing as in the compat path, we'd need
to add up the cardinalities of stype bitmaps of all datums.
Since the kernel currently doesn't implement an ebitmap_cardinality()
function (and computing the proper count would just waste CPU cycles
anyway), just document that we use the field only in case of the old
format and stop updating it in filename_trans_read_helper().
Fixes: 4300590243 ("selinux: implement new format of filename transitions")
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
David Ahern says:
====================
net: Fix looping with vrf, xfrms and qdisc on VRF
Trev reported that use of VRFs with xfrms is looping when a qdisc
is added to the VRF device. The combination of xfrm + qdisc is not
handled by the VRF driver which lost track that it has already
seen the packet.
The XFRM_TRANSFORMED flag is used by the netfilter code for a similar
purpose, so re-use for VRF. Patch 1 drops the #ifdef around setting
the flag in the xfrm output functions. Patch 2 adds a check to
the VRF driver for flag; if set the packet has already passed through
the VRF driver once and does not need to recirculated a second time.
This is a day 1 bug with VRFs; stable wise, I would only take this
back to 4.14. I have a set of test cases which I will submit to
net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid a loop with qdiscs and xfrms, check if the skb has already gone
through the qdisc attached to the VRF device and then to the xfrm layer.
If so, no need for a second redirect.
Fixes: 193125dbd8 ("net: Introduce VRF device driver")
Reported-by: Trev Larock <trev@larock.ca>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPSKB_XFRM_TRANSFORMED and IP6SKB_XFRM_TRANSFORMED are skb flags set by
xfrm code to tell other skb handlers that the packet has been passed
through the xfrm output functions. Simplify the code and just always
set them rather than conditionally based on netfilter enabled thus
making the flag available for other users.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If audit_list_rules_send() fails when trying to create a new thread
to send the rules it also fails to cleanup properly, leaking a
reference to a net structure. This patch fixes the error patch and
renames audit_send_list() to audit_send_list_thread() to better
match its cousin, audit_send_reply_thread().
Reported-by: teroincn@gmail.com
Reviewed-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Heiner Kallweit says:
====================
net: phy: add device-managed devm_mdiobus_register
If there's no special ordering requirement for mdiobus_unregister(),
then driver code can be simplified by using a device-managed version
of mdiobus_register(). Prerequisite is that bus allocation has been
done device-managed too. Else mdiobus_free() may be called whilst
bus is still registered, resulting in a BUG_ON(). Therefore let
devm_mdiobus_register() return -EPERM if bus was allocated
non-managed.
First user of the new functionality is r8169 driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new function devm_mdiobus_register() to simplify the driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there's no special ordering requirement for mdiobus_unregister(),
then driver code can be simplified by using a device-managed version
of mdiobus_register(). Prerequisite is that bus allocation has been
done device-managed too. Else mdiobus_free() may be called whilst
bus is still registered, resulting in a BUG_ON(). Therefore let
devm_mdiobus_register() return -EPERM if bus was allocated
non-managed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY supports monitoring its die temperature as well as two analog
voltages. Add support for it.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Broadcom BCM54140 is a Quad SGMII/QSGMII Copper/Fiber Gigabit
Ethernet transceiver.
This also adds support for tunables to set and get downshift and
energy detect auto power-down.
The PHY has four ports and each port has its own PHY address.
There are per-port registers as well as global registers.
Unfortunately, the global registers can only be accessed by reading
and writing from/to the PHY address of the first port. Further,
there is no way to find out what port you actually are by just
reading the per-port registers. We therefore, have to scan the
bus on the PHY probe to determine the port and thus what address
we need to access the global registers.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
RDB (Register Data Base) registers are used on newer Broadcom PHYs. Add
helper to read, write and modify these registers.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
