The firmware does not respond ARP request and causes ping failure with
following steps:
1. Bring up interface
ifconfig wlan0 up or start wpa_supplicant
2. Set the IP address
ifconfig wlan0 192.168.100.10
3. Bring down interface or
ifconfig wlan0 down or kill wpa_supplicant
4. Bring up interface again and set the same IP address
5. Connect to AP(192.168.100.1) and ping to AP will be failed.
FMAC clears arp_hostip when bringing down the interface, but not set it
back if setting the same IP address. We are able to see the IP address
in interface info(inconfig wlan0) but the ping still cannot work because
the firmware ARP offload does not respond the ARP request.
Because of that, we remove "arp_hostip_clear" from function
"brcmf_netdev_stop"
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587970803-77700-3-git-send-email-chi-hsien.lin@cypress.com
Add a HID_QUIRK_NO_INIT_REPORTS quirk for the Dell K12A keyboard-dock,
which can be used with various Dell Venue 11 models.
Without this quirk the keyboard/touchpad combo works fine when connected
at boot, but when hotplugged 9 out of 10 times it will not work properly.
Adding the quirk fixes this.
Cc: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When the kernel is built with lockdep support and the owl-dma driver is
used, the following message is shown:
[ 2.496939] INFO: trying to register non-static key.
[ 2.501889] the code is fine but needs lockdep annotation.
[ 2.507357] turning off the locking correctness validator.
[ 2.512834] CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.6.3+ #15
[ 2.519084] Hardware name: Generic DT based system
[ 2.523878] Workqueue: events_freezable mmc_rescan
[ 2.528681] [<801127f0>] (unwind_backtrace) from [<8010da58>] (show_stack+0x10/0x14)
[ 2.536420] [<8010da58>] (show_stack) from [<8080fbe8>] (dump_stack+0xb4/0xe0)
[ 2.543645] [<8080fbe8>] (dump_stack) from [<8017efa4>] (register_lock_class+0x6f0/0x718)
[ 2.551816] [<8017efa4>] (register_lock_class) from [<8017b7d0>] (__lock_acquire+0x78/0x25f0)
[ 2.560330] [<8017b7d0>] (__lock_acquire) from [<8017e5e4>] (lock_acquire+0xd8/0x1f4)
[ 2.568159] [<8017e5e4>] (lock_acquire) from [<80831fb0>] (_raw_spin_lock_irqsave+0x3c/0x50)
[ 2.576589] [<80831fb0>] (_raw_spin_lock_irqsave) from [<8051b5fc>] (owl_dma_issue_pending+0xbc/0x120)
[ 2.585884] [<8051b5fc>] (owl_dma_issue_pending) from [<80668cbc>] (owl_mmc_request+0x1b0/0x390)
[ 2.594655] [<80668cbc>] (owl_mmc_request) from [<80650ce0>] (mmc_start_request+0x94/0xbc)
[ 2.602906] [<80650ce0>] (mmc_start_request) from [<80650ec0>] (mmc_wait_for_req+0x64/0xd0)
[ 2.611245] [<80650ec0>] (mmc_wait_for_req) from [<8065aa10>] (mmc_app_send_scr+0x10c/0x144)
[ 2.619669] [<8065aa10>] (mmc_app_send_scr) from [<80659b3c>] (mmc_sd_setup_card+0x4c/0x318)
[ 2.628092] [<80659b3c>] (mmc_sd_setup_card) from [<80659f0c>] (mmc_sd_init_card+0x104/0x430)
[ 2.636601] [<80659f0c>] (mmc_sd_init_card) from [<8065a3e0>] (mmc_attach_sd+0xcc/0x16c)
[ 2.644678] [<8065a3e0>] (mmc_attach_sd) from [<8065301c>] (mmc_rescan+0x3ac/0x40c)
[ 2.652332] [<8065301c>] (mmc_rescan) from [<80143244>] (process_one_work+0x2d8/0x780)
[ 2.660239] [<80143244>] (process_one_work) from [<80143730>] (worker_thread+0x44/0x598)
[ 2.668323] [<80143730>] (worker_thread) from [<8014b5f8>] (kthread+0x148/0x150)
[ 2.675708] [<8014b5f8>] (kthread) from [<801010b4>] (ret_from_fork+0x14/0x20)
[ 2.682912] Exception stack(0xee8fdfb0 to 0xee8fdff8)
[ 2.687954] dfa0: 00000000 00000000 00000000 00000000
[ 2.696118] dfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 2.704277] dfe0: 00000000 00000000 00000000 00000000 00000013 00000000
The obvious fix would be to use 'spin_lock_init()' on 'pchan->lock'
before attempting to call 'spin_lock_irqsave()' in 'owl_dma_get_pchan()'.
However, according to Manivannan Sadhasivam, 'pchan->lock' was supposed
to only protect 'pchan->vchan' while 'od->lock' does a similar job in
'owl_dma_terminate_pchan()'.
Therefore, this patch substitutes 'pchan->lock' with 'od->lock' and
removes the 'lock' attribute in 'owl_dma_pchan' struct.
Fixes: 47e20577c2 ("dmaengine: Add Actions Semi Owl family S900 DMA driver")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Andreas Färber <afaerber@suse.de>
Link: https://lore.kernel.org/r/c6e6cdaca252b5364bd294093673951036488cf0.1588439073.git.cristian.ciocaltea@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Modify dw_edma_device_transfer() to also support the semantics of dma
device transfer for additional use cases involving pcitest utility as a
local initiator.
For its original use case, dw-edma supported the semantics of dma device
transfer from the perspective of a remote initiator who is located across
the PCIe bus from dma channel hardware.
To a remote initiator, DMA_DEV_TO_MEM means using a remote dma WRITE
channel to transfer from remote memory to local memory. A WRITE channel
would be employed on the remote device in order to move the contents of
remote memory to the bus destined for local memory.
To a remote initiator, DMA_MEM_TO_DEV means using a remote dma READ
channel to transfer from local memory to remote memory. A READ channel
would be employed on the remote device in order to move the contents of
local memory to the bus destined for remote memory.
>From the perspective of a local dma initiator who is co-located on the
same side of the PCIe bus as the dma channel hardware, the semantics of
dma device transfer are flipped.
To a local initiator, DMA_DEV_TO_MEM means using a local dma READ channel
to transfer from remote memory to local memory. A READ channel would be
employed on the local device in order to move the contents of remote
memory to the bus destined for local memory.
To a local initiator, DMA_MEM_TO_DEV means using a local dma WRITE channel
to transfer from local memory to remote memory. A WRITE channel would be
employed on the local device in order to move the contents of local memory
to the bus destined for remote memory.
To support local dma initiators, dw_edma_device_transfer() is modified to
now examine the direction field of struct dma_slave_config for the channel
which initiators can configure by calling dmaengine_slave_config().
If direction is configured as either DMA_DEV_TO_MEM or DMA_MEM_TO_DEV,
local initiator semantics are used. If direction is a value other than
DMA_DEV_TO_MEM nor DMA_MEM_TO_DEV, then remote initiator semantics are
used. This should maintain backward compatibility with the original use
case of dw-edma.
The dw-edma-test utility is an example of a remote initiator. From reading
its patch, dw-edma-test does not specifically set the direction field of
struct dma_slave_config. Since dw_edma_device_transfer() also does not
check the direction field of struct dma_slave_config, it seems safe to use
this convention in dw-edma to support both local and remote initiator
semantics.
Signed-off-by: Alan Mikhak <alan.mikhak@sifive.com>
Link: https://lore.kernel.org/r/1588122633-1552-1-git-send-email-alan.mikhak@sifive.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In Multi-AP VAP scenario with frequent interface up-down, there is a
chance that ath11k_mgmt_over_wmi_tx_work() will dequeue a skb
corresponding to currently deleted/stopped vdev.
FW will assert on receiving mgmt_tx_wmi cmd for already deleted vdev.
Hence adding validation checks for arvif present on the corresponding
ar before sending mgmt_tx_wmi cmd.
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588049126-1490-2-git-send-email-murugana@codeaurora.org
First set of iwlwifi patches intended for v5.8
* TX queue debugfs improvements;
* Support for a few new FW API versions;
* Remove deprecated scan FW API version;
* New hw configs and other related changes;
* Support for NPK buffers in debugging;
* More debugging fetures;
* Some other small fixes and clean-ups;
# gpg: Signature made Fri 24 Apr 2020 04:39:43 PM EEST using RSA key ID 1A3CC5FA
# gpg: Good signature from "Luciano Roth Coelho (Luca) <luca@coelho.fi>"
# gpg: aka "Luciano Roth Coelho (Intel) <luciano.coelho@intel.com>"
A 32-bit version of mcelog issuing ioctls on /dev/mcelog causes errors
like the following:
MCE_GET_RECORD_LEN: Inappropriate ioctl for device
This is due to a missing compat_ioctl callback.
Assign to it compat_ptr_ioctl() as a generic implementation of the
.compat_ioctl file operation to ioctl functions that either ignore the
argument or pass a pointer to a compatible data type.
[ bp: Massage commit message. ]
Signed-off-by: He Zhe <zhe.he@windriver.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/1583303947-49858-1-git-send-email-zhe.he@windriver.com
When building arm64 allmodconfig:
ERROR: modpost: "zynqmp_pm_fpga_load" [drivers/fpga/zynqmp-fpga.ko] undefined!
ERROR: modpost: "zynqmp_pm_fpga_get_status" [drivers/fpga/zynqmp-fpga.ko] undefined!
These functions were added to drivers/fpga/zynqmp-fpga.c but not
exported so the module build breaks. Export them so that they can be
used in modules properly.
Fixes: 4db8180ffe ("firmware: xilinx: Remove eemi ops for fpga related APIs")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20200502025958.2714249-1-natechancellor@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The validation kernel doc script complains about undescribed
function parameters
.../dmaengine.c:155: warning: Function parameter or member 'dev' not descr ibed in 'dev_to_dma_chan'
.../dmaengine.c:251: warning: cannot understand function prototype: 'dma_cap_mask_t dma_cap_mask_all; '
.../dmaengine.c:257: warning: cannot understand function prototype: 'struct dma_chan_tbl_ent '
.../dmaengine.c:264: warning: cannot understand function prototype: 'struct dma_chan_tbl_ent __percpu *channel_table[DMA_TX_TYPE_END]; '
.../dmaengine.c:304: warning: Function parameter or member 'chan' not described in 'dma_chan_is_local'
.../dmaengine.c:304: warning: Function parameter or member 'cpu' not described in 'dma_chan_is_local'
.../dmaengine.c:414: warning: Function parameter or member 'chan' not described in 'balance_ref_count'
.../dmaengine.c:447: warning: Function parameter or member 'chan' not described in 'dma_chan_get'
.../dmaengine.c:494: warning: Function parameter or member 'chan' not described in 'dma_chan_put'
Add descriptions to the function parameters and in some cases update
existing text as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200429122151.50989-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Binding in Documentation is still "operating-points-v2-kryo-cpu".
Restore the old binding to fix the compatibility problem.
Fixes: a8811ec764 ("cpufreq: qcom: Add support for krait based socs")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Add the device tree for Akebi96. Akebi96 is a 96boards certified
development board based on UniPhir LD20.
( https://www.96boards.org/product/akebi96/ )
This board has;
- MAX3421 USB-SPI chip on SPI port3 (for USB gadget port)
- Simple frame buffer with 1080p fixed resolution.
- I2S port which is connected to aout1b instead of aout1.
- 3 serial ports, only serial3 has CTS/RTS.
- No NAND, only eMMC on the board.
- OP-TEE installed firmware.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Documentation/devicetree/bindings/spi/spi-uniphier.txt requires
#address-cells and #size-cells, but they are missing in actual DT files.
Also, 'make ARCH=arm64 dtbs_check' is really noisy.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Documentation/devicetree/bindings/spi/spi-uniphier.txt requires
#address-cells and #size-cells, but they are missing in actual DT files.
Also, 'make ARCH=arm dtbs_check' is really noisy.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The RGMII PHY implemented in PXs3 ref board needs to change
drive-strength properties of the Ethernet Tx pins to stabilize the PHY.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add 'aliases' properties for ethernet device.
U-Boot performs a fix-up of the MAC address and will overwrite the values
from the Linux devicetree for aliased ethernet device. The MAC address can
be inherited from U-Boot by adding aliases of ethernet devices.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add an 'aliases' property for ethernet device.
U-Boot performs a fix-up of the MAC address and will overwrite the values
from the Linux devicetree for aliased ethernet device. The MAC address can
be inherited from U-Boot by adding aliases of ethernet devices.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Hugh reported that his trusty G5 crashed after a few hours under load
with an "Unrecoverable exception 380".
The crash is in interrupt_return() where we check lazy_irq_pending(),
which calls get_paca() and with CONFIG_DEBUG_PREEMPT=y that goes to
check_preemption_disabled() via debug_smp_processor_id().
As Nick explained on the list:
Problem is MSR[RI] is cleared here, ready to do the last few things
for interrupt return where we're not allowed to take any other
interrupts.
SLB interrupts can happen just about anywhere aside from kernel
text, global variables, and stack. When that hits, it appears to be
unrecoverable due to RI=0.
The problematic access is in preempt_count() which is:
return READ_ONCE(current_thread_info()->preempt_count);
Because of THREAD_INFO_IN_TASK, current_thread_info() just points to
current, so the access is to somewhere in kernel memory, but not on
the stack or in .data, which means it can cause an SLB miss. If we
take an SLB miss with RI=0 it is fatal.
The easiest solution is to add a version of lazy_irq_pending() that
doesn't do the preemption check and call it from the interrupt return
path.
Fixes: 68b34588e2 ("powerpc/64/sycall: Implement syscall entry/exit logic in C")
Reported-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200502143316.929341-1-mpe@ellerman.id.au
Karsten Graul says:
====================
net/smc: add and delete link processing
These patches add the 'add link' and 'delete link' processing as
SMC server and client. This processing allows to establish and
remove links of a link group dynamically.
v2: Fix mess up with unused static functions. Merge patch 8 into patch 4.
Postpone patch 13 to next series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As SMC server, when a second link was deleted, trigger the setup of an
asymmetric link. Do this by enqueueing a local ADD_LINK message which
is processed by the LLC layer as if it were received from peer. Do the
same when a new IB port became active and a new link could be created.
smc_llc_srv_add_link_local() enqueues a local ADD_LINK message.
And smc_llc_srv_delete_link_local() is used the same way to enqueue a
local DELETE_LINK message. This is used when an IB port is no longer
active.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add smc_llc_process_srv_delete_link() to process a DELETE_LINK request
as SMC server. When the request is to delete ALL links then terminate
the whole link group. If not, find the link to delete by its link_id,
send the DELETE_LINK request LLC message and wait for the response.
No matter if a response was received, clear the deleted link and update
the link group state.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add smc_llc_process_cli_delete_link() to process a DELETE_LINK request
as SMC client. When the request is to delete ALL links then terminate
the whole link group. If not, find the link to delete by its link_id,
send the DELETE_LINK response LLC message and then clear the deleted
link. Finally determine and update the link group state.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a work that is scheduled when a new DELETE_LINK LLC request is
received. The work will call either the SMC client or SMC server
DELETE_LINK processing.
And use the LLC flow framework to process incoming DELETE_LINK LLC
messages, scheduling the llc_del_link_work for those events.
With these changes smc_lgr_forget() is only called by one function and
can be migrated into smc_lgr_cleanup_early().
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a link group moved from asymmetric to symmetric state then the
dangling asymmetric link can be deleted. Add smc_llc_find_asym_link() to
find the respective link and add smc_llc_delete_asym_link() to delete
it.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch finalizes the ADD_LINK processing of new links. Send the
CONFIRM_LINK request to the peer, receive the response and set link
state to ACTIVE.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Part of SMC server new link establishment is the exchange of rkeys for
used buffers.
Loop over all used RMB buffers and send ADD_LINK_CONTINUE LLC messages
to the peer.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First set of functions to process an ADD_LINK LLC request as an SMC
server. Find an alternate IB device, determine the new link group type
and get the index for the new link. Then initialize the link and send
the ADD_LINK LLC message to the peer. Save the contents of the response,
ready the link, map all used buffers and register the buffers with the
IB device. If any error occurs, stop the processing and clear the link.
And call smc_llc_srv_add_link() in af_smc.c to start second link
establishment after the initial link of a link group was created.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch finalizes the ADD_LINK processing of new links. Receive the
CONFIRM_LINK request from peer, complete the link initialization,
register all used buffers with the IB device and finally send the
CONFIRM_LINK response, which completes the ADD_LINK processing.
And activate smc_llc_cli_add_link() in af_smc.c.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Part of the SMC client new link establishment process is the exchange of
rkeys for all used buffers.
Add new LLC message type ADD_LINK_CONTINUE which is used to exchange
rkeys of all current RMB buffers. Add functions to iterate over all
used RMB buffers of the link group, and implement the ADD_LINK_CONTINUE
processing.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First set of functions to process an ADD_LINK LLC request as an SMC
client. Find an alternate IB device, determine the new link group type
and get the index for the new link. Then ready the link, map the buffers
and send an ADD_LINK LLC response. If any error occurs, send a reject
LLC message and terminate the processing.
Add smc_llc_alloc_alt_link() to find a free link index for a new link,
depending on the new link group type.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sameeh Jubran says:
====================
Enhance current features in ena driver
Difference from v2:
* dropped patch "net: ena: move llq configuration from ena_probe to ena_device_init()"
* reworked patch ""net: ena: implement ena_com_get_admin_polling_mode() to drop the prototype
Difference from v1:
* reodered paches #01 and #02.
* dropped adding Rx/Tx drops to ethtool in patch #08
V1:
This patchset introduces the following:
* minor changes to RSS feature
* add total rx and tx drop counter
* add unmask_interrupt counter for ethtool statistics
* add missing implementation for ena_com_get_admin_polling_mode()
* some minor code clean-up and cosmetics
* use SHUTDOWN as reset reason when closing interface
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract code to ena_indirection_table_set() to make
the code cleaner.
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
