On the Amlogic GXL/GXM SoCs, only the USB control registers are available,
the PHY mode being handled in the PHY registers.
Thus, handle the PHY mode registers in separate regmaps and prepare
support for Amlogic GXL/GXM SoCs by moving the regmap setup in a callback
set in the SoC match data.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The Amlogic GXL and GXM is slightly different from the Amlogic G12A Glue.
The GXL SoCs only embeds 2 USB2 PHYs and no USB3 PHYs, and the GXM SoCs
embeds 3 USB2 PHYs.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Convert USB DWC3 bindings to DT schema format using json-schema.
Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The flow from function dwc3_gadget_ep_dequeue() is not easy to follow.
Refactor it for easier read. No functional change in this commit.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Remove 2 unnecessary checks:
1) A request in the started_list must have its trb field set. So
checking for req->trb is unnecessary.
2) An endpoint must have started (and have not ended) for the request to
still be in the started_list. There's no point to check if the endpoint
is started. We had this check because previously the driver didn't
handle the endpoint's started/ended flags for END_TRANSFER command
properly. See commit 9f45581f5e ("usb: dwc3: gadget: early giveback
if End Transfer already completed").
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If a request is dequeued, the transfer is cancelled. Give back all
the started requests.
In most scenarios, the function driver dequeues all requests of a
transfer when there's a failure. If the function driver follows this,
then it's fine. If not, then we'd be skipping TRBs at different points
within the dequeue and enqueue pointers, making dequeue/enqueue pointers
useless. To enforce and make sure that we're properly skipping TRBs,
cancel all the started requests and give back all the cancelled requests
to the function drivers.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
DWC3 must not issue CLEAR_STALL command to control endpoints. The
controller automatically clears the STALL when it receives the SETUP
token. Also, when the driver receives ClearFeature(halt_ep), DWC3 must
stop any active transfer from the endpoint and give back all the
requests to the function drivers.
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Update device tree binding document for aspeed vhub's device IDs and
string properties.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch moves patch-usb1-dev-desc logic from get-descriptor handler
to "ast_vhub_fixup_usb1_dev_desc" function so the code is executed only
once (at vhub initial time).
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The patch overrides idVendor, idProduct and bcdDevice fields in vhub
Device Descriptor if according device tree properties are defined.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If "vhub,string-descriptor" device tree property is defined, the driver
will load string descriptors from device tree; otherwise, the default
string descriptors will be used.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The USB LANGID validation code in "check_user_usb_string" function is
moved to "usb_validate_langid" function which can be used by other usb
gadget drivers.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch introduces a link list to store string descriptors with
different languages, and "ast_vhub_rep_string" function is also improved
to support multiple language usb strings.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch evaluates vhub ports' irq mask before going through per-port
irq handling one by one, which helps to speed up irq handling in case
there is no port interrupt.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The DRD module calls dwc3_set_mode() on role switches, i.e. when a device is
being plugged in. In order to support continuous runtime power management when
plugging in / unplugging a cable, we need to call pm_runtime_get_sync() in
this path.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Mark all local functions static to fix sparse warnings.
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch corrects the SPDX License Identifier style in
header files related to DesignWare USB2 DRD Core Support.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch corrects the SPDX License Identifier style in
header files related to DesignWare USB3 DRD Core Support.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch corrects the SPDX License Identifier style in
header files related to USB peripheral controller drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Older compilers like gcc-4.8 don't see that the variable is
initialized when it is used:
In file included from include/linux/compiler_types.h:68:0,
from <command-line>:0:
drivers/hid/intel-ish-hid/ishtp-fw-loader.c: In function 'load_fw_from_host':
include/linux/compiler-gcc.h:75:45: warning: 'fw_info.ldr_capability.max_dma_buf_size' may be used uninitialized in this function [-Wmaybe-uninitialized]
#define __UNIQUE_ID(prefix) __PASTE(__PASTE(__UNIQUE_ID_, prefix), __COUNTER__)
^
drivers/hid/intel-ish-hid/ishtp-fw-loader.c:770:22: note: 'fw_info.ldr_capability.max_dma_buf_size' was declared here
struct shim_fw_info fw_info;
^
Make sure to initialize it before returning an error from ish_query_loader_prop().
Fixes: 91b228107d ("HID: intel-ish-hid: ISH firmware loader client driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This is a driver for video encoder with VGA and DVI/HDMI outputs.
There is no documentation for the chip -- the operation was guessed from
what was sniffed on a Dell Wyse 3020 ThinOS terminal, the register names
come from the ch7035 driver in Mediatek's GPL code dump.
Only bare minimum is implemented -- no fancy stuff, such as scaling. That
would only worsen our misery. We don't load the firmware and we don't need
to even bother enabling the MCU. There are probably no distributable
firmware images anyway.
Tested with a handful of monitors ranging from 1024x768@75 to 1400x1050@60,
with VGA as well as DVI.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200424213539.93157-4-lkundrak@v3.sk
htt stats are not working after htt peer stats display
and also after htt peer stats reset. Trying to dump htt
stats shows "Resource temporarily unavailable".
This is because of "ar->debug.htt_stats.stats_req" member is being
consecutively used for all htt stats without being reset
during the previous usage. Hence assigning NULL to this member
after freeing the allocated memory fixes the issue.
console logs below:
# echo 9 >/sys/kernel/debug/ath11k/ipq8074/mac1/htt_stats_type
# cat /sys/kernel/debug/ath11k/ipq8074/mac1/htt_stats_type
9
# cat /sys/kernel/debug/ath11k/ipq8074/mac1/htt_stats
cat: can't open '/sys/kernel/debug/ath11k/ipq8074/mac1/htt_stats'
: Resource temporarily unavailable
Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588592755-10427-1-git-send-email-ssreeela@codeaurora.org
The struct cfg80211_wowlan of NET_DETECT WoWLAN feature share the same
struct cfg80211_sched_scan_request together with scheduled scan request
feature, and max_sched_scan_reqs of wiphy is only used for sched scan,
and ath10k does not support scheduled scan request feature, so ath10k
does not set flag NL80211_FEATURE_SCHED_SCAN_RANDOM_MAC_ADDR, but ath10k
set max_sched_scan_reqs of wiphy to a non zero value 1, then function
nl80211_add_commands_unsplit of cfg80211 will set it support command
NL80211_CMD_START_SCHED_SCAN because max_sched_scan_reqs is a non zero
value, but actually ath10k not support it, then it leads a mismatch result
for sched scan of cfg80211, then application shill found the mismatch and
stop running case of MAC random address scan and then the case fail.
After remove max_sched_scan_reqs value, it keeps match for sched scan and
case of MAC random address scan pass.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Tested with QCA6174 PCIe with firmware WLAN.RM.4.4.1-00110-QCARMSWP-1.
Fixes: ce834e280f ("ath10k: support NET_DETECT WoWLAN feature")
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20191114050001.4658-1-wgong@codeaurora.org
As the exisiting CE configurations are defined in global, there
are the chances of QCA99X0 family chipsets CE configurations
are getting changed by the ath10k_pci_override_ce_config()
function.
The override will be hit and CE5 configurations will be changed,
when the user bring up the QCA99X0 chipsets along with QCA6174
or QCA9377 chipset. (Bring up QCA99X0 family chipsets after
QCA6174 or QCA9377).
Hence, fixing this issue by moving the global CE configuration
to radio specific CE configuration.
Tested hardware: QCA9888 & QCA6174
Tested firmware: 10.4-3.10-00047 & WLAN.RM.4.4.1.c3-00058
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587649759-14381-1-git-send-email-mkenna@codeaurora.org
When building the x86 EFI stub with Clang, the libstub Makefile rules
that manipulate the ELF object files may throw an error like:
STUBCPY drivers/firmware/efi/libstub/efi-stub-helper.stub.o
strip: drivers/firmware/efi/libstub/efi-stub-helper.stub.o: Failed to find link section for section 10
objcopy: drivers/firmware/efi/libstub/efi-stub-helper.stub.o: Failed to find link section for section 10
This is the result of a LLVM feature [0] where symbol references are
stored in a LLVM specific .llvm_addrsig section in a non-transparent way,
causing generic ELF tools such as strip or objcopy to choke on them.
So force the compiler not to emit these sections, by passing the
appropriate command line option.
[0] https://sourceware.org/bugzilla/show_bug.cgi?id=23817
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Peter Collingbourne <pcc@google.com>
Cc: Sami Tolvanen <samitolvanen@google.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Suggested-by: Fangrui Song <maskray@google.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Commit
22090f84bc ("efi/libstub: unify EFI call wrappers for non-x86")
refactored the macros that are used to provide wrappers for mixed-mode
calls on x86, allowing us to boot a 64-bit kernel on 32-bit firmware.
Unfortunately, this broke mixed mode boot due to the fact that
efi_is_native() is not a macro on x86.
All of these macros should go together, so rather than testing each one
to see if it is defined, condition the generic macro definitions on a
new ARCH_HAS_EFISTUB_WRAPPERS, and remove the wrapper definitions on x86
as well if CONFIG_EFI_MIXED is not enabled.
Fixes: 22090f84bc ("efi/libstub: unify EFI call wrappers for non-x86")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Link: https://lore.kernel.org/r/20200504150248.62482-1-nivedita@alum.mit.edu
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Fixes the following warnings for both g5 and g6 SoCs:
arch/arm/boot/dts/aspeed-g5.dtsi:376.19-381.8: Warning
(unit_address_vs_reg): /ahb/apb/lpc@1e789000/lpc-bmc@0/kcs1@0: node
has a unit name, but no reg property
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The AST2600 XDMA engine requires the PCI-E root control reset be cleared
as well, so add a phandle to that syscon reset.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add a node for the XDMA engine with all the necessary information.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add a node for the XDMA engine with all the necessary information.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The Yosemite V2 is a facebook multi-node server
platform that host four OCP server. The BMC
in the Yosemite V2 platform based on AST2500 SoC.
This patch adds linux device tree entry related to
Yosemite V2 specific devices connected to BMC SoC.
Signed-off-by: Manikandan Elumalai <manikandan.hcl.ers.epl@gmail.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Vijay Khemka <vkhemka@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Nicole is an OpenPower machine with an Aspeed 2500 BMC SoC manufactured
by YADRO.
Signed-off-by: Alexander Filippov <a.filippov@yadro.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Patrick Williams <patrick@stwcx.xyz>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Set the bus id for each mux channel to avoid switching channels
multiple times
Signed-off-by: Ben Pai <Ben_Pai@wistron.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Connect the BMP280 and DPS310 to the hwmon subsystem with iio-hwmon
nodes.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
