Currently HSD20_IPS is defined as "true" and will always result in a
non-zero result even if it is defined as "false" because it is an array
and that will never be zero. Fix this by defining it as an integer 1
rather than a literal string.
Addessses-Coverity: ("Array compared against 0")
Fixes: f03c9b7884 ("staging: fbtft: fb_st7789v: Initialize the Display")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200521135038.345878-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If uboot passes a blank string to console_setup then it results in
a trashed memory. Ultimately, the kernel crashes during freeing up
the memory.
This fix checks if there is a blank parameter being
passed to console_setup from uboot. In case it detects that
the console parameter is blank then it doesn't setup the serial
device and it gracefully exits.
Link: https://lore.kernel.org/r/20200522065306.83-1-shreyas.joshi@biamp.com
Signed-off-by: Shreyas Joshi <shreyas.joshi@biamp.com>
Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
[pmladek@suse.com: Better format the commit message and code, remove unnecessary brackets.]
Signed-off-by: Petr Mladek <pmladek@suse.com>
Instead of using the driver-specific rtsx_pci_update_cfg_byte() to update
the PCIe Link Control Register, use pcie_capability_clear_and_set_word()
like the rest of the kernel does. This makes it easier to maintain ASPM
across the PCI core and drivers.
Remove the now-unused rtsx_pci_update_cfg_byte() and ASPM_MASK_NEG
definitions.
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20200521180545.1159896-5-helgaas@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kishon writes:
phy: for 5.8
*) Add new PHY driver to support Cadence SALVO PHY which supports USB3 & USB2
*) Add new PHY driver to support Intel ComboPhy which supports PCIe, SATA and
EMAC
*) Add new PHY driver for Qualcomm IPQ40xx USB PHY
*) Add new PHY driver for Synopsys FemtoPHY V2 driver used in Qualcomm SOCs
*) Add support for Qualcomm SM8250 UFS PHY and SM8150 QMP USB3 PHY in
qcom-qmp-phy driver
*) Add support for Amlogic USB2 PHY on Meson8m2 in phy-meson8b-usb2 driver
*) Add DisplayPort mode support in Wiz (TI Cadence PHY wrapper), to enable eDP
in TI's J721E SoC
*) Add support for super speed USB PHY in TI's AM654 SoC
*) Add fix in Broadcom Stingray USB PHY to get USB PHY PLL lock reliably
*) Add fix in Samsung phy-s5pv210-usb2 to get USB working on s5pv210
*) Add fix in Amlogic phy-meson8b-usb2 to get host only mode working on Meson8
*) Add fix in Cadence phy-cadence-sierra to get USB3 device disconnect issue
*) Convert meson8b-usb2-phy, qcom-qmp-phy, rcar-gen3-phy-usb2 and
rcar-gen3-phy-usb3 device tree binding to YAML schema
*) Minor fixes and cleanups in phy-cpcap-usb, j721e-wiz, omap-usb2,
phy-bcm-sr-usb, phy-brcm-usb PHY driver
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (43 commits)
phy: intel: Add driver support for ComboPhy
dt-bindings: phy: Add YAML schemas for Intel ComboPhy
dt-bindings: phy: Add PHY_TYPE_XPCS definition
phy: qcom-qmp: Add QMP V3 USB3 PHY support for SC7180
dt-bindings: phy: qcom,qmp-usb3-dp: Add support for SC7180
dt-bindings: phy: qcom,qmp-usb3-dp: Add dt bindings for USB3 DP PHY
dt-bindings: phy: qcom,qmp: Convert QMP PHY bindings to yaml
phy: cadence: sierra: Fix for USB3 U1/U2 state
phy: ti: am654: add support for USB super-speed
phy: ti: am654: show up in regmap debugfs
drivers: phy: sr-usb: do not use internal fsm for USB2 phy init
dt-bindings: phy: renesas: usb3-phy: add r8a77961 support
dt-bindings: phy: renesas: usb3-phy: convert bindings to json-schema
dt-bindings: phy: renesas: usb2-phy: add r8a77961 support
dt-bindings: phy: renesas: usb2-phy: convert bindings to json-schema
phy: qcom-qmp: Ensure register indirection arrays initialized
phy: omap-usb2: Clean up exported header
phy: phy-bcm-ns2-usbdrd: Constify phy_ops
phy: phy-brcm-usb: Constify static structs
phy: sr-usb: Constify phy_ops
...
Vinod writes:
soundwire updates for v5.8-rc1
This contains sdw_master_device patches and other updates done by Intel
folks.
Details:
- sdw_master_device to represent the master instances.
- sysfs properties for sdw_master_device and sdw_slave.
- Documentation update for TDM modes.
- some code cleanup patches and odd updates.
* tag 'soundwire-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire:
soundwire: intel: use a single module
soundwire: fix spelling mistake
soundwire: fix trailing line in sysfs_slave.c
soundwire: add Slave sysfs support
soundwire: master: add sysfs support
soundwire: disco: s/ch/channels/
soundwire: master: add runtime pm support
soundwire: bus_type: add sdw_master_device support
soundwire: bus: add unique bus id
soundwire: bus_type: introduce sdw_slave_type and sdw_master_type
soundwire: bus: rename sdw_bus_master_add/delete, add arguments
soundwire: intel: (cosmetic) remove multiple superfluous "else" statements
soundwire: (cosmetic) remove multiple superfluous "else" statements
soundwire: qcom: Use IRQF_ONESHOT
soundwire: bus: reduce verbosity on enumeration
soundwire: debugfs: clarify SDPX license with GPL-2.0-only
soundwire: slave: don't init debugfs on device registration error
Documentation: SoundWire: clarify TDM mode support
soundwire: qcom: fix error handling in probe
soundwire: intel: use asoc_rtd_to_cpu() / asoc_rtd_to_codec() macro for DAI pointer
Due to being embedded into the CPU cores MIPS count/compare timer
frequency is changed together with the CPU clocks alteration.
In case if frequency really changes the kernel clockevent framework
must be notified, otherwise the kernel timers won't work correctly.
Fix this by calling clockevents_update_freq() for each r4k clockevent
handlers registered per available CPUs.
Traditionally MIPS r4k-clock are clocked with CPU frequency divided by 2.
But this isn't true for some of the platforms. Due to this we have to save
the basic CPU frequency, so then use it to scale the initial timer
frequency (mips_hpt_frequency) and pass the updated value further to the
clockevent framework.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Georgi writes:
interconnect changes for 5.8
These are the interconnect changes for the 5.8-rc1 merge window:
Core changes:
- Convert the framework core from tristate to bool to make handling
dependencies between other core frameworks easier
- Add of_icc_get_by_index()
- Add devm_of_icc_get() helper function
- Add icc_enable() and icc_disable() helpers
New drivers:
- Platform driver for NXP i.MX8MM SoC
- Platform driver for NXP i.MX8MN SoC
- Platform driver for NXP i.MX8MQ SoC
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
* tag 'icc-5.8-rc1' of https://git.linaro.org/people/georgi.djakov/linux:
interconnect: Remove unused module exit code from core
interconnect: Disallow interconnect core to be built as a module
interconnect: Add of_icc_get_by_index() helper function
interconnect: Add helpers for enabling/disabling a path
interconnect: imx: Fix return value check in imx_icc_node_init_qos()
interconnect: imx: Add platform driver for imx8mn
interconnect: imx: Add platform driver for imx8mq
interconnect: imx: Add platform driver for imx8mm
interconnect: Add imx core driver
dt-bindings: interconnect: Add bindings for imx8m noc
interconnect: Add devm_of_icc_get() as exported API for users
Loops-per-jiffies is a special number which represents a number of
noop-loop cycles per CPU-scheduler quantum - jiffies. As you
understand aside from CPU-specific implementation it depends on
the CPU frequency. So when a platform has the CPU frequency fixed,
we have no problem and the current udelay interface will work
just fine. But as soon as CPU-freq driver is enabled and the cores
frequency changes, we'll end up with distorted udelay's. In order
to fix this we have to accordinly adjust the per-CPU udelay_val
(the same as the global loops_per_jiffy) number. This can be done
in the CPU-freq transition event handler. We subscribe to that event
in the MIPS arch time-inititalization method.
Co-developed-by: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Signed-off-by: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
There are bit fields which persist in the MIPS CONFIG and CONFIG6
registers, but haven't been described in the generic mipsregs.h
header so far. In particular, the generic CONFIG bitfields are
BE - endian mode, BM - burst mode, SB - SimpleBE, OCP interface mode
indicator, UDI - user-defined "CorExtend" instructions, DSP - data
scratch pad RAM present, ISP - instruction scratch pad RAM present,
etc. The core-specific CONFIG6 bitfields are JRCD - jump register
cache prediction disable, R6 - MIPSr6 extensions enable, IFUPerfCtl -
IFU performance control, SPCD - sleep state performance counter, DLSB -
disable load/store bonding. A new exception code reported in the
ExcCode field of the Cause register: 30 - Parity/ECC error exception
happened on either fetch, load or cache refill. Lets add them to the
mipsregs.h header to be used in future platform code, which have them
utilized.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
CP0 config register may indicate whether write-through merging
is allowed. Currently there are two types of the merging available:
SysAD Valid and Full modes. Whether each of them are supported by
the core is implementation dependent. Moreover whether the ability
to change the mode also depends on the chip family instance. Taking
into account all of this we created a dedicated mm_config() method
to detect and enable merging if it's supported. It is called for
MIPS-type processors at CPU-probe stage and attempts to detect whether
the write merging is available. If it's known to be supported and
switchable, then switch on the full mode. Otherwise just perform the
CP0.Config.MM field analysis.
In addition there are platforms like InterAptiv/ProAptiv, which do have
the MM bit field set by default, but having write-through cacheing
unsupported makes write-merging also unsupported. In this case we just
ignore the MM field value.
Co-developed-by: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Signed-off-by: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Commit 1aeba347b3 ("MIPS: Hardcode cpu_has_mips* where target ISA
allows") updated the cpu_has_mips* macro to be replaced with a constant
expression where it's possible. By mistake it wasn't done correctly
for cpu_has_mips64r1/cpu_has_mips64r2 macro. They are defined to
be replaced with conditional expression __isa_range_or_flag(), which
means either ISA revision being within the range or the corresponding
CPU options flag was set at the probe stage or both being true at the
same time. But the ISA level value doesn't indicate whether the ISA is
MIPS32 or MIPS64. Due to this if we select MIPS32r1 - MIPS32r5
architectures the __isa_range() macro will activate the
cpu_has_mips64rX flags, which is incorrect. In order to fix the
problem we make sure the 64bits CPU support is enabled by means of
checking the flag cpu_has_64bits aside with proper ISA range and specific
Revision flag being set.
Fixes: 1aeba347b3 ("MIPS: Hardcode cpu_has_mips* where target ISA allows")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This is a MIPS32 Release 5 based IP core with XPA, EVA, dual/quad issue
exec pipes, MMU with two-levels TLB, UCA, MSA, MDU core level features
and system level features like up to six P5600 calculation cores, CM2
with L2 cache, IOCU/IOMMU (though might be unused depending on the
system-specific IP core configuration), GIC, CPC, virtualisation module,
eJTAG and PDtrace.
As being MIPS32 Release 5 based core it provides all the features
available by the CPU_MIPS32_R5 config, while adding a few more like
UCA attribute support, availability of CPU-freq (by means of L2/CM
clock ratio setting), EI/VI GIC modes detection at runtime.
In addition to this if P5600 architecture is enabled modern GNU GCC
provides a specific tuning for P5600 processors with respect to the
classic MIPS32 Release 5. First of all branch-likely avoidance is
activated only when the code is compiled with the speed optimization
(avoidance is always enabled for the pure MIPS32 Release 5
architecture). Secondly the madd/msub avoidance is enabled since
madd/msub utilization isn't profitable due to overhead of getting the
result out of the HI/LO registers. Multiply-accumulate instructions are
activated and utilized together with the necessary code reorder when
multiply-add/multiply-subtract statements are met. Finally load/store
bonding is activated by default. All of these optimizations may make
the code relatively faster than if just MIP32 release 5 architecture
was requested.
Co-developed-by: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Signed-off-by: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
There are five MIPS32/64 architecture releases currently available:
from 1 to 6 except fourth one, which was intentionally skipped.
Three of them can be called as major: 1st, 2nd and 6th, that not only
have some system level alterations, but also introduced significant
core/ISA level updates. The rest of the MIPS architecture releases are
minor.
Even though they don't have as much ISA/system/core level changes
as the major ones with respect to the previous releases, they still
provide a set of updates (I'd say they were intended to be the
intermediate releases before a major one) that might be useful for the
kernel and user-level code, when activated by the kernel or compiler.
In particular the following features were introduced or ended up being
available at/after MIPS32/64 Release 5 architecture:
+ the last release of the misaligned memory access instructions,
+ virtualisation - VZ ASE - is optional component of the arch,
+ SIMD - MSA ASE - is optional component of the arch,
+ DSP ASE is optional component of the arch,
+ CP0.Status.FR=1 for CP1.FIR.F64=1 (pure 64-bit FPU general registers)
must be available if FPU is implemented,
+ CP1.FIR.Has2008 support is required so CP1.FCSR.{ABS2008,NAN2008} bits
are available.
+ UFR/UNFR aliases to access CP0.Status.FR from user-space by means of
ctc1/cfc1 instructions (enabled by CP0.Config5.UFR),
+ CP0.COnfig5.LLB=1 and eretnc instruction are implemented to without
accidentally clearing LL-bit when returning from an interrupt,
exception, or error trap,
+ XPA feature together with extended versions of CPx registers is
introduced, which needs to have mfhc0/mthc0 instructions available.
So due to these changes GNU GCC provides an extended instructions set
support for MIPS32/64 Release 5 by default like eretnc/mfhc0/mthc0. Even
though the architecture alteration isn't that big, it still worth to be
taken into account by the kernel software. Finally we can't deny that
some optimization/limitations might be found in future and implemented
on some level in kernel or compiler. In this case having even
intermediate MIPS architecture releases support would be more than
useful.
So the most of the changes provided by this commit can be split into
either compile- or runtime configs related. The compile-time related
changes are caused by adding the new CONFIG_CPU_MIPS32_R5/CONFIG_CPU_MIPSR5
configs and concern the code activating MIPSR2 or MIPSR6 already
implemented features (like eretnc/LLbit, mthc0/mfhc0). In addition
CPU_HAS_MSA can be now freely enabled for MIPS32/64 release 5 based
platforms as this is done for CPU_MIPS32_R6 CPUs. The runtime changes
concerns the features which are handled with respect to the MIPS ISA
revision detected at run-time by means of CP0.Config.{AT,AR} bits. Alas
these fields can be used to detect either r1 or r2 or r6 releases.
But since we know which CPUs in fact support the R5 arch, we can manually
set MIPS_CPU_ISA_M32R5/MIPS_CPU_ISA_M64R5 bit of c->isa_level and then
use cpu_has_mips32r5/cpu_has_mips64r5 where it's appropriate.
Since XPA/EVA provide too complex alterationss and to have them used with
MIPS32 Release 2 charged kernels (for compatibility with current platform
configs) they are left to be setup as a separate kernel configs.
Co-developed-by: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Signed-off-by: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The else conditional expression is always true due to the if conditional
expression; remove it and add a comment to make it obvious still.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In function ice_set_mac_address, we will remove old dev_addr before
adding the new MAC. In the removing and adding process of the MAC,
there is no need to return error if the check finds the to-be-removed
dev_addr does not exist in the MAC filter list or the to-be-added mac
already exists, keep going or return success accordingly.
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move filter functions to separate file.
Add functions that prepare suitable ice_fltr_info struct
depending on the filter type and add this struct to earlier created
list:
- ice_fltr_add_mac_to_list
- ice_fltr_add_vlan_to_list
- ice_fltr_add_eth_to_list
This functions are used in adding and removing filters.
Create wrappers for functions mentioned above that alloc list,
add suitable ice_fltr_info to it and call add or remove function.
- ice_fltr_prepare_mac
- ice_fltr_prepare_mac_and_broadcast
- ice_fltr_prepare_vlan
- ice_fltr_prepare_eth
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Memory allocated in the ice_add_prof_id_vsig() function wasn't being
properly freed if an error occurred inside the for-loop in the function.
In particular, 'p' wasn't being freed if an error occurred before it was
added to the resource list at the end of the for-loop.
Signed-off-by: Eric Joyner <eric.joyner@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The vf_id variable is dealt with in the code in inconsistent
ways of sign usage, preventing compilation with -Werror=sign-compare.
Fix this problem in the code by always treating vf_id as unsigned, since
there are no valid values of vf_id that are negative.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change min() macros to min_t() which has compare type specified and it
helps avoid precision loss.
In some cases there was precision loss during calls or assignments.
Some fields in structs were unnecessarily large and gave multiple
warnings.
There were also some minor type differences which are now fixed as well as
some cases where a simple cast was needed.
Callers were were passing data that is a u16 to
ice_sched_cfg_node_bw_alloc() but the function was truncating that to a u8.
Fix that by changing the function to take a u16.
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When printing the ice status or AQ error codes, instead of printing out the
numerical value, provide the description of the error code. This provides
more info about the issue than a number.
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As soon as the driver registers the PF netdev, userspace utilities
like NetworkManager try to bring up the associated interface. When
this happens, the driver may not have finished initializing fully,
resulting in a bunch of errors in the interface up flow.
The driver already has a mechanism to indicate if it's not up yet;
by setting the __ICE_DOWN bit in pf->state, but this bit gets
cleared too early in the current flow. So clear this bit only when
the driver is fully up. Also check for the same bit in the ice_open
flow, and return -EBUSY if the bit is set.
Also in ice_open, replace references of vsi->back with a local
variable.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, the ice driver is setting a PHY configuration,
which causes a link drop, and then additionally it calls
for a nway_reset, which restarts auto-negotiation on the
link, which also causes a link drop. These two link
events in such close timing is causing the FW to not be
able to generate a link interrupt for the driver to
respond to.
Remove the unnecessary auto-negotiation restart from the
set pauseparams flow. Also remove error path that
would have performed an ice_down/ice_up as that is
also unnecessary.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current implementation for contiguous TC check
is assuming that the UPs will be mapped to TCs in
a linear progressing fashion. This is obviously
not always true.
Change the check to allow for various UP2TC mapping
configurations.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When there's a Tx timeout for a queue which belongs to a PFC enabled TC,
then it's not because the queue is hung but because PFC is in action.
In PFC, peer sends a pause frame for a specified period of time when its
buffer threshold is exceeded (due to congestion). Netdev on the other
hand checks if ACK is received within a specified time for a TX packet, if
not, it'll invoke the tx_timeout routine.
Signed-off-by: Avinash JD <avinash.dayanand@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement promiscuous support for VF VSIs. Behaviour of promiscuous support
is based on VF trust as well as the, introduced, vf-true-promisc flag.
A trusted VF with vf-true-promisc disabled will be the default VSI, which
means that all traffic without a matching destination MAC address in the
device's internal switch will be forwarded to this VF VSI.
A trusted VF with vf-true-promisc enabled will go into "true promiscuous
mode". This amounts to the VF receiving all ingress and egress traffic
that hits the device's internal switch.
An untrusted VF will only receive traffic destined for that VF.
The vf-true-promisc-support flag cannot be toggled while any VF is in
promiscuous mode. This flag should be set prior to loading the iavf driver
or spawning VF(s).
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Create a boost TCAM entry for each tunnel port in order to get a tunnel
PTYPE. Update netdev feature flags and implement the appropriate logic to
get and set values for hardware offloads.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
