If CONFIG_ARCH_ROCKCHIP is not set but COMPILE_TEST is set, the file in
the subdir rockchip can not be built due to CONFIG_ARCH_ROCKCHIP check
in drivers/phy/Makefile.
Since the related configs in drivers/phy/rockchip/Kconfig depend on
ARCH_ROCKCHIP, so remove CONFIG_ARCH_ROCKCHIP check for subdir rockchip
in drivers/phy/Makefile.
The other CONFIG_ARCH_* about allwinner, amlogic, mediatek, renesas and
tegra have the same situation, so remove them too.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/1590412138-13903-2-git-send-email-yangtiezhu@loongson.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
clk_div_table and wiz_regmap_config are not modified and can therefore
be made const to allow the compiler to put them in read-only memory.
Before:
text data bss dec hex filename
20265 7044 64 27373 6aed drivers/phy/ti/phy-j721e-wiz.o
After:
text data bss dec hex filename
20649 6660 64 27373 6aed drivers/phy/ti/phy-j721e-wiz.o
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200524095516.25227-3-rikard.falkeborn@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
regmap_config is not modified and can be made static to allow the compiler
to put it in read-only memory.
Before:
text data bss dec hex filename
12328 3644 64 16036 3ea4 drivers/phy/ti/phy-am654-serdes.o
After:
text data bss dec hex filename
12648 3324 64 16036 3ea4 drivers/phy/ti/phy-am654-serdes.o
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200524095516.25227-2-rikard.falkeborn@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The USB-audio mixer code holds a linked list of usb_mixer_elem_list,
and several operations are performed for each mixer element. A few of
them (snd_usb_mixer_notify_id() and snd_usb_mixer_interrupt_v2())
assume each mixer element being a usb_mixer_elem_info object that is a
subclass of usb_mixer_elem_list, cast via container_of() and access it
members. This may result in an out-of-bound access when a
non-standard list element has been added, as spotted by syzkaller
recently.
This patch adds a new field, is_std_info, in usb_mixer_elem_list to
indicate that the element is the usb_mixer_elem_info type or not, and
skip the access to such an element if needed.
Reported-by: syzbot+fb14314433463ad51625@syzkaller.appspotmail.com
Reported-by: syzbot+2405ca3401e943c538b5@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200624122340.9615-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 87676cfca1 ("arm64: vdso: Disable dwarf unwinding through the
sigreturn trampoline") unconditionally passes the '--no-eh-frame-hdr'
option to the linker when building the native vDSO in an attempt to
prevent generation of the .eh_frame_hdr section, the presence of which
has been implicated in segfaults originating from the libgcc unwinder.
Unfortunately, not all versions of binutils support this option, which
has been shown to cause build failures in linux-next:
| CALL scripts/atomic/check-atomics.sh
| CALL scripts/checksyscalls.sh
| LD arch/arm64/kernel/vdso/vdso.so.dbg
| ld: unrecognized option '--no-eh-frame-hdr'
| ld: use the --help option for usage information
| arch/arm64/kernel/vdso/Makefile:64: recipe for target
| 'arch/arm64/kernel/vdso/vdso.so.dbg' failed
| make[1]: *** [arch/arm64/kernel/vdso/vdso.so.dbg] Error 1
| arch/arm64/Makefile:175: recipe for target 'vdso_prepare' failed
| make: *** [vdso_prepare] Error 2
Only link the vDSO with '--no-eh-frame-hdr' when the linker supports it.
If we end up with the section due to linker defaults, the absence of CFI
information in the sigreturn trampoline will prevent the unwinder from
breaking.
Link: https://lore.kernel.org/r/7a7e31a8-9a7b-2428-ad83-2264f20bdc2d@hisilicon.com
Fixes: 87676cfca1 ("arm64: vdso: Disable dwarf unwinding through the sigreturn trampoline")
Reported-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Will Deacon <will@kernel.org>
clang points out that a local variable is initialized with
an enum value of the wrong type:
drivers/phy/intel/phy-intel-combo.c:202:34: error: implicit conversion from enumeration type 'enum intel_phy_mode' to different enumeration type 'enum intel_combo_mode' [-Werror,-Wenum-conversion]
enum intel_combo_mode cb_mode = PHY_PCIE_MODE;
~~~~~~~ ^~~~~~~~~~~~~
>From reading the code, it seems that this was not only the
wrong type, but not even supposed to be a code path that can
happen in practice.
Change the code to have no default phy mode but instead return an
error for invalid input.
Fixes: ac0a95a3ea ("phy: intel: Add driver support for ComboPhy")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Dilip Kota <eswara.kota@linux.intel.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://lore.kernel.org/r/20200527134518.908624-1-arnd@arndb.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
FIELD_PREP expects constant arguments. Istead of doing FIELD_PREP
operation on the arguments of combo_phy_w32_off_mask(), pass the
final FIELD_PREP value as an argument.
Error reported as:
In file included from include/linux/build_bug.h:5,
from include/linux/bitfield.h:10,
from drivers/phy/intel/phy-intel-combo.c:8:
drivers/phy/intel/phy-intel-combo.c: In function 'combo_phy_w32_off_mask':
include/linux/bitfield.h:52:28: warning: comparison is always false due to limited range of data type [-Wtype-limits]
include/linux/compiler.h:350:38: error: call to '__compiletime_assert_37' declared with attribute error: FIELD_PREP: mask is not constant
94 | __BF_FIELD_CHECK(_mask, 0ULL, _val, "FIELD_PREP: "); | ^~~~~~~~~~~~~~~~
drivers/phy/intel/phy-intel-combo.c:137:13: note: in expansion of macro 'FIELD_PREP'
137 | reg_val |= FIELD_PREP(mask, val);
| ^~~~~~~~~~
../include/linux/compiler.h:392:38: error: call to__compiletime_assert_137
declared with attribute error:
BUILD_BUG_ON failed: (((mask) + (1ULL << (__builtin_ffsll(mask) - 1))) & (((mask) + (1ULL << (__builtin_ffsll(mask) - 1))) - 1)) != 0
_compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
../include/linux/bitfield.h:94:3: note: in expansion of macro __BF_FIELD_CHECK
__BF_FIELD_CHECK(_mask, 0ULL, _val, "FIELD_PREP: "); \
^~~~~~~~~~~~~~~~
../drivers/phy/intel/phy-intel-combo.c:137:13: note: in expansion of macro FIELD_PREP
reg_val |= FIELD_PREP(mask, val);
^~~~~~~~~~
Fixes: ac0a95a3ea ("phy: intel: Add driver support for ComboPhy")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Dilip Kota <eswara.kota@linux.intel.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Link: https://lore.kernel.org/r/8a309dd3c238efbaa59d1649704255d6f8b6c9c5.1590575358.git.eswara.kota@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Maor Gottlieb says:
====================
The following series adds support to get the RDMA resource data in RAW
format. The main motivation for doing this is to enable vendors to return
the entire QP/CQ/MR data without a need from the vendor to set each
field separately.
====================
Based on the mlx5-next branch at
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
due to dependencies
* branch 'raw_dumps':
RDMA/mlx5: Add support to get MR resource in RAW format
RDMA/mlx5: Add support to get CQ resource in RAW format
RDMA/mlx5: Add support to get QP resource in RAW format
RDMA: Add support to dump resource tracker in RAW format
RDMA: Add dedicated CM_ID resource tracker function
RDMA: Add dedicated QP resource tracker function
RDMA: Add a dedicated CQ resource tracker function
RDMA: Add dedicated MR resource tracker function
RDMA/core: Don't call fill_res_entry for PD
net/mlx5: Add support in query QP, CQ and MKEY segments
net/mlx5: Export resource dump interface
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Add support to get resource dump in raw format. It enable drivers to
return the entire device specific QP/CQ/MR context without a need from the
driver to set each field separately.
The raw query returns only the device specific data, general data is still
returned by using the existing queries.
Example:
$ rdma res show mr dev mlx5_1 mrn 2 -r -j
[{"ifindex":7,"ifname":"mlx5_1",
"data":[0,4,255,254,0,0,0,0,0,0,0,0,16,28,0,216,...]}]
Link: https://lore.kernel.org/r/20200623113043.1228482-9-leon@kernel.org
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
All config options for GPIO drivers are inside a big "if GPIOLIB ...
endif" block, so there is no reason for individual config options to
have expicit dependencies on GPIOLIB. Hence remove them.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add PMC gpio support.
Only bank 0,1, 3 and 4 are connected to the multiplexed Input output
pins. Bank 0 and 1 to mio and bank 3 and 4 to extended multiplexed input
output pins.
Versal devices are the industry's first adaptive compute
acceleration platforms.
https://www.xilinx.com/support/documentation/data_sheets/ds950-versal-overview.pdf
On the Versal platform, we are using two customized GPIO controllers(IP)
which were used in Zynq/ZynqMp platform.
One of them present in the Platform Management Controller(PMC) block and
other in Processing System(PS) block.
In PMC_GPIO only Bank0,1,3 & 4 are enabled and in PS_GPIO only
Bank 0 & 3 are enabled.
You can find more details of GPIO IP in ZynqMP TRM General Purpose
I/O(Chapter-27).
https://www.xilinx.com/support/documentation/user_guides/ug1085-zynq-ultrascale-trm.pdf
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
If gpio is not set to wake disable the interrupt. ATF set all slaves with
enabled interrupts as wakeup sources and if gpio is used in r5 then it
wakes up linux.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add Versal support in gpio.
Only bank 0 and 3 are connected to the Multiplexed Input output pins.
Bank 0 to mio and bank3 to fabric Multiplexed input output pins.
Versal devices are the industry's first adaptive compute
acceleration platforms.
https://www.xilinx.com/support/documentation/data_sheets/ds950-versal-overview.pdf
On the Versal platform, we are using two customized GPIO controllers(IP)
which were used in Zynq/ZynqMp platform.
One of them present in the Platform Management Controller(PMC) block and
other in Processing System(PS) block.
In PMC_GPIO only Bank0,1,3 & 4 are enabled and in PS_GPIO only
Bank 0 & 3 are enabled.
You can find more details of GPIO IP in ZynqMP TRM General Purpose
I/O(Chapter-27).
https://www.xilinx.com/support/documentation/user_guides/ug1085-zynq-ultrascale-trm.pdf
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Drop CLK_IS_CRITICAL from fclk_div2. This was added because we didn't
know the relation between this clock and RGMII Ethernet. It turns out
that fclk_div2 is used as "timing adjustment clock" to generate the RX
delay on the MAC side - which was enabled by u-boot on Odriod-C1. When
using the RX delay on the PHY side or not using a RX delay at all then
this clock can be disabled.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200620161422.24114-1-martin.blumenstingl@googlemail.com
Fix race condition when changing the direction (in/out) of the GPIO pin.
The read-modify-write sequence (as coded in the driver) isn't atomic and
requires synchronization (spinlock).
Signed-off-by: Glenn Langedock <Glenn.Langedock@barco.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
In GAUDI the current timer value for the hardware to check if it is
in IDLE state is too low. As a result, there are occasions where the H/W
wrongly reports it is not IDLE. The driver checks that before submitting
work on behalf of the driver during initialization, so a false report might
cause the driver to fail during device initialization.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
As this is a cypress HID->COM RS232 style device that is handled
by the cypress_M8 driver we also need to add it to the ignore list
in hid-quirks.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: James Hilliard <james.hilliard1@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Maxxter KB-BT-001 Bluetooth keyboard, which looks somewhat like the
Apple Wireless Keyboard, is using the vendor and product IDs (05AC:0239)
of the Apple Wireless Keyboard (2009 ANSI version) <sigh>.
But its F1 - F10 keys are marked as sending F1 - F10, not the special
functions hid-apple.c maps them too; and since its descriptors do not
contain the HID_UP_CUSTOM | 0x0003 usage apple-hid looks for for the
Fn-key, apple_setup_input() never gets called, so F1 - F6 are mapped
to key-codes which have not been set in the keybit array causing them
to not send any events at all.
The lack of a usage code matching the Fn key in the clone is actually
useful as this allows solving this problem in a generic way.
This commits adds a fn_found flag and it adds a input_configured
callback which checks if this flag is set once all usages have been
mapped. If it is not set, then assume this is a clone and clear the
quirks bitmap so that the hid-apple code does not add any special
handling to this keyboard.
This fixes F1 - F6 not sending anything at all and F7 - F12 sending
the wrong codes on the Maxxter KB-BT-001 Bluetooth keyboard and on
similar clones.
Cc: Joao Moreno <mail@joaomoreno.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
According to the datasheet of pl330:
Example 2-1 Using DMAGO with the debug instruction registers
1. Create a program for the DMA channel
2. Store the program in a region of system memory
3. Poll the DBGSTATUS Register to ensure that the debug is idle
4. Write to the DBGINST0 Register
5. Write to the DBGINST1 Register
6. Write zero to the DBGCMD Register
so, we should make sure the debug is idle before step 4/5/6, not
only step 6. if not, there maybe a risk that fail to write DBGINST0/1.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Link: https://lore.kernel.org/r/1591234598-78919-1-git-send-email-sugar.zhang@rock-chips.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
My last name changed to "Rheinsberg", so update the maintainer entries
and adjust the emails while at it.
Signed-off-by: David Rheinsberg <david.rheinsberg@gmail.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On Toradex Colibri VF50 (Vybrid VF5xx) with fsl-edma driver NULL pointer
exception happens occasionally on serial output initiated by login
timeout.
This was reproduced only if kernel was built with significant debugging
options and EDMA driver is used with serial console.
Issue looks like a race condition between interrupt handler
fsl_edma_tx_handler() (called as a result of fsl_edma_xfer_desc()) and
terminating the transfer with fsl_edma_terminate_all().
The fsl_edma_tx_handler() handles interrupt for a transfer with already
freed edesc and idle==true.
The mcf-edma driver shares design and lot of code with fsl-edma. It
looks like being affected by same problem. Fix this pattern the same
way as fix for fsl-edma driver.
Fixes: e7a3ff92ea ("dmaengine: fsl-edma: add ColdFire mcf5441x edma support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Robin Gong <yibin.gong@nxp.com>
Link: https://lore.kernel.org/r/1591881665-25592-1-git-send-email-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
NULL pointer exception happens occasionally on serial output initiated
by login timeout. This was reproduced only if kernel was built with
significant debugging options and EDMA driver is used with serial
console.
col-vf50 login: root
Password:
Login timed out after 60 seconds.
Unable to handle kernel NULL pointer dereference at virtual address 00000044
Internal error: Oops: 5 [#1] ARM
CPU: 0 PID: 157 Comm: login Not tainted 5.7.0-next-20200610-dirty #4
Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
(fsl_edma_tx_handler) from [<8016eb10>] (__handle_irq_event_percpu+0x64/0x304)
(__handle_irq_event_percpu) from [<8016eddc>] (handle_irq_event_percpu+0x2c/0x7c)
(handle_irq_event_percpu) from [<8016ee64>] (handle_irq_event+0x38/0x5c)
(handle_irq_event) from [<801729e4>] (handle_fasteoi_irq+0xa4/0x160)
(handle_fasteoi_irq) from [<8016ddcc>] (generic_handle_irq+0x34/0x44)
(generic_handle_irq) from [<8016e40c>] (__handle_domain_irq+0x54/0xa8)
(__handle_domain_irq) from [<80508bc8>] (gic_handle_irq+0x4c/0x80)
(gic_handle_irq) from [<80100af0>] (__irq_svc+0x70/0x98)
Exception stack(0x8459fe80 to 0x8459fec8)
fe80: 72286b00 e3359f64 00000001 0000412d a0070013 85c98840 85c98840 a0070013
fea0: 8054e0d4 00000000 00000002 00000000 00000002 8459fed0 8081fbe8 8081fbec
fec0: 60070013 ffffffff
(__irq_svc) from [<8081fbec>] (_raw_spin_unlock_irqrestore+0x30/0x58)
(_raw_spin_unlock_irqrestore) from [<8056cb48>] (uart_flush_buffer+0x88/0xf8)
(uart_flush_buffer) from [<80554e60>] (tty_ldisc_hangup+0x38/0x1ac)
(tty_ldisc_hangup) from [<8054c7f4>] (__tty_hangup+0x158/0x2bc)
(__tty_hangup) from [<80557b90>] (disassociate_ctty.part.1+0x30/0x23c)
(disassociate_ctty.part.1) from [<8011fc18>] (do_exit+0x580/0xba0)
(do_exit) from [<801214f8>] (do_group_exit+0x3c/0xb4)
(do_group_exit) from [<80121580>] (__wake_up_parent+0x0/0x14)
Issue looks like race condition between interrupt handler fsl_edma_tx_handler()
(called as result of fsl_edma_xfer_desc()) and terminating the transfer with
fsl_edma_terminate_all().
The fsl_edma_tx_handler() handles interrupt for a transfer with already freed
edesc and idle==true.
Fixes: d6be34fbd3 ("dma: Add Freescale eDMA engine driver support")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Robin Gong <yibin.gong@nxp.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1591877861-28156-2-git-send-email-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In commit ed17b8d377 ("xfrm: fix a warning in xfrm_policy_insert_list"),
it would take 'priority' to make a policy unique, and allow duplicated
policies with different 'priority' to be added, which is not expected
by userland, as Tobias reported in strongswan.
To fix this duplicated policies issue, and also fix the issue in
commit ed17b8d377 ("xfrm: fix a warning in xfrm_policy_insert_list"),
when doing add/del/get/update on user interfaces, this patch is to change
to look up a policy with both mark and mask by doing:
mark.v == pol->mark.v && mark.m == pol->mark.m
and leave the check:
(mark & pol->mark.m) == pol->mark.v
for tx/rx path only.
As the userland expects an exact mark and mask match to manage policies.
v1->v2:
- make xfrm_policy_mark_match inline and fix the changelog as
Tobias suggested.
Fixes: 295fae5688 ("xfrm: Allow user space manipulation of SPD mark")
Fixes: ed17b8d377 ("xfrm: fix a warning in xfrm_policy_insert_list")
Reported-by: Tobias Brunner <tobias@strongswan.org>
Tested-by: Tobias Brunner <tobias@strongswan.org>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
If this is in "transceiver" mode the the ->qwork isn't required and is
a NULL pointer. This can lead to a NULL dereference when we call
destroy_workqueue(udc->qwork).
Fixes: 3517c31a8e ("usb: gadget: mv_udc: use devm_xxx for probe")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The current number of KVM_IRQCHIP_NUM_PINS results in an order 3
allocation (32kb) for each guest start/restart which can result in OOM
killer activity when kernel memory is fragmented enough.
This fix reduces the number of iopins as s390 doesn't use them, hence
reducing the memory footprint.
In the function tegra_usb_phy_probe(), if usb_add_phy_dev() failed,
the return value will be given to err, and if usb_add_phy_dev() succeed,
the return value will be zero. Thus it is unnecessary to repeated check
here.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
dwc3_pci_resume_work() calls pm_runtime_get_sync() that increments
the reference counter. In case of failure, decrement the reference
before returning.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The other thread may access other endpoints when the cdns3_check_new_setup
is handling, add spinlock to protect it.
Cc: <stable@vger.kernel.org>
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
It should use the correct direction value from register, not depends
on previous software setting. It fixed the EP number wrong issue at
trace when the TRBERR interrupt occurs for EP0IN.
When the EP0IN IOC has finished, software prepares the setup packet
request, the expected direction is OUT, but at that time, the TRBERR
for EP0IN may occur since it is DMULT mode, the DMA does not stop
until TRBERR has met.
Cc: <stable@vger.kernel.org>
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
