It is observed that sometimes when sdiod is low in tx credits in low
rssi scenarios, the data path consumes all sdiod rx all credits and
there is no sdiod rx credit available for control path causing host
and card to go out of sync resulting in link loss between host and
card. So in order to prevent it some credits are reserved for control
path.
Note that TXCTL_CREDITS can't be larger than the firmware default
credit update threshold 2; otherwise there will be a deadlock for both
side waiting for each other.
Signed-off-by: Amar Shankar <amsr@cypress.com>
Signed-off-by: Jia-Shyr Chuang <joseph.chuang@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200610152106.175257-4-chi-hsien.lin@cypress.com
As we did in the last 2 patches for vti(6), this patch is to define a
new xfrm_tunnel object 'xfrmi_ipip6_handler' to register for AF_INET6,
and a new xfrm6_tunnel object 'xfrmi_ip6ip_handler' to register for
AF_INET.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
An xfrm6_tunnel object is linked into the list when registering,
so vti_ipv6_handler can not be registered twice, otherwise its
next pointer will be overwritten on the second time.
So this patch is to define a new xfrm6_tunnel object to register
for AF_INET.
Fixes: 2ab110cbb0 ("ip6_vti: support IP6IP tunnel processing")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
An xfrm_tunnel object is linked into the list when registering,
so vti_ipip_handler can not be registered twice, otherwise its
next pointer will be overwritten on the second time.
So this patch is to define a new xfrm_tunnel object to register
for AF_INET6.
Fixes: e6ce64570f ("ip_vti: support IPIP6 tunnel processing")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Eyal Birger says:
====================
When having many xfrm interfaces, the linear lookup of devices based on
if_id becomes costly.
The first patch refactors xfrmi_decode_session() to use the xi used in
the netdevice priv context instead of looking it up in the list based
on ifindex. This is needed in order to use if_id as the only key used
for xi lookup.
The second patch extends the existing infrastructure - which already
stores the xfrmi contexts in an array of lists - to use a hash of the
if_id.
Example benchmarks:
- running on a KVM based VM
- xfrm tunnel mode between two namespaces
- xfrm interface in one namespace (10.0.0.2)
Before this change set:
Single xfrm interface in namespace:
$ netperf -H 10.0.0.2 -l8 -I95,10 -t TCP_STREAM
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.2 () port 0 AF_INET : +/-5.000% @ 95% conf. : demo
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
131072 16384 16384 8.00 298.36
After adding 400 xfrmi interfaces in the same namespace:
$ netperf -H 10.0.0.2 -l8 -I95,10 -t TCP_STREAM
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.2 () port 0 AF_INET : +/-5.000% @ 95% conf. : demo
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
131072 16384 16384 8.00 221.77
After this patchset there was no observed change after adding the
xfrmi interfaces.
====================
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Gives us proper nonblocking support for free, and a pile of other
things. The tilcdc code is simply old enough that it was never
converted over, but was stuck forever with the copypasta from when it
was initially merged.
The riskiest thing with this conversion is maybe that there's an issue
with the vblank handling or vblank event handling, which will upset
the modern commit support in atomic helpers. But from a cursory review
drm_crtc_vblank_on/off is called in the right places, and the event
handling also seems to exist (albeit with much hand-rolling and
probably some races, could perhaps be converted over to
drm_crtc_arm_vblank_event without any real loss).
Motivated by me not having to hand-roll the dma-fence annotations for
this.
v2: Clear out crtc_state->event when we're handling the event, to
avoid upsetting the helpers (reported by Jyri).
v3: Also send out even whent the crtc is getting disabled. Tilcdc looks a
bit like conversion to simple display helpers would work out really
nice.
Tested-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200708142050.530240-1-daniel.vetter@ffwll.ch
Enable the CPUFREQ userspace governor in the tegra_defconfig so that
we can test CPUFREQ with the userspace governor with this configuration
on 32-bit Tegra devices.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Of the DPMS code, only ON and OFF states are used. Simplify mode setting
by moving both into separate functions and removing the rest.
The original code busy waited in the middle of updating the screen state
in SEQ1. To simplify the procedure, the new code busy waits first and then
updates SEQ1 in one chunk.
The DPMS code also set the LUT before enabling the screen. The patch moves
this code into the simple-display pipe's enable function.
v2:
* comment on SEQ1 updates in commit message
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200707082411.6583-5-tzimmermann@suse.de
The simple pipe's disable function disables the screen by calling
mgag200_disable_screen(). The simple pipe's enable function enables the
screen by calling mgag200_enable_display().
During modeset operations the screen is off and remains off. It's only
enabled after the modeset has been completed. Therefore remove all code
that sets or clears the <scroff> field while in modeset.
The related code also modifies the <syncrst> field in SEQ0. For now, keep
this code in place.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200707082411.6583-4-tzimmermann@suse.de
Use generic io accounting functions to manage io stats. There was an
attempt to do this earlier in commit 18c0b223cf ("md: use generic io
stats accounting functions to simplify io stat accounting"), but it did
not include a call to generic_end_io_acct() and caused issues with
tracking in-flight IOs, so it was later removed in commit 74672d069b
("md: fix md io stats accounting broken").
This patch attempts to fix this by using both disk_start_io_acct() and
disk_end_io_acct(). To make it possible, a struct md_io is allocated for
every new md bio, which includes the io start_time. A new mempool is
introduced for this purpose. We override bio->bi_end_io with our own
callback and call disk_start_io_acct() before passing the bio to
md_handle_request(). When it completes, we call disk_end_io_acct() and
the original bi_end_io callback.
This adds correct statistics about in-flight IOs and IO processing time,
interpreted e.g. in iostat as await, svctm, aqu-sz and %util.
It also fixes a situation where too many IOs where reported if a bio was
re-submitted to the mddev, because io accounting is now performed only
on newly arriving bios.
Acked-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Pointer mddev is being dereferenced with a test_bit call before mddev
is being null checked, this may cause a null pointer dereference. Fix
this by moving the null pointer checks to sanity check mddev before
it is dereferenced.
Addresses-Coverity: ("Dereference before null check")
Fixes: 62f7b1989c ("md raid0/linear: Mark array as 'broken' and fail BIOs if a member is gone")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Guilherme G. Piccoli <gpiccoli@canonical.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
When using the geni-serial as console, its important to be
able to hit the lowest possible power state in suspend,
even with no_console_suspend.
The only thing that prevents it today on platforms like the sc7180
is the interconnect BW votes, which we certainly don't need when
the system is in suspend. So in the suspend handler mark them as
ACTIVE_ONLY (0x3) and on resume switch them back to the ALWAYS tag (0x7)
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/1594704709-26072-1-git-send-email-rnayak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In modern Qualcomm platforms the mutex region of the TCSR is forked off
into its own block, all with a offset of 0 and stride of 4096, and in
some of these platforms no other registers in this region is accessed
from Linux.
Update the binding to allow the hardware block to be described directly
on the mmio bus, in addition to allowing the existing syscon based
definition for backwards compatibility.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200622075956.171058-3-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This is to fix lkp cppcheck warnings:
drivers/fpga/dfl-pci.c:230:6: warning: The scope of the variable 'ret' can be reduced. [variableScope]
int ret = 0;
^
drivers/fpga/dfl-pci.c:230:10: warning: Variable 'ret' is assigned a value that is never used. [unreadVariable]
int ret = 0;
^
Fixes: 3c2760b78f ("fpga: dfl: pci: fix return value of cci_pci_sriov_configure")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Acked-by: Wu Hao <hao.wu@intel.com>
Reviewed-by: Tom Rix <trix@redhat.com>
Signed-off-by: Moritz Fischer <mdf@kernel.org>
This driver maintains a version number which is cross-referenced in the
documentation (e.g. to indicate when features are added or changed) and
exposed through the responses to various SCSI commands. For example the
version number is use as the Product Revision number in standard SCSI
INQUIRY responses issued by this driver. The version date string is placed
in a vendor specific area in each standard SCSI INQUIRY response. This
patch bumps both.
Update the driver documentation URL that appears at the top of the driver
source file.
Link: https://lore.kernel.org/r/20200712182927.72044-3-dgilbert@interlog.com
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch simplifies, or at least makes more consistent, the way setting
the every_nth parameter injects errors. Here is a list of 'opts' flags and
in which cases they inject errors when abs(every_nth)%command_count == 0 is
reached:
- OPT_RECOVERED_ERR: issued on READ(*)s, WRITE(*)s and
WRITE_SCATTEREDs
- OPT_DIF_ERR: issued on READ(*)s, WRITE(*)s and
WRITE_SCATTEREDs
- OPT_DIX_ERR: issued on READ(*)s, WRITE(*)s and
WRITE_SCATTEREDs
- OPT_SHORT_TRANSFER: issued on READ(*)s
- OPT_TRANSPORT_ERR: issued on all commands
- OPT_CMD_ABORT: issued on all commands
The other uses of every_nth were not modified.
Previously if, for example, OPT_SHORT_TRANSFER was armed then if
(abs(every_nth) % command_count == 0) occurred during a command that was
_not_ a READ, then no error injection occurred. This behaviour puzzled
several testers. Now a global "inject_pending" flag is set and the _next_
READ will get hit and that flag is cleared. OPT_RECOVERED_ERR, OPT_DIF_ERR
and OPT_DIX_ERR have similar behaviour. A downside of this is that there
might be a hang-over pending injection that gets triggered by a following
test.
Also expand the every_nth runtime parameter so that it can take hex value
(i.e. with a leading '0x') as well as a decimal value. Now both the 'opts'
and the 'every_nth' runtime parameters can take hexadecimal values.
Link: https://lore.kernel.org/r/20200712182927.72044-2-dgilbert@interlog.com
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Many SCSI HBAs support a hostwide tagset, whereby each command submitted to
the HW from all submission queues must have a unique tag identifier.
Normally this unique tag will be in the range [0, max queue], where "max
queue" is the depth of each of the submission queues.
Add support for this hostwide tag feature, via module parameter
"host_max_queue". A non-zero value means that the feature is enabled. In
this case, the submission queues are not exposed to upper layer, i.e. from
blk-mq prespective, the device has a single hw queue. There are 2 reasons
for this:
a. It is assumed that the host can support nr_hw_queues * can_queue
commands, but this is not true for hostwide tags
b. For nr_hw_queues != 0, the request tag is not unique over all HW
queues, and some HBA drivers want to use this tag for the hostwide tag
However, like many SCSI HBA drivers today - megaraid sas being an example -
the full set of HW submission queues are still used in the LLDD driver. So
instead of using a complicated "reply_map" to create a per-CPU submission
queue mapping like megaraid_sas (as it depends on a PCI device + MSIs) -
use a simple algorithm:
hwq = cpu % queue count
If the host_max_queue param is set non-zero, then the max queue depth is
fixed at this value also.
If and when hostwide shared tags are supported in blk-mq/scsi mid-layer,
then the policy to set nr_hw_queues = 0 for hostwide tags can be revised.
Link: https://lore.kernel.org/r/1594297400-24756-3-git-send-email-john.garry@huawei.com
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
