This behavior is required in IPv6, and there is little need
to tolerate overlapping fragments in IPv4. This change
simplifies the code and eliminates potential DDoS attack vectors.
Tested: ran ip_defrag selftest (not yet available uptream).
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function zerocopy_from_iter() unmarks the 'end' in input sgtable while
adding new entries in it. The last entry in sgtable remained unmarked.
This results in KASAN error report on using apis like sg_nents(). Before
returning, the function needs to mark the 'end' in the last entry it
adds.
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Acked-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a ICMPV6_PKT_TOOBIG is received from a link local address the pmtu will
be updated on a route with an arbitrary interface index. Subsequent packets
sent back to the same link local address may therefore end up not
considering the updated pmtu.
Current behavior breaks TAHI v6LC4.1.4 Reduce PMTU On-link. Referring to RFC
1981: Section 3: "Note that Path MTU Discovery must be performed even in
cases where a node "thinks" a destination is attached to the same link as
itself. In a situation such as when a neighboring router acts as proxy [ND]
for some destination, the destination can to appear to be directly
connected but is in fact more than one hop away."
Using the interface index from the incoming ICMPV6_PKT_TOOBIG when updating
the pmtu.
Signed-off-by: Georg Kohmann <geokohma@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next tree:
1) Support for transparent proxying for nf_tables, from Mate Eckl.
2) Patchset to add OS passive fingerprint recognition for nf_tables,
from Fernando Fernandez. This takes common code from xt_osf and
place it into the new nfnetlink_osf module for codebase sharing.
3) Lightweight tunneling support for nf_tables.
4) meta and lookup are likely going to be used in rulesets, make them
direct calls. From Florian Westphal.
A bunch of incremental updates:
5) use PTR_ERR_OR_ZERO() from nft_numgen, from YueHaibing.
6) Use kvmalloc_array() to allocate hashtables, from Li RongQing.
7) Explicit dependencies between nfnetlink_cttimeout and conntrack
timeout extensions, from Harsha Sharma.
8) Simplify NLM_F_CREATE handling in nf_tables.
9) Removed unused variable in the get element command, from
YueHaibing.
10) Expose bridge hook priorities through uapi, from Mate Eckl.
And a few fixes for previous Netfilter batch for net-next:
11) Use per-netns mutex from flowtable event, from Florian Westphal.
12) Remove explicit dependency on iptables CT target from conntrack
zones, from Florian.
13) Fix use-after-free in rmmod nf_conntrack path, also from Florian.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It's legal to have 64 groups for netlink_sock.
As user-supplied nladdr->nl_groups is __u32, it's possible to subscribe
only to first 32 groups.
The check for correctness of .bind() userspace supplied parameter
is done by applying mask made from ngroups shift. Which broke Android
as they have 64 groups and the shift for mask resulted in an overflow.
Fixes: 61f4b23769 ("netlink: Don't shift with UB on nlk->ngroups")
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org
Reported-and-Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2018-08-05
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix bpftool percpu_array dump by using correct roundup to next
multiple of 8 for the value size, from Yonghong.
2) Fix in AF_XDP's __xsk_rcv_zc() to not returning frames back to
allocator since driver will recycle frame anyway in case of an
error, from Jakub.
3) Fix up BPF test_lwt_seg6local test cases to final iproute2
syntax, from Mathieu.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If a writer blocked condition is received without data, the current
consumer cursor is immediately sent. Servers could already receive this
condition in state SMC_INIT without finished tx-setup. This patch
avoids sending a consumer cursor update in this case.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
variable 'err' is unmodified after initalization,
so simply cleans up it and returns 0.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Applications use -ECONNREFUSED as returned from write() in order to
determine that a socket should be closed. However, when using connected
dgram unix sockets in a poll/write loop, a final POLLOUT event can be
missed when the remote end closes. Thus, the poll is stuck forever:
thread 1 (client) thread 2 (server)
connect() to server
write() returns -EAGAIN
unix_dgram_poll()
-> unix_recvq_full() is true
close()
->unix_release_sock()
->wake_up_interruptible_all()
unix_dgram_poll() (due to the
wake_up_interruptible_all)
-> unix_recvq_full() still is true
->free all skbs
Now thread 1 is stuck and will not receive anymore wakeups. In this
case, when thread 1 gets the -EAGAIN, it has not queued any skbs
otherwise the 'free all skbs' step would in fact cause a wakeup and
a POLLOUT return. So the race here is probably fairly rare because
it means there are no skbs that thread 1 queued and that thread 1
schedules before the 'free all skbs' step.
This issue was reported as a hang when /dev/log is closed.
The fix is to signal POLLOUT if the socket is marked as SOCK_DEAD, which
means a subsequent write() will get -ECONNREFUSED.
Reported-by: Ian Lance Taylor <iant@golang.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Rainer Weikusat <rweikusat@mobileactivedefense.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jason Baron <jbaron@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Push iov_iter up from rxrpc_kernel_recv_data() to its caller to allow
non-contiguous iovs to be passed down, thereby permitting file reading to
be simplified in the AFS filesystem in a future patch.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If 'session' is not NULL and is not a PPP pseudo-wire, then we fail to
drop the reference taken by l2tp_session_get().
Fixes: ecd012e45a ("l2tp: filter out non-PPP sessions in pppol2tp_tunnel_ioctl()")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the conntrack module is removed, we call nf_ct_iterate_destroy via
nf_ct_l4proto_unregister().
Problem is that nf_conntrack_proto_fini() gets called after the
conntrack hash table has already been freed.
Just remove the l4proto unregister call, its unecessary as the
nf_ct_protos[] array gets free'd right after anyway.
v2: add comment wrt. missing unreg call.
Fixes: a0ae2562c6 ("netfilter: conntrack: remove l3proto abstraction")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
connection tracking zones currently depend on the xtables CT target.
The reasoning was that it makes no sense to support zones if they can't
be configured (which needed CT target).
Nowadays zones can also be used by OVS and configured via nftables,
so remove the dependency.
connection tracking labels are handled via hidden dependency that gets
auto-selected by the connlabel match.
Make it a visible knob, as labels can be attached via ctnetlink
or via nftables rules (nft_ct expression) too.
This allows to use conntrack labels and zones with nftables-only build.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
* From nf_tables_newchain(), codepath provides context that allows us to
infer if we are updating a chain (in that case, no module autoload is
required) or adding a new one (then, module autoload is indeed
needed).
* We only need it in one single spot in nf_tables_newrule().
* Not needed for nf_tables_newset() at all.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Netfilter exposes standard hook priorities in case of ipv4, ipv6 and
arp but not in case of bridge.
This patch exposes the hook priority values of the bridge family (which are
different from the formerly mentioned) via uapi so that they can be used by
user-space applications just like the others.
Signed-off-by: Máté Eckl <ecklm94@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch allows us to match on the tunnel metadata that is available
of the packet. We can use this to validate if the packet comes from/goes
to tunnel and the corresponding tunnel ID.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch implements the tunnel object type that can be used to
configure tunnels via metadata template through the existing lightweight
API from the ingress path.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
A config check was missing form the code when using
nf_defrag_ipv6_enable with NFT_TPROXY != n and NF_DEFRAG_IPV6 = n and
this caused the following error:
../net/netfilter/nft_tproxy.c: In function 'nft_tproxy_init':
../net/netfilter/nft_tproxy.c:237:3: error: implicit declaration of function
+'nf_defrag_ipv6_enable' [-Werror=implicit-function-declaration]
err = nf_defrag_ipv6_enable(ctx->net);
This patch adds a check for NF_TABLES_IPV6 when NF_DEFRAG_IPV6 is
selected by Kconfig.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Fixes: 4ed8eb6570 ("netfilter: nf_tables: Add native tproxy support")
Signed-off-by: Máté Eckl <ecklm94@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This attribute's handling is broken. It can only be used when creating
Ethernet pseudo-wires, in which case its value can be used as the
initial MTU for the l2tpeth device.
However, when handling update requests, L2TP_ATTR_MTU only modifies
session->mtu. This value is never propagated to the l2tpeth device.
Dump requests also return the value of session->mtu, which is not
synchronised anymore with the device MTU.
The same problem occurs if the device MTU is properly updated using the
generic IFLA_MTU attribute. In this case, session->mtu is not updated,
and L2TP_ATTR_MTU will report an invalid value again when dumping the
session.
It does not seem worthwhile to complexify l2tp_eth.c to synchronise
session->mtu with the device MTU. Even the ip-l2tp manpage advises to
use 'ip link' to initialise the MTU of l2tpeth devices (iproute2 does
not handle L2TP_ATTR_MTU at all anyway). So let's just ignore it
entirely.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The value of the session's .mtu field, as defined by
pppol2tp_connect() or pppol2tp_session_create(), is later overwritten
by pppol2tp_session_init() (unless getting the tunnel's socket PMTU
fails). This field is then only used when setting the PPP channel's MTU
in pppol2tp_connect().
Furthermore, the SIOC[GS]IFMTU ioctls only act on the session's .mtu
without propagating this value to the PPP channel, making them useless.
This patch initialises the PPP channel's MTU directly and ignores the
session's .mtu entirely. MTU is still computed by subtracting the
PPPOL2TP_HEADER_OVERHEAD constant. It is not optimal, but that doesn't
really matter: po->chan.mtu is only used when the channel is part of a
multilink PPP bundle. Running multilink PPP over packet switched
networks is certainly not going to be efficient, so not picking the
best MTU does not harm (in the worst case, packets will just be
fragmented by the underlay).
The SIOC[GS]IFMTU ioctls are removed entirely (as opposed to simply
ignored), because these ioctls commands are part of the requests that
should be handled generically by the socket layer. PX_PROTO_OL2TP was
the only socket type abusing these ioctls.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidate retrieval of tunnel's socket mtu in order to simplify
l2tp_eth and l2tp_ppp a bit.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this, remove ifdef for CONFIG_NF_CONNTRACK_TIMEOUT in
nfnetlink_cttimeout. This is also required for moving ctnl_untimeout
from nfnetlink_cttimeout to nf_conntrack_timeout.
Signed-off-by: Harsha Sharma <harshasharmaiitr@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Variable 'ext' is being assigned but are never used hence they are
unused and can be removed.
Cleans up clang warnings:
net/netfilter/nf_tables_api.c:4032:28: warning: variable ‘ext’ set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The use of SKCIPHER_REQUEST_ON_STACK() will trigger FRAME_WARN warnings
(when less than 2048) once the VLA is no longer hidden from the check:
net/rxrpc/rxkad.c:398:1: warning: the frame size of 1152 bytes is larger than 1024 bytes [-Wframe-larger-than=]
net/rxrpc/rxkad.c:242:1: warning: the frame size of 1152 bytes is larger than 1024 bytes [-Wframe-larger-than=]
This passes the initial SKCIPHER_REQUEST_ON_STACK allocation to the leaf
functions for reuse. Two requests allocated on the stack is not needed
when only one is used at a time.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
User was able to perform filter flush on chain 0 even if it didn't have
any filters in it. With the patch that avoided implicit chain 0
creation, this changed. So in case user wants filter flush on chain
which does not exist, just return success. There's no reason for non-0
chains to behave differently than chain 0, so do the same for them.
Reported-by: Ido Schimmel <idosch@mellanox.com>
Fixes: f71e0ca4db ("net: sched: Avoid implicit chain 0 creation")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first client of the nf_osf.h userspace header is nft_osf, coming in
this batch, rename it to nfnetlink_osf.h as there are no userspace
clients for this yet, hence this looks consistent with other nfnetlink
subsystem.
Suggested-by: Jan Engelhardt <jengelh@inai.de>
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
nf_ct_alloc_hashtable is used to allocate memory for conntrack,
NAT bysrc and expectation hashtable. Assuming 64k bucket size,
which means 7th order page allocation, __get_free_pages, called
by nf_ct_alloc_hashtable, will trigger the direct memory reclaim
and stall for a long time, when system has lots of memory stress
so replace combination of __get_free_pages and vzalloc with
kvmalloc_array, which provides a overflow check and a fallback
if no high order memory is available, and do not retry to reclaim
memory, reduce stall
and remove nf_ct_free_hashtable, since it is just a kvfree
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: Wang Li <wangli39@baidu.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
All callers pass chain=0 to scatterwalk_crypto_chain().
Remove this unneeded parameter.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
We don't validate the address prefix lengths in the xfrm
selector we got from userspace. This can lead to undefined
behaviour in the address matching functions if the prefix
is too big for the given address family. Fix this by checking
the prefixes and refuse SA/policy insertation when a prefix
is invalid.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Air Icy <icytxw@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Allocate a temporary cgroup storage to use for bpf program test runs.
Because the test program is not actually attached to a cgroup,
the storage is allocated manually just for the execution
of the bpf program.
If the program is executed multiple times, the storage is not zeroed
on each run, emulating multiple runs of the program, attached to
a real cgroup.
Signed-off-by: Roman Gushchin <guro@fb.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The bpf_get_local_storage() helper function is used
to get a pointer to the bpf local storage from a bpf program.
It takes a pointer to a storage map and flags as arguments.
Right now it accepts only cgroup storage maps, and flags
argument has to be 0. Further it can be extended to support
other types of local storage: e.g. thread local storage etc.
Signed-off-by: Roman Gushchin <guro@fb.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This refactoring work has been started by David Howells in cdfbabfb2f
(net: Work around lockdep limitation in sockets that use sockets) but
the exact same day in 581319c586 (net/socket: use per af lockdep
classes for sk queues), Paolo Abeni added new classes.
This reduces the amount of (nearly) duplicated code and eases the
addition of new socket types.
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid scribbling over memory if the received reply/challenge is larger
than the buffer supplied with the authorizer.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Derive the signature from the entire buffer (both AES cipher blocks)
instead of using just the first half of the first block, leaving out
data_crc entirely.
This addresses CVE-2018-1129.
Link: http://tracker.ceph.com/issues/24837
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
When a client authenticates with a service, an authorizer is sent with
a nonce to the service (ceph_x_authorize_[ab]) and the service responds
with a mutation of that nonce (ceph_x_authorize_reply). This lets the
client verify the service is who it says it is but it doesn't protect
against a replay: someone can trivially capture the exchange and reuse
the same authorizer to authenticate themselves.
Allow the service to reject an initial authorizer with a random
challenge (ceph_x_authorize_challenge). The client then has to respond
with an updated authorizer proving they are able to decrypt the
service's challenge and that the new authorizer was produced for this
specific connection instance.
The accepting side requires this challenge and response unconditionally
if the client side advertises they have CEPHX_V2 feature bit.
This addresses CVE-2018-1128.
Link: http://tracker.ceph.com/issues/24836
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Will be used for encrypting both the initial and updated authorizers.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Will be used for decrypting the server challenge which is only preceded
by ceph_x_encrypt_header.
Drop struct_v check to allow for extending ceph_x_encrypt_header in the
future.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Will be used for sending ceph_msg_connect with an updated authorizer,
after the server challenges the initial authorizer.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
We already copy authorizer_reply_buf and authorizer_reply_buf_len into
ceph_connection. Factoring out __prepare_write_connect() requires two
more: authorizer_buf and authorizer_buf_len. Store the pointer to the
handshake in con->auth rather than piling on.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
The request mtime field is used all over ceph, and is currently
represented as a 'timespec' structure in Linux. This changes it to
timespec64 to allow times beyond 2038, modifying all users at the
same time.
[ Remove now redundant ts variable in writepage_nounlock(). ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
ceph_con_keepalive_expired() is the last user of timespec_add() and some
of the last uses of ktime_get_real_ts(). Replacing this with timespec64
based interfaces lets us remove that deprecated API.
I'm introducing new ceph_encode_timespec64()/ceph_decode_timespec64()
here that take timespec64 structures and convert to/from ceph_timespec,
which is defined to have an unsigned 32-bit tv_sec member. This extends
the range of valid times to year 2106, avoiding the year 2038 overflow.
The ceph file system portion still uses the old functions for inode
timestamps, this will be done separately after the VFS layer is converted.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
There is no reason to continue option parsing after detecting
bad option.
[ Return match_int() errors from ceph_parse_options() to match the
behaviour of parse_rbd_opts_token() and parse_fsopt_token(). ]
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
