As per the display enable sequence, we need to follow the enable sequence
for slaves first with DP_TP_CTL set to Idle and configure the transcoder
port sync register to select the corersponding master, then follow the
enable sequence for master leaving DP_TP_CTL to idle.
At this point the transcoder port sync mode is configured and enabled
and the Vblanks of both ports are synchronized so then set DP_TP_CTL
for the slave and master to Normal and do post crtc enable updates.
v11:
* Rebase (Manasi)
v10:
* in trans sync mode, dont stop link train for tgl (Manasi)
v9:
Remove update_scanline_offset to rebase on Maarten's patch (Manasi)
v8:
* Rebase on Maarten's patches (Manasi)
v7:
* Use ffs(slaves) to get slave crtc (Ville)
v6:
* Modeset implies active_changed, remove one condition (Maarten)
v5:
* Fix checkpatch warning (Manasi)
v4:
* Reuse skl_commit_modeset_enables() hook (Maarten)
* Obtain slave crtc and states from master (Maarten)
v3:
* Rebase on drm-tip (Manasi)
v2:
* Create a icl_update_crtcs hook (Maarten, Danvet)
* This sequence only for CRTCs in trans port sync mode (Maarten)
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191018172725.1338-4-manasi.d.navare@intel.com
After the state is committed, we readout the HW registers and compare
the HW state with the SW state that we just committed.
For Transcdoer port sync, we add master_transcoder and the
salves bitmask to the crtc_state, hence we need to read those during
the HW state readout to avoid pipe state mismatch.
v11:
* Move master trans init to get pipe_Config hooks (Ville)
v10:
* Initialize master_tarnscoder readout for all platforms (Ville)
v9:
* Initialize master_transcoder = INVALID at get config (Ville)
v8:
* Use master_select -1, address TRANS_EDP case (Ville)
* Rename master_transcoder to _readout (Lucas)
v7:
* NDont read HW state for DSI
v6:
* Go through both parts of HW readout (Maarten)
* Add a WARN if the same trans configured as
master and slave (Ville, Maarten)
v5:
* Add return INVALID in defaut case (Maarten)
v4:
* Get power domains in master loop for get_config (Ville)
v3:
* Add TRANSCODER_D (Maarten)
* v3 Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
v2:
* Add Transcoder_D and MISSING_CASE (Maarten)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191018172725.1338-3-manasi.d.navare@intel.com
In case of tiled displays where different tiles are displayed across
different ports, we need to synchronize the transcoders involved.
This patch implements the transcoder port sync feature for
synchronizing one master transcoder with one or more slave
transcoders. This is only enbaled in slave transcoder
and the master transcoder is unaware that it is operating
in this mode.
This has been tested with tiled display connected to ICL.
v7:
* Rebase on Maarten's patches
v6:
* Use master_trans +1 and address missing trans_edp case (Ville)
v5:
* Add TRANSCODER_D case and MISSING_CASE (Maarten)
v4:
Rebase
v3:
* Check of DP_MST moved to atomic_check (Maarten)
v2:
* Do not use RMW, just write to the register in commit (Jani N)
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191018172725.1338-2-manasi.d.navare@intel.com
In case of tiled displays when the two tiles are sent across two CRTCs
over two separate DP SST connectors, we need a mechanism to synchronize
the two CRTCs and their corresponding transcoders.
So use the master-slave mode where there is one master corresponding
to last horizontal and vertical tile that needs to be genlocked with
all other slave tiles.
This patch identifies saves the master transcoder in all the slave
CRTC states. This is needed to select the master CRTC/transcoder
while configuring transcoder port sync for the corresponding slaves.
v6:
Rebase (manasi)
v5:
* Address Ville's comments
* Just pass crtc_state, no need to check GEN (Ville)
v4:
* Rebase
v3:
* Use master_tramscoder instead of master_crtc for valid
HW state readouts (Ville)
v2:
* Move this to intel_mode_set_pipe_config(Jani N, Ville)
* Use slave_bitmask to save associated slaves in master crtc state (Ville)
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191018172725.1338-1-manasi.d.navare@intel.com
Commit 2d6f6f359f ("drm/i915: add i915_driver_modeset_remove()")
claimed removal of asymmetry in probe() and remove() calls, however, it
didn't take care of calling intel_irq_uninstall() on driver remove.
That doesn't hurt as long as we still call it from
intel_modeset_driver_remove() but in order to have full symmetry we
should call it again from i915_driver_modeset_remove().
Note that it's safe to call intel_irq_uninstall() twice thanks to
commit b318b82455 ("drm/i915: Nuke drm_driver irq vfuncs"). We may
only want to mention the case we are adding in a related FIXME comment
provided by that commit. While being at it, update the name of
function mentioned as calling it out of sequence as that name has been
changed meanwhile by commit 78dae1ac35 ("drm/i915: Propagate
"_remove" function name suffix down").
Suggested-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Janusz Krzysztofik <janusz.krzysztofik@linux.intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/6250061.7lZMOAyebC@jkrzyszt-desk.ger.corp.intel.com
Extract drm_mode_hdmi_vic() to correctly calculate the final HDMI
VIC for us. Currently this is being done a bit differently between
the AVI and HDMI infoframes. Let's get both to agree on this.
We need to allow the case where a mode is both 3D and has a HDMI
VIC. Currently we'll just refuse to generate the HDMI infoframe when
we really should be setting HDMI VIC to 0 and instead enabling 3D
stereo signalling.
If the sink doesn't even support the HDMI infoframe we should
not be picking the HDMI VIC in favor of the CEA VIC, because then
we'll end up not sending either VIC in the end.
Cc: Wayne Lin <waynelin@amd.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191004141914.20600-3-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
All the timeout values fit in u16, so let's shrink the structure
a bit.
This ends up actually increasing the .text size a bit due to
some changes in instructions (constant imul+small jmps replaced
with mov+bigger jmpqs). Seems pretty arbitrary to me so I'll
just pretend I didn't see it.
text data bss dec hex filename
- 34521 360 0 34881 8841 intel_hdmi.o
+ 34537 360 0 34897 8851 intel_hdmi.o
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191010145127.7487-5-ville.syrjala@linux.intel.com
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
The only reason for the timeout2 value in the array is the
HDCP_2_2_AKE_SEND_HPRIME message. But that one still needs
special casing inside the loop, and so just ends up making
the code harder to read. Let's just remove this leaky
timeout2 abstraction and special case that one command
in a way that is easy to understand. We can then remove the
timeout2 member from struct entirely.
text data bss dec hex filename
- 34633 360 0 34993 88b1 intel_hdmi.o
+ 34521 360 0 34881 8841 intel_hdmi.o
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191010145127.7487-4-ville.syrjala@linux.intel.com
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Unlike other planes the cursor currently handles 180 degree rotation
adjustment during the hardware programming phase. Let's move that
stuff into intel_cursor_check_surface() to match how we do things
with other plane types.
And while at we'll plop in the final src x/y coordinates (which will
actually always be zero) into the src rect and color_plane[0].x/y,
just for some extra consistency.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191015152757.12231-1-ville.syrjala@linux.intel.com
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Normally, we try and skip submission if ELSP[1] is filled. However, we
may desire to enable timeslicing due to the queue priority, even if
ELSP[1] itself does not require timeslicing. That is the queue is equal
priority to ELSP[0] and higher priority then ELSP[1]. Previously, we
would wait until the context switch to preempt the current ELSP[1], but
with timeslicing, we want to preempt ELSP[0] and replace it with the
queue.
In writing the test case, it become quickly apparent that we were also
suppressing the tasklet during promotion and so failing to notice when
the queue started requiring timeslicing.
Fixes: 2229adc813 ("drm/i915/execlist: Trim immediate timeslice expiry")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191018072027.31948-1-chris@chris-wilson.co.uk
Make the following items static to avoid clashes with
other parts of the kernel (dev_attr_core_id) or just
silence the following sparse warning:
drivers/gpu/drm/arm/malidp_drv.c:371:24: warning: symbol 'malidp_fb_create' was not declared. Should it be static?
drivers/gpu/drm/arm/malidp_drv.c:494:6: warning: symbol 'malidp_error_stats_dump' was not declared. Should it be static?
drivers/gpu/drm/arm/malidp_drv.c:668:1: warning: symbol 'dev_attr_core_id' was not declared. Should it be static?
Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191017111756.12861-1-ben.dooks@codethink.co.uk
Medium term goal is to eliminate the i915->engine[] array and to get there
we have recently introduced equivalent array in intel_gt. Now we need to
migrate the code further towards this state.
This next step is to eliminate usage of i915->engines[] from the
for_each_engine_masked iterator.
For this to work we also need to use engine->id as index when populating
the gt->engine[] array and adjust the default engine set indexing to use
engine->legacy_idx instead of assuming gt->engines[] indexing.
v2:
* Populate gt->engine[] earlier.
* Check that we don't duplicate engine->legacy_idx
v3:
* Work around the initialization order issue between default_engines()
and intel_engines_driver_register() which sets engine->legacy_idx for
now. It will be fixed properly later.
v4:
* Merge with forgotten v2.5.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191017161852.8836-1-tvrtko.ursulin@linux.intel.com
user_pages array should always be freed after validation regardless if
user pages are changed after bo is created because with HMM change parse
bo always allocate user pages array to get user pages for userptr bo.
v2: remove unused local variable and amend commit
v3: add back get user pages in gem_userptr_ioctl, to detect application
bug where an userptr VMA is not ananymous memory and reject it.
Bugzilla: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1844962
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Tested-by: Joe Barnett <thejoe@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.3
The locks (active.lock and rq->lock) need to be taken with disabled
interrupts. This is done in i915_request_retire() by disabling the
interrupts independently of the locks itself.
While local_irq_disable()+spin_lock() equals spin_lock_irq() on vanilla
it does not on PREEMPT_RT.
Chris Wilson confirmed that local_irq_disable() was just introduced as
an optimisation to avoid enabling/disabling interrupts during
lock/unlock combo.
Enable/disable interrupts as part of the locking instruction.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191017161352.e5z3ugse7gxl5ari@linutronix.de
