The datasheet of V3s (and various other chips) wrote
that TCON0_DCLK_DIV can be >= 1 if only dclk is used,
and must >= 6 if dclk1 or dclk2 is used. As currently
neither dclk1 nor dclk2 is used (no writes to these
bits), let's set minimal division to 1.
If this minimal division is 6, some common dot clock
frequencies can't be produced (e.g. 30MHz will not be
possible and will fallback to 25MHz), which is
obviously not an expected behaviour.
Signed-off-by: Yunhao Tian <t123yh@outlook.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/linux-arm-kernel/MN2PR08MB57905AD8A00C08DA219377C989760@MN2PR08MB5790.namprd08.prod.outlook.com/
Instead of fwnode_get_named_gpiod() that I plan to hide away, let's use
the new fwnode_gpiod_get_index() that mimics gpiod_get_index(), but
works with arbitrary firmware node.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to internal documents I found for CMP PCHs the PCI ID 0xA3C1
belongs to a CMP-V chipset. Based on the same docs the programming of
the PCH is compatible with that of KBP. Fix up my previous wrong
assumption accordingly using the SPT programming which in turn is the
basis for KBP.
The original bug reporter verified that this is the correct PCH
identification (the only way we'll program valid DDC pin-pair values to
the GMBUS register) and the Windows team uses the same identification
(that is using the KBP programming model for this PCH).
I filed the necessary Bspec update requests (BSpec/33734).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=112051
Fixes: 37c92dc303 ("drm/i915: Add new CNL PCH ID seen on a CML platform")
Reported-and-tested-by: Cyrus <cyrus.lien@canonical.com>
Cc: Cyrus <cyrus.lien@canonical.com>
Cc: Timo Aaltonen <tjaalton@ubuntu.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191112104608.24587-1-imre.deak@intel.com
The gem_ctx_persistence/smoketest was detecting an odd coherency issue
inside the LRC context image; that the address of the ring buffer did
not match our associated struct intel_ring. As we set the address into
the context image when we pin the ring buffer into place before the
context is active, that leaves the question of where did it get
overwritten. Either the HW context save occurred after our pin which
would imply that our idle barriers are broken, or we overwrote the
context image ourselves. It is only in reset_active() where we dabble
inside the context image outside of a serialised path from schedule-out;
but we could equally perform the operation inside schedule-in which is
then fully serialised with the context pin -- and remains serialised by
the engine pulse with kill_context(). (The only downside, aside from
doing more work inside the engine->active.lock, was the plan to merge
all the reset paths into doing their context scrubbing on schedule-out
needs more thought.)
Fixes: d12acee84f ("drm/i915/execlists: Cancel banned contexts on schedule-out")
Testcase: igt/gem_ctx_persistence/smoketest
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191111133205.11590-3-chris@chris-wilson.co.uk
(cherry picked from commit 31b61f0ef9)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Since CNP it's possible for rawclk to have two different values, 19.2
and 24 MHz. If the value indicated by SFUSE_STRAP register is different
from the power on default for PCH_RAWCLK_FREQ, we'll end up having a
mismatch between the rawclk hardware and software states after
suspend/resume. On previous platforms this used to work by accident,
because the power on defaults worked just fine.
Update the rawclk also on resume. The natural place to do this would be
intel_modeset_init_hw(), however VLV/CHV need it done before
intel_power_domains_init_hw(). Thus put it there even if it feels
slightly out of place.
v2: Call intel_update_rawclck() in intel_power_domains_init_hw() for all
platforms (Ville).
Reported-by: Shawn Lee <shawn.c.lee@intel.com>
Cc: Shawn Lee <shawn.c.lee@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Shawn Lee <shawn.c.lee@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191101142024.13877-1-jani.nikula@intel.com
(cherry picked from commit 59ed05ccdd)
Cc: <stable@vger.kernel.org> # v4.15+
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The anx6345 driver originally was copied from anx78xx.c, which has meanwhile
seen a few changes. In particular, the removal of drm_dp_link helpers and the
discontinuation to include drm_bridge.h from drm_crtc.h breaks compilation
in linux-5.5. Apply equivalents of these changes to anx6345.c.
Fixes: 6aa1926980 ("drm/bridge: Add Analogix anx6345 support")
Signed-off-by: Torsten Duwe <duwe@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20191112175940.GA13539@lst.de
On gen7, including Haswell, the MI_FLUSH_DW command is not synchronous
with the command streamer nor is there an option to make it so. To hide
this we add a large delay on the CS so that the breadcrumb should always
be visible before the interrupt. However, that does not seem to be
enough to ensure the memory is actually coherent with the read of the
breadcrumb. The breadcrumb update is a post-sync op... Throw in a
preliminary MI_FLUSH_DW before the breadcrumb update in the hope that
helps.
References: https://bugs.freedesktop.org/show_bug.cgi?id=112147
Testcase: igt/i915_selftest/live_blt
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191111120957.17732-1-chris@chris-wilson.co.uk
set_page_dirty says:
For pages with a mapping this should be done under the page lock
for the benefit of asynchronous memory errors who prefer a
consistent dirty state. This rule can be broken in some special
cases, but should be better not to.
Under those rules, it is only safe for us to use the plain set_page_dirty
calls for shmemfs/anonymous memory. Userptr may be used with real
mappings and so needs to use the locked version (set_page_dirty_lock).
However, following a try_to_unmap() we may want to remove the userptr and
so call put_pages(). However, try_to_unmap() acquires the page lock and
so we must avoid recursively locking the pages ourselves -- which means
that we cannot safely acquire the lock around set_page_dirty(). Since we
can't be sure of the lock, we have to risk skip dirtying the page, or
else risk calling set_page_dirty() without a lock and so risk fs
corruption.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=203317
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=112012
Fixes: 5cc9ed4b9a ("drm/i915: Introduce mapping of user pages into video memory (userptr) ioctl")
References: cb6d7c7dc7 ("drm/i915/userptr: Acquire the page lock around set_page_dirty()")
References: 505a8ec7e1 ("Revert "drm/i915/userptr: Acquire the page lock around set_page_dirty()"")
References: 6dcc693bc5 ("ext4: warn when page is dirtied without buffers")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191111133205.11590-1-chris@chris-wilson.co.uk
(cherry picked from commit 0d4bbe3d40)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Inside print_request(), we query the context/timeline name. Nothing
immediately protects the context from being freed if the request is
complete -- we rely on serialisation by the caller to keep the name
valid until they finish using it. Inside intel_engine_dump(), we
generally only print the requests in the execution queue protected by the
engine->active.lock, but we also show the pending execlists ports which
are not protected and so require a rcu_read_lock to keep the pointer
valid.
[ 1695.700883] BUG: KASAN: use-after-free in i915_fence_get_timeline_name+0x53/0x90 [i915]
[ 1695.700981] Read of size 8 at addr ffff8887344f4d50 by task gem_ctx_persist/2968
[ 1695.701068]
[ 1695.701156] CPU: 1 PID: 2968 Comm: gem_ctx_persist Tainted: G U 5.4.0-rc6+ #331
[ 1695.701246] Hardware name: Intel Corporation NUC7i5BNK/NUC7i5BNB, BIOS BNKBL357.86A.0052.2017.0918.1346 09/18/2017
[ 1695.701334] Call Trace:
[ 1695.701424] dump_stack+0x5b/0x90
[ 1695.701870] ? i915_fence_get_timeline_name+0x53/0x90 [i915]
[ 1695.701964] print_address_description.constprop.7+0x36/0x50
[ 1695.702408] ? i915_fence_get_timeline_name+0x53/0x90 [i915]
[ 1695.702856] ? i915_fence_get_timeline_name+0x53/0x90 [i915]
[ 1695.702947] __kasan_report.cold.10+0x1a/0x3a
[ 1695.703390] ? i915_fence_get_timeline_name+0x53/0x90 [i915]
[ 1695.703836] i915_fence_get_timeline_name+0x53/0x90 [i915]
[ 1695.704241] print_request+0x82/0x2e0 [i915]
[ 1695.704638] ? fwtable_read32+0x133/0x360 [i915]
[ 1695.705042] ? write_timestamp+0x110/0x110 [i915]
[ 1695.705133] ? _raw_spin_lock_irqsave+0x79/0xc0
[ 1695.705221] ? refcount_inc_not_zero_checked+0x91/0x110
[ 1695.705306] ? refcount_dec_and_mutex_lock+0x50/0x50
[ 1695.705709] ? intel_engine_find_active_request+0x202/0x230 [i915]
[ 1695.706115] intel_engine_dump+0x2c9/0x900 [i915]
Fixes: c36eebd9ba ("drm/i915/gt: execlists->active is serialised by the tasklet")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191111114323.5833-1-chris@chris-wilson.co.uk
(cherry picked from commit fecffa4668)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
This fixes two different classes of bugs in the Intel graphics hardware:
MMIO register read hang:
"On Intels Gen8 and Gen9 Graphics hardware, a read of specific graphics
MMIO registers when the product is in certain low power states causes
a system hang.
There are two potential triggers for DoS:
a) H/W corruption of the RC6 save/restore vector
b) Hard hang within the MIPI hardware
This prevents the DoS in two areas of the hardware:
1) Detect corruption of RC6 address on exit from low-power state,
and if we find it corrupted, disable RC6 and RPM
2) Permanently lower the MIPI MMIO timeout"
Blitter command streamer unrestricted memory accesses:
"On Intels Gen9 Graphics hardware the Blitter Command Streamer (BCS)
allows writing to Memory Mapped Input Output (MMIO) that should be
blocked. With modifications of page tables, this can lead to privilege
escalation. This exposure is limited to the Guest Physical Address
space and does not allow for access outside of the graphics virtual
machine.
This series establishes a software parser into the Blitter command
stream to scan for, and prevent, reads or writes to MMIO's that should
not be accessible to non-privileged contexts.
Much of the command parser infrastructure has existed for some time,
and is used on Ivybridge/Haswell/Valleyview derived products to allow
the use of features normally blocked by hardware. In this legacy
context, the command parser is employed to allow normally unprivileged
submissions to be run with elevated privileges in order to grant
access to a limited set of extra capabilities. In this mode the parser
is optional; In the event that the parser finds any construct that it
cannot properly validate (e.g. nested command buffers), it simply
aborts the scan and submits the buffer in non-privileged mode.
For Gen9 Graphics, this series makes the parser mandatory for all
Blitter submissions. The incoming user buffer is first copied to a
kernel owned buffer, and parsed. If all checks are successful the
kernel owned buffer is mapped READ-ONLY and submitted on behalf of the
user. If any checks fail, or the parser is unable to complete the scan
(nested buffers), it is forcibly rejected. The successfully scanned
buffer is executed with NORMAL user privileges (key difference from
legacy usage).
Modern usermode does not use the Blitter on later hardware, having
switched over to using the 3D engine instead for performance reasons.
There are however some legacy usermode apps that rely on Blitter,
notably the SNA X-Server. There are no known usermode applications
that require nested command buffers on the Blitter, so the forcible
rejection of such buffers in this patch series is considered an
acceptable limitation"
* Intel graphics fixes in emailed bundle from Jon Bloomfield <jon.bloomfield@intel.com>:
drm/i915/cmdparser: Fix jump whitelist clearing
drm/i915/gen8+: Add RC6 CTX corruption WA
drm/i915: Lower RM timeout to avoid DSI hard hangs
drm/i915/cmdparser: Ignore Length operands during command matching
drm/i915/cmdparser: Add support for backward jumps
drm/i915/cmdparser: Use explicit goto for error paths
drm/i915: Add gen9 BCS cmdparsing
drm/i915: Allow parsing of unsized batches
drm/i915: Support ro ppgtt mapped cmdparser shadow buffers
drm/i915: Add support for mandatory cmdparsing
drm/i915: Remove Master tables from cmdparser
drm/i915: Disable Secure Batches for gen6+
drm/i915: Rename gen7 cmdparser tables
[Why]
On Navi10, and presumably arcterus, updating pp_table via sysfs would
not re-scale the maximum possible power limit one can set. On navi10,
the SMU code ignored the power percentage overdrive setting entirely,
and would not allow you to exceed the default power limit at all.
[How]
Adding a function to the SMU interface to get the pptable version of the
default power limit allows ASIC-specific code to provide the correct
maximum-settable power limit for the current pptable.
v3: fix spelling (Alex)
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Matt Coffin <mcoffin13@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Before this patch, navi10 overdrive settings could not be printed via
pp_od_clk_voltage
[How]
Implement printing for the overdrive settings for the following clocks
in navi10's ppt print_clk_levels implementation:
* SMU_OD_SCLK
* SMU_OD_MCLK
* SMU_OD_VDDC_CURVE
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Matt Coffin <mcoffin13@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Before this patch, there was no way to set the gfxclk voltage curve in
the overdrive settings for navi10 through pp_od_clk_voltage
[How]
Add the required implementation to navi10's ppt dpm table editing
implementation, similar to the vega20 implementation and interface.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Matt Coffin <mcoffin13@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Before this patch, there was no way to use pp_od_clk_voltage on navi
[How]
Similar to the vega20 implementation, but using the common smc_v11_0
headers, implemented the pp_od_clk_voltage API for navi10's pptable
implementation
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Matt Coffin <mcoffin13@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This fixes the formatting on one comment and consolidates the
pci_get_drvdata() into the radeon_suspend_kms().
Signed-off-by: Kyle Mahlkuch <kmahlkuc@linux.vnet.ibm.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
xgmi, ras, hdcp and dtm ta are actually separated ucode and
need to handled case by case to upload to psp.
We support the case that ta binary have one or multiple of
them built-in. As a result, the driver should check each ta
binariy's availablity before decide to upload them to psp.
In the terminate (unload) case, the driver will check the
context readiness before perform unload activity. It's fine
to keep it as is.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Le Ma <Le.Ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The gem_ctx_persistence/smoketest was detecting an odd coherency issue
inside the LRC context image; that the address of the ring buffer did
not match our associated struct intel_ring. As we set the address into
the context image when we pin the ring buffer into place before the
context is active, that leaves the question of where did it get
overwritten. Either the HW context save occurred after our pin which
would imply that our idle barriers are broken, or we overwrote the
context image ourselves. It is only in reset_active() where we dabble
inside the context image outside of a serialised path from schedule-out;
but we could equally perform the operation inside schedule-in which is
then fully serialised with the context pin -- and remains serialised by
the engine pulse with kill_context(). (The only downside, aside from
doing more work inside the engine->active.lock, was the plan to merge
all the reset paths into doing their context scrubbing on schedule-out
needs more thought.)
Fixes: d12acee84f ("drm/i915/execlists: Cancel banned contexts on schedule-out")
Testcase: igt/gem_ctx_persistence/smoketest
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191111133205.11590-3-chris@chris-wilson.co.uk
When a jump_whitelist bitmap is reused, it needs to be cleared.
Currently this is done with memset() and the size calculation assumes
bitmaps are made of 32-bit words, not longs. So on 64-bit
architectures, only the first half of the bitmap is cleared.
If some whitelist bits are carried over between successive batches
submitted on the same context, this will presumably allow embedding
the rogue instructions that we're trying to reject.
Use bitmap_zero() instead, which gets the calculation right.
Fixes: f8c08d8fae ("drm/i915/cmdparser: Add support for backward jumps")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jon Bloomfield <jon.bloomfield@intel.com>
set_page_dirty says:
For pages with a mapping this should be done under the page lock
for the benefit of asynchronous memory errors who prefer a
consistent dirty state. This rule can be broken in some special
cases, but should be better not to.
Under those rules, it is only safe for us to use the plain set_page_dirty
calls for shmemfs/anonymous memory. Userptr may be used with real
mappings and so needs to use the locked version (set_page_dirty_lock).
However, following a try_to_unmap() we may want to remove the userptr and
so call put_pages(). However, try_to_unmap() acquires the page lock and
so we must avoid recursively locking the pages ourselves -- which means
that we cannot safely acquire the lock around set_page_dirty(). Since we
can't be sure of the lock, we have to risk skip dirtying the page, or
else risk calling set_page_dirty() without a lock and so risk fs
corruption.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=203317
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=112012
Fixes: 5cc9ed4b9a ("drm/i915: Introduce mapping of user pages into video memory (userptr) ioctl")
References: cb6d7c7dc7 ("drm/i915/userptr: Acquire the page lock around set_page_dirty()")
References: 505a8ec7e1 ("Revert "drm/i915/userptr: Acquire the page lock around set_page_dirty()"")
References: 6dcc693bc5 ("ext4: warn when page is dirtied without buffers")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191111133205.11590-1-chris@chris-wilson.co.uk
