This patch set the correct value for oversampling maxItems. In the
original example, appears 3 items for oversampling while the maxItems
is set to 1, this patch fixes those issues.
Fixes: 416f882c3b ("dt-bindings: iio: adc: Migrate AD7606 documentation to yaml")
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Rob Herring <robh@kernel.org>
As the at25 uses the NVMEM subsystem, and the property is now being
handled, adding reference for it in the device tree binding document,
which allows to specify the GPIO line to which the write-protect pin
is connected.
Signed-off-by: Khouloud Touil <ktouil@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This reverts commit f5fa59a61e "regulator: bindings: add
document bindings for mpq7920" as Rob has a number of problems
with the use of DT schema.
Signed-off-by: Mark Brown <broonie@kernel.org>
The Allwinner A80 SoCs have a USB PHY controller that is used by Linux,
with a matching Device Tree binding.
Now that we have the DT validation in place, let's convert the device tree
bindings for that controller over to a YAML schemas.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This is an optional GPIO, if specified will be used to
swap lane 0 and lane 1 based on GPIO status. This is required
to achieve plug flip support for USB Type-C.
Type-C companions typically need some time after the cable is
plugged before and before they reflect the correct status of
Type-C plug orientation on the DIR line.
Type-C Spec specifies CC attachment debounce time (tCCDebounce)
of 100 ms (min) to 200 ms (max).
Allow the DT node to specify the time (in ms) that we need
to wait before sampling the DIR line.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Cc: Rob Herring <robh@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a YAML schema to use the host controller driver with the
eMMC PHY on Intel's Lightning Mountain SoC.
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add DT binding documentation for WIZ (SERDES wrapper). WIZ is *NOT* a
PHY but a wrapper used to configure some of the input signals to the
SERDES. It is used with both Sierra(16G) and Torrent(10G) serdes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[jsarha@ti.com: Add separate compatible for Sierra(16G) and Torrent(10G)
SERDES]
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
I need to create subnodes for drives connected to PATA
host controllers, and this needs to be supported generally,
so create a common YAML binding for "ide" that will support
subnodes with ports.
This has been designed as a subset of
ata/ahci-platform.txt with the bare essentials and
should be possible to extend or superset to cover the
common bindings.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
I need to create subnodes for drives connected to SATA
host controllers, and this needs to be supported
generally, so create a common YAML binding for
"sata" that will support subnodes with ports.
This has been designed as a subset of
ata/ahci-platform.txt with the bare essentials and
should be possible to extend or superset to cover the
common bindings.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[robh: fixup sata-port unit-address pattern]
Signed-off-by: Rob Herring <robh@kernel.org>
This fixes some problems that caused build errors in the
lgm-io schema file:
- No "bindings" infix in the schema id
- Move the allOf inclusion for pinconf and pinmux nodes into
the patternProperties for the -pins node
- We want "groups" not "group" to be compulsory for a pinmux
node blended with a pin config node.
- Fix the generic pinmux-schema to list "groups" rather than
"group" for a pinmux node, this might have led to some confusion.
This is a first user of the generic schema so a bit of a bumpy
road.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Rahul Tanwar <rahul.tanwar@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The firmware-name property in the zap node can be used to specify a
device specific zap firmware.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add the compatible enum entries for Gateworks Ventana boards.
Signed-off-by: Robert Jones <rjones@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull i2c fixes from Wolfram Sang:
"Two driver bugfixes, a documentation fix, and a removal of a spec
violation for the bus recovery algorithm in the core"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: fix bus recovery stop mode timing
i2c: bcm2835: Store pointer to bus clock
dt-bindings: i2c: at91: fix i2c-sda-hold-time-ns documentation for sam9x60
i2c: at91: fix clk_offset for sam9x60
Reset controller updates for v5.6
This tag adds support for the Nuvoton NPCM, Intel Gatway SoC, and
Broadcom BCM7216 RESCAL reset controllers, adds missing SCSSI reset
controls for newer Uniphier SoCs, aligns the program flow in the
devm_reset_controller_register, __devm_reset_control_get, and
devm_reset_control_array_get functions for better consistency,
and allows to build the Qcom AOSS reset driver as a module.
This is based on v5.5-rc3 because the core patch depends on commit
db23808615 ("reset: Do not register resource data for missing
resets").
* tag 'reset-for-5.6' of git://git.pengutronix.de/pza/linux:
reset: qcom-aoss: Allow CONFIG_RESET_QCOM_AOSS to be a tristate
reset: Add Broadcom STB RESCAL reset controller
dt-bindings: reset: Document BCM7216 RESCAL reset controller
reset: intel: Add system reset controller driver
dt-bindings: reset: Add YAML schemas for the Intel Reset controller
reset: uniphier: Add SCSSI reset control for each channel
reset: Align logic and flow in managed helpers
reset: npcm: add NPCM reset controller driver
dt-bindings: reset: Add binding constants for NPCM7xx reset controller
dt-bindings: reset: add NPCM reset controller documentation
Link: https://lore.kernel.org/r/dbbb2ca7490a0146d9ba632fd4d9f38063e03e9f.camel@pengutronix.de
Signed-off-by: Olof Johansson <olof@lixom.net>
New boards are the Radxa Rock Pi N10 using the VMARC SOM and Dalang
carrier board, separate versions for the two rockpro64 hardware revisions
which switched a pin between revisions. The rockpro64 also got
bluetooth support now.
The px30 got a lot of attention with dsi, gpu and thermal support.
Similarly the rk3399-roc-pc board also got attention with mtd flash,
sdr104 mode, hdmi sound, gpu and a lot of other smaller improvements.
Other than that there is a new gpu-cooling device for rk3399 a cpu
idle-state for rk3328 and more small improvements across a number
of boards.
* tag 'v5.6-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (37 commits)
arm64: dts: rockchip: Enable mp8859 regulator on rk3399-roc-pc
arm64: dts: rockchip: rk3399-hugsun-x99: remove supports-sd and supports-emmc options
arm64: dts: rockchip: rk3399-firefly: remove num-slots from &sdio0 node
arm64: dts: rockchip: Add PX30 LVDS
arm64: dts: rockchip: add dsi controller for px30
arm64: dts: rockchip: Add PX30 DSI DPHY
arm64: dts: rockchip: Add RK3328 idle state
arm64: dts: rockchip: remove identical &uart0 node from rk3368-lion-haikou
arm64: dts: rockchip: Add Radxa Rock Pi N10 initial support
ARM: dts: rockchip: Add Radxa Dalang Carrier board
arm64: dts: rockchip: Add VMARC RK3399Pro SOM initial support
dt-bindings: arm: rockchip: Add Rock Pi N10 binding
arm64: dts: rockchip: hook up bluetooth at uart0 on rockpro64
arm64: dts: rockchip: enable wifi module at sdio0 on rockpro64
arm64: dts: rockchip: split rk3399-rockpro64 for v2 and v2.1 boards
arm64: dts: rockchip: enable the gpu on px30-evb
arm64: dts: rockchip: add the gpu for px30
dt-bindings: gpu: mali-bifrost: Add Rockchip PX30
arm64: dts: rockchip: Add GPU cooling device for RK3399
arm64: dts: rockchip: Add regulators for PCIe for Radxa Rock Pi 4 board
...
Link: https://lore.kernel.org/r/5115625.yBEeHQkg2z@phil
Signed-off-by: Olof Johansson <olof@lixom.net>
Jonathan writes:
First set of new device support, features and cleanups for IIO in the 5.6 cycle
New device support
* ad7091r5 ADC
- New driver with follow up patch adding scale and vref support.
- DT bindings
* ad7923
- Support for ad7908, ad7918 and ad7928 added to driver.
* bma180
- Support the BMA254 accelerometer. Required fairly substantial rework
to allow for small differences between this an existing parts.
* bma400 accelerometer
- New driver with follow up patch for regulator support.
- DT bindings.
* asc dlhl60d
- New driver support this range of pressure and temperature sensors.
- DT bindings.
* ltc2496 ADC
- New driver to support this ADC.
- Split the existing LTC2497 driver generic component out and reuse.
- DT bindings.
* parallax ping
- New driver supporting ultrasonic and laser tof distance sensors.
- Bindings for these sensors.
New features
* core
- New char type for read_raw returns, used for thermocouple types.
- Rename read_first_n callback to read. The reasons behind the original
naming are lost to the mists of time.
* ad799x
- Allow pm_ops to disable device completely allowing regulator power down.
* bma180
- Enable basic regulator support.
* dmaengine buffer
- Report platform data alignment requirements via new ABI.
* max31856
- Add option to set mains filter rejection frequency and document
new in_temp_filter_notch_center_frequency ABI.
- Add support for configuring HW averaging (oversampling ratio)
- Add runtime configuration of thermocouple type and document new ABI.
* maxim-thermocouple
- Add read only access to thermocouple type using new ABI, includes
adding more specific compatibles to reflect which variant of the
chip is being used.
* mpu6050
- Provide option to support the PMU9150 in package magnetometer directly
rather than via auxiliary bus.
* stm32_adc
- Add overrun interrupt checks to detect if this happens.
* st_lsm6dsx
- Enable the sensor-hub support for lsm6dsm. Includes various reworks to
allow this.
Cleanups and minor fixes
* Subsystem wide
- Tidy up indentation in Kconfig and fix alphabetical order of AD7091R5.
- Drop linux/gpio.h and linux/of_gpio.h from drivers that don't use them.
* ad7266
- Convert to GPIO descriptors.
* ad7303
- Avoid a dance with checking if the regulator is supplied by just
using the optional request interface.
* ad7887
- Simplify channel specification assignment to enable adding more devices.
* ad7923
- Drop some unused and largely pointless defines of BOB_N==N variety.
- Tidy up checkpatch warnings.
- Add missing of_device_id table.
* adf4350
- Convert to GPIO descriptors.
* ak8975
- Convert to GPIO descriptors.
* ADIS library and drivers
- Expand scope of txrx_lock to cover all state and rename as state_lock
- Add unlocked read / write to allow grouping of consecutive calls under
single lock / unlock.
- Add unlocked check_status, reset to allow grouping under single
lock / unlock.
- Remove remaining uses of core mlock for local state protection.
mlock should never be used directly as it protects tightly defined
core IIO device management state.
* adis16240
- Enforce only supported SPI mode on driver load + add DT binding doc.
* atlas-ph-sensor
- Rename to atlas-sensor given it now covers things beyond ph sensors.
* bma180
- Use local dev variable to tidy up code.
- Use c99 style explicity .member assignment to make driver more readable.
* bmp280
- Drop ACPI support. No evidence this was used and appropriate ID is not
registered.
- Allow ACPI to bind device via PRP0001
* dmaengine buffer
- Use dma_request_chan instead of dma_request_slave_channel_reason as that
ABI is going away.
- Add module info to avoid tainting the kernel.
* hts221
- Avoid magic number defines when only used to fill structure elements
that are self describing.
* lm3533
- Drop a stray semicolon.
* max9611
- Cleanup enum handling to be more resilient to future changes.
* mpu6050
- Delete MPU9150 from supported SPI devices as doesn't provide SPI.
- Select I2C_MUX again after kbuild issue fixed elsewhere.
* stm32-timer
- Drop an unnecessary register update.
* ssp_sensors
- Convert to GPIO descriptors.
* st_sensors
- drop !CONFIG_ACPI defines as ACPI_PTR() will stop them being used
anyway.
- Make default platform data structures __maybe_unsued.
- Fill in some missing kernel-doc function parameters.
* st_lsm6dsx
- white space fixes.
- Mark some constants that aren't always used as __maybe_unused.
- Drop of ID table guards as they just pervent use under ACPI.
- Switch to device properties to allow ACPI usage.
* st_uvis25
- Drop acpi.h include as no ACPI APIs used.
* ti-ads1015
- Drop legacy platform data as no one seems to be using it.
- Use the device property API instead of OF specific.
* ti-ads7950
- typo fix in error message.
* tag 'iio-for-5.6a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (99 commits)
iio: accel: bma180: BMA254 support
iio: pressure: bmp280: Allow device to be enumerated from ACPI
iio: pressure: bmp280: Drop ACPI support
dt-bindings: iio: adc: convert sd modulator to json-schema
iio: buffer: rename 'read_first_n' callback to 'read'
iio: buffer-dmaengine: Report buffer length requirements
bindings: iio: pressure: Add documentation for dlh driver
dt-bindings: Add asc vendor
iio: pressure: Add driver for DLH pressure sensors
iio: buffer-dmaengine: Add module information
iio: accel: bma180: Use explicit member assignment
iio: accel: bma180: Basic regulator support
iio: accel: bma180: Add dev helper variable
iio: imu: st_lsm6dsx: enable sensor-hub support for lsm6dsm
iio: imu: st_lsm6dsx: rename st_lsm6dsx_shub_read_reg in st_lsm6dsx_shub_read_output
iio: imu: st_lsm6dsx: check if shub_output reg is located in primary page
iio: imu: st_lsm6dsx: check if pull_up is located in primary page
iio: imu: st_lsm6dsx: check if master_enable is located in primary page
iio: imu: st_lsm6dsx: export max num of slave devices in st_lsm6dsx_shub_settings
iio: light: remove unneeded semicolon
...
The ungrafting from PRIO bug fixes in net, when merged into net-next,
merge cleanly but create a build failure. The resolution used here is
from Petr Machata.
Signed-off-by: David S. Miller <davem@davemloft.net>
The Allwinner SoCs have a display engine composed of several controllers
assembled differently depending on the SoC, the number and type of output
they have, and the additional features they provide. A number of those are
supported in Linux, with the matching bindings.
Now that we have the DT validation in place, let's split into separate file
and convert the device tree bindings for those controllers to schemas.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20200103152801.47254-1-maxime@cerno.tech
