Valid values for InterruptThrottleRate are 10-100000, or one of
0, 1, 3, 4. '2' is not valid. This is a legacy from the branching
from the e1000 driver code that e1000e was based from.
Prior to this patch, if the e1000e driver was loaded with a forced
invalid InterruptThrottleRate of '2', then no throttle rate would be
set and no error message generated.
Now, a message will be generated that an invalid value was used and the
value for InterruptThrottleRate will be set to the default value.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ULP is a power saving feature that reduces the power consumption of the
PHY when a cable is not connected.
ULP is gated on the following conditions:
1) The hardware must support ULP. Currently this is only I218
devices from Intel
2) ULP is initiated by the driver, so, no driver results in no ULP.
3) ULP's implementation utilizes Runtime Power Management to toggle its
execution. ULP is enabled/disabled based on the state of Runtime PM.
4) ULP is not active when wake-on-unicast, multicast or broadcast is active
as these features are mutually-exclusive.
Since the PHY is in an unavailable state while ULP is active, any access
of the PHY registers will fail. This is resolved by utilizing kernel
calls that cause the device to exit Runtime PM (e.g. pm_runtime_get_sync)
and then, after PHY access is complete, allow the device to resume
Runtime PM (e.g. pm_runtime_put_sync).
Under certain conditions, toggling the LANPHYPC is necessary to disable
ULP mode. Break out existing code to toggle LANPHYPC to a new function
to avoid code duplication.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix issues with:
RuntimePM causing the device to repeatedly flip between suspend and resume
with the interface administratively downed.
Having RuntimePM enabled interfering with the functionality of Energy
Efficient Ethernet.
Added checks to disallow functions that should not be executed if the
device is currently runtime suspended
Make runtime_idle callback to use same deterministic behavior as the igb
driver.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Refactor the system power management flows to prevent the suspend path from
being executed twice when hibernating since both the freeze and
poweroff callbacks were set to e1000_suspend() via SET_SYSTEM_SLEEP_PM_OPS.
There are HW workarounds that are performed during this flow and calling
them twice was causing erroneous behavior.
Re-arrange the code to take advantage of common code paths and explicitly
set the individual dev_pm_ops callbacks for suspend, resume, freeze,
thaw, poweroff and restore.
Add a boolean parameter (reset) to the e1000e_down function to allow
for cases when the HW should not be reset when downed during a PM event.
Now that all suspend/shutdown paths result in a call to __e1000_shutdown()
that checks Wake on Lan status, removing redundant check for WoL in
e1000_power_down_phy().
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is to update the GPL header by removing the portion that
refers to the Free Software Foundation address.
Change the copyright date for 2014.
Reformat the header comments to conform to kernel networking coding norms
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enabling EEE LPI sooner than one second after link up on 82579 causes link
issues with some switches.
Remove EEE enablement for 82579 parts from the link initialization flow to
avoid initializing too early. EEE initialization for 82579 will be done
in e1000e_update_phy_task.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce W Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On a ME enabled system with the cable out, the driver init flow would
generate an erroneous message indicating that resets were being blocked
by an active ME session. Cause was ME clearing the semaphore bit to
block further PHY resets for up to 50 msec during power-on/cycle. After
this interval, ME would re-set the bit and allow PHY resets.
To resolve this, change the flow of e1000e_phy_hw_reset_generic() to
utilize a delay and retry method. Poll the FWSM register to minimize
any extra time added to the flow. If the delay times out at 100ms
(checked in 10msec increments), then return the value E1000_BLK_PHY_RESET,
as this is the accurate state of the PHY. Attempting to alter just the
call to e1000e_phy_hw_reset_generic() in e1000_init_phy_workarounds_pchlan()
just caused the problem to move further down the flow.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce W. Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Marc Kleine-Budde says:
====================
pull-request: can-next 2014-02-12
this is a pull request of twelve patches for net-next/master.
Alexander Shiyan contributes two patches for the mcp251x, one making
the driver more quiet and the other one improves the compile time
coverage by removing the #ifdef CONFIG_PM_SLEEP. Then two patches for
the flexcan driver by me, one removing the #ifdef CONFIG_PM_SLEEP, too,
the other one making use of platform_get_device_id(). Another patch by
me which converts the janz-ican3 driver to use netdev_<level>(). The
remaining 7 patches are by Oliver Hartkopp, they add CAN FD support to
the netlink configuration interface.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Support hw IPv6 checksum for TCP and UDP packets.
Note that the hw has the limitation of the range of the transport
offset. Besides, the TCP Pseudo Header of the IPv6 TSO of the hw
bases on the Microsoft document which excludes the packet length.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support scatter gather and TSO.
Adjust the tx checksum function and set the max gso size to fix the
size of the tx aggregation buffer.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Continue dealing with the remain rx packets, even though the allocation
of the skb fail. This could calculate the correct dropped packets.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
move the tx_bottom() from delayed_work to tasklet. It makes the rx
and tx balanced. If the device is in runtime suspend when getting
the tx packet, wakeup the device before trasmitting.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check tx agg list before spin lock to avoid doing spin lock every
times.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use spin_lock and spin_unlock in interrupt context.
The ndo_start_xmit would not be called in interrupt context, so
replace the relative spin_lock_irqsave and spin_unlock_irqrestore
with spin_lock_bh and spin_unlock_bh.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to i40e and i40evf.
Most notable are:
Joseph completes the implementation of the ethtool ntuple rule
management interface by adding the get, update and delete interface
reset.
Akeem provides a fix to prevent a possible overflow due to multiplication
of number and size by using kzalloc, so use kcalloc.
Jesse provides an implementation for skb_set_hash() and adds the L4 type
return when we know it is an L4 hash. He also adds a counter to
statistics for Tx timeouts to help users. Lastly he provides a change
to stay away from the cache line where the done bit may be getting
written back for the transmit ring since the hardware may be writing the
whole cache line for a partial update.
Shannon cleans up code comments.
Anjali removes a firmware workaround for newer firmware since the number
of MSIx vectors are being reported correctly.
v2:
- dropped patch 01 of the series based on feedback from the author
Joe Perches and Shannon Nelson.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Unmapping causes TLB flushing, therefore we should make it in the largest
possible batches. However we shouldn't starve the guest for too long. So if
the guest has space for at least two big packets and we don't have at least a
quarter ring to unmap, delay it for at most 1 milisec.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A malicious or buggy guest can leave its queue filled indefinitely, in which
case qdisc start to queue packets for that VIF. If those packets came from an
another guest, it can block its slots and prevent shutdown. To avoid that, we
make sure the queue is drained in every 10 seconds.
The QDisc queue in worst case takes 3 round to flush usually.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xen network protocol had implicit dependency on MAX_SKB_FRAGS. Netback has to
handle guests sending up to XEN_NETBK_LEGACY_SLOTS_MAX slots. To achieve that:
- create a new skb
- map the leftover slots to its frags (no linear buffer here!)
- chain it to the previous through skb_shinfo(skb)->frag_list
- map them
- copy and coalesce the frags into a brand new one and send it to the stack
- unmap the 2 old skb's pages
It's also introduces new stat counters, which help determine how often the guest
sends a packet with more than MAX_SKB_FRAGS frags.
NOTE: if bisect brought you here, you should apply the series up until
"xen-netback: Timeout packets in RX path", otherwise malicious guests can block
other guests by not releasing their sent packets.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These counters help determine how often the buffers had to be copied. Also
they help find out if packets are leaked, as if "sent != success + fail",
there are probably packets never freed up properly.
NOTE: if bisect brought you here, you should apply the series up until
"xen-netback: Timeout packets in RX path", otherwise Windows guests can't work
properly and malicious guests can block other guests by not releasing their sent
packets.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These became obsolete with grant mapping. I've left intentionally the
indentations in this way, to improve readability of previous patches.
NOTE: if bisect brought you here, you should apply the series up until
"xen-netback: Timeout packets in RX path", otherwise Windows guests can't work
properly and malicious guests can block other guests by not releasing their sent
packets.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces grant mapping on netback TX path. It replaces grant copy
operations, ditching grant copy coalescing along the way. Another solution for
copy coalescing is introduced in "xen-netback: Handle guests with too many
frags", older guests and Windows can broke before that patch applies.
There is a callback (xenvif_zerocopy_callback) from core stack to release the
slots back to the guests when kfree_skb or skb_orphan_frags called. It feeds a
separate dealloc thread, as scheduling NAPI instance from there is inefficient,
therefore we can't do dealloc from the instance.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX path need to know if the SKB fragments are stored on pages from another
domain.
Logically this patch should be after introducing the grant mapping itself, as
it makes sense only after that. But to keep bisectability, I moved it here. It
shouldn't change any functionality here. xenvif_zerocopy_callback and
ubuf_to_vif are just stubs here, they will be introduced properly later on.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains a few bits of refactoring before introducing the grant
mapping changes:
- introducing xenvif_tx_pending_slots_available(), as this is used several
times, and will be used more often
- rename the thread to vifX.Y-guest-rx, to signify it does RX work from the
guest point of view
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Storing the pending_idx at the first byte of the linear buffer never looked
good, skb->cb is a more proper place for this. It also prevents the header to
be directly grant copied there, and we don't have the pending_idx after we
copied the header here, so it's time to change it.
It also introduces helpers for the RX side
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 3804fad454.
This commit, together with commit 247bf55727
"xhci 1.0: Limit arbitrarily-aligned scatter gather." were
origially added to get xHCI 1.0 hosts and usb ethernet ax88179_178a devices
working together with scatter gather. xHCI 1.0 hosts pose some requirement on how transfer
buffers are aligned, setting this requirement for 1.0 hosts caused USB 3.0 mass
storage devices to fail more frequently.
USB 3.0 mass storage devices used to work before 3.14-rc1. Theoretically,
the TD fragment rules could have caused an occasional disk glitch.
Now the devices *will* fail, instead of theoretically failing.
>From a user perspective, this looks like a regression; the USB device obviously
fails on 3.14-rc1, and may sometimes silently fail on prior kernels.
The proper soluition is to implement the TD fragment rules for xHCI 1.0 hosts,
but for now, revert this patch until scatter gather can be properly supported.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will be useful when processing signature errors on a specific
key. The mlx5 driver will lookup the matching mlx5 memory region
structure and mark it as dirty (contains signature errors).
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Support create_mr and destroy_mr verbs. Creating ib_mr may be done
for either ib_mr that will register regular page lists like
alloc_fast_reg_mr routine, or indirect ib_mrs that can register other
(pre-registered) ib_mrs in an indirect manner.
In addition user may request signature enable, that will mean that the
created ib_mr may be attached with signature attributes (BSF, PSVs).
Currently we only allow direct/indirect registration modes.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
PREPARE_[DELAYED_]WORK() are being phased out. They have few users
and a nasty surprise in terms of reentrancy guarantee as workqueue
considers work items to be different if they don't have the same work
function.
Update rt2800usb.c to use INIT_WORK() instead of PREPARE_WORK(). As
the work item isn't in active use during rt2800usb_probe_hw(), this
doesn't cause any behavior difference.
It would probably be best to route this with other related updates
through the workqueue tree.
Only compile tested.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: linux-wireless@vger.kernel.org
Additionally to have the second (data) bitrate available the data bitrate
has to be greater or equal to the arbitration bitrate in CAN FD.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The configuration for CAN FD depends on CAN_CTRLMODE_FD enabled in the driver
specific ctrlmode_supported capabilities.
The configuration can be done either with the 'fd { on | off }' option in the
'ip' tool from iproute2 or by setting the CAN netdevice MTU to CAN_MTU (16) or
to CANFD_MTU (72).
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
As CAN FD offers a second bitrate for the data section of the CAN frame the
infrastructure for storing and configuring this second bitrate is introduced.
Improved the readability of the if-statement by inserting some newlines.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
As the bittiming calculation functions are to be used with different
bittiming_const structures for CAN and CAN FD the direct reference to
priv->bittiming_const inside these functions has to be removed.
Also moved the check for existing bittiming const to one place.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch moves a sanity check in order to have a second user for CAN FD.
Also simplify the return value generation in can_get_bittiming() as only
correct return values of can_[calc|fixup]_bittiming() lead to a return value of
zero.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When setting the bitrate both can_calc_bittiming() and can_fixup_bittiming()
lead to the bitrate variable to be set, when a proper bit timing is available.
Only then the bitrate configuration is stored for the device, so checking for
priv->bittiming.bitrate is always sufficient.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The skbuff protocol value was formerly fixed/sanitized to ETH_P_CAN in
can_put_echo_skb(). With CAN FD this value has to be preserved.
This patch changes the hard assignment of the protocol value to a check of
valid protocol values for CAN and CAN FD.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch converts the dev_<level> printing to netdev_<level>, this makes it
possible to remove the "struct device *dev" pointer from the "struct
ican3_dev".
Cc: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Seems like we have an old bug, where we incidently overwrites
the max_antenna_gain we pass to firmware, with zero value.
End of all we are artifically reducing the output power.
This patch removes the excessive assignment on max_antenna_gain,
which is being provided by regulatory domain, and consequently
improves the tx power.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Consolidate the list of msdu skbs into the msdu-head skb, delete the
rest of the skbs, pass the msdu-head skb on up the stack as normal.
Tested with high-speed TCP and UDP traffic on modified firmware that
supports raw-rx.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
We need to make sure that we stay away from the cache line
where the DD bit (done) may be getting written back for
the transmit ring since the hardware may be writing the
whole cache line for a partial update.
Change-ID: Id0b6dfc01f654def6a2a021af185803be1915d7e
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver needs to use the format that the current NVM
uses when printing the version of the NVM. It should remain
this way from now on forward.
The driver was reporting when firmware was less than
an expected version number, but this is not a requirement
for the product and we print the firmware number at
init and in ethtool -i output. Just remove the print.
Change-ID: Ide0b856cd454ebf867610ef9a0d639bb358a4a60
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
