Exynos5250 and Exynos542x SoCs have the same CEC hardware module as
Exynos4 SoC series, so enable support for it using the same compatible
string.
Tested on Odroid XU3 (Exynos5422) and Google Snow (Exynos5250) boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The BAD_MADT_GICC_ENTRY() macro checks if a GICC MADT entry passes
muster from an ACPI specification standpoint. Current macro detects the
MADT GICC entry length through ACPI firmware version (it changed from 76
to 80 bytes in the transition from ACPI 5.1 to ACPI 6.0 specification)
but always uses (erroneously) the ACPICA (latest) struct (ie struct
acpi_madt_generic_interrupt - that is 80-bytes long) length to check if
the current GICC entry memory record exceeds the MADT table end in
memory as defined by the MADT table header itself, which may result in
false negatives depending on the ACPI firmware version and how the MADT
entries are laid out in memory (ie on ACPI 5.1 firmware MADT GICC
entries are 76 bytes long, so by adding 80 to a GICC entry start address
in memory the resulting address may well be past the actual MADT end,
triggering a false negative).
Fix the BAD_MADT_GICC_ENTRY() macro by reshuffling the condition checks
and update them to always use the firmware version specific MADT GICC
entry length in order to carry out boundary checks.
Fixes: b6cfb27737 ("ACPI / ARM64: add BAD_MADT_GICC_ENTRY() macro")
Reported-by: Julien Grall <julien.grall@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Julien Grall <julien.grall@arm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Al Stone <ahs3@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Rockchip's rk3229 evaluation board has one usb otg controller
and three usb host controllers. Each usb controller connect
with one usb2 phy port through UTMI+ interface. And the three
usb host interfaces use the same GPIO VBUS drive. Let's enable
them to support usb on rk3229 evb board.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds usb otg/host controllers and phys nodes on rk322x.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The xor_vmx.c file is used for the RAID5 xor operations. In these functions
altivec is enabled to run the operation and then disabled.
The code uses enable_kernel_altivec() around the core of the algorithm, however
the whole file is built with -maltivec, so the compiler is within its rights to
generate altivec code anywhere. This has been seen at least once in the wild:
0:mon> di $xor_altivec_2
c0000000000b97d0 3c4c01d9 addis r2,r12,473
c0000000000b97d4 3842db30 addi r2,r2,-9424
c0000000000b97d8 7c0802a6 mflr r0
c0000000000b97dc f8010010 std r0,16(r1)
c0000000000b97e0 60000000 nop
c0000000000b97e4 7c0802a6 mflr r0
c0000000000b97e8 faa1ffa8 std r21,-88(r1)
...
c0000000000b981c f821ff41 stdu r1,-192(r1)
c0000000000b9820 7f8101ce stvx v28,r1,r0 <-- POP
c0000000000b9824 38000030 li r0,48
c0000000000b9828 7fa101ce stvx v29,r1,r0
...
c0000000000b984c 4bf6a06d bl c0000000000238b8 # enable_kernel_altivec
This patch splits the non-altivec code into xor_vmx_glue.c which calls the
altivec functions in xor_vmx.c. By compiling xor_vmx_glue.c without
-maltivec we can guarantee that altivec instruction will not be executed
outside of the enable/disable block.
Signed-off-by: Matt Brown <matthew.brown.dev@gmail.com>
[mpe: Rework change log and include disassembly]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
By default, 5% of system RAM is reserved for preserving boot memory.
Alternatively, a user can specify the amount of memory to reserve.
See Documentation/powerpc/firmware-assisted-dump.txt for details. In
addition to the memory reserved for preserving boot memory, some more
memory is reserved, to save HPTE region, CPU state data and ELF core
headers.
Memory Reservation during first kernel looks like below:
Low memory Top of memory
0 boot memory size |
| | |<--Reserved dump area -->|
V V | Permanent Reservation V
+-----------+----------/ /----------+---+----+-----------+----+
| | |CPU|HPTE| DUMP |ELF |
+-----------+----------/ /----------+---+----+-----------+----+
| ^
| |
\ /
-------------------------------------------
Boot memory content gets transferred to
reserved area by firmware at the time of
crash
This implicitly means that the sum of the sizes of boot memory, CPU
state data, HPTE region, DUMP preserving area and ELF core headers
can't be greater than the total memory size. But currently, a user is
allowed to specify any value as boot memory size. So, the above rule
is violated when a boot memory size around 50% of the total available
memory is specified. As the kernel is not handling this currently, it
may lead to undefined behavior. Fix it by setting an upper limit for
boot memory size to 25% of the total available memory. Also, instead
of using memblock_end_of_DRAM(), which doesn't take the holes, if any,
in the memory layout into account, use memblock_phys_mem_size() to
calculate the percentage of total available memory.
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With commit f6e6bedb77 ("powerpc/fadump: Reserve memory at an offset
closer to bottom of RAM"), memory for fadump is no longer reserved at
the top of RAM. But there are still a few places which say so. Change
them appropriately.
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With commit 11550dc0a0 ("powerpc/fadump: reuse crashkernel parameter
for fadump memory reservation"), 'fadump_reserve_mem=' parameter is
deprecated in favor of 'crashkernel=' parameter. Add a warning if
'fadump_reserve_mem=' is still used.
Fixes: 11550dc0a0 ("powerpc/fadump: reuse crashkernel parameter for fadump memory reservation")
Suggested-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
[mpe: Unsplit long printk strings]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- log an error message when registration fails and no error code listed
in the switch is returned
- translate the hv error code to posix error code and return it from
fw_register
- return the posix error code from fw_register to the process writing
to sysfs
- return EEXIST on re-registration
- return success on deregistration when fadump is not registered
- return ENODEV when no memory is reserved for fadump
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Tested-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
[mpe: Use pr_err() to shrink the error print]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With the ffz() function as defined in arch/powerpc/include/asm/bitops.h
GCC will not optimise the code in case of constant parameter.
This patch replaces ffz() by the generic function.
The generic ffz(x) expects to never be called with ~x == 0
as written in the comment in include/asm-generic/bitops/ffz.h
The only user of ffz() within arch/powerpc/ is
platforms/512x/mpc5121_ads_cpld.c, which checks if x is not 0xff
For non constant calls, the generated code is doing the same:
unsigned long testffz(unsigned long x)
{
return ffz(x);
}
On PPC32, before the patch:
00000018 <testffz>:
18: 7c 63 18 f9 not. r3,r3
1c: 40 82 00 0c bne 28 <testffz+0x10>
20: 38 60 00 20 li r3,32
24: 4e 80 00 20 blr
28: 7d 23 00 d0 neg r9,r3
2c: 7d 23 18 38 and r3,r9,r3
30: 7c 63 00 34 cntlzw r3,r3
34: 20 63 00 1f subfic r3,r3,31
38: 4e 80 00 20 blr
On PPC32, after the patch:
00000018 <testffz>:
18: 39 23 00 01 addi r9,r3,1
1c: 7d 23 18 78 andc r3,r9,r3
20: 7c 63 00 34 cntlzw r3,r3
24: 20 63 00 1f subfic r3,r3,31
28: 4e 80 00 20 blr
On PPC64, before the patch:
0000000000000030 <.testffz>:
30: 7c 60 18 f9 not. r0,r3
34: 38 60 00 40 li r3,64
38: 4d 82 00 20 beqlr
3c: 7c 60 00 d0 neg r3,r0
40: 7c 63 00 38 and r3,r3,r0
44: 7c 63 00 74 cntlzd r3,r3
48: 20 63 00 3f subfic r3,r3,63
4c: 7c 63 07 b4 extsw r3,r3
50: 4e 80 00 20 blr
On PPC64, after the patch:
0000000000000030 <.testffz>:
30: 38 03 00 01 addi r0,r3,1
34: 7c 03 18 78 andc r3,r0,r3
38: 7c 63 00 74 cntlzd r3,r3
3c: 20 63 00 3f subfic r3,r3,63
40: 4e 80 00 20 blr
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It often happens to have simultaneous interrupts, for instance
when having double Ethernet attachment. With the current
implementation, we suffer the cost of kernel entry/exit for each
interrupt.
This patch introduces a loop in __do_irq() to handle all interrupts
at once before returning.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
IRQ 0 is a valid HW interrupt. So get_irq() shall return 0 when
there is no irq, instead of returning irq_linear_revmap(... ,0)
Fixes: f2a0bd3753 ("[POWERPC] 8xx: powerpc port of core CPM PIC")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The 8xx has a dedicated exception for breakpoints, that directly
calls do_break()
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Function store_updates_sp() checks whether the faulting
instruction is a store updating r1. Therefore we can limit its calls
to store exceptions.
This patch is an improvement of commit a7a9dcd882 ("powerpc: Avoid
taking a data miss on every userspace instruction miss")
With the same microbenchmark app, run with 500 as argument, on an
MPC885 we get:
Before this patch: 152000 DTLB misses
After this patch: 147000 DTLB misses
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The check in hpte_find() should be < and not <= for PAGE_OFFSET
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Realtek ARM64 based SoC DT for v4.12
This adds an initial DT for the RTD1295 SoC and a TV box based on it.
* tag 'realtek-arm64-dt-for-4.12' of git://github.com/afaerber/linux:
ARM64: dts: Add Realtek RTD1295 and Zidoo X9S
dt-bindings: arm: Add Realtek RTD1295 bindings
dt-bindings: Add vendor prefix for Zidoo
Signed-off-by: Olof Johansson <olof@lixom.net>
Realtek ARM64 SoC for v4.12
This adds a Kconfig symbol for DTs being added, plus a MAINTAINERS entry.
* tag 'realtek-arm64-soc-for-4.12' of git://github.com/afaerber/linux:
MAINTAINERS: Add Realtek section
ARM64: Prepare Realtek RTD1295
Signed-off-by: Olof Johansson <olof@lixom.net>
This augments the Moxa Art and Aspeed device trees to:
- Explicitly name the clock "PCLK" as the Faraday FTTMR010
names it.
- List the Moxa timer as compatible with the Faradat FTTMR010
vanilla version.
- Add a comment that the Aspeed driver is a Faraday
FTTMR010 derivative.
- Pass all IRQs to the timer from Aspeed: they are all there
so they should be in the device tree, we only use the
first one anyways.
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This is a first set of Gemini DTS patches for the v4.13 cycle.
This adds the reset and clock lines to the Gemini core DTS SoC.
These bindings have been ACKed by the DT maintainer Rob.
The reset driver is going to be merged by the reset maintainer.
The clock driver is going to be merged by the clock maintainers.
Each of these have their macro defines coming with them, split
off as separate patches.
A post-rc1 patch will be sumbitted for switching the numerical
values to the defined macros in line with the ARM SoC DT header
merge strategy.
* tag 'gemini-v4.13-dts-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: Add clocks to the Gemini SoC
ARM: dts: Add the Gemini reset controller
dt-bindings: Augment Gemini for clocks, resets
Signed-off-by: Olof Johansson <olof@lixom.net>
Renesas ARM64 Based SoC DT Updates for v4.13
* Add support for R-Car H3 ES2.0
* Break out common board support
* Set drive-strength for ravb pins for r8a7795/h3ulcb and r8a7796/m3ulcb
* Enable HDMI outputs on r8a7795/salvator-x
* Add R-Car audio to DT of r8a7796 SoC
* Add current sense amplifiers to DT of r8a779[56]/salvator-x
* Enable NFS-root on r8a7796/salvator-x
* Enable HS200 for eMMC on r8a779[56]/salvator-x,
r8a7795/h3ulcb and r8a7796/m3ulcb
* Enable EthernetAVB, I2C r8a7796/m3ulcb
* Update memory node to 2 GiB map on r8a7796/m3ulcb
* tag 'renesas-arm64-dt-for-v4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (35 commits)
arm64: dts: r8a7795: salvator-x: Add support for R-Car H3 ES2.0
arm64: dts: r8a7795: Add support for R-Car H3 ES2.0
arm64: dts: ulcb: Set drive-strength for ravb pins
arm64: dts: renesas: r8a7795-salvator-x: Enable HDMI outputs
arm64: dts: renesas: r8a7795-salvator-x: Add DU external dot clocks
arm64: dts: renesas: salvator-x: Add HDMI output connectors
arm64: dts: renesas: salvator-x: Add DU external dot clock sources
arm64: dts: renesas: r8a7795: Add HDMI encoder support
arm64: dts: salvator-x: Add panel backlight support
arm64: dts: r8a7796: Add PWM device nodes
arm64: dts: r8a7796: add Sound MIX support
arm64: dts: r8a7796: add Sound CTU support
arm64: dts: r8a7796: add Sound DVC support
arm64: dts: r8a7796: add Sound SRC support
arm64: dts: r8a7796: add Sound SSI DMA support
arm64: dts: r8a7796: add Sound SSI PIO support
arm64: dts: r8a7796: add AUDIO_DMAC support
arm64: dts: salvator-x: Add current sense amplifiers
arm64: dts: renesas: Extract common ULCB board support
arm64: dts: renesas: Extract common Salvator-X board support
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Renesas ARM Based SoC DT Updates for v4.13
* Switch to panel-lvds bindings for Mitsubishi panels
* Clean up PFC node names
* Enable UHS-I SDR-50 and SDR-104 on r8a7793/Gose
* Add GyroADC clock and device for r8a7791 SoC
* Add USB clocks to device tree for r7s72100 SoC
* tag 'renesas-dt-for-v4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: dts: renesas: Switch to panel-lvds bindings for Mitsubishi panels
ARM: dts: gose: Enable UHS-I SDR-50 and SDR-104
ARM: dts: r8a7793: set maximum frequency for SDHI clocks
ARM: dts: r8a7791: Add GyroADC clock and device node
ARM: dts: r7s72100: add usb clocks to device tree
ARM: dts: sh73a0: update PFC node name to pin-controller
ARM: dts: r8a7793: update PFC node name to pin-controller
ARM: dts: r8a7791: update PFC node name to pin-controller
ARM: dts: r8a7790: update PFC node name to pin-controller
ARM: dts: r8a7779: update PFC node name to pin-controller
ARM: dts: r8a7778: update PFC node name to pin-controller
ARM: dts: r8a7740: update PFC node name to pin-controller
ARM: dts: r8a73a4: update PFC node name to pin-controller
ARM: dts: emev2: update PFC node name to pin-controller
ARM: dts: r7s72100: add USB bit definitions
ARM: dts: r7s72100: add Renesas RZ/A1 pinctrl header
ARM: dts: r8a7791: add GyroADC clock
Signed-off-by: Olof Johansson <olof@lixom.net>
ARCH_VULCAN (Broadcom Vulcan) has been discontinued and all its
dependencies have been moved to ARCH_THUNDER2. It can be dropped
from defconfig now.
Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Disable the option ARCH_VULCAN as a step towards deleting it entirely.
There is still a reference in the kernel tree for ARCH_VULCAN, so we
have to keep the config option around until that reference is removed.
Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
mvebu fixes for 4.12
Fix the interrupt description of the crypto node for device tree of
the Armada 7K/8K SoCs
* tag 'mvebu-fixes-4.12-1' of git://git.infradead.org/linux-mvebu: (316 commits)
arm64: marvell: dts: fix interrupts in 7k/8k crypto nodes
+ Linux 4.12-rc2
Signed-off-by: Olof Johansson <olof@lixom.net>
Fixes for 4.12:
Fix two compilation issues
* tag 'at91-4.12-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: at91: select CONFIG_ARM_CPU_SUSPEND
memory: atmel-ebi: mark PM ops as __maybe_unused
Signed-off-by: Olof Johansson <olof@lixom.net>
Most of DT files in ARM use #include "..." to make pre-processor
include DT in the same directory, but this is one of the exceptional
files that use #include <...> for that.
Fix it to remove -I$(srctree)/arch/$(SRCARCH)/boot/dts path from
dtc_cpp_flags.
ARM: dts: versatile: use #include "..." to include DT in the same directory
Most of DT files in ARM use #include "..." to make pre-processor
include DT in the same directory, but we have 3 exceptional files
that use #include <...> for that.
They must be fixed to remove -I$(srctree)/arch/$(SRCARCH)/boot/dts
path from dtc_cpp_flags.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The only adc button connected to adc input is recovery button.
Signed-off-by: Randy Li <ayaka@soulik.info>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Right now mach-imx6ul registers a fixup for the ksz8081 phy. The same
register values can be set through the micrel phy driver by using dts
properties.
This seems preferable and allows cleanly fixing suspend/resume.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable the dwmac-sun8i ethernet driver as a module in the ARM64 defconfig.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable the dwmac-sun8i driver in the multi_v7 default configuration
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dwmac-sun8i hardware is present on the BananaPi M64.
It uses an external PHY rtl8211e via RGMII.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dwmac-sun8i hardware is present on the pine64 plus.
It uses an external PHY rtl8211e via RGMII.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dwmac-sun8i hardware is present on the pine64
It uses an external PHY via RMII.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dwmac-sun8i is an Ethernet MAC that supports 10/100/1000 Mbit
connections. It is very similar to the device found in the Allwinner
H3, but lacks the internal 100 Mbit PHY and its associated control
bits.
This adds the necessary bits to the Allwinner A64 SoC .dtsi, but keeps
it disabled at this level.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the dt node for the syscon register present on the
Allwinner A64.
Only two register are present in this syscon and the only one useful is
the one dedicated to EMAC clock.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dwmac-sun8i hardware is present on the NanoPi Neo.
It uses the internal PHY.
This patch create the needed emac node.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the Orange Pi PC Plus, the polarity of the LEDs on the RJ45 Ethernet
port were changed from active low to active high.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dwmac-sun8i hardware is present on the Orange PI 2.
It uses the internal PHY.
This patch create the needed emac node.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dwmac-sun8i hardware is present on the Orange PI One.
It uses the internal PHY.
This patch create the needed emac node.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
