s/traing/training/
...Plus the entire sentence construction for better readability.
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GFX is in gfxoff mode during s0ix so we shouldn't need to
actually tear anything down and restore it.
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Not needed as the device is in gfxoff state so the CG/PG state
is handled just like it would be for gfxoff during runtime gfxoff.
This should also prevent delays on resume.
Reworked from Pratik's original patch (Alex)
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Pratik Vishwakarma <Pratik.Vishwakarma@amd.com>
Provide and explanation as to why we skip GFX and PSP for
S0ix. GFX goes into gfxoff, same as runtime, so no need
to tear down and re-init. PSP is part of the always on
state, so no need to touch it.
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The SMU expects CGPG to be enabled when entering S0ix.
with this we can re-enable SMU suspend.
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This really needs to be done to properly tear down
the device. SMC, PSP, and GFX are still problematic,
need to dig deeper into what aspect of them that is
problematic.
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move the non-DC specific code into the DCE IP blocks similar
to how we handle DC. This cleans up the common suspend
and resume pathes.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Vram is system memory, so no need to evict.
v2: use PM_EVENT messages
v3: use correct dev
v4: use driver flags
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Set flags at the top level pmops callbacks to track
state. This cleans up the current set of flags and
properly handles S4 on S0ix capable systems.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There's no need to keep vgaswitcheroo around for HG
systems. They don't use muxes and their power control
is handled via ACPI.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Once the device has runtime suspended, we don't need to power it
back up again for system suspend. Likewise for resume, we don't
to power up the device again on resume only to power it back off
again via runtime pm because it's still idle.
v2: add DPM_FLAG_SMART_PREPARE as well
Reviewed-by: Evan Quan <evan.quan@amd.com>
Acked-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com> (v1)
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
as per:
https://www.kernel.org/doc/html/latest/driver-api/pm/devices.html
The prepare callback is required to support the DPM_FLAG_SMART_SUSPEND
driver flag. This allows runtime pm to auto complete when the
system goes into suspend avoiding a wake up on suspend and on resume.
Apply this for hybrid gfx and BOCO systems where d3cold is
provided by the ACPI platform.
v2: check if device is runtime suspended in prepare.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
KIQ ring is being operated by kfd as well as amdgpu.
KFD is using kiq lock, we should the same from amdgpu side
as well.
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When recovery thread has begun GPU reset, there should be not other
threads to access hardware, otherwise system randomly hang.
v2 (chk): rewritten from scratch, use trylock and lockdep instead of
hand wiring the logic.
v3: add in_irq check
v4: change to check in_task
Signed-off-by: Dennis Li <Dennis.Li@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Display features should not be initialized or de-initialized when there
is no display. Skip modeset initialization, output setup, plane, crtc,
encoder, connector registration, display cdclk and rawclk
initialization, display core initialization, etc.
Skip the functionality at as high level as possible, and remove any
redundant checks. If the functionality is conditional to *other* display
checks, do not add more. If the un-initialization has checks for
initialization, do not add more.
We explicitly do not care about any GMCH/VLV/CHV code paths, as they've
always had and will have display.
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210408203150.237947-3-jose.souza@intel.com
Leaving this at a close-to-maximum register value 0xFFF0 means it takes
very long for the MDSS to generate a software vsync interrupt when the
hardware TE interrupt doesn't arrive. Configuring this to double the
vtotal (like some downstream kernels) leads to a frame to take at most
twice before the vsync signal, until hardware TE comes up.
In this case the hardware interrupt responsible for providing this
signal - "disp-te" gpio - is not hooked up to the mdp5 vsync/pp logic at
all. This solves severe panel update issues observed on at least the
Xperia Loire and Tone series, until said gpio is properly hooked up to
an irq.
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210406214726.131534-2-marijn.suijten@somainline.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Follow Bspec 31870 to set recommended tuning values for certain GT
register. These values aren't workarounds per-se, but it's best to
handle them in the same general area of the driver, especially since
there may be real workarounds that update other bits of the same
registers.
At the moment the only value we need to worry about is the
TDS_TIMER setting in FF_MODE2. This setting was previously
described as "Wa_1604555607" on some platforms, but the spec
tells us that we should continue to program this on all current
gen12 platforms, even those that do not have that WA.
Bspec: 31870
v2: Rephrase some comments to make them clearer (Matt)
Cc: Clinton Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Caz Yokoyama <caz.yokoyama@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210324200502.1731265-2-lucas.demarchi@intel.com
As pointed out by the documentation for drm_dp_aux_register(),
drm_dp_aux_init() should be used in situations where the AUX channel for a
display driver can potentially be registered before it's respective DRM
driver. This is the case with Tegra, since the DP aux channel exists as a
platform device instead of being a grandchild of the DRM device.
Since we're about to add a backpointer to a DP AUX channel's respective DRM
device, let's fix this so that we don't potentially allow userspace to use
the AUX channel before we've associated it with it's DRM connector.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210326203807.105754-3-lyude@redhat.com
Looks like that there actually are another subset of laptops on the market
that don't support the Intel HDR backlight interface, but do advertise
support for the VESA DPCD backlight interface despite the fact it doesn't
seem to work.
Note though I'm not entirely clear on this - on one of the machines where
this issue was observed, I also noticed that we appeared to be rejecting
the VBT defined backlight frequency in
intel_dp_aux_vesa_calc_max_backlight(). It's noted in this function that:
/* Use highest possible value of Pn for more granularity of brightness
* adjustment while satifying the conditions below.
* ...
* - FxP is within 25% of desired value.
* Note: 25% is arbitrary value and may need some tweak.
*/
So it's possible that this value might just need to be tweaked, but for now
let's just disable the VESA backlight interface unless it's specified in
the VBT just to be safe. We might be able to try enabling this again by
default in the future.
Fixes: 2227816e64 ("drm/i915/dp: Allow forcing specific interfaces through enable_dpcd_backlight")
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Bugzilla: https://gitlab.freedesktop.org/drm/intel/-/issues/3169
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210318170204.513000-1-lyude@redhat.com
Experimentally have found PV on hvs4 reports fifo full
error with expected settings and does not with one less
This appears as:
[drm:drm_atomic_helper_wait_for_flip_done] *ERROR* [CRTC:82:crtc-3] flip_done timed out
with bit 10 of PV_STAT set "HVS driving pixels when the PV FIFO is full"
Fixes: c8b75bca92 ("drm/vc4: Add KMS support for Raspberry Pi.")
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210318161328.1471556-3-maxime@cerno.tech
