Since there is no connection between the MAC/VLAN and the GID
when using IP-based addressing, the proxy QP1 (running on the
slave) must pass the source-mac, destination-mac, and vlan_id
information separately from the GID. Additionally, the Host
must pass the remote source-mac and vlan_id back to the slave,
This is achieved as follows:
Outgoing MADs:
1. Source MAC: obtained from the CQ completion structure
(struct ib_wc, smac field).
2. Destination MAC: obtained from the tunnel header
3. vlan_id: obtained from the tunnel header.
Incoming MADs
1. The source (i.e., remote) MAC and vlan_id are passed in
the tunnel header to the proxy QP1.
VST mode support:
For outgoing MADs, the vlan_id obtained from the header is
discarded, and the vlan_id specified by the Hypervisor is used
instead.
For incoming MADs, the incoming vlan_id (in the wc) is discarded, and the
"invalid" vlan (0xffff) is substituted when forwarding to the slave.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GIDs are statically distributed, as follows:
PF: gets 16 GIDs
VFs: Remaining GIDS are divided evenly between VFs activated by the driver.
If the division is not even, lower-numbered VFs get an extra GID.
For an IB interface, the number of gids per guest remains as before: one gid per guest.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For IB transport, the host determines the slave GIDs. For ETH (RoCE),
however, the slave's GID is determined by the IP address that the slave
itself assigns to the ETH device used by RoCE.
In this case, the slave must be able to write its GIDs to the HCA gid table
(at the GID indices that slave "owns").
This commit adds processing for the SET_PORT_GID_TABLE opcode modifier
for the SET_PORT command wrapper (so that slaves may modify their GIDS
for RoCE).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This requires the following modifications:
1. Fix build_mlx4_header to properly fill in the ETH fields
2. Adjust mux and demux QP1 flow to support RoCE.
This commit still assumes only one GID per slave for RoCE.
The commit enabling multiple GIDs is a subsequent commit, and
is done separately because of its complexity.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers are allowed to override the default bulk-out buffer size
(endpoint maximum packet size) in order to increase throughput, but it
does not make much sense to allow buffers smaller than the default.
Note that this is already how bulk_in_size is defined.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
We leak an active timer, the hotcpu notifier and all allocated
resources when we exit a namespace. Fix this by introducing a
flow_cache_fini() function where we release the resources before
we exit.
Fixes: ca925cf153 ("flowcache: Make flow cache name space aware")
Reported-by: Jakub Kicinski <moorray3@wp.pl>
Tested-by: Jakub Kicinski <moorray3@wp.pl>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Fan Du <fan.du@windriver.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge the request/release callbacks which are in a separate branch for
consumption by the gpio folks.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
freq table is not per CPU but per policy, so it makes more sense to
keep it within struct cpufreq_policy instead of a per-cpu variable.
This patch does it. Over that, there is no need to set policy->freq_table
to NULL in ->exit(), as policy structure is going to be freed soon.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Device tree nodes are already treated as objects, and we already want to
expose them to userspace which is done using the /proc filesystem today.
Right now the kernel has to do a lot of work to keep the /proc view in
sync with the in-kernel representation. If device_nodes are switched to
be kobjects then the device tree code can be a whole lot simpler. It
also turns out that switching to using /sysfs from /proc results in
smaller code and data size, and the userspace ABI won't change if
/proc/device-tree symlinks to /sys/firmware/devicetree/base.
v7: Add missing sysfs_bin_attr_init()
v6: Add __of_add_property() early init fixes from Pantelis
v5: Rename firmware/ofw to firmware/devicetree
Fix updating property values in sysfs
v4: Fixed build error on Powerpc
Fixed handling of dynamic nodes on powerpc
v3: Fixed handling of duplicate attribute and child node names
v2: switch to using sysfs bin_attributes which solve the problem of
reporting incorrect property size.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
This patch fixes sparse warnings in vlan driver.
It propagates the sparse __percpu attribute from alloc_percpu
into netdev_alloc_pcpu_stats. I expect it may trigger additional
sparse warnings from other drivers that are missing the __percpu
attribute.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for custom reserved memory drivers. Call their init() function
for each reserved region and prepare for using operations provided by them
with by the reserved_mem->ops array.
Based on previous code provided by Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
This patch adds support for dynamically allocated reserved memory regions
declared in device tree. Such regions are defined by 'size', 'alignment'
and 'alloc-ranges' properties.
Based on previous code provided by Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
This patch adds support for static (defined by 'reg' property) reserved
memory regions declared in device tree.
Memory blocks can be reliably reserved only during early boot. This must
happen before the whole memory management subsystem is initialized,
because we need to ensure that the given contiguous blocks are not yet
allocated by kernel. Also it must happen before kernel mappings for the
whole low memory are created, to ensure that there will be no mappings
(for reserved blocks). Typically, all this happens before device tree
structures are unflattened, so we need to get reserved memory layout
directly from fdt.
Based on previous code provided by Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Pull audit namespace fixes from Eric Biederman:
"Starting with 3.14-rc1 the audit code is faulty (think oopses and
races) with respect to how it computes the network namespace of which
socket to reply to, and I happened to notice by chance when reading
through the code.
My testing and the automated build bots don't find any problems with
these fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
audit: Update kdoc for audit_send_reply and audit_list_rules_send
audit: Send replies in the proper network namespace.
audit: Use struct net not pid_t to remember the network namespce to reply in
Add a wakeup_protocols sysfs file which controls the new
rc_dev::enabled_protocols[RC_FILTER_WAKEUP], which is the mask of
protocols that are used for the wakeup filter.
A new RC driver callback change_wakeup_protocol() is called to change
the wakeup protocol mask.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Only a single allowed and enabled protocol mask currently exists in
struct rc_dev, however to support a separate wakeup filter protocol two
of each are needed, ideally as an array.
Therefore make both rc_dev::allowed_protos and rc_dev::enabled_protocols
arrays, update all users to reference the first element
(RC_FILTER_NORMAL), and add a couple more helper functions for drivers
to use for setting the allowed and enabled wakeup protocols.
We also rename allowed_protos to allowed_protocols while we're at it,
which is more consistent with enabled_protocols.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The allowed and enabled protocol masks need to be expanded to be per
filter type in order to support wakeup filter protocol selection. To
ease that process abstract access to the rc_dev::allowed_protos and
rc_dev::enabled_protocols members with inline functions.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Struct v4l2_subdev_edid and the VIDIOC_SUBDEV_G/S_EDID ioctls were
specific for subdevices, but for hardware with a simple video pipeline
you do not need/want to create subdevice nodes to just get/set the EDID.
Move the v4l2_subdev_edid struct to v4l2-common.h and rename as
v4l2_edid. Add the same ioctls to videodev2.h as well, thus allowing
this API to be used with both video nodes and v4l-subdev nodes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds the driver for the LM3646, dual LED Flash driver.
The LM3646 has two 1.5A sync. boost converter with dual white current source.
It is controlled via an I2C compatible interface.
Each flash brightness, torch brightness and enable/disable can be controlled.
Under voltage, input voltage monitor and thermal threshhold Faults are added.
Please refer the datasheet http://www.ti.com/lit/ds/snvs962/snvs962.pdf
Signed-off-by: Daniel Jeong <gshark.jeong@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Three Flash fault are added. V4L2_FLASH_FAULT_UNDER_VOLTAGE for the case low
voltage below the min. limit. V4L2_FLASH_FAULT_INPUT_VOLTAGE for the case
falling input voltage and chip adjust flash current not occur under voltage
event. V4L2_FLASH_FAULT_LED_OVER_TEMPERATURE for the case the temperature
exceed the maximun limit
Signed-off-by: Daniel Jeong <gshark.jeong@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The mcs_spinlock code is not meant (or suitable) as a generic locking
primitive, therefore take it away from the normal includes and place
it in kernel/locking/.
This way the locking primitives implemented there can use it as part
of their implementation but we do not risk it getting used
inapropriately.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/n/tip-byirmpamgr7h25m5kyavwpzx@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In order to allow better integration between the cpuidle framework and the
scheduler, reducing the distance between these two sub-components will
facilitate this integration by moving part of the cpuidle code in the idle
task file and, because idle.c is in the sched directory, we have access to
the scheduler's private structures.
This patch splits the cpuidle_idle_call main entry function into 3 calls
to a newly added API:
1. select the idle state
2. enter the idle state
3. reflect the idle state
The cpuidle_idle_call calls these three functions to implement the main
idle entry function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: rjw@rjwysocki.net
Cc: preeti@linux.vnet.ibm.com
Link: http://lkml.kernel.org/r/1393832934-11625-1-git-send-email-daniel.lezcano@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch adds soft reset controller support for STiH415 and adds new
softreset lines required for other device tree nodes in the header file.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
This patch adds a reset controller node to the SOC device tree and also
adds new header files with reset lines required for other device tree
nodes.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
This patch adds soft reset controller support for STiH415 and adds new
softreset lines required for other device tree nodes in the header file.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
This patch adds a reset controller node to the SOC device tree and also
adds new header files with reset lines required for other device tree
nodes.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Now that all users have been converted to regmap and the config.reg_bits
and config.val_bits can be setted by each user through regmap core API.
So these two params are redundant here.
Since the only control type that left is SND_SOC_REGMAP, so remove it. Drop
the control params and add struct regmap *regmap to simplify the code.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In commit 02f142ecd2 support was added to
start_streaming to return -ENOBUFS if insufficient buffers were queued
for the DMA engine to start. The vb2 core would attempt calling
start_streaming again if another buffer would be queued up.
Later analysis uncovered problems with the queue management if start_streaming
would return an error: the buffers are enqueued to the driver before the
start_streaming op is called, so after an error they are never returned to
the vb2 core. The solution for this is to let the driver return them to
the vb2 core in case of an error while starting the DMA engine. However,
in the case of -ENOBUFS that would be weird: it is not a real error, it
just says that more buffers are needed. Requiring start_streaming to give
them back only to have them requeued again the next time the application
calls QBUF is inefficient.
This patch changes this mechanism: it adds a 'min_buffers_needed' field
to vb2_queue that drivers can set with the minimum number of buffers
required to start the DMA engine. The start_streaming op is only called
if enough buffers are queued. The -ENOBUFS handling has been dropped in
favor of this new method.
Drivers are expected to return buffers back to vb2 core with state QUEUED
if start_streaming would return an error. The vb2 core checks for this
and produces a warning if that didn't happen and it will forcefully
reclaim such buffers to ensure that the internal vb2 core state remains
consistent and all buffer-related resources have been correctly freed
and all op calls have been balanced.
__reqbufs() has been updated to check that at least min_buffers_needed
buffers could be allocated. If fewer buffers were allocated then __reqbufs
will free what was allocated and return -ENOMEM. Based on a suggestion from
Pawel Osciak.
__create_bufs() doesn't do that check, since the use of __create_bufs
assumes some advance scenario where the user might want more control.
Instead streamon will check if enough buffers were allocated to prevent
streaming with fewer than the minimum required number of buffers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
'queued_count' is a bit vague since it is not clear to which queue it
refers to: the vb2 internal list of buffers or the driver-owned list
of buffers.
Rename to make it explicit.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Sometimes sentences in comments ended with a period, and sometimes they
didn't. Add periods. No other changes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If a queue was canceled, then the buf_finish op was never called for the
pending buffers. So add this call to queue_cancel. Before calling buf_finish
set the buffer state to PREPARED, which is the correct state. That way the
states DONE and ERROR will only be seen in buf_finish if streaming is in
progress.
Since buf_finish can now be called from non-streaming state we need to
adapt the handful of drivers that actually need to know this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The buf_finish op should always work, so change the return type to void.
Update the few drivers that use it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Reviewed-by: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When a vb2_queue is freed check if all the mem_ops and queue ops were balanced.
So the number of calls to e.g. buf_finish has to match the number of calls to
buf_prepare, etc.
This code is only enabled if CONFIG_VIDEO_ADV_DEBUG is set.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
