Introduce gpiod_get_optional() and gpiod_get_index_optional() helpers
that make it easier for drivers to handle optional GPIOs.
Currently in order to handle optional GPIOs, a driver needs to special
case error handling for -ENOENT, such as this:
gpio = gpiod_get(dev, "foo");
if (IS_ERR(gpio)) {
if (PTR_ERR(gpio) != -ENOENT)
return PTR_ERR(gpio);
gpio = NULL;
}
if (gpio) {
/* set up GPIO */
}
With these new helpers the above is reduced to:
gpio = gpiod_get_optional(dev, "foo");
if (IS_ERR(gpio))
return PTR_ERR(gpio);
if (gpio) {
/* set up GPIO */
}
While at it, device-managed variants of these functions are also
provided.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Macros to_dss_driver() and to_dss_device() are no longer used, and the
latter doesn't even work. Remove them.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When the driver fails during HW restart or resume, the whole
stack goes into a very confused state with interfaces being
up while the hardware is down etc.
Address this by shutting down everything; we'll run into a
lot of warnings in the process but that's better than having
the whole stack get messed up.
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The framebuffer layer can be a loadable module, which forces
omapfb to be a module as well. However, this breaks the lcd
drivers, which are linked into the omapfb driver but each
have their own module_init() function. To solve this,
we split out the lcd drivers into separate modules and
export omapfb_register_panel, which is the only interface
required between the main omapfb driver and the lcd panel
drivers.
We also have to introduce a new Kconfig symbol for H3, since
that lcd driver has a dependency on TPS65010, which we can
express better in Kconfig than Makefile syntax.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The STMPE has VCC and VIO supply lines, and sometimes (as on
Ux500) this comes from a software-controlled regulator. Make
it possible to supply the STMPE with power from these
regulators.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Similarly, when CONFIG_SYSCTL is not set, ping_group_range should still
work, just that no one can change it. Therefore we should move it out of
sysctl_net_ipv4.c. And, it should not share the same seqlock with
ip_local_port_range.
BTW, rename it to ->ping_group_range instead.
Cc: David S. Miller <davem@davemloft.net>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Reported-by: Stefan de Konink <stefan@konink.de>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_SYSCTL is not set, ip_local_port_range should still work,
just that no one can change it. Therefore we should move it out of sysctl_inet.c.
Also, rename it to ->ip_local_ports instead.
Cc: David S. Miller <davem@davemloft.net>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Reported-by: Stefan de Konink <stefan@konink.de>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull tracing fixes from Steven Rostedt:
"This contains two fixes.
The first is a long standing bug that causes bogus data to show up in
the refcnt field of the module_refcnt tracepoint. It was introduced
by a merge conflict resolution back in 2.6.35-rc days.
The result should be 'refcnt = incs - decs', but instead it did
'refcnt = incs + decs'.
The second fix is to a bug that was introduced in this merge window
that allowed for a tracepoint funcs pointer to be used after it was
freed. Moving the location of where the probes are released solved
the problem"
* tag 'trace-fixes-v3.15-rc4-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracepoint: Fix use of tracepoint funcs after rcu free
trace: module: Maintain a valid user count
Pull mmc/rtsx revert from Lee Jones.
* tag 'mfd-mmc-fixes-3.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mmc: rtsx: Revert "mmc: rtsx: add support for pre_req and post_req"
Use fh_fsid when reffering to the fsid part of the filehandle. The
variable length auth field envisioned in nfsfh wasn't ever implemented.
Also clean up some lose ends around this and document the file handle
format better.
Btw, why do we even export nfsfh.h to userspace? The file handle very
much is kernel private, and nothing in nfs-utils include the header
either.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
This patch adds support to store RSSI for connection when reply for
HCI_Read_RSSI is received.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now, all platform is using new style rsnd_dai_platform_info.
Keeping compatibility is no longer needed.
We can cleanup code.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
On platforms that use cpufreq_for_each_* macros, build fails if
CONFIG_CPU_FREQ=n, e.g. ARM/shmobile/koelsch/non-multiplatform:
drivers/built-in.o: In function `clk_round_parent':
clkdev.c:(.text+0xcf168): undefined reference to `cpufreq_next_valid'
drivers/built-in.o: In function `clk_rate_table_find':
clkdev.c:(.text+0xcf820): undefined reference to `cpufreq_next_valid'
make[3]: *** [vmlinux] Error 1
Fix this making cpufreq_next_valid function inline and move it to
cpufreq.h.
Fixes: 27e289dce2 (cpufreq: Introduce macros for cpufreq_frequency_table iteration)
Reported-and-tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When trying to generate documentation, at least xmldocs, we get the
following warning:
Warning(include/net/cfg80211.h:461): No description found for parameter 'nl80211_iftype'
Fix it by adding the iftype argument name to the
cfg80211_chandef_dfs_required() function declaration.
Reported-and-tested-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit c42deffd5b.
commit <mmc: rtsx: add support for pre_req and post_req> did use
mutex_unlock() in tasklet, but mutex_unlock() can't be used in
tasklet(atomic context). The driver needs to use mutex to avoid
concurrency, so we can't use tasklet here, the patch need to be
removed.
The spinlock host->lock and pcr->lock may deadlock, one way to solve
the deadlock is remove host->lock in sd_isr_done_transfer(), but if
using workqueue the we can avoid using the spinlock and also avoid
the problem.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch provides similar led functional of
420f973 thinkpad-acpi: Add mute and mic-mute LED functionality
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Pull radeon mullins support from Dave Airlie:
"This is support for the new AMD mullins APU, it pretty much just adds
support to the driver in the all the right places, and is pretty low
risk wrt other GPUs"
Oh well. I guess it ends up fitting under "support new hardware" for
merging late.
* 'drm-radeon-mullins' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: add pci ids for Mullins
drm/radeon: add Mullins VCE support
drm/radeon: modesetting updates for Mullins.
drm/radeon: dpm updates for KV/KB
drm/radeon: add Mullins dpm support.
drm/radeon: add Mullins UVD support.
drm/radeon: update cik init for Mullins.
drm/radeon: add Mullins chip family
Pull drm fixes from Dave Airlie:
"radeon, i915 and nouveau fixes, all fixes for regressions or black
screens, or possible oopses"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: lower the ref * post PLL maximum
drm/radeon: check that we have a clock before PLL setup
drm/radeon: drm/radeon: add missing radeon_semaphore_free to error path
drm/radeon: Fix num_banks calculation for SI
agp: info leak in agpioc_info_wrap()
drm/gm107/gr: bump attrib cb size quite a bit
drm/nouveau: fix another lock unbalance in nouveau_crtc_page_flip
drm/nouveau/bios: fix shadowing from PROM on big-endian systems
drm/nouveau/acpi: allow non-optimus setups to load vbios from acpi
drm/radeon/dp: check for errors in dpcd reads
drm/radeon: avoid high jitter with small frac divs
drm/radeon: check buffer relocation offset
drm/radeon: use pflip irq on R600+ v2
drm/radeon/uvd: use lower clocks on old UVD to boot v2
drm/i915: don't try DP_LINK_BW_5_4 on HSW ULX
drm/i915: Sanitize the enable_ppgtt module option once
drm/i915: Break encoder->crtc link separately in intel_sanitize_crtc()
If CONFIG_OF is not set, make of_mdiobus_register() call
mdiobus_register() instead of returning -ENOSYS.
This way, we can just call of_mdiobus_register() from all DT-enabled
drivers to handle the compat cases.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new platform data flag "use_eeprom" that indicates that the eeprom
found on the card itself should be used instead of the one present in
the platform data.
This allows to override the MAC address of a PCI card while preserving
the eeprom data from the card itself.
The default behavior is preserved.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit 8f0ea0fe3a (snmp: reduce percpu needs by 50%)
reduced snmp array size to 1, so technically it doesn't have to be
an array any more. What's more, after the following commit:
commit 933393f58f
Date: Thu Dec 22 11:58:51 2011 -0600
percpu: Remove irqsafe_cpu_xxx variants
We simply say that regular this_cpu use must be safe regardless of
preemption and interrupt state. That has no material change for x86
and s390 implementations of this_cpu operations. However, arches that
do not provide their own implementation for this_cpu operations will
now get code generated that disables interrupts instead of preemption.
probably no arch wants to have SNMP_ARRAY_SZ == 2. At least after
almost 3 years, no one complains.
So, just convert the array to a single pointer and remove snmp_mib_init()
and snmp_mib_free() as well.
Cc: Christoph Lameter <cl@linux.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The quoted text and figure are from RFC 6040 ("Tunnelling of Explicit
Congestion Notification").
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Old ADCs, as present on the sam9rl and the sam9g45 don't have a TSMR register
and the touchscreen support should be handled differently.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
num_channels and registers are not used anymore since they are defined inside
the driver and assigned by matching the id_table.
Also, struct at91_adc_reg_desc is now only used inside the driver.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
AT91 slow clk is a clk multiplexer.
In some SoCs (sam9x5, sama5, sam9g45 families) this multiplexer can
choose among 2 sources: an internal RC oscillator circuit and an oscillator
using an external crystal.
In other Socs (sam9260 family) the multiplexer source is hardcoded with
the OSCSEL signal.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Right now we just pick the first CPU in the mask, but that can
easily overload that one. Add some basic batching and round-robin
all the entries in the mask instead.
Signed-off-by: Jens Axboe <axboe@fb.com>
There are some code paths in the kernel that need to do some preparations
before it calls a tracepoint. As that code is worthless overhead when
the tracepoint is not enabled, it would be prudent to have that code
only run when the tracepoint is active. To accomplish this, all tracepoints
now get a static inline function called "trace_<tracepoint-name>_enabled()"
which returns true when the tracepoint is enabled and false otherwise.
As an added bonus, that function uses the static_key of the tracepoint
such that no branch is needed.
if (trace_mytracepoint_enabled()) {
arg = process_tp_arg();
trace_mytracepoint(arg);
}
Will keep the "process_tp_arg()" (which may be expensive to run) from
being executed when the tracepoint isn't enabled.
It's best to encapsulate the tracepoint itself in the if statement
just to keep races. For example, if you had:
if (trace_mytracepoint_enabled())
arg = process_tp_arg();
trace_mytracepoint(arg);
There's a chance that the tracepoint could be enabled just after the
if statement, and arg will be undefined when calling the tracepoint.
Link: http://lkml.kernel.org/r/20140506094407.507b6435@gandalf.local.home
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Retrieve DMA configuration from DT and setup platform device's DMA
parameters. The DMA configuration in DT has to be specified using
"dma-ranges" and "dma-coherent" properties if supported.
We setup dma_pfn_offset using "dma-ranges" and dma_coherent_ops
using "dma-coherent" device tree properties.
The set_arch_dma_coherent_ops macro has to be defined by arch if
it supports coherent dma_ops. Otherwise, set_arch_dma_coherent_ops() is
declared as nop.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
yield_task_dl() is broken:
o it forces current to be throttled setting its runtime to zero;
o it sets current's dl_se->dl_new to one, expecting that dl_task_timer()
will queue it back with proper parameters at replenish time.
Unfortunately, dl_task_timer() has this check at the very beginning:
if (!dl_task(p) || dl_se->dl_new)
goto unlock;
So, it just bails out and the task is never replenished. It actually
yielded forever.
To fix this, introduce a new flag indicating that the task properly yielded
the CPU before its current runtime expired. While this is a little overdoing
at the moment, the flag would be useful in the future to discriminate between
"good" jobs (of which remaining runtime could be reclaimed, i.e. recycled)
and "bad" jobs (for which dl_throttled task has been set) that needed to be
stopped.
Reported-by: yjay.kim <yjay.kim@lge.com>
Signed-off-by: Juri Lelli <juri.lelli@gmail.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140429103953.e68eba1b2ac3309214e3dc5a@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit d191bd8de8 ("ASoC: snd_soc_codec includes snd_soc_component") removed the
last user of the num_dai field. Also remove the field itself.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The global card list was removed in commit b19e6e7b7 ("ASoC: core: Use driver
core probe deferral"). The 'list' field of the snd_soc_card struct has been
unused since then. This patch removes the field.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit f0fba2ad1 ("ASoC: multi-component - ASoC Multi-Component Support") added
a per card list that keeps track of all the DAIs that have been registered with
the card, but the list has never been used. This patch removes it again.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
