The ssbi driver assumes that the device is DT based. Remove the
platform data structs that will never be used and hide the enum
in the only C file that uses it.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use the VERSIONCRC to determine the exact device version. According to
the datasheet this register can be used as device identifier. The
identification is needed since some tps6586x regulators use a different
voltage table.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
LP3943 has 16 output pins which can be used as GPIO expander and PWM generator.
* Regmap I2C interface for R/W LP3943 registers
* Atomic operations for output pin assignment
The driver should check whether requested pin is available or not.
If the pin is already used, pin request returns as a failure.
A driver data, 'pin_used' is checked when gpio_request() and
pwm_request() are called. If the pin is available, then pin_used is set.
And it is cleared when gpio_free() and pwm_free().
* Device tree support
Compatible strings for GPIO and PWM driver.
LP3943 platform data is PWM related, so parsing the device tree is
implemented in the PWM driver.
Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This deletes the special AB8500 GPIO platform data passing
header and merges the few remaining contents down into the
abx500 pinctrl driver which handles the abx500 GPIO device.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This deletes all instances where the AB8500 GPIO platform
data is passed around. It is completely unused in the kernel
now, so it does not hurt anyone.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds max14577 core/irq driver to support MUIC(Micro USB IC)
device and charger device and support irq domain method to control
internal interrupt of max14577 device. Also, this patch supports DT
binding with max14577_i2c_parse_dt().
The MAXIM 14577 chip contains Micro-USB Interface Circuit and Li+ Battery
Charger. It contains accessory and USB charger detection logic. It supports
USB 2.0 Hi-Speed, UART and stereo audio signals over Micro-USB connector.
The battery charger is compliant with the USB Battery Charging Specification
Revision 1.1. It has also SFOUT LDO output for powering USB devices.
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
cache_chain_mutex has been replaced by slab_mutex. Fix this remaining
outdated comment.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull USB updates from Greg KH:
"Here's the big USB pull request for 3.14-rc1
Lots of little things all over the place, and the usual USB gadget
updates, and XHCI fixes (some for an issue reported by a lot of
people). USB PHY updates as well as chipidea updates and fixes.
All of these have been in the linux-next tree with no reported issues"
* tag 'usb-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (318 commits)
usb: chipidea: udc: using MultO at TD as real mult value for ISO-TX
usb: chipidea: need to mask INT_STATUS when write otgsc
usb: chipidea: put hw_phymode_configure before ci_usb_phy_init
usb: chipidea: Fix Internal error: : 808 [#1] ARM related to STS flag
usb: chipidea: imx: set CI_HDRC_IMX28_WRITE_FIX for imx28
usb: chipidea: add freescale imx28 special write register method
usb: ehci: add freescale imx28 special write register method
usb: core: check for valid id_table when using the RefId feature
usb: cdc-wdm: resp_count can be 0 even if WDM_READ is set
usb: core: bail out if user gives an unknown RefId when using new_id
usb: core: allow a reference device for new_id
usb: core: add sanity checks when using bInterfaceClass with new_id
USB: image: correct spelling mistake in comment
USB: c67x00: correct spelling mistakes in comments
usb: delete non-required instances of include <linux/init.h>
usb:hub set hub->change_bits when over-current happens
Revert "usb: chipidea: imx: set CI_HDRC_IMX28_WRITE_FIX for imx28"
xhci: Set scatter-gather limit to avoid failed block writes.
xhci: Avoid infinite loop when sg urb requires too many trbs
usb: gadget: remove unused variable in gr_queue_int()
...
Pull tty/serial driver updates from Greg KH:
"Here's the big tty/serial driver pull request for 3.14-rc1
There are a number of n_tty fixes and cleanups, and some serial driver
bugfixes, and we got rid of one obsolete driver, making this series
remove more lines than added, always a nice surprise.
All of these have been in linux-next with no reports of issues"
* tag 'tty-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (60 commits)
tty/serial: at91: disable uart timer at start of shutdown
serial: 8250: enable UART_BUG_NOMSR for Tegra
tty/serial: at91: reset rx_ring when port is shutdown
tty/serial: at91: fix race condition in atmel_serial_remove
tty/serial: at91: Handle shutdown more safely
serial: sirf: correct condition for fetching dma buffer into tty
serial: sirf: provide pm entries of uart_ops
serial: sirf: use PM macro initialize PM functions
serial: clps711x: Enable driver compilation with COMPILE_TEST
serial: clps711x: Add support for N_IRDA line discipline
tty: synclink: avoid sleep_on race
tty/amiserial: avoid interruptible_sleep_on
tty: delete non-required instances of include <linux/init.h>
tty: an overflow of multiplication in drivers/tty/cyclades.c
serial: Remove old SC26XX driver
serial: add support for 200 v3 series Titan card
serial: 8250: Fix initialisation of Quatech cards with the AMCC PCI chip
tty: Removing the deprecated function tty_vhangup_locked()
TTY/n_gsm: Removing the wrong tty_unlock/lock() in gsm_dlci_release()
tty/serial: at91: document clock properties
...
Pull staging driver tree changes from Greg KH:
"Here's the big drivers/staging/ update for 3.14-rc1
Lots and lots of cleanups, IIO driver updates are also mixed in here
due to the subsystem still crossing staging and drivers/iio/, and the
dwc2 driver is moved out of staging. There's a new driver (rts5208),
which ends up making us adding more lines than removing, but overall
there was lots of work toward moving code out of here, which was good
All of this has been in linux-next with no reported issues"
* tag 'staging-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1084 commits)
lustre: delete linux/lustre_debug.h
staging: lustre: remove some unused debug macros
usb: dwc2: move device tree bindings doc to correct place
staging: vt6656: sparse fixes: iwctl_giwgenie use memcpy.
staging: vt6656: sparse fixes: iwctl_siwgenie use memcpy.
staging: vt6656: sparse fixes ethtool_ioctl Use struct ifreq *
staging: vt6656: sparse fixes: dpc.c missing dpc.h
staging: lustre: libcfs_debug: small whitespace cleanups
staging: lustre: libcfs_debug.h: remove extra blank lines
staging: lustre: libcfs_debug.h: Align backslashes in macros
staging: lustre: libcfs_debug.h: align define values
staging: tidspbridge: adjust error return code (bugfix)
Staging: rts5139: rts51x_card: fixed style issues
staging: wlags49_h2: Fix "do not use C99 //" in wl_cs.h, wl_enc.h wl_main.h and wl_wext.h
Staging: rtl8188eu: Fixed "foo * bar" related coding style issues
Staging: rtl8188eu: Fixed required spaces after ',' and around '=' and '=='
staging: vt6655: Fix memory leak in wpa_ioctl()
imx-drm: parallel-display: honor 'native-mode' property when selecting video mode from DT
staging: drm/imx: don't drop crtc offsets when doing pageflip
staging: drm/imx: handle framebuffer offsets correctly
...
Pull driver core / sysfs patches from Greg KH:
"Here's the big driver core and sysfs patch set for 3.14-rc1.
There's a lot of work here moving sysfs logic out into a "kernfs" to
allow other subsystems to also have a virtual filesystem with the same
attributes of sysfs (handle device disconnect, dynamic creation /
removal as needed / unneeded, etc)
This is primarily being done for the cgroups filesystem, but the goal
is to also move debugfs to it when it is ready, solving all of the
known issues in that filesystem as well. The code isn't completed
yet, but all should be stable now (there is a big section that was
reverted due to problems found when testing)
There's also some other smaller fixes, and a driver core addition that
allows for a "collection" of objects, that the DRM people will be
using soon (it's in this tree to make merges after -rc1 easier)
All of this has been in linux-next with no reported issues"
* tag 'driver-core-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (113 commits)
kernfs: associate a new kernfs_node with its parent on creation
kernfs: add struct dentry declaration in kernfs.h
kernfs: fix get_active failure handling in kernfs_seq_*()
Revert "kernfs: fix get_active failure handling in kernfs_seq_*()"
Revert "kernfs: replace kernfs_node->u.completion with kernfs_root->deactivate_waitq"
Revert "kernfs: remove KERNFS_ACTIVE_REF and add kernfs_lockdep()"
Revert "kernfs: remove KERNFS_REMOVED"
Revert "kernfs: restructure removal path to fix possible premature return"
Revert "kernfs: invoke kernfs_unmap_bin_file() directly from __kernfs_remove()"
Revert "kernfs: remove kernfs_addrm_cxt"
Revert "kernfs: make kernfs_get_active() block if the node is deactivated but not removed"
Revert "kernfs: implement kernfs_{de|re}activate[_self]()"
Revert "kernfs, sysfs, driver-core: implement kernfs_remove_self() and its wrappers"
Revert "pci: use device_remove_file_self() instead of device_schedule_callback()"
Revert "scsi: use device_remove_file_self() instead of device_schedule_callback()"
Revert "s390: use device_remove_file_self() instead of device_schedule_callback()"
Revert "sysfs, driver-core: remove unused {sysfs|device}_schedule_callback_owner()"
Revert "kernfs: remove unnecessary NULL check in __kernfs_remove()"
kernfs: remove unnecessary NULL check in __kernfs_remove()
drivers/base: provide an infrastructure for componentised subsystems
...
Pull char/misc driver patches from Greg KH:
"Here's the big char/misc driver patches for 3.14-rc1.
Lots of little things, and a new "big" driver, genwqe. Full details
are in the shortlog"
* tag 'char-misc-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (90 commits)
mei: limit the number of consecutive resets
mei: revamp mei reset state machine
drivers/char: don't use module_init in non-modular ttyprintk.c
VMCI: fix error handling path when registering guest driver
extcon: gpio: Add power resume support
Documentation: HOWTO: Updates on subsystem trees, patchwork, -next (vs. -mm) in ko_KR
Documentation: HOWTO: update for 2.6.x -> 3.x versioning in ko_KR
Documentation: HOWTO: update stable address in ko_KR
Documentation: HOWTO: update LXR web link in ko_KR
char: nwbutton: open-code interruptible_sleep_on
mei: fix syntax in comments and debug output
mei: nfc: mei_nfc_free has to be called under lock
mei: use hbm idle state to prevent spurious resets
mei: do not run reset flow from the interrupt thread
misc: genwqe: fix return value check in genwqe_device_create()
GenWQE: Fix warnings for sparc
GenWQE: Fix compile problems for Alpha
Documentation/misc-devices/mei/mei-amt-version.c: remove unneeded call of mei_deinit()
GenWQE: Rework return code for flash-update ioctl
sgi-xp: open-code interruptible_sleep_on_timeout
...
Pull ARM64 updates from Catalin Marinas:
- CPU suspend support on top of PSCI (firmware Power State Coordination
Interface)
- jump label support
- CMA can now be enabled on arm64
- HWCAP bits for crypto and CRC32 extensions
- optimised percpu using tpidr_el1 register
- code cleanup
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (42 commits)
arm64: fix typo in entry.S
arm64: kernel: restore HW breakpoint registers in cpu_suspend
jump_label: use defined macros instead of hard-coding for better readability
arm64, jump label: optimize jump label implementation
arm64, jump label: detect %c support for ARM64
arm64: introduce aarch64_insn_gen_{nop|branch_imm}() helper functions
arm64: move encode_insn_immediate() from module.c to insn.c
arm64: introduce interfaces to hotpatch kernel and module code
arm64: introduce basic aarch64 instruction decoding helpers
arm64: dts: Reduce size of virtio block device for foundation model
arm64: Remove unused __data_loc variable
arm64: Enable CMA
arm64: Warn on NULL device structure for dma APIs
arm64: Add hwcaps for crypto and CRC32 extensions.
arm64: drop redundant macros from read_cpuid()
arm64: Remove outdated comment
arm64: cmpxchg: update macros to prevent warnings
arm64: support single-step and breakpoint handler hooks
ARM64: fix framepointer check in unwind_frame
ARM64: check stack pointer in get_wchan
...
This is needed for reporting the max GPU engine clock
in OpenCL. This just reports the max possible engine
clock, it does not take into account current conditions
that may limit that clock.
v2: fix query number for merge with 3.13
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Pull x32 uapi changes from Peter Anvin:
"This is the first few of a set of patches by H.J. Lu to make the
kernel uapi headers usable for x32, as required by some non-glibc
libcs.
These particular patches make the stat and statfs structures usable"
* 'x86-x32-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, x32: Use __kernel_long_t for __statfs_word
x86, x32: Use __kernel_long_t/__kernel_ulong_t in x86-64 stat.h
Pull x86 RAS changes from Ingo Molnar:
- SCI reporting for other error types not only correctable ones
- GHES cleanups
- Add the functionality to override error reporting agents as some
machines are sporting a new extended error logging capability which,
if done properly in the BIOS, makes a corresponding EDAC module
redundant
- PCIe AER tracepoint severity levels fix
- Error path correction for the mce device init
- MCE timer fix
- Add more flexibility to the error injection (EINJ) debugfs interface
* 'x86-ras-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, mce: Fix mce_start_timer semantics
ACPI, APEI, GHES: Cleanup ghes memory error handling
ACPI, APEI: Cleanup alignment-aware accesses
ACPI, APEI, GHES: Do not report only correctable errors with SCI
ACPI, APEI, EINJ: Changes to the ACPI/APEI/EINJ debugfs interface
ACPI, eMCA: Combine eMCA/EDAC event reporting priority
EDAC, sb_edac: Modify H/W event reporting policy
EDAC: Add an edac_report parameter to EDAC
PCI, AER: Fix severity usage in aer trace event
x86, mce: Call put_device on device_register failure
Pull x86 EFI changes from Ingo Molnar:
"This consists of two main parts:
- New static EFI runtime services virtual mapping layout which is
groundwork for kexec support on EFI (Borislav Petkov)
- EFI kexec support itself (Dave Young)"
* 'x86-efi-kexec-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
x86/efi: parse_efi_setup() build fix
x86: ksysfs.c build fix
x86/efi: Delete superfluous global variables
x86: Reserve setup_data ranges late after parsing memmap cmdline
x86: Export x86 boot_params to sysfs
x86: Add xloadflags bit for EFI runtime support on kexec
x86/efi: Pass necessary EFI data for kexec via setup_data
efi: Export EFI runtime memory mapping to sysfs
efi: Export more EFI table variables to sysfs
x86/efi: Cleanup efi_enter_virtual_mode() function
x86/efi: Fix off-by-one bug in EFI Boot Services reservation
x86/efi: Add a wrapper function efi_map_region_fixed()
x86/efi: Remove unused variables in __map_region()
x86/efi: Check krealloc return value
x86/efi: Runtime services virtual mapping
x86/mm/cpa: Map in an arbitrary pgd
x86/mm/pageattr: Add last levels of error path
x86/mm/pageattr: Add a PUD error unwinding path
x86/mm/pageattr: Add a PTE pagetable populating function
x86/mm/pageattr: Add a PMD pagetable populating function
...
Add the Intel manufacturer Id.
Tested with Intel JS29F32G08ACMD1(4096 + 224) which is ONFI 2.0 compliant
nand.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add the manufactor ID for SanDisk.
Make preparation for SanDisk SDTNRGAMA-008G.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Pull scheduler changes from Ingo Molnar:
- Add the initial implementation of SCHED_DEADLINE support: a real-time
scheduling policy where tasks that meet their deadlines and
periodically execute their instances in less than their runtime quota
see real-time scheduling and won't miss any of their deadlines.
Tasks that go over their quota get delayed (Available to privileged
users for now)
- Clean up and fix preempt_enable_no_resched() abuse all around the
tree
- Do sched_clock() performance optimizations on x86 and elsewhere
- Fix and improve auto-NUMA balancing
- Fix and clean up the idle loop
- Apply various cleanups and fixes
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (60 commits)
sched: Fix __sched_setscheduler() nice test
sched: Move SCHED_RESET_ON_FORK into attr::sched_flags
sched: Fix up attr::sched_priority warning
sched: Fix up scheduler syscall LTP fails
sched: Preserve the nice level over sched_setscheduler() and sched_setparam() calls
sched/core: Fix htmldocs warnings
sched/deadline: No need to check p if dl_se is valid
sched/deadline: Remove unused variables
sched/deadline: Fix sparse static warnings
m68k: Fix build warning in mac_via.h
sched, thermal: Clean up preempt_enable_no_resched() abuse
sched, net: Fixup busy_loop_us_clock()
sched, net: Clean up preempt_enable_no_resched() abuse
sched/preempt: Fix up missed PREEMPT_NEED_RESCHED folding
sched/preempt, locking: Rework local_bh_{dis,en}able()
sched/clock, x86: Avoid a runtime condition in native_sched_clock()
sched/clock: Fix up clear_sched_clock_stable()
sched/clock, x86: Use a static_key for sched_clock_stable
sched/clock: Remove local_irq_disable() from the clocks
sched/clock, x86: Rewrite cyc2ns() to avoid the need to disable IRQs
...
Pull perf updates from Ingo Molnar:
"Kernel side changes:
- Add Intel RAPL energy counter support (Stephane Eranian)
- Clean up uprobes (Oleg Nesterov)
- Optimize ring-buffer writes (Peter Zijlstra)
Tooling side changes, user visible:
- 'perf diff':
- Add column colouring improvements (Ramkumar Ramachandra)
- 'perf kvm':
- Add guest related improvements, including allowing to specify a
directory with guest specific /proc information (Dongsheng Yang)
- Add shell completion support (Ramkumar Ramachandra)
- Add '-v' option (Dongsheng Yang)
- Support --guestmount (Dongsheng Yang)
- 'perf probe':
- Support showing source code, asking for variables to be collected
at probe time and other 'perf probe' operations that use DWARF
information.
This supports only binaries with debugging information at this
time, detached debuginfo (aka debuginfo packages) support should
come in later patches (Masami Hiramatsu)
- 'perf record':
- Rename --no-delay option to --no-buffering, better reflecting its
purpose and freeing up '--delay' to take the place of
'--initial-delay', so that 'record' and 'stat' are consistent
(Arnaldo Carvalho de Melo)
- Default the -t/--thread option to no inheritance (Adrian Hunter)
- Make per-cpu mmaps the default (Adrian Hunter)
- 'perf report':
- Improve callchain processing performance (Frederic Weisbecker)
- Retain bfd reference to lookup source line numbers, greatly
optimizing, among other use cases, 'perf report -s srcline'
(Adrian Hunter)
- Improve callchain processing performance even more (Namhyung Kim)
- Add a perf.data file header window in the 'perf report' TUI,
associated with the 'i' hotkey, providing a counterpart to the
--header option in the stdio UI (Namhyung Kim)
- 'perf script':
- Add an option in 'perf script' to print the source line number
(Adrian Hunter)
- Add --header/--header-only options to 'script' and 'report', the
default is not tho show the header info, but as this has been the
default for some time, leave a single line explaining how to
obtain that information (Jiri Olsa)
- Add options to show comm, fork, exit and mmap PERF_RECORD_ events
(Namhyung Kim)
- Print callchains and symbols if they exist (David Ahern)
- 'perf timechart'
- Add backtrace support to CPU info
- Print pid along the name
- Add support for CPU topology
- Add new option --highlight'ing threads, be it by name or, if a
numeric value is provided, that run more than given duration
(Stanislav Fomichev)
- 'perf top':
- Make 'perf top -g' refer to callchains, for consistency with
other tools (David Ahern)
- 'perf trace':
- Handle old kernels where the "raw_syscalls" tracepoints were
called plain "syscalls" (David Ahern)
- Remove thread summary coloring, by Pekka Enberg.
- Honour -m option in 'trace', the tool was offering the option to
set the mmap size, but wasn't using it when doing the actual mmap
on the events file descriptors (Jiri Olsa)
- generic:
- Backport libtraceevent plugin support (trace-cmd repository, with
plugins for jbd2, hrtimer, kmem, kvm, mac80211, sched_switch,
function, xen, scsi, cfg80211 (Jiri Olsa)
- Print session information only if --stdio is given (Namhyung Kim)
Tooling side changes, developer visible (plumbing):
- Improve 'perf probe' exit path, release resources (Masami
Hiramatsu)
- Improve libtraceevent plugins exit path, allowing the registering
of an unregister handler to be called at exit time (Namhyung Kim)
- Add an alias to the build test makefile (make -C tools/perf
build-test) (Namhyung Kim)
- Get rid of die() and friends (good riddance!) in libtraceevent
(Namhyung Kim)
- Fix cross build problems related to pkgconfig and CROSS_COMPILE not
being propagated to the feature tests, leading to features being
tested in the host and then being enabled on the target (Mark
Rutland)
- Improve forked workload error reporting by sending the errno in the
signal data queueing integer field, using sigqueue and by doing the
signal setup in the evlist methods, removing open coded equivalents
in various tools (Arnaldo Carvalho de Melo)
- Do more auto exit cleanup chores in the 'evlist' destructor, so
that the tools don't have to all do that sequence (Arnaldo Carvalho
de Melo)
- Pack 'struct perf_session_env' and 'struct trace' (Arnaldo Carvalho
de Melo)
- Add test for building detached source tarballs (Arnaldo Carvalho de
Melo)
- Move some header files (tools/perf/ to tools/include/ to make them
available to other tools/ dwelling codebases (Namhyung Kim)
- Move logic to warn about kptr_restrict'ed kernels to separate
function in 'report' (Arnaldo Carvalho de Melo)
- Move hist browser selection code to separate function (Arnaldo
Carvalho de Melo)
- Move histogram entries collapsing to separate function (Arnaldo
Carvalho de Melo)
- Introduce evlist__for_each() & friends (Arnaldo Carvalho de Melo)
- Automate setup of FEATURE_CHECK_(C|LD)FLAGS-all variables (Jiri
Olsa)
- Move arch setup into seprate Makefile (Jiri Olsa)
- Make libtraceevent install target quieter (Jiri Olsa)
- Make tests/make output more compact (Jiri Olsa)
- Ignore generated files in feature-checks (Chunwei Chen)
- Introduce pevent_filter_strerror() in libtraceevent, similar in
purpose to libc's strerror() function (Namhyung Kim)
- Use perf_data_file methods to write output file in 'record' and
'inject' (Jiri Olsa)
- Use pr_*() functions where applicable in 'report' (Namhyumg Kim)
- Add 'machine' 'addr_location' struct to have full picture (machine,
thread, map, symbol, addr) for a (partially) resolved address,
reducing function signatures (Arnaldo Carvalho de Melo)
- Reduce code duplication in the histogram entry creation/insertion
(Arnaldo Carvalho de Melo)
- Auto allocate annotation histogram data structures (Arnaldo
Carvalho de Melo)
- No need to test against NULL before calling free, also set freed
memory in struct pointers to NULL, to help fixing use after free
bugs (Arnaldo Carvalho de Melo)
- Rename some struct DSO binary_type related members and methods, to
clarify its purpose and need for differentiation (symtab_type, ie
one is about the files .text, CFI, etc, i.e. its binary contents,
and the other is about where the symbol table came from (Arnaldo
Carvalho de Melo)
- Convert to new topic libraries, starting with an API one (sysfs,
debugfs, etc), renaming liblk in the process (Borislav Petkov)
- Get rid of some more panic() like error handling in libtraceevent.
(Namhyung Kim)
- Get rid of panic() like calls in libtraceevent (Namyung Kim)
- Start carving out symbol parsing routines (perf, just moving
routines to topic files in tools/lib/symbol/, tools that want to
use it need to integrate it directly, ie no
tools/lib/symbol/Makefile is provided (Arnaldo Carvalho de Melo)
- Assorted refactoring patches, moving code around and adding utility
evlist methods that will be used in the IPT patchset (Adrian
Hunter)
- Assorted mmap_pages handling fixes (Adrian Hunter)
- Several man pages typo fixes (Dongsheng Yang)
- Get rid of several die() calls in libtraceevent (Namhyung Kim)
- Use basename() in a more robust way, to avoid problems related to
different system library implementations for that function
(Stephane Eranian)
- Remove open coded management of short_name_allocated member (Adrian
Hunter)
- Several cleanups in the "dso" methods, constifying some parameters
and renaming some fields to clarify its purpose (Arnaldo Carvalho
de Melo)
- Add per-feature check flags, fixing libunwind related build
problems on some architectures (Jean Pihet)
- Do not disable source line lookup just because of one failure.
(Adrian Hunter)
- Several 'perf kvm' man page corrections (Dongsheng Yang)
- Correct the message in feature-libnuma checking, swowing the right
devel package names for various distros (Dongsheng Yang)
- Polish 'readn()' function and introduce its counterpart,
'writen()' (Jiri Olsa)
- Start moving timechart state from global variables to a 'perf_tool'
derived 'timechart' struct (Arnaldo Carvalho de Melo)
... and lots of fixes and improvements I forgot to list"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (282 commits)
perf tools: Remove unnecessary callchain cursor state restore on unmatch
perf callchain: Spare double comparison of callchain first entry
perf tools: Do proper comm override error handling
perf symbols: Export elf_section_by_name and reuse
perf probe: Release all dynamically allocated parameters
perf probe: Release allocated probe_trace_event if failed
perf tools: Add 'build-test' make target
tools lib traceevent: Unregister handler when xen plugin is unloaded
tools lib traceevent: Unregister handler when scsi plugin is unloaded
tools lib traceevent: Unregister handler when jbd2 plugin is is unloaded
tools lib traceevent: Unregister handler when cfg80211 plugin is unloaded
tools lib traceevent: Unregister handler when mac80211 plugin is unloaded
tools lib traceevent: Unregister handler when sched_switch plugin is unloaded
tools lib traceevent: Unregister handler when kvm plugin is unloaded
tools lib traceevent: Unregister handler when kmem plugin is unloaded
tools lib traceevent: Unregister handler when hrtimer plugin is unloaded
tools lib traceevent: Unregister handler when function plugin is unloaded
tools lib traceevent: Add pevent_unregister_print_function()
tools lib traceevent: Add pevent_unregister_event_handler()
tools lib traceevent: fix pointer-integer size mismatch
...
Pull RCU updates from Ingo Molnar:
- add RCU torture scripts/tooling
- static analysis improvements
- update RCU documentation
- miscellaneous fixes
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (52 commits)
rcu: Remove "extern" from function declarations in kernel/rcu/rcu.h
rcu: Remove "extern" from function declarations in include/linux/*rcu*.h
rcu/torture: Dynamically allocate SRCU output buffer to avoid overflow
rcu: Don't activate RCU core on NO_HZ_FULL CPUs
rcu: Warn on allegedly impossible rcu_read_unlock_special() from irq
rcu: Add an RCU_INITIALIZER for global RCU-protected pointers
rcu: Make rcu_assign_pointer's assignment volatile and type-safe
bonding: Use RCU_INIT_POINTER() for better overhead and for sparse
rcu: Add comment on evaluate-once properties of rcu_assign_pointer().
rcu: Provide better diagnostics for blocking in RCU callback functions
rcu: Improve SRCU's grace-period comments
rcu: Fix CONFIG_RCU_FANOUT_EXACT for odd fanout/leaf values
rcu: Fix coccinelle warnings
rcutorture: Stop tracking FSF's postal address
rcutorture: Move checkarg to functions.sh
rcutorture: Flag errors and warnings with color coding
rcutorture: Record results from repeated runs of the same test scenario
rcutorture: Test summary at end of run with less chattiness
rcutorture: Update comment in kvm.sh listing typical RCU trace events
rcutorture: Add tracing-enabled version of TREE08
...
Pull core locking changes from Ingo Molnar:
- futex performance increases: larger hashes, smarter wakeups
- mutex debugging improvements
- lots of SMP ordering documentation updates
- introduce the smp_load_acquire(), smp_store_release() primitives.
(There are WIP patches that make use of them - not yet merged)
- lockdep micro-optimizations
- lockdep improvement: better cover IRQ contexts
- liblockdep at last. We'll continue to monitor how useful this is
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
futexes: Fix futex_hashsize initialization
arch: Re-sort some Kbuild files to hopefully help avoid some conflicts
futexes: Avoid taking the hb->lock if there's nothing to wake up
futexes: Document multiprocessor ordering guarantees
futexes: Increase hash table size for better performance
futexes: Clean up various details
arch: Introduce smp_load_acquire(), smp_store_release()
arch: Clean up asm/barrier.h implementations using asm-generic/barrier.h
arch: Move smp_mb__{before,after}_atomic_{inc,dec}.h into asm/atomic.h
locking/doc: Rename LOCK/UNLOCK to ACQUIRE/RELEASE
mutexes: Give more informative mutex warning in the !lock->owner case
powerpc: Full barrier for smp_mb__after_unlock_lock()
rcu: Apply smp_mb__after_unlock_lock() to preserve grace periods
Documentation/memory-barriers.txt: Downgrade UNLOCK+BLOCK
locking: Add an smp_mb__after_unlock_lock() for UNLOCK+BLOCK barrier
Documentation/memory-barriers.txt: Document ACCESS_ONCE()
Documentation/memory-barriers.txt: Prohibit speculative writes
Documentation/memory-barriers.txt: Add long atomic examples to memory-barriers.txt
Documentation/memory-barriers.txt: Add needed ACCESS_ONCE() calls to memory-barriers.txt
Revert "smp/cpumask: Make CONFIG_CPUMASK_OFFSTACK=y usable without debug dependency"
...
Pull core debug changes from Ingo Molnar:
"Currently there are two methods to set the panic_timeout: via
'panic=X' boot commandline option, or via /proc/sys/kernel/panic.
This tree adds a third panic_timeout configuration method:
configuration via Kconfig, via CONFIG_PANIC_TIMEOUT=X - useful to
distros that generally want their kernel defaults to come with the
.config.
CONFIG_PANIC_TIMEOUT defaults to 0, which was the previous default
value of panic_timeout.
Doing that unearthed a few arch trickeries regarding arch-special
panic_timeout values and related complications - hopefully all
resolved to the satisfaction of everyone"
* 'core-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
powerpc: Clean up panic_timeout usage
MIPS: Remove panic_timeout settings
panic: Make panic_timeout configurable
Pull hwmon updates from Guenter Roeck:
"Add support for Kaveri CPUs to k10temp driver. Add support for S12x0
to coretemp driver.
Cleanup and minor fixes in several drivers. Notable are 'Do not
return -EAGAIN for low temperatures' to coretemp and 'Re-enable
logical device mapping for NCT6791 during resume' to nct6775. Both
will be sent to -stable, but only after some time in mainline"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (k10temp) Add support for Kaveri CPUs
hwmon: (sht15) add include guard
hwmon: (max197) add include guard
hwmon: (nct6775) Re-enable logical device mapping for NCT6791 during resume
hwmon: (s3c) Trivial cleanup in hwmon-s3c.h
hwmon: (coretemp) Do not return -EAGAIN for low temperatures
hwmon: (da9052) Fix adc to voltage calculation
hwmon: (coretemp) Refine TjMax detection
hwmon: (coretemp) Add PCI device ID for CE41x0 CPUs
hwmon: (coretemp) Use PCI host bridge ID to identify CPU if necessary
hwmon: remove DEFINE_PCI_DEVICE_TABLE macro
Pull ia64 Xen removal from Tony Luck:
"Nobody has been maintaining xen in ia64 for a long time. Rip it all
out so people do not waste time making updates to broken/dead code"
* tag 'please-pull-rm_xen' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
ia64/xen: Remove Xen support for ia64
Adding picture aspect ratio for CEA modes based on CEA-861D Table 3 or
CEA-861E Table 4. This is useful for filling up the detail in AVI
infoframe.
v2: Ville's review comments incorporated
Added picture aspect ratio as part of edid_cea_modes instead of DRM_MODE
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull m68k updates from Geert Uytterhoeven:
- Zorro bus cleanups and UAPI revival
- Bootinfo cleanups and UAPI revival
- Kexec support
- Memory size reductions and bug fixes for multi-platform kernels
- Polled interrupt support for Atari EtherNAT, EtherNEC and NetUSBee
- Machine-specific random_get_entropy()
- Defconfig updates and cleanups
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k: (46 commits)
m68k/mac: Make SCC reset work more reliably
m68k/irq - Use polled IRQ flag for MFP timer cascaded interrupts
m68k: Update defconfigs for v3.13-rc1
m68k/defconfig: Enable EARLY_PRINTK
m68k/mm: kmap spelling/grammar fixes
m68k: Convert arch/m68k/kernel/traps.c to pr_*()
m68k: Convert arch/m68k/mm/fault.c to pr_*()
m68k/mm: Check for mm != NULL in do_page_fault() debug code
m68k/defconfig: Disable /sbin/hotplug fork-bomb by default
m68k/atari: Hide RTC_PORT() macro from rtc-cmos
m68k/amiga,atari: Fix specifying multiple debug= parameters
m68k/defconfig: Use ext4 for ext2/ext3 file systems
m68k: Add support to export bootinfo in procfs
m68k: Add kexec support
m68k/mac: Mark Mac IIsi ADB driver BROKEN
m68k/amiga: Provide mach_random_get_entropy()
m68k: Add infrastructure for machine-specific random_get_entropy()
m68k/atari: Call paging_init() before nf_init()
m68k: Remove superfluous inclusions of <asm/bootinfo.h>
m68k/UAPI: Use proper types (endianness/size) in <asm/bootinfo*.h>
...
Preparation for moving the early vblank IRQ logic into
radeon_get_crtc_scanoutpos().
v2: Fix radeon_drv.c compile warning (Mario)
Reviewed-by: mario.kleiner.de@gmail.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Using s64 for the timestamping constants is wasteful. Signed 32bit
integers get us a range of over +-2 seconds. Presuming that no-one
wants to a vrefresh rate less than 0.5, we can switch to using int
for the timestamping constants. We save a few bytes in drm_crtc and
avoid a bunch of 64bit math.
Reviewed-by: mario.kleiner.de@gmail.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Rather than using crtc->hwmode, just pass the relevant mode to
drm_calc_vbltimestamp_from_scanoutpos(). This removes the last hwmode
usage from core drm.
Reviewed-by: mario.kleiner.de@gmail.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
We don't really use hwmode anymore in i915, so eliminating its use
from the core code seems prudent. Just pass the appropriate mode
to drm_calc_timestamping_constants().
Reviewed-by: mario.kleiner.de@gmail.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
The stmmac driver core allows passing feature flags and callbacks via
platform data. Add a similar stmmac_of_data to pass flags and callbacks
tied to compatible strings. This allows us to extend stmmac with glue
layers for different SoCs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
