All ethertypes other than ETH_P_MPLS_UC, ETH_P_MPLS_MC and
ETH_P_ATMMPOA were already ordered numerically. This commit moves
those three ETH_P_... values into correct numerical order too.
Signed-off-by: Neil Jerram <Neil.Jerram@metaswitch.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This lets us check extensions, particularly VFIO_DMA_CC_IOMMU using
the external user interface, allowing KVM to probe IOMMU coherency.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Now that the type1 IOMMU backend can support IOMMU_CACHE, we need to
be able to test whether coherency is currently enforced. Add an
extension for this.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
We currently have a problem that we cannot support advanced features
of an IOMMU domain (ex. IOMMU_CACHE), because we have no guarantee
that those features will be supported by all of the hardware units
involved with the domain over its lifetime. For instance, the Intel
VT-d architecture does not require that all DRHDs support snoop
control. If we create a domain based on a device behind a DRHD that
does support snoop control and enable SNP support via the IOMMU_CACHE
mapping option, we cannot then add a device behind a DRHD which does
not support snoop control or we'll get reserved bit faults from the
SNP bit in the pagetables. To add to the complexity, we can't know
the properties of a domain until a device is attached.
We could pass this problem off to userspace and require that a
separate vfio container be used, but we don't know how to handle page
accounting in that case. How do we know that a page pinned in one
container is the same page as a different container and avoid double
billing the user for the page.
The solution is therefore to support multiple IOMMU domains per
container. In the majority of cases, only one domain will be required
since hardware is typically consistent within a system. However, this
provides us the ability to validate compatibility of domains and
support mixed environments where page table flags can be different
between domains.
To do this, our DMA tracking needs to change. We currently try to
coalesce user mappings into as few tracking entries as possible. The
problem then becomes that we lose granularity of user mappings. We've
never guaranteed that a user is able to unmap at a finer granularity
than the original mapping, but we must honor the granularity of the
original mapping. This coalescing code is therefore removed, allowing
only unmaps covering complete maps. The change in accounting is
fairly small here, a typical QEMU VM will start out with roughly a
dozen entries, so it's arguable if this coalescing was ever needed.
We also move IOMMU domain creation to the point where a group is
attached to the container. An interesting side-effect of this is that
we now have access to the device at the time of domain creation and
can probe the devices within the group to determine the bus_type.
This finally makes vfio_iommu_type1 completely device/bus agnostic.
In fact, each IOMMU domain can host devices on different buses managed
by different physical IOMMUs, and present a single DMA mapping
interface to the user. When a new domain is created, mappings are
replayed to bring the IOMMU pagetables up to the state of the current
container. And of course, DMA mapping and unmapping automatically
traverse all of the configured IOMMU domains.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: Varun Sethi <Varun.Sethi@freescale.com>
Implements an I2C-over-AUX I2C adapter on top of the generic drm_dp_aux
infrastructure. It extracts the retry logic from existing drivers, which
should help in porting those drivers to this new helper.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
---
Changes in v5:
- move comments partially to to header file
- keep MOT set between I2C messages
- return -EPROTO on short reads
Changes in v4:
- fix typo "bitrate" -> "bit rate"
Changes in v3:
- add back DRM_DEBUG_KMS and DRM_ERROR messages
- embed i2c_adapter within struct drm_dp_aux
- fix typo in comment
Add a helper to probe a DP link (read out the supported DPCD revision,
maximum rate, link count and capabilities) as well as power up the DP
link and configure it accordingly.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
---
Changes in v5:
- export helpers
Changes in v4:
- fix a couple of typos in comments as pointed out by Alex Deucher
Changes in v3:
- split into drm_dp_link_power_up() and drm_dp_link_configure()
- do not change sink state for DPCD versions earlier than 1.1
- sleep for 1-2 ms after setting local sink to D0 state
- read and write consecutive registers where possible
- read DPCD revision when link is probed
- remove duplicate kerneldoc
The function reads the link status (6 bytes starting at offset 0x202)
from the DPCD so that it can be conveniently passed to other DPCD
helpers.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This is a superset of the current i2c_dp_aux bus functionality and can
be used to transfer native AUX in addition to I2C-over-AUX messages.
Helpers are provided to read and write the DPCD, either blockwise or
byte-wise. Many of the existing helpers for DisplayPort take a copy of a
portion of the DPCD and operate on that, without a way to write data
back to the DPCD (e.g. for configuration of the link).
Subsequent patches will build upon this infrastructure to provide common
functionality in a generic way.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
---
Changes in v5:
- move comments partially to struct drm_dp_aux_msg in header file
- return -EPROTO on short reads in DPCD helpers
Changes in v4:
- fix a typo in a comment
Changes in v3:
- reorder drm_dp_dpcd_writeb() arguments to be more intuitive
- return number of bytes transferred in drm_dp_dpcd_write()
- factor out drm_dp_dpcd_access()
- describe error codes
This commit fixes the follwoing warning:
kernel/ksysfs.c:143:5: warning: symbol 'rcu_expedited' was not declared. Should it be static?
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
[ paulmck: Moved the declaration to include/linux/rcupdate.h to avoid
including the RCU-internal rcu.h file outside of RCU. ]
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Devices with more complex boot proceedures may occasionally apply the
register patch manual. regmap_multi_reg_write is a logical way to do so,
however the patch must be applied with cache bypass on, such that it
doesn't override any user settings. This patch adds a
regmap_multi_reg_write_bypassed function that applies a set of writes
with the bypass enabled.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There should be no need for the writes supplied to this function to be
edited by it so mark them as const.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit 93e6f119c0 ("ipc/mqueue: cleanup definition names and
locations") added global hardcoded limits to the amount of message
queues that can be created. While these limits are per-namespace,
reality is that it ends up breaking userspace applications.
Historically users have, at least in theory, been able to create up to
INT_MAX queues, and limiting it to just 1024 is way too low and dramatic
for some workloads and use cases. For instance, Madars reports:
"This update imposes bad limits on our multi-process application. As
our app uses approaches that each process opens its own set of queues
(usually something about 3-5 queues per process). In some scenarios
we might run up to 3000 processes or more (which of-course for linux
is not a problem). Thus we might need up to 9000 queues or more. All
processes run under one user."
Other affected users can be found in launchpad bug #1155695:
https://bugs.launchpad.net/ubuntu/+source/manpages/+bug/1155695
Instead of increasing this limit, revert it entirely and fallback to the
original way of dealing queue limits -- where once a user's resource
limit is reached, and all memory is used, new queues cannot be created.
Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Reported-by: Madars Vitolins <m@silodev.com>
Acked-by: Doug Ledford <dledford@redhat.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: <stable@vger.kernel.org> [3.5+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit c02cecb92e ("ARM: orion: move platform_data definitions")
moved the file to the current location but forgot to remove the pointer
to its previous location. Clean it up. While at it also change the header
file protection macros appropriately.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Commit 1ef21f6343 ("ARM: msm: move platform_data definitions")
moved the file to the current location but forgot to remove the pointer
to its previous location. Clean it up. While at it also change the header
file protection macros appropriately.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
A patch to break dependency of DaVinci NAND
driver with mach-davinci. Required for reuse
of driver on other platforms (keystone).
* tag 'davinci-for-v3.15/nand' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: aemif: get rid of davinci-nand driver dependency on aemif
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Send Channel Availability Check time as a parameter
of start_radar_detection() callback.
Get CAC time from regulatory database.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce DFS CAC time as a regd param, configured per REG_RULE and
set per channel in cfg80211. DFS CAC time is close connected with
regulatory database configuration. Instead of using hardcoded values,
get DFS CAC time form regulatory database. Pass DFS CAC time to user
mode (mainly for iw reg get, iw list, iw info). Allow setting DFS CAC
time via CRDA. Add support for internal regulatory database.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
[rewrap commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As mount() and kill_sb() is not a one-to-one match, we shoudn't get
ns refcnt unconditionally in sysfs_mount(), and instead we should
get the refcnt only when kernfs_mount() allocated a new superblock.
v2:
- Changed the name of the new argument, suggested by Tejun.
- Made the argument optional, suggested by Tejun.
v3:
- Make the new argument as second-to-last arg, suggested by Tejun.
Signed-off-by: Li Zefan <lizefan@huawei.com>
Acked-by: Tejun Heo <tj@kernel.org>
---
fs/kernfs/mount.c | 8 +++++++-
fs/sysfs/mount.c | 5 +++--
include/linux/kernfs.h | 9 +++++----
3 files changed, 15 insertions(+), 7 deletions(-)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For optimization, task_lock() is additionally used to protect
task->cgroups. The optimization is pretty dubious as either
css_set_rwsem is grabbed anyway or PF_EXITING already protects
task->cgroups. It adds only overhead and confusion at this point.
Let's drop task_[un]lock() and update comments accordingly.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Currently, process / task migration is a single operation which may
fail depending on memory pressure or the involved controllers'
->can_attach() callbacks. One problem with this approach is migration
of multiple targets. It's impossible to tell whether a given target
will be successfully migrated beforehand and cgroup core can't keep
track of enough states to roll back after intermediate failure.
This is already an issue with cgroup_transfer_tasks(). Also, we're
gonna need multiple target migration for unified hierarchy.
This patch splits migration into four stages -
cgroup_migrate_add_src(), cgroup_migrate_prepare_dst(),
cgroup_migrate() and cgroup_migrate_finish(), where
cgroup_migrate_prepare_dst() performs all the operations which may
fail due to allocation failure without actually migrating the target.
The four separate stages mean that, disregarding ->can_attach()
failures, the success or failure of multi target migration can be
determined before performing any actual migration. If preparations of
all targets succeed, the whole thing will succeed. If not, the whole
operation can fail without any side-effect.
Since the previous patch to use css_set->mg_tasks to keep track of
migration targets, the only thing which may need memory allocation
during migration is the target css_sets. cgroup_migrate_prepare()
pins all source and target css_sets and link them up. Note that this
can be performed without holding threadgroup_lock even if the target
is a process. As long as cgroup_mutex is held, no new css_set can be
put into play.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Currently, while migrating tasks from one cgroup to another,
cgroup_attach_task() builds a flex array of all target tasks;
unfortunately, this has a couple issues.
* Flex array has size limit. On 64bit, struct task_and_cgroup is
24bytes making the flex element limit around 87k. It is a high
number but not impossible to hit. This means that the current
cgroup implementation can't migrate a process with more than 87k
threads.
* Process migration involves memory allocation whose size is dependent
on the number of threads the process has. This means that cgroup
core can't guarantee success or failure of multi-process migrations
as memory allocation failure can happen in the middle. This is in
part because cgroup can't grab threadgroup locks of multiple
processes at the same time, so when there are multiple processes to
migrate, it is imposible to tell how many tasks are to be migrated
beforehand.
Note that this already affects cgroup_transfer_tasks(). cgroup
currently cannot guarantee atomic success or failure of the
operation. It may fail in the middle and after such failure cgroup
doesn't have enough information to roll back properly. It just
aborts with some tasks migrated and others not.
To resolve the situation, this patch updates the migration path to use
task->cg_list to track target tasks. The previous patch already added
css_set->mg_tasks and updated iterations in non-migration paths to
include them during task migration. This patch updates migration path
to actually make use of it.
Instead of putting onto a flex_array, each target task is moved from
its css_set->tasks list to css_set->mg_tasks and the migration path
keeps trace of all the source css_sets and the associated cgroups.
Once all source css_sets are determined, the destination css_set for
each is determined, linked to the matching source css_set and put on a
separate list.
To iterate the target tasks, migration path just needs to iterat
through either the source or target css_sets, depending on whether
migration has been committed or not, and the tasks on their ->mg_tasks
lists. cgroup_taskset is updated to contain the list_heads for source
and target css_sets and the iteration cursor. cgroup_taskset_*() are
accordingly updated to walk through css_sets and their ->mg_tasks.
This resolves the above listed issues with moderate additional
complexity.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Currently, while migrating tasks from one cgroup to another,
cgroup_attach_task() builds a flex array of all target tasks;
unfortunately, this has a couple issues.
* Flex array has size limit. On 64bit, struct task_and_cgroup is
24bytes making the flex element limit around 87k. It is a high
number but not impossible to hit. This means that the current
cgroup implementation can't migrate a process with more than 87k
threads.
* Process migration involves memory allocation whose size is dependent
on the number of threads the process has. This means that cgroup
core can't guarantee success or failure of multi-process migrations
as memory allocation failure can happen in the middle. This is in
part because cgroup can't grab threadgroup locks of multiple
processes at the same time, so when there are multiple processes to
migrate, it is imposible to tell how many tasks are to be migrated
beforehand.
Note that this already affects cgroup_transfer_tasks(). cgroup
currently cannot guarantee atomic success or failure of the
operation. It may fail in the middle and after such failure cgroup
doesn't have enough information to roll back properly. It just
aborts with some tasks migrated and others not.
To resolve the situation, we're going to use task->cg_list during
migration too. Instead of building a separate array, target tasks
will be linked into a dedicated migration list_head on the owning
css_set. Tasks on the migration list are treated the same as tasks on
the usual tasks list; however, being on a separate list allows cgroup
migration code path to keep track of the target tasks by simply
keeping the list of css_sets with tasks being migrated, making
unpredictable dynamic allocation unnecessary.
In prepartion of such migration path update, this patch introduces
css_set->mg_tasks list and updates css_set task iterations so that
they walk both css_set->tasks and ->mg_tasks. Note that ->mg_tasks
isn't used yet.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
A few code cleanups and optimizations. In addition, drop
snd_device_disconnect() that isn't used at all, and drop the return
values from snd_device_free*().
Another slight difference by this change is that now the device state
will become always SNDRV_DEV_REGISTERED no matter whether dev_register
ops is present or not. It's for better consistency. There should be
no impact for the current tree, as the state isn't checked.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Basically, the device type specifies the priority of the device to be
registered / freed, too. However, the priority value isn't well
utilized but only it's checked as a group. This results in
inconsistent register and free order (where each of them should be in
reversed direction).
This patch simplifies the device list management code by simply
inserting a list entry at creation time in an incremental order for
the priority value. Since we can just follow the link for register,
disconnect and free calls, we don't have to specify the group; so the
whole enum definitions are also simplified as well.
The visible change to outside is that the priorities of some object
types are revisited. For example, now the SNDRV_DEV_LOWLEVEL object
is registered before others (control, PCM, etc) and, in return,
released after others. Similarly, SNDRV_DEV_CODEC is in a lower
priority than SNDRV_DEV_BUS for ensuring the dependency.
Also, the unused SNDRV_DEV_TOPLEVEL, SNDRV_DEV_LOWLEVEL_PRE and
SNDRV_DEV_LOWLEVEL_NORMAL are removed as a cleanup.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just like PCM, allow hwdep to be assigned to a different parent device
than the card. It'll be used for the HD-audio codec device in the
later patches.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of calling each time device_create_file(), create the groups
of sysfs attribute files at once in a normal way. Add a new helper
function, snd_get_device(), to return the associated device object,
so that we can handle the sysfs addition locally.
Since the sysfs file addition is done differently now,
snd_add_device_sysfs_file() helper function is removed.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a lockdep_nfnl_is_held() function and a nfnl_dereference() macro for
RCU dereferences protected by a NFNL subsystem mutex.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Commit 7053aee26a "fsnotify: do not share events between notification
groups" used overflow event statically allocated in a group with the
size of the generic notification event. This causes problems because
some code looks at type specific parts of event structure and gets
confused by a random data it sees there and causes crashes.
Fix the problem by allocating overflow event with type corresponding to
the group type so code cannot get confused.
Signed-off-by: Jan Kara <jack@suse.cz>
This was used from vti and is replaced by the IPsec protocol
multiplexer hooks. It is now unused, so remove it.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
IPsec vti_rcv needs to remind the tunnel pointer to
check it later at the vti_rcv_cb callback. So add
this pointer to the IPsec common buffer, initialize
it and check it to avoid transport state matching of
a tunneled packet.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch add an IPsec protocol multiplexer. With this
it is possible to add alternative protocol handlers as
needed for IPsec virtual tunnel interfaces.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Both the pr_err and the additional kerneldoc aim to help when debugging
errors thrown from within a clock rate-change notifier callback.
Reported-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Use a resource for the hyperv mmio region instead of start/size
variables. Register the region properly so it shows up in
/proc/iomem.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Steffen Klassert says:
====================
1) Introduce skb_to_sgvec_nomark function to add further data to the sg list
without calling sg_unmark_end first. Needed to add extended sequence
number informations. From Fan Du.
2) Add IPsec extended sequence numbers support to the Authentication Header
protocol for ipv4 and ipv6. From Fan Du.
3) Make the IPsec flowcache namespace aware, from Fan Du.
4) Avoid creating temporary SA for every packet when no key manager is
registered. From Horia Geanta.
5) Support filtering of SA dumps to show only the SAs that match a
given filter. From Nicolas Dichtel.
6) Remove caching of xfrm_policy_sk_bundles. The cached socket policy bundles
are never used, instead we create a new cache entry whenever xfrm_lookup()
is called on a socket policy. Most protocols cache the used routes to the
socket, so this caching is not needed.
7) Fix a forgotten SADB_X_EXT_FILTER length check in pfkey, from Nicolas
Dichtel.
8) Cleanup error handling of xfrm_state_clone.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The name __smp_call_function_single() doesn't tell much about the
properties of this function, especially when compared to
smp_call_function_single().
The comments above the implementation are also misleading. The main
point of this function is actually not to be able to embed the csd
in an object. This is actually a requirement that result from the
purpose of this function which is to raise an IPI asynchronously.
As such it can be called with interrupts disabled. And this feature
comes at the cost of the caller who then needs to serialize the
IPIs on this csd.
Lets rename the function and enhance the comments so that they reflect
these properties.
Suggested-by: Christoph Hellwig <hch@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Jens Axboe <axboe@fb.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The main point of calling __smp_call_function_single() is to send
an IPI in a pure asynchronous way. By embedding a csd in an object,
a caller can send the IPI without waiting for a previous one to complete
as is required by smp_call_function_single() for example. As such,
sending this kind of IPI can be safe even when irqs are disabled.
This flexibility comes at the expense of the caller who then needs to
synchronize the csd lifecycle by himself and make sure that IPIs on a
single csd are serialized.
This is how __smp_call_function_single() works when wait = 0 and this
usecase is relevant.
Now there don't seem to be any usecase with wait = 1 that can't be
covered by smp_call_function_single() instead, which is safer. Lets look
at the two possible scenario:
1) The user calls __smp_call_function_single(wait = 1) on a csd embedded
in an object. It looks like a nice and convenient pattern at the first
sight because we can then retrieve the object from the IPI handler easily.
But actually it is a waste of memory space in the object since the csd
can be allocated from the stack by smp_call_function_single(wait = 1)
and the object can be passed an the IPI argument.
Besides that, embedding the csd in an object is more error prone
because the caller must take care of the serialization of the IPIs
for this csd.
2) The user calls __smp_call_function_single(wait = 1) on a csd that
is allocated on the stack. It's ok but smp_call_function_single()
can do it as well and it already takes care of the allocation on the
stack. Again it's more simple and less error prone.
Therefore, using the underscore prepend API version with wait = 1
is a bad pattern and a sign that the caller can do safer and more
simple.
There was a single user of that which has just been converted.
So lets remove this option to discourage further users.
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Jens Axboe <axboe@fb.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
rq_fifo_clear() reset the csd.list through INIT_LIST_HEAD for no clear
purpose. The csd.list doesn't need to be initialized as a list head
because it's only ever used as a list node.
Lets remove this useless initialization.
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Jens Axboe <axboe@fb.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Block layer currently abuses rq->csd.list.next for storing fifo_time.
That is a terrible hack and completely unnecessary as well. Union
achieves the same space saving in a cleaner way.
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jens Axboe <axboe@fb.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
