If the device is not initialized at least once it happens that the humidity
reading is skipped, which means the special value 0x8000 is delivered.
For omitting this case the oversampling of the humidity must be set before
the oversampling of the temperature und pressure is set as written in the
datasheet of the BME280.
Furthermore proper error detection is added in case a skipped value is read
from the device. This is done also for pressure and temperature reading.
Especially it don't make sense to compensate this value and treat it as
regular value.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since this piece of the ACPI pile is doing RAS, it is perhaps prudent if
we at least paid attention to it and the direction it takes. So add Tony
and me as reviewers.
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPI HID for Hisilicon Hip07/08 should be HISI02A1/2,
not HISI0A21/2, HISI02A1/2 was tested ok but was modified
by the stupid typo when upstream the patches (by me),
correct them to the right IDs (matching the IDs in
drivers/i2c/busses/i2c-designware-platdrv.c).
Fixes: 6e14cf361a (ACPI / APD: Add clock frequency for Hisilicon Hip07/08 I2C controller)
Reported-by: Tao Tian <tiantao6@huawei.com>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After commit f8475cef90 "x86: use common aperfmperf_khz_on_cpu() to
calculate KHz using APERF/MPERF" the scaling_cur_freq policy attribute
in sysfs only behaves as expected on x86 with APERF/MPERF registers
available when it is read from at least twice in a row. The value
returned by the first read may not be meaningful, because the
computations in there use cached values from the previous iteration
of aperfmperf_snapshot_khz() which may be stale.
To prevent that from happening, modify arch_freq_get_on_cpu() to
call aperfmperf_snapshot_khz() twice, with a short delay between
these calls, if the previous invocation of aperfmperf_snapshot_khz()
was too far back in the past (specifically, more that 1s ago).
Also, as pointed out by Doug Smythies, aperf_delta is limited now
and the multiplication of it by cpu_khz won't overflow, so simplify
the s->khz computations too.
Fixes: f8475cef90 "x86: use common aperfmperf_khz_on_cpu() to calculate KHz using APERF/MPERF"
Reported-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull perf/core improvements and fixes for 4.14 from Arnaldo Carvalho de Melo:
New features:
- Add PERF_SAMPLE_CALLCHAIN and PERF_RECORD_MMAP[2] to 'perf data' CTF
conversion, allowing CTF trace visualization tools to show callchains
and to resolve symbols (Geneviève Bastien)
Improvements:
- Use group read for event groups in 'perf stat', reducing overhead when
groups are defined in the event specification, i.e. when using {} to
enclose a list of events, asking them to be read at the same time,
e.g.: "perf stat -e '{cycles,instructions}'" (Jiri Olsa)
Fixes:
- Do not overwrite perf_sample->weight in 'perf annotate' when
processing samples, use whatever came from the kernel when
perf_event_attr.sample_type has PERF_SAMPLE_WEIGHT set or just handle
its default value, 0, when that is not set and "weight" is one of the
sort orders chosen (Arnaldo Carvalho de Melo)
- 'perf annotate --show-total-period' fixes:
- TUI should show period, not nr_samples
- Set appropriate column width for period/percent
- Fix the column header to show "Period" when when that is what
is being asked for
(Taeung Song, Arnaldo Carvalho de Melo)
- Use default sort if evlist is empty, fixing pipe mode (David Carrillo-Cisneros)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
bpf_prog_size(prog->len) is not the correct length we want to dump
back to user space. The code in bpf_prog_get_info_by_fd() uses this
to copy prog->insnsi to user space, but bpf_prog_size(prog->len) also
includes the size of struct bpf_prog itself plus program instructions
and is usually used either in context of accounting or for bpf_prog_alloc()
et al, thus we copy out of bounds in bpf_prog_get_info_by_fd()
potentially. Use the correct bpf_prog_insn_size() instead.
Fixes: 1e27097690 ("bpf: Add BPF_OBJ_GET_INFO_BY_FD")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using CONFIG_UBSAN_SANITIZE_ALL, the TCP code produces a
false-positive warning:
net/ipv4/tcp_output.c: In function 'tcp_connect':
net/ipv4/tcp_output.c:2207:40: error: array subscript is below array bounds [-Werror=array-bounds]
tp->chrono_stat[tp->chrono_type - 1] += now - tp->chrono_start;
^~
net/ipv4/tcp_output.c:2207:40: error: array subscript is below array bounds [-Werror=array-bounds]
tp->chrono_stat[tp->chrono_type - 1] += now - tp->chrono_start;
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~
I have opened a gcc bug for this, but distros have already shipped
compilers with this problem, and it's not clear yet whether there is
a way for gcc to avoid the warning. As the problem is related to the
bitfield access, this introduces a temporary variable to store the old
enum value.
I did not notice this warning earlier, since UBSAN is disabled when
building with COMPILE_TEST, and that was always turned on in both
allmodconfig and randconfig tests.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=81601
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roopa Prabhu says:
====================
ethtool: support for forward error correction mode setting on a link
Forward Error Correction (FEC) modes i.e Base-R
and Reed-Solomon modes are introduced in 25G/40G/100G standards
for providing good BER at high speeds. Various networking devices
which support 25G/40G/100G provides ability to manage supported FEC
modes and the lack of FEC encoding control and reporting today is a
source for interoperability issues for many vendors.
FEC capability as well as specific FEC mode i.e. Base-R
or RS modes can be requested or advertised through bits D44:47 of base link
codeword.
This patch set intends to provide option under ethtool to manage and
report FEC encoding settings for networking devices as per IEEE 802.3
bj, bm and by specs.
v2 :
- minor patch format fixes and typos pointed out by Andrew
- there was a pending discussion on the use of 'auto' vs
'automatic' for fec settings. I have left it as 'auto'
because in most cases today auto is used in place of
automatic to represent automatically generated values.
We use it in other networking config too. I would prefer
leaving it as auto.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Forward Error Correction (FEC) modes i.e Base-R
and Reed-Solomon modes are introduced in 25G/40G/100G standards
for providing good BER at high speeds. Various networking devices
which support 25G/40G/100G provides ability to manage supported FEC
modes and the lack of FEC encoding control and reporting today is a
source for interoperability issues for many vendors.
FEC capability as well as specific FEC mode i.e. Base-R
or RS modes can be requested or advertised through bits D44:47 of
base link codeword.
This patch set intends to provide option under ethtool to manage
and report FEC encoding settings for networking devices as per
IEEE 802.3 bj, bm and by specs.
set-fec/show-fec option(s) are designed to provide control and
report the FEC encoding on the link.
SET FEC option:
root@tor: ethtool --set-fec swp1 encoding [off | RS | BaseR | auto]
Encoding: Types of encoding
Off : Turning off any encoding
RS : enforcing RS-FEC encoding on supported speeds
BaseR : enforcing Base R encoding on supported speeds
Auto : IEEE defaults for the speed/medium combination
Here are a few examples of what we would expect if encoding=auto:
- if autoneg is on, we are expecting FEC to be negotiated as on or off
as long as protocol supports it
- if the hardware is capable of detecting the FEC encoding on it's
receiver it will reconfigure its encoder to match
- in absence of the above, the configuration would be set to IEEE
defaults.
>From our understanding , this is essentially what most hardware/driver
combinations are doing today in the absence of a way for users to
control the behavior.
SHOW FEC option:
root@tor: ethtool --show-fec swp1
FEC parameters for swp1:
Active FEC encodings: RS
Configured FEC encodings: RS | BaseR
ETHTOOL DEVNAME output modification:
ethtool devname output:
root@tor:~# ethtool swp1
Settings for swp1:
root@hpe-7712-03:~# ethtool swp18
Settings for swp18:
Supported ports: [ FIBRE ]
Supported link modes: 40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
100000baseSR4/Full
100000baseCR4/Full
100000baseLR4_ER4/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Supported FEC modes: [RS | BaseR | None | Not reported]
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: [RS | BaseR | None | Not reported]
<<<< One or more FEC modes
Speed: 100000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 106
Transceiver: internal
Auto-negotiation: off
Link detected: yes
This patch includes following changes
a) New ETHTOOL_SFECPARAM/SFECPARAM API, handled by
the new get_fecparam/set_fecparam callbacks, provides support
for configuration of forward error correction modes.
b) Link mode bits for FEC modes i.e. None (No FEC mode), RS, BaseR/FC
are defined so that users can configure these fec modes for supported
and advertising fields as part of link autonegotiation.
Signed-off-by: Vidya Sagar Ravipati <vidya.chowdary@gmail.com>
Signed-off-by: Dustin Byford <dustin@cumulusnetworks.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo says:
====================
wireless-drivers fixes for 4.13
Two fixes for for brcmfmac, the crash was reported by two people
already so it's a high priority fix.
brcmfmac
* fix a crash in skb headroom handling in v4.13-rc1
* fix a memory leak due to a merge error in v4.6
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger says:
====================
netvsc: minor fixes and optimization
This is a subset of earlier submission with a few more fixes
found during testing. The are two small optimizations, one is to
better manage the receive completion ring, and the other is removing
one unneeded level of indirection.
Will submit the improved VF support and buffer sizing in a later
patch so they get more review.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Latency improvement related to NAPI conversion.
If all packets are processed from receive ring then need
to signal host.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If setting receive buffer fails, the error unwind would cause
kernel panic because it was not correctly doing RCU and NAPI
unwind. RCU'd pointer needs to be reset to NULL, and NAPI needs
to be disabled not deleted.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Optimize how receive completion ring are managed.
* Allocate only as many slots as needed for all buffers from host
* Allocate before setting up sub channel for better error detection
* Don't need to keep copy of initial receive section message
* Precompute the watermark for when receive flushing is needed
* Replace division with conditional test
* Replace atomic per-device variable with per-channel check.
* Handle corner case where receive completion send
fails if ring buffer to host is full.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal API was passing struct hv_page_buffer **
when only simple struct hv_page_buffer * was necessary
for passing an array.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using %p to print pointer to packet meta-data doesn't give any
good info, and exposes kernel memory offsets.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This includes a bunch of fixups for issues reported by
lockdep.
* ethtool routines can assume RTNL
* send is done with RCU lock (and BH disable)
* avoid refetching internal device struct (netvsc)
instead pass it as a parameter.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump up driver version to match newer NIC firmware. Also update
nic_rx_stats (a struct common to host driver and firmware) by adding a new
field: fw_total_fwd_bytes.
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Groups of BFQ queues are represented by generic entities in BFQ. When
a queue belonging to a parent entity is deactivated, the parent entity
may need to be deactivated too, in case the deactivated queue was the
only active queue for the parent entity. This deactivation may need to
be propagated upwards if the entity belongs, in its turn, to a further
higher-level entity, and so on. In particular, the upward propagation
of deactivation stops at the first parent entity that remains active
even if one of its child entities has been deactivated.
To decide whether the last non-deactivation condition holds for a
parent entity, BFQ checks whether the field next_in_service is still
not NULL for the parent entity, after the deactivation of one of its
child entity. If it is not NULL, then there are certainly other active
entities in the parent entity, and deactivations can stop.
Unfortunately, this check misses a corner case: if in_service_entity
is not NULL, then next_in_service may happen to be NULL, although the
parent entity is evidently active. This happens if: 1) the entity
pointed by in_service_entity is the only active entity in the parent
entity, and 2) according to the definition of next_in_service, the
in_service_entity cannot be considered as next_in_service. See the
comments on the definition of next_in_service for details on this
second point.
Hitting the above corner case causes crashes.
To address this issue, this commit:
1) Extends the above check on only next_in_service to controlling both
next_in_service and in_service_entity (if any of them is not NULL,
then no further deactivation is performed)
2) Improves the (important) comments on how next_in_service is defined
and updated; in particular it fixes a few rather obscure paragraphs
Reported-by: Eric Wheeler <bfq-sched@lists.ewheeler.net>
Reported-by: Rick Yiu <rick_yiu@htc.com>
Reported-by: Tom X Nguyen <tom81094@gmail.com>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Tested-by: Eric Wheeler <bfq-sched@lists.ewheeler.net>
Tested-by: Rick Yiu <rick_yiu@htc.com>
Tested-by: Laurentiu Nicola <lnicola@dend.ro>
Tested-by: Tom X Nguyen <tom81094@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
BFQ implements hierarchical scheduling by representing each group of
queues with a generic parent entity. For each parent entity, BFQ
maintains an in_service_entity pointer: if one of the child entities
happens to be in service, in_service_entity points to it. The
resetting of these pointers happens only on queue expirations: when
the in-service queue is expired, i.e., stops to be the queue in
service, BFQ resets all in_service_entity pointers along the
parent-entity path from this queue to the root entity.
Functions handling the scheduling of entities assume, naturally, that
in-service entities are active, i.e., have pending I/O requests (or,
as a special case, even if they have no pending requests, they are
expected to receive a new request very soon, with the scheduler idling
the storage device while waiting for such an event). Unfortunately,
the above resetting scheme of the in_service_entity pointers may cause
this assumption to be violated. For example, the in-service queue may
happen to remain without requests because of a request merge. In this
case the queue does become idle, and all related data structures are
updated accordingly. But in_service_entity still points to the queue
in the parent entity. This inconsistency may even propagate to
higher-level parent entities, if they happen to become idle as well,
as a consequence of the leaf queue becoming idle. For this queue and
parent entities, scheduling functions have an undefined behaviour,
and, as reported, may easily lead to kernel crashes or hangs.
This commit addresses this issue by simply resetting the
in_service_entity field also when it is detected to point to an entity
becoming idle (regardless of why the entity becomes idle).
Reported-by: Laurentiu Nicola <lnicola@dend.ro>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Tested-by: Laurentiu Nicola <lnicola@dend.ro>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
err in bpf_prog_get_info_by_fd() still holds 0 at that time from prior
check_uarg_tail_zero() check. Explicitly return -EFAULT instead, so
user space can be notified of buggy behavior.
Fixes: 1e27097690 ("bpf: Add BPF_OBJ_GET_INFO_BY_FD")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an early demuxed packet reaches __udp6_lib_lookup_skb(), the
sk reference is retrieved and used, but the relevant reference
count is leaked and the socket destructor is never called.
Beyond leaking the sk memory, if there are pending UDP packets
in the receive queue, even the related accounted memory is leaked.
In the long run, this will cause persistent forward allocation errors
and no UDP skbs (both ipv4 and ipv6) will be able to reach the
user-space.
Fix this by explicitly accessing the early demux reference before
the lookup, and properly decreasing the socket reference count
after usage.
Also drop the skb_steal_sock() in __udp6_lib_lookup_skb(), and
the now obsoleted comment about "socket cache".
The newly added code is derived from the current ipv4 code for the
similar path.
v1 -> v2:
fixed the __udp6_lib_rcv() return code for resubmission,
as suggested by Eric
Reported-by: Sam Edwards <CFSworks@gmail.com>
Reported-by: Marc Haber <mh+netdev@zugschlus.de>
Fixes: 5425077d73 ("net: ipv6: Add early demux handler for UDP unicast")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_en depends on MAY_USE_DEVLINK; this is used to force bnxt_en
to be =m when DEVLINK is =m.
Now, bnxt_re selects bnxt_en. Unless bnxt_re also explicitly calls
out dependency on MAY_USE_DEVLINK, Kconfig does not force bnxt_re
to be =m when DEVLINK is =m, causing the following error:
drivers/net/ethernet/broadcom/bnxt/bnxt_vfr.o: In function
`bnxt_dl_register':
bnxt_vfr.c:(.text+0x1440): undefined reference to `devlink_alloc'
bnxt_vfr.c:(.text+0x14c0): undefined reference to `devlink_register'
bnxt_vfr.c:(.text+0x14e0): undefined reference to `devlink_free'
drivers/net/ethernet/broadcom/bnxt/bnxt_vfr.o: In function
`bnxt_dl_unregister':
bnxt_vfr.c:(.text+0x1534): undefined reference to `devlink_unregister'
bnxt_vfr.c:(.text+0x153c): undefined reference to `devlink_free'
Fix this by adding MAY_USE_DEVLINK dependency in bnxt_re.
Fixes: 4ab0c6a8ff ("bnxt_en: add support to enable VF-representors")
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For SGMII/RGMII/QSGMII interfaces when physical link goes down
while traffic is high is resulting in underflow condition being set
on that specific BGX's LMAC. Which assets a backpresure and VNIC stops
transmitting packets.
This is due to BGX being disabled in link status change callback while
packet is in transit. This patch fixes this issue by not disabling BGX
but instead just disables packet Rx and Tx.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 809ecb9bca. Since it
was reported to break vhost_net. We want to cache used event and use
it to check for notification. The assumption was that guest won't move
the event idx back, but this could happen in fact when 16 bit index
wraps around after 64K entries.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apparently through one of my revisions of the initial patches
series I lost the devmap test. We can add more testing later but
for now lets fix the simple one we have.
Fixes: 546ac1ffb7 "bpf: add devmap, a map for storing net device references"
Reported-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
SZ Lin says:
====================
net: moxa: Fix style issues
This patch set fixs the WARNINGs found by the checkpatch.pl tool
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes all checkpatch occurences of
"CHECK: spaces preferred around that '{+,-}' (ctx:VxV)"
in moxart_ether code.
Signed-off-by: SZ Lin <sz.lin@moxa.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No space is necessary after a cast
This warning is found using checkpatch.pl
Signed-off-by: SZ Lin <sz.lin@moxa.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed coding style for null comparisons in moxart_ether driver
to be more consistent with the rest of the kernel coding style
Signed-off-by: SZ Lin <sz.lin@moxa.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use 'unsigned int' instead of 'unsigned'
This warning is found using checkpatch.pl
Signed-off-by: SZ Lin <sz.lin@moxa.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary braces from single-line if statement
This warning is found using checkpatch.pl
Signed-off-by: SZ Lin <sz.lin@moxa.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Blend/ROP Sub Unit (BRS) is a stripped-down version of the BRU found
in several VSP2 instances. Compared to a regular BRU, it supports two
inputs only, and thus has no ROP unit.
Add support for the BRS by modelling it as a new entity type, but reuse
the vsp1_bru object underneath. Chaining the BRU and BRS entities seems
to be supported by the hardware but isn't implemented yet as it isn't
the primary use case for the BRS.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In the H3 ES2.0 SoC the VSP2-DL instance has two connections to DU
channels that need to be configured independently. Extend the VSP-DU API
with a pipeline index to identify which pipeline the caller wants to
operate on.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When the VSP1 is used in a DRM pipeline the driver doesn't register the
media device. Links between entities are not exposed to userspace, but
are still used internally for the sole purpose of setting up internal
source to sink pointers through the link setup handler.
Instead of going through this complex procedure, remove link creation
and set the sink pointers directly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The internal VSP entity source and sink pointers are stored as
media_entity pointers, which are then cast to a vsp1_entity. As all
sources and sinks are vsp1_entity instances, we can store the
vsp1_entity pointers directly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The sink pointer is used to configure routing inside the VSP, and as
such must point to the next VSP entity in the pipeline. The WPF being a
pipeline terminal sink, its output route can't be configured. The
routing configuration code already handles this correctly without
referring to the sink pointer, which thus doesn't need to be set.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
