Add support for GRO (generic receive offload) for aQuantia Atlantic driver.
This results in a perfomance improvement when GRO is enabled.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a regulator requests a deferred probe, the power domain gets
initialized twice. This leads to a list double add (without
list debugging the kernel hangs due to the double add later):
WARNING: CPU: 0 PID: 19 at lib/list_debug.c:31 __list_add_valid+0xbc/0xc4
list_add double add: new=c1229754, prev=c12383b4, next=c1229754.
Initialize the power domain after we get the regulator. Also do
not print an error in case the regulator defers probing.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Fixes: 03aa12629f ("soc: imx: Add GPCv2 power gating driver")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Tested-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The CX9020 differs from i.MX53 Quick Start Board by:
- use uart2 instead of uart1
- DVI-D connector instead of VGA
- no audio
- no SATA connector
- CCAT FPGA connected to emi
- enable rtc
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
UART2 on EIM_D26 - EIM_D29 pins supports interchanging RXD/TXD pins
and RTS/CTS pins.
One board using these alternate settings is Beckhoff CX9020. Add the
alternative configuration here, to make it available to others, too.
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX53 has an integrated secure real time clock. Add it to the dtsi.
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
aliases node is identical for all boards, thus move it
to the common file ls208xa.dtsi.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
"""
This PR contains both core and drivers fixes for 4.13.
Core fixes:
- Fix data interface setup for ONFI NANDs that do not support the SET
FEATURES command
- Fix a kernel doc header
- Fix potential integer overflow when retrieving timing information
from the parameter page
- Fix wrong OOB layout for small page NANDs
Driver fixes:
- Fix potential division-by-zero bug
- Fix backward compat with old atmel-nand DT bindings
- Fix ->setup_data_interface() in the atmel NAND driver
"""
Add a devicetree entry for the Random Number Generator Version B (RNGB).
The driver for RNGC supports version B as well.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Modify the ACPI system sleep support setup code to select
suspend-to-idle as the default system sleep state if
(1) the ACPI_FADT_LOW_POWER_S0 flag is set in the FADT and
(2) the Low Power Idle S0 _DSM interface has been discovered and
(3) the default sleep state was not selected from the kernel command
line.
The main motivation for this change is that systems where the (1) and
(2) conditions are met typically ship with OSes that don't exercise
the S3 path in the platform firmware which remains untested and turns
out to be non-functional at least in some cases.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
Pull clk fixes from Stephen Boyd:
"A handful of critical fixes for changes introduce this merge window.
- The TI sci_clk_get() API was pretty broken and nobody noticed.
- There were some CPUfreq crashes on C.H.I.P devices because we
failed to propagate rates up the clk tree.
- Also, the Intel Atom PMC clk driver needs to mark a clk critical if
the firmware has it enabled already so that audio doesn't get
killed on Baytrail.
- Gemini devices have a dead serial console because the reset control
usage in the serial driver assume one method of reset that gemini
doesn't support (this will be fixed in the next version in the
reset framework so this is the small fix for -rc series).
- Finally we have two rate calculation fixes, one for Exynos and one
for Meson SoCs, that fix rate inconsistencies"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: keystone: sci-clk: Fix sci_clk_get
clk: meson: mpll: fix mpll0 fractional part ignored
clk: samsung: exynos5420: The EPLL rate table corrections
clk: sunxi-ng: sun5i: Add clk_set_rate_parent to the CPU clock
clk: x86: Do not gate clocks enabled by the firmware
clk: gemini: Fix reset regression
We really must check with #if __BYTE_ORDER == XYZ instead of
just presence of #ifdef __LITTLE_ENDIAN. I noticed that when
actually running this on big endian machine, the latter test
resolves to true for user space, same for #ifdef __BIG_ENDIAN.
E.g., looking at endian.h from libc, both are also defined
there, so we really must test this against __BYTE_ORDER instead
for proper insns selection. For the kernel, such checks are
fine though e.g. see 13da9e200f ("Revert "endian: #define
__BYTE_ORDER"") and 415586c9e6 ("UAPI: fix endianness conditionals
in M32R's asm/stat.h") for some more context, but not for
user space. Lets also make sure to properly include endian.h.
After that, suite passes for me:
./test_verifier: ELF 64-bit MSB executable, [...]
Linux foo 4.13.0-rc3+ #4 SMP Fri Aug 4 06:59:30 EDT 2017 s390x s390x s390x GNU/Linux
Before fix: Summary: 505 PASSED, 11 FAILED
After fix: Summary: 516 PASSED, 0 FAILED
Fixes: 18f3d6be6b ("selftests/bpf: Add test cases to test narrower ctx field loads")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong <yhs@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull KVM fixes from Radim Krčmář:
"ARM:
- Yet another race with VM destruction plugged
- A set of small vgic fixes
x86:
- Preserve pending INIT
- RCU fixes in paravirtual async pf, VM teardown, and VMXOFF
emulation
- nVMX interrupt injection and dirty tracking fixes
- initialize to make UBSAN happy"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: arm/arm64: vgic: Use READ_ONCE fo cmpxchg
KVM: nVMX: Fix interrupt window request with "Acknowledge interrupt on exit"
KVM: nVMX: mark vmcs12 pages dirty on L2 exit
kvm: nVMX: don't flush VMCS12 during VMXOFF or VCPU teardown
KVM: nVMX: do not pin the VMCS12
KVM: avoid using rcu_dereference_protected
KVM: X86: init irq->level in kvm_pv_kick_cpu_op
KVM: X86: Fix loss of pending INIT due to race
KVM: async_pf: make rcu irq exit if not triggered from idle task
KVM: nVMX: fixes to nested virt interrupt injection
KVM: nVMX: do not fill vm_exit_intr_error_code in prepare_vmcs12
KVM: arm/arm64: Handle hva aging while destroying the vm
KVM: arm/arm64: PMU: Fix overflow interrupt injection
KVM: arm/arm64: Fix bug in advertising KVM_CAP_MSI_DEVID capability
Pull x86 fix from Thomas Gleixner:
"The recent irq core changes unearthed API abuse in the HPET code,
which manifested itself in a suspend/resume regression.
The fix replaces the cruft with the proper function calls and cures
the regression"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/hpet: Cure interface abuse in the resume path
Pull timer fix from Thomas Gleixner:
"A single fix for a multiplication overflow in the timer code on 32bit
systems"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timers: Fix overflow in get_next_timer_interrupt
Pull ARM SoC fixes from Arnd Bergmann:
"This comes a bit later than I planned, and as a consequence is a
larger than it should be.
Most of the changes are devicetree fixes, across lots of platforms:
Renesas, Samsung Exynos, Marvell EBU, TI OMAP, Rockchips, Amlogic
Meson, Sigma Desings Tango, Allwinner SUNxi and TI Davinci.
Also across many platforms, I applied an older series of simple
randconfig build fixes. This includes making the CONFIG_MTD_XIP option
compile again, which had been broken for many years and probably has
not been missed, but it felt wrong to just remove it completely.
The only other changes are:
- We enable HWSPINLOCK in defconfig to get some Qualcomm boards to
work out of the box.
- A few regression fixes for Texas Instruments OMAP2+.
- A boot regression fix for the Renesas regulator quirk.
- A suspend/resume fix for Uniphier SoCs, fixing the resume of the
system bus"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
ARM: dts: tango4: Request RGMII RX and TX clock delays
bus: uniphier-system-bus: set up registers when resuming
ARM64: dts: marvell: armada-37xx: Fix the number of GPIO on south bridge
ARM: shmobile: rcar-gen2: Fix deadlock in regulator quirk
arm64: defconfig: enable missing HWSPINLOCK
ARM: pxa: select both FB and FB_W100 for eseries
ARM: ixp4xx: fix ioport_unmap definition
ARM: ep93xx: use ARM_PATCH_PHYS_VIRT correctly
ARM: mmp: mark usb_dma_mask as __maybe_unused
ARM: omap2: mark unused functions as __maybe_unused
ARM: omap1: avoid unused variable warning
ARM: sirf: mark sirfsoc_init_late as __maybe_unused
ARM: ixp4xx: use normal prototype for {read,write}s{b,w,l}
ARM: omap1/ams-delta: warn about failed regulator enable
ARM: rpc: rename RAM_SIZE macro
ARM: w90x900: normalize clk API
ARM: ep93xx: normalize clk API
ARM: dts: sun8i: a83t: Switch to CCU device tree binding macros
arm64: allwinner: sun50i-a64: Correct emac register size
ARM: dts: sunxi: h3/h5: Correct emac register size
...
According to the commit that implemented per-inode DAX flag:
commit 58f88ca2df ("xfs: introduce per-inode DAX enablement")
the flag is supposed to act as "inherit flag".
Currently this only works in the situations where parent directory
already has a flag in di_flags set, otherwise inheritance does not
work. This is because setting the XFS_DIFLAG2_DAX flag is done in a
wrong branch designated for di_flags, not di_flags2.
Fix this by moving the code to branch designated for setting di_flags2,
which does test for flags in di_flags2.
Fixes: 58f88ca2df ("xfs: introduce per-inode DAX enablement")
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The bio describing discard operation is allocated by
__blkdev_issue_discard() which returns us a reference to it. That
reference is never released and thus we leak this bio. Drop the bio
reference once it completes in xlog_discard_endio().
CC: stable@vger.kernel.org
Fixes: 4560e78f40
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The newly introduced ahci_platform_shutdown() method is called during
system shutdown to disable host controller DMA and interrupts in order
to avoid potentially corrupting or otherwise interfering with a new
kernel being started with kexec.
Signed-off-by: Nate Watterson <nwatters@codeaurora.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Two new tests STACK_GUARD_PAGE_LEADING and STACK_GUARD_PAGE_TRAILING
attempt to read the byte before and after, respectively, of the current
stack frame, which should fault.
Signed-off-by: Kees Cook <keescook@chromium.org>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work with
const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Pull arm64 fixes from Will Deacon:
"Here are some more arm64 fixes for 4.13. The main one is the PTE race
with the hardware walker, but there are a couple of other things too.
- Report correct timer frequency to userspace when trapping
CNTFRQ_EL0
- Fix race with hardware page table updates when updating access
flags
- Silence clang overflow warning in VA_START and PAGE_OFFSET
calculations"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: avoid overflow in VA_START and PAGE_OFFSET
arm64: Fix potential race with hardware DBM in ptep_set_access_flags()
arm64: Use arch_timer_get_rate when trapping CNTFRQ_EL0
The hns_roce_v1_create_lp_qp() returns NULL on error, not error pointers.
Fixes: bfcc681bd0 ("IB/hns: Fix the bug when free mr")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Even the driver doesn't do anything with the clk source for SGMII
ports it needs to be enabled by doing a devm_clk_get(), if there is
a clk source in DT.
Fixes: 0db01097ca ('xgene: Don't fail probe, if there is no clk resource for SGMII interfaces')
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Tested-by: Laura Abbott <labbott@redhat.com>
Acked-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The extended address vector is the highest bit in be32 variable,
but it was compared with the lowest. This patch fixes the endianness
of that check and removes already declared define.
Fixes: 17d2f88f92 ("IB/mlx5: Add ODP atomics support")
Reviewed-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Uverbs device should be cleaned up only when there is no
potential usage of.
As part of ib_uverbs_remove_one which might be triggered upon reset flow
the device reference count is decreased as expected and leave the final
cleanup to the FDs that were opened.
Current code increases reference count upon opening a new command FD and
decreases it upon closing the file. The event FD is opened internally
and rely on the command FD by taking on it a reference count.
In case that the command FD was closed and just later the event FD we
may ensure that the device resources as of srcu are still alive as they
are still in use.
Fixing the above by moving the reference count decreasing to the place
where the command FD is really freed instead of doing that when it was
just closed.
fixes: 036b106357 ("IB/uverbs: Enable device removal when there are active user space applications")
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
initialize to zero the response structure to prevent
the leakage of "resp.reserved" field.
drivers/infiniband/core/uverbs_cmd.c:1178 ib_uverbs_resize_cq() warn:
check that 'resp.reserved' doesn't leak information
Fixes: 33b9b3ee97 ("IB: Add userspace support for resizing CQs")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Currently while resolving IP address to MAC address single delayed work
is used for resolving multiple such resolve requests. This singled work
is essentially performs two tasks.
(a) any retry needed to resolve and
(b) it executes the callback function for all completed requests
While work is executing callbacks, any new work scheduled on for this
workqueue is lost because workqueue has completed looking at all pending
requests and now looking at callbacks, but work is still under
execution. Any further retry to look at pending requests in
process_req() after executing callbacks would lead to similar race
condition (may be reduce the probably further but doesn't eliminate it).
Retrying to enqueue work that from queue_req() context is not something
rest of the kernel modules have followed.
Therefore fix in this patch utilizes kernel facility to enqueue multiple
work items to a workqueue. This ensures that no such requests
gets lost in synchronization. Request list is still maintained so that
rdma_cancel_addr() can unlink the request and get the completion with
error sooner. Neighbour update event handling continues to be handled in
same way as before.
Additionally process_req() work entry cancels any pending work for a
request that gets completed while processing those requests.
Originally ib_addr was ST workqueue, but it became MT work queue with
patch of [1]. This patch again makes it similar to ST so that
neighbour update events handler work item doesn't race with
other work items.
In one such below trace, (though on 4.5 based kernel) it can be seen
that process_req() never executed the callback, which is likely for an
event that was schedule by queue_req() when previous callback was
getting executed by workqueue.
[<ffffffff816b0dde>] schedule+0x3e/0x90
[<ffffffff816b3c45>] schedule_timeout+0x1b5/0x210
[<ffffffff81618c37>] ? ip_route_output_flow+0x27/0x70
[<ffffffffa027f9c9>] ? addr_resolve+0x149/0x1b0 [ib_addr]
[<ffffffff816b228f>] wait_for_completion+0x10f/0x170
[<ffffffff810b6140>] ? try_to_wake_up+0x210/0x210
[<ffffffffa027f220>] ? rdma_copy_addr+0xa0/0xa0 [ib_addr]
[<ffffffffa0280120>] rdma_addr_find_l2_eth_by_grh+0x1d0/0x278 [ib_addr]
[<ffffffff81321297>] ? sub_alloc+0x77/0x1c0
[<ffffffffa02943b7>] ib_init_ah_from_wc+0x3a7/0x5a0 [ib_core]
[<ffffffffa0457aba>] cm_req_handler+0xea/0x580 [ib_cm]
[<ffffffff81015982>] ? __switch_to+0x212/0x5e0
[<ffffffffa04582fd>] cm_work_handler+0x6d/0x150 [ib_cm]
[<ffffffff810a14c1>] process_one_work+0x151/0x4b0
[<ffffffff810a1940>] worker_thread+0x120/0x480
[<ffffffff816b074b>] ? __schedule+0x30b/0x890
[<ffffffff810a1820>] ? process_one_work+0x4b0/0x4b0
[<ffffffff810a1820>] ? process_one_work+0x4b0/0x4b0
[<ffffffff810a6b1e>] kthread+0xce/0xf0
[<ffffffff810a6a50>] ? kthread_freezable_should_stop+0x70/0x70
[<ffffffff816b53a2>] ret_from_fork+0x42/0x70
[<ffffffff810a6a50>] ? kthread_freezable_should_stop+0x70/0x70
INFO: task kworker/u144:1:156520 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this
message.
kworker/u144:1 D ffff883ffe1d7600 0 156520 2 0x00000080
Workqueue: ib_addr process_req [ib_addr]
ffff883f446fbbd8 0000000000000046 ffff881f95280000 ffff881ff24de200
ffff883f66120000 ffff883f446f8008 ffff881f95280000 ffff883f6f9208c4
ffff883f6f9208c8 00000000ffffffff ffff883f446fbbf8 ffffffff816b0dde
[1] http://lkml.iu.edu/hypermail/linux/kernel/1608.1/05834.html
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Inexplicably, commit f381bf6d82 ("MIPS: Add support for eBPF JIT.")
lost a file somewhere on its path to Linus' tree. Add back the
missing ebpf_jit.c so that we can build with CONFIG_BPF_JIT selected.
This version of ebpf_jit.c is identical to the original except for two
minor change need to resolve conflicts with changes merged from the
BPF branch:
A) Set prog->jited_len = image_size;
B) Use BPF_TAIL_CALL instead of BPF_CALL | BPF_X
Fixes: f381bf6d82 ("MIPS: Add support for eBPF JIT.")
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
net: sched: summer cleanup part 1, mainly in exts area
This patchset is one of the couple cleanup patchsets I have in queue.
The motivation aside the obvious need to "make things nicer" is also
to prepare for shared filter blocks introduction. That requires tp->q
removal, and therefore removal of all tp->q users.
Patch 1 is just some small thing I spotted on the way
Patch 2 removes one user of tp->q, namely tcf_em_tree_change
Patches 3-8 do preparations for exts->nr_actions removal
Patches 9-10 do simple renames of functions in cls*
Patches 11-19 remove unnecessary calls of tcf_exts_change helper
The last patch changes tcf_exts_change to don't take lock
Tested by tools/testing/selftests/tc-testing
v1->v2:
- removed conversion of action array to list as noted by Cong
- added the past patch instead
- small rebases of patches 11-19
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
tcf_exts_change is always called on newly created exts, which are not used
on fastpath. Therefore, simple struct copy is enough.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the n struct was allocated right before u32_set_parms call,
no need to use tcf_exts_change to do atomic change, and we can just
fill-up the unused exts struct directly by tcf_exts_validate.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the f struct was allocated right before route4_set_parms call,
no need to use tcf_exts_change to do atomic change, and we can just
fill-up the unused exts struct directly by tcf_exts_validate.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the fnew struct just was allocated, so no need to use tcf_exts_change
to do atomic change, and we can just fill-up the unused exts struct
directly by tcf_exts_validate.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the new struct just was allocated, so no need to use tcf_exts_change
to do atomic change, and we can just fill-up the unused exts struct
directly by tcf_exts_validate.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the prog struct was allocated right before cls_bpf_set_parms call,
no need to use tcf_exts_change to do atomic change, and we can just
fill-up the unused exts struct directly by tcf_exts_validate.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the f struct was allocated right before basic_set_parms call, no need
to use tcf_exts_change to do atomic change, and we can just fill-up
the unused exts struct directly by tcf_exts_validate.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the head struct was allocated right before mall_set_parms call,
no need to use tcf_exts_change to do atomic change, and we can just
fill-up the unused exts struct directly by tcf_exts_validate.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the f struct was allocated right before fw_set_parms call, no need
to use tcf_exts_change to do atomic change, and we can just fill-up
the unused exts struct directly by tcf_exts_validate.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the f struct was allocated right before fl_set_parms call, no need
to use tcf_exts_change to do atomic change, and we can just fill-up
the unused exts struct directly by tcf_exts_validate.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the function name is misleading since it is not changing
anything, name it similarly to other cls.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The name cls_bpf_modify_existing is highly misleading, as it indeed does
not modify anything existing. It does not modify at all.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
For check in tcf_exts_dump use tcf_exts_has_actions helper instead
of exts->nr_actions for checking if there are any actions present.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leave it to tcf_action_exec to return TC_ACT_OK in case there is no
action present.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These two helpers are doing the same as tcf_exts_has_actions, so remove
them and use tcf_exts_has_actions instead.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the tcf_exts_has_actions helper instead or directly testing
exts->nr_actions in tcf_exts_exec.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
