Daniel Borkmann says:
====================
bpf: Minor fix in bpf_convert_ctx_access
First one was found while trying to compile the kernel
with !CONFIG_NET_RX_BUSY_POLL.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_NET_SCHED or CONFIG_NET_RX_BUSY_POLL is /not/ set and
we try a narrow __sk_buff load of tc_index or napi_id, respectively,
then verifier rightfully complains that it's misconfigured, because
we need to set target_size in each of the two cases. The rewrite
for the ctx access is just a dummy op, but needs to pass, so fix
this up.
Fixes: f96da09473 ("bpf: simplify narrower ctx access")
Reported-by: Shubham Bansal <illusionist.neo@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
MIN_NAPI_ID is used in various places outside of
CONFIG_NET_RX_BUSY_POLL wrapping, so when it's not set
we run into build errors such as:
net/core/dev.c: In function 'dev_get_by_napi_id':
net/core/dev.c:886:16: error: ‘MIN_NAPI_ID’ undeclared (first use in this function)
if (napi_id < MIN_NAPI_ID)
^~~~~~~~~~~
Thus, have MIN_NAPI_ID always defined to fix these errors.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make these structures const as they only stored in the profile field of
a mlxsw_driver structure, which is of type const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If mISDN_FsmNew() fails to allocate memory for jumpmatrix
then null pointer dereference will occur on any write to
jumpmatrix.
The patch adds check on successful allocation and
corresponding error handling.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
OVS_NLERR already adds a newline so these just add blank
lines to the logging.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Joe Stringer <joe@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware expects a MAC_REPR control message when a MAC representor
is created. The driver should expect a PORTMOD message to follow which
will provide the link states of the physical port associated with the MAC
representor.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Flower app may receive a request to update the MTU of a representor
netdev upon receipt of a control message from the firmware. This requires
the RTNL lock which needs to be taken outside of the packet processing
path.
As a handling of this correctly seems a little to invasive for a fix simply
skip setting the MTU for now.
Relevant backtrace:
[ 1496.288489] BUG: scheduling while atomic: kworker/0:3/373/0x00000100
[ 1496.294911] dca syscopyarea sysfillrect sysimgblt fb_sys_fops ptp drm mxm_wmi ahci pps_core libahci i2c_algo_bit wmi [last unloaded: nfp]
[ 1496.294918] CPU: 0 PID: 373 Comm: kworker/0:3 Tainted: G OE 4.13.0-rc3+ #3
[ 1496.294919] Hardware name: Supermicro X10DRi/X10DRi, BIOS 2.0 12/28/2015
[ 1496.294923] Workqueue: events work_for_cpu_fn
[ 1496.294924] Call Trace:
[ 1496.294927] <IRQ>
[ 1496.294931] dump_stack+0x63/0x82
[ 1496.294935] __schedule_bug+0x54/0x70
[ 1496.294937] __schedule+0x62f/0x890
[ 1496.294941] ? intel_unmap_sg+0x90/0x90
[ 1496.294942] schedule+0x36/0x80
[ 1496.294943] schedule_preempt_disabled+0xe/0x10
[ 1496.294945] __mutex_lock.isra.2+0x445/0x4a0
[ 1496.294947] ? device_is_rmrr_locked+0x12/0x50
[ 1496.294950] ? kfree+0x162/0x170
[ 1496.294952] ? device_is_rmrr_locked+0x12/0x50
[ 1496.294953] ? iommu_should_identity_map+0x50/0xe0
[ 1496.294954] __mutex_lock_slowpath+0x13/0x20
[ 1496.294955] ? iommu_no_mapping+0x48/0xd0
[ 1496.294956] ? __mutex_lock_slowpath+0x13/0x20
[ 1496.294957] mutex_lock+0x2f/0x40
[ 1496.294960] rtnl_lock+0x15/0x20
[ 1496.294979] nfp_flower_cmsg_rx+0xc8/0x150 [nfp]
[ 1496.294986] nfp_ctrl_poll+0x286/0x350 [nfp]
[ 1496.294989] tasklet_action+0xf6/0x110
[ 1496.294992] __do_softirq+0xed/0x278
[ 1496.294993] irq_exit+0xb6/0xc0
[ 1496.294994] do_IRQ+0x4f/0xd0
[ 1496.294996] common_interrupt+0x89/0x89
Fixes: 948faa46c0 ("nfp: add support for control messages for flower app")
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use the dma_*() interfaces rather than the pci_*() interfaces.
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver does not check if mapping dma memory succeed.
The patch adds the checks and failure handling.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Attempts to connect to a local address with a socket bound
to a device with the local address hangs if there is no listener:
$ ip addr sh dev eth1
3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
link/ether 02:e0:f9:1c:00:37 brd ff:ff:ff:ff:ff:ff
inet 10.100.1.4/24 scope global eth1
valid_lft forever preferred_lft forever
inet6 2001:db8:1::4/120 scope global
valid_lft forever preferred_lft forever
inet6 fe80::e0:f9ff:fe1c:37/64 scope link
valid_lft forever preferred_lft forever
$ vrf-test -I eth1 -r 10.100.1.4
<hangs when there is no server>
(don't let the command name fool you; vrf-test works without vrfs.)
The problem is that the original intended device, eth1 in this case, is
lost when the tcp reset is sent, so the socket lookup does not find a
match for the reset and the connect attempt hangs. Fix by adjusting
orig_oif for local traffic to the device from the fib lookup result.
With this patch you get the more user friendly:
$ vrf-test -I eth1 -r 10.100.1.4
connect failed: 111: Connection refused
orig_oif is saved to the newly created rtable as rt_iif and when set
it is used as the dif for socket lookups. It is set based on flowi4_oif
passed in to ip_route_output_key_hash_rcu and will be set to either
the loopback device, an l3mdev device, nothing (flowi4_oif = 0 which
is the case in the example above) or a netdev index depending on the
lookup path. In each case, resetting orig_oif to the device in the fib
result for the RTN_LOCAL case allows the actual device to be preserved
as the skb tx and rx is done over the loopback or VRF device.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the function stmmac_mdio_register() is only used by
stmmac_dvr_probe() from stmmac_main.c, in order to register the MDIO bus
and probe information about the PHY. As this function is called before
calling register_netdev(), all messages logged from stmmac_mdio_register
are prefixed by "(unnamed net_device)". The goal of netdev_info or
netdev_err is to dump useful infos about a net_device, when this data
structure is partially initialized, there is no point for using these
functions.
This commit fixes the issue by replacing all netdev_*() by the
corresponding dev_*() function for logging. The last netdev_info is
replaced by phy_attached_info(), as a valid phydev can be used at this
point.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implemented workarounds for the following dTSEC Erratum:
A002, A004, A0012, A0014, A004839 on several operations
that involve MAC CFG register changes: adjust link,
rx pause frames, modify MAC address.
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Acked-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These were copy and paste bugs, but I believe they are harmless.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function has a copy and paste bug so it accidentally calls the add
function instead of the delete function.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Wu says:
====================
rockchip: Add the integrated PHY support
The rk3228 and rk3328 support integrated PHY inside, let's enable
it to work. And the integrated PHY need to do some special setting,
so register the rockchip integrated PHY driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable the gmac2phy, make the gmac2phy work on
the rk3328-evb board.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The gmac2phy controller of rk3328 is connected to integrated PHY
directly inside, add the node for the integrated PHY support.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables the integrated PHY for rk3228 evb board
by default.
To use the external 1000M PHY on evb board, need to make
some switch of evb board to be on.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two mac controllers in the rk3328, the one connects
to external PHY, and the other one connects to integrated PHY.
Like the mac of external PHY, the integrated PHY's mac also
needs to configure the related mac registers at GRF.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is only one mac controller in rk3228, which could connect to
external PHY or integrated PHY, use the grf_com_mux bit15 to route
external/integrated PHY.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make integrated PHY work, need to configure the PHY clock,
PHY cru reset and related registers.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the documentation for integrated PHY. A boolean property indicates
the PHY is integrated into the same physical package as the Ethernet
MAC. If needed, muxers should be configured to ensure the integrated
PHY is used. The absence of this property indicates the muxers should
be configured so that the external PHY is used.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace init_timer_deferrable with setup_deferrable_timer to simplify
the source code.
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frequency can be adjusted in DT it make sense to
print current used value on driver init.
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Polling 14 mdio devices on single mdio bus eats 30% of 1Ghz cpu time
due to busy loop in wait(). Add small delay to relax cpu.
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch c4adfc822b ("bonding: make speed, duplex setting consistent
with link state") puts the link state to down if
bond_update_speed_duplex() cannot retrieve speed and duplex settings.
Assumably the patch was written with 802.3ad mode in mind which relies
on link speed/duplex settings. For other modes like active-backup these
settings are not required. Thus, only for these other modes, this patch
reintroduces support for slaves that do not support reporting speed or
duplex such as wireless devices. This fixes the regression reported in
bug 196547 (https://bugzilla.kernel.org/show_bug.cgi?id=196547).
Fixes: c4adfc822b ("bonding: make speed, duplex setting consistent
with link state")
Signed-off-by: Andreas Born <futur.andy@googlemail.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger says:
====================
netvsc: minor fixes and improvements
These are non-critical bug fixes, related to functionality now in net-next.
1. delaying the automatic bring up of VF device to allow udev to change name.
2. performance improvement
3. handle MAC address change with VF; mostly propogate the error that VF gives.
4. minor cleanups
5. allow setting send/receive buffer size with ethtool.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool statistics for case where send chimmeny buffer is
exhausted and driver has to fall back to doing scatter/gather
send. Also, add statistic for case where ring buffer is full and
receive completions are delayed.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Control the size of the buffer areas via ethtool ring settings.
They aren't really traditional hardware rings, but host API breaks
receive and send buffer into chunks. The final size of the chunks are
controlled by the host.
The default value of send and receive buffer area for host DMA
is much larger than it needs to be. Experimentation shows that
4M receive and 1M send is sufficient.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function init_page_array is always called with a valid pointer
to RNDIS header. No check for NULL is needed.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Assignment to a typed pointer is sufficient in C.
No cast is needed.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The send and receive buffers are both per-device (not per-channel).
The associated NUMA node is a property of the CPU which is per-channel
therefore it makes no sense to force the receive/send buffer to be
allocated on a particular node (since it is a shared resource).
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If setting new values fails, and the attempt to restore original
settings fails. Then log an error and leave device down.
This should never happen, but if it does don't go down in flames.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If VF is slaved to synthetic device, then any change to netvsc
MAC address should be propagated to the slave device.
If slave device doesn't support MAC address change then it
should also be an error to attempt to change synthetic NIC MAC
address.
It also fixes the error unwind in the original code.
If give a bad address, the old code would change the device
MAC address anyway.
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hv_pkt_iter_next() returns NULL, it has already called
hv_pkt_iter_close(). Calling it twice can lead to extra host signal.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VF device is discovered, delay bring it automatically up in
order to allow userspace to some simple changes (like renaming).
Reported-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA layer frees the original skb when an xmit function returns NULL,
meaning an error occurred. But if the tagging code copied the original
skb, it is responsible of freeing the copy if an error occurs.
The ksz tagging code currently has two issues: if skb_put_padto fails,
the skb copy is not freed, and the original skb will be freed twice.
To fix that, move skb_put_padto inside both branches of the skb_tailroom
condition, before freeing the original skb, and free the copy on error.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When deleting a queue, clear its corresponding bit in the qmask, vfree its
memory, clear out the pointer that's pointing to it, and decrement the
queue count.
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: Felix Manlunas <fmanlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
