This patch provides the infrastructure for the Digidesign Mbox 1
to have a mixer control for selecting the clock source.
Valid options are Internal and S/PDIF external sync.
A non-documented command is sent to the device to enable this feature
found by reverse engineering and bus snooping.
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Output driver has two parameters that can be configured to reduce
pop noise: power-on delay and ramp-up step time. Two new kcontrols
have been added to set these parameters.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is easier to find the relevant enums in the code. Use the
SOC_ENUM_*_DECL macro for the individual items.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove rt5645_clk_sel_put function since it is never used.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5672 is very similar to rt5670. Therefore we use one codec driver
to support both codecs. The difference between rt5670 and rt5672 is
there is some difference in their dapm routing table.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Needed due to some important regression fixes at RC core.
* commit 'v3.18-rc4': (587 commits)
Linux 3.18-rc4
ARM: dts: zynq: Enable PL clocks for Parallella
tiny: rename ENABLE_DEV_COREDUMP to ALLOW_DEV_COREDUMP
tiny: reverse logic for DISABLE_DEV_COREDUMP
i2c: core: Dispose OF IRQ mapping at client removal time
i2c: at91: don't account as iowait
i2c: remove FSF address
USB: Update default usb-storage delay_use value in kernel-parameters.txt
sysfs: driver core: Fix glue dir race condition by gdp_mutex
MIPS: Fix build with binutils 2.24.51+
xfs: track bulkstat progress by agino
xfs: bulkstat error handling is broken
xfs: bulkstat main loop logic is a mess
xfs: bulkstat chunk-formatter has issues
xfs: bulkstat chunk formatting cursor is broken
xfs: bulkstat btree walk doesn't terminate
mm: Fix comment before truncate_setsize()
USB: cdc-acm: add quirk for control-line state requests
tty: Fix pty master poll() after slave closes v2
MIPS: R3000: Fix debug output for Virtual page number
...
Conflicts:
drivers/media/rc/rc-main.c
Instead of registering the irq name with the driver name, it's better to pass
the device name so that we have a more explicit indication as to what saif
instance the irq is related:
$ cat /proc/interrupts
CPU0
...
214: 4 - 59 80042000.saif
215: 0 - 58 80046000.saif
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm8962 uses the snd_soc_codec mutex to protect the wm8962_dsp2_ena_put()
function from concurrent execution. This patch moves that lock to the driver
level. This will allow us to eventually remove the snd_soc_codec mutex.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm8958 driver uses the snd_soc_codec mutex to protect the various
firmware pointers from concurrent assignment. This patch moves this lock to
the driver level. This will allow us to eventually remove the snd_soc_codec
mutex.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm8903 uses the snd_soc_codec mutex to protect its deemph settings from
concurrent access. This patch moves this lock to the driver level. This will
allow us to eventually remove the snd_soc_codec mutex.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm8731 uses the snd_soc_codec mutex to protect its deemph settings from
concurrent access. This patch moves this lock to the driver level. This will
allow us to eventually remove the snd_soc_codec mutex.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm5102 driver currently uses the snd_soc_codec mutex to protect its
ultrasonic response settings from concurrent access. This patch moves this
lock to the driver level. This will allow us to eventually remove the
snd_soc_codec mutex.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The max98095 uses the snd_soc_codec mutex to protect against concurrent
access in some of its control put handlers. Move this mutex to the driver
level so we can eventually remove the snd_soc_codec mutex.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ab8500 driver uses a driver specific lock to protect concurrent access
to some of the control put/get handlers and uses the snd_soc_codec mutex for
some others. This patch updates the driver to consistently use the driver
specific lock for all controls. This will allow us to eventually remove the
snd_soc_codec mutex.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to cast the cpu_of_node or codec_of_node of the
dai_links when calling of_put_node.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds Volume Ramp to Renesas sound driver.
amixer set "DVC Out" 100%
amixer set "DVC Out Ramp Up Rate" "0.125 dB/64 steps"
amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
amixer set "DVC Out Ramp" on
aplay xxx.wav &
amixer set "DVC Out" 80% // Volume Down
amixer set "DVC Out" 100% // Volume Up
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Active slots count depends on the number of channels in the stream
and the number of active serializers. Each serializer will handle
at most the number of channels specified via 'tdm-slots' parameter
in DT.
There are two possible scenarios:
- Single serializer: channel count fits in the max slots supported by
McASP serializers, active slots is same as channel count
- Multiple serializers: channel count is bigger than max slots supported
by a serializer. Channel count determines how many serializers are
needed at their max slot count configuration
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In IIS (I2S, TDM, etc) mode the maximum number of allowed channels for
either direction can be:
number of serializers for the direction * tdm_slots.
This constraint applicable for the first stream, while consequent stream
should not have more channels then the first stream.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of validating the tdm_slots parameter every time at hw_params we
can do it once during probe. If the parameter is not valid (<2 or >32)
print an error and fix it up.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the bus is configured to have more BCLK then the data type demands we
need to use the rotation to move the data to correct place.
Reported-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In IIS mode the tx and rx configuration is symmetric, the BCLK and FSYNC is
shared.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas R-Car sound driver probe will be failed
if it try to use DMA mode and it couldn't use for some reasons.
But PIO mode works even though in such case.
This patch try to fallback to PIO mode if DMA mode probing was failed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas R-Car sound driver debug message
is using random format
(ex "ssi0: xxx" / "SSI0 xxx" / "ssi[0]: xxx")
and confusable timing
("xxx probe failed" and "xxx probed" are shown in same time)
This patch fixes these
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If probe fails then we need to call pm_runtime_disable() to balance
out the previous pm_runtime_enable() call.
Signed-off-by: Anil Kumar <anilk4.v@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With device tree, it is possible (and encouraged) to build N900
kernels without CONFIG_MACH_NOKIA_RX51. Update config file to enable
the driver build in this case.
This makes sound work on my n900 under 3.18-rc1.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
TDM support is achieved using DSP transfer mode and setting a
programmable offset which specifies where data begins with
respect to the frame sync.
It requires 256-clock mode if CODEC is master (not currently
supported in the driver). No additional dependency if CODEC
is slave.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The quirk argument itself was used as iterator, so it cannot be taken
back to the original value, obviously.
Fixes: d4b8fc66f7 ('ALSA: usb-audio: Allow multiple entries for the same iface in composite quirk')
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix a copy & paste error:
Warning(sound/core/pcm_native.c:1112): Excess function parameter 'state' description in 'snd_pcm_stop_xrun'
The state argument was dropped from snd_pcm_stop_xrun().
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently the composite quirk doesn't work when multiple entries are
assigned to the same interface because it marks the interface as
claimed then checks whether the interface has been already claimed for
the secondary entry. But, if you look at the code, you'll notice that
multiple entries are allowed if the entry is the current interface;
i.e. the current behavior is anyway inconsistent, and this is an
unintended shortcoming.
This patch fixes the problem by marking the relevant interfaces as
claimed after applying the all composite entries. This fix will be
needed for the upcoming enhancements for Digidesign Mbox 1 quirks.
Reviewed-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new helper function snd_pcm_stop_xrun() to the standard sequnce
lock/snd_pcm_stop(XRUN)/unlock by a single call, and replace the
existing open codes with this helper.
The function checks the PCM running state to prevent setting the wrong
state, too, for more safety.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This function has no more non regmap user, which means we can remove the
implementation of the function and associated functions and structure
fields.
For convenience we keep a static inline version of the function that
forwards calls to regcache_sync() unconditionally.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
For convenience for drivers that do not want to keep their own pointer to
regmap struct around forward calls to snd_soc_cache_sync() to
regcache_sync() if the driver is using regmap. This is similar to what we do
for snd_soc_read()/snd_soc_write().
This patch also fixes drivers which already have been converted to regmap,
but still use snd_soc_cache_sync() for trying to the sync the cache.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm9712/wm9713 has separate mixers for the left and the right channel,
but the inputs to the mixers are enabled/disabled by the same control.
Currently this is implemented by the driver by registering two virtual
controls for each physical control, one for the left mixer and one for the
right mixer.
Using virtual registers will no longer work when the driver has
been converted to regmap. This patch converts the driver to use controls
with custom put/get callbacks instead which implement the logic making sure
that the physical control is unmuted when either the left or the right
control is unmuted.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
We want to know the offset for the id that was passed to the function, not
the offset of the first id of the control (which is always 0).
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In DSP mode, the register r/w should use the specific function to access
that is invoked by address mapping of the DSP.
The MX-65[1] is for switching DSP or codec mode.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Exynos7 I2S controller has no internal dma, supports more
no. of root clock sampling frequencies and has more no.of Rx
fifos to support 7.1CH recording in TDM mode. Due to more no.
of root clock frequency values some of the bit offsets got
shifted up by one. Also I2S1 on previous Samsung platforms
uses v3 dai type but on Exynos7 it is upgraded to v5 with
slightly modified register offsets for supporting more no.of
RFS values. Due to the above changes, the driver has to be
modified to handle all versions of I2S controller. For this
I introduced a new structure to hold modified bit offsets and
masks which is passed as dai data.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Internal DMA is available only on some of Samsung platforms.
So added a quirk for the same and made it optional.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DVC controls some digital volume features.
Volume Ramp is listed as "XX dB / YY steps",
and this enumerated settings are easy for users.
This patch adds rsnd_dvc_cfg_e and care about
enumerated settings.
Compiler will report like below at this point,
but, it will be removed if Volume Ramp was supported.
warning: '_rsnd_dvc_pcm_new_e' defined but not used
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DVC controls some digital volume features.
Some of them requests values for "each channels",
but, some of them requests values for "feature".
And, Volume Ramp has "feature" settings.
This patch adds rsnd_dvc_cfg_s and care about
single settings.
Compiler will report like below at this point,
but, it will be removed if Volume Ramp was supported.
warning: '_rsnd_dvc_pcm_new_s' defined but not used
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DVC controls some digital volume features.
Some of them requests values for "each channels",
but, some of them requests values for "feature".
Current dvc.c is supporting Mute/Volume,
and these have "each channels" settings.
This patch adds rsnd_dvc_cfg_m and care about
multiple settings for each channels.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need to Enable/Disable DVC_DVUER register if we set
DVCp_ZCMCR, DVCp_VRCTR, DVCp_VRPDR, DVCp_VRDBR,
DVCp_VOL0R, DVCp_VOL1R, DVCp_VOL2R, DVCp_VOL3R,
DVCp_VOL4R, DVCp_VOL5R, DVCp_VOL6R, DVCp_VOL7R
and, these are controlled under rsnd_dvc_volume_update().
This patch moves DVC_DVUER settings to it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
