Current alsa_sound_last_init() was called as __initcall().
So, on current ALSA, only devices that had been properly
registered at this point were shown.
So, it will show "No soundcards found" if driver requests
probe deferment. it's often misleading.
This patch delays the timing of alsa_sound_last_init()
as workaround.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
While refactoring the mute-LED handling for HP laptops, I messed up
the polarity check in a wrong way. The red (or the mute-LED if any)
should appear in the muted state, corresponding to GPIO on.
Reported-by: Mikko Vinni <mmvinni@yahoo.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Through the transition to the auto-parser, the support for
Quanta/Gericom KN1 got broken. There are two problems behind it:
- This machine doesn't like the default COEF setup for ALC260 we take
now as default
- BIOS doesn't set the pins correctly at all; especially the machine
uses only the pin 0x0f for both headphone and speaker
This patch adds the fixup as a workaround for these issues.
Reported-and-tested-by: Uros Vampl <mobile.leecher@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In preparation for ASoC DSP support.
Add a DAPM API call to determine whether a DAPM audio path is valid between
source and sink widgets. This also takes into account all kcontrol mux and mixer
settings in between the source and sink widgets to validate the audio path.
This will be used by the DSP core to determine the runtime DAI mappings
between FE and BE DAIs in order to run PCM operations.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Connect the WM1250-EV1 baseband simulator on Littlemill systems up to
the CODEC AIF2 using the new CODEC<->CODEC link support, allowing a wider
range of use cases to be represented.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Leading up to the ->device_prep_slave_sg change in
185ecb5f4f 'dmaengine: add context
parameter to prep_slave_sg and prep_dma_cyclic' a generic wrapper was
added in place to guard against the API change, though the fsi driver
wasn't updated in the process (presumably its dmaengine support hadn't
been merged yet at the time). This trivially switches over to the new
wrapper and gets it building again.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix kernel-doc warning in sound/core/vmaster.c:
Warning(sound/core/vmaster.c:429): No description found for parameter 'private_data'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is nothing audio-specific about the rcode_string() helper, so move
it from snd-firewire-lib into firewire-core to allow other code to use it.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (fixed sound/firewire/cmp.c)
Since AIF3 shares clock signals with other audio interfaces in order to
ensure it doesn't drive undesirable clocks we need to tristate it. Rather
than forcing the machine driver to do so have the driver do this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently we increment the number of RTD's per card during the DAI link
bind. This can cause an incorrect RTD count when we cannot find a component
and defer the probe (and hence perform the DAI link bind for the card again).
Fix the count so that it is cleared before every card registration
and bind attempt.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current DA7210 driver does support PLL mode fully. It uses fixed
value of input master clock and PLL mode is enabled and disabled based
on the sampling frequency being used for playback or recording. It also
doesn't support Sample Rate Measurement feature of DA7210 hardware.
This patch adds full support for PLL and SRM. Basically following three
modes of operation are possible for DA7210 hardware,
(1) I2S SLAVE mode with PLL bypassed
(2) I2S SLAVE mode with PLL enabled
(3) I2S Master mode with PLL enabled
This patch adds support for all three modes. Also, in case of SLAVE mode
with PLL, it supports SRM (Sample Rate Measurement) feature of the chip.
Actually this patch was submitted earlier and received some review
comments, but after that the driver got update by other patches. Because
of that, I am considering this as new patch and not versioning it based
of previous patches. This version tries to take care of all review
comments received for earlier submissions.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Linux 3.4-rc3 contains a bunch of Tegra changes which are conflicting
annoyingly with the new development that's going on for Tegra so merge
it up to resolve those conflicts.
Conflicts:
sound/soc/soc-core.c
sound/soc/tegra/tegra_i2s.c
sound/soc/tegra/tegra_spdif.c
Fix the following build warning:
sound/soc/soc-dapm.c: In function 'snd_soc_dai_link_event':
sound/soc/soc-dapm.c:2913: warning: format '%lx' expects type 'long unsigned int', but argument 3 has type 'u64'
'%llx' should be used with 'u64' type.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than having the user half start a stream but avoid any DMA to
trigger data flow on links which don't pass through the CPU create a
DAPM route between the two DAI widgets using a hw_params configuration
provided by the machine driver with the new 'params' member of the
dai_link struct. If no configuration is provided in the dai_link then
use the old style even for CODEC<->CODEC links to avoid breaking
systems.
This greatly simplifies the userspace usage of such links, making them
as simple as analogue connections with the stream configuration being
completely transparent to them.
This is achieved by defining a new dai_link widget type which is created
when CODECs are linked and triggering the configuration of the link via
the normal PCM operations from there. It is expected that the bias
level callbacks will be used for clock configuration.
Currently only the DAI format, rate and channel count can be configured
and currently the only DAI operations which can be called are hw_params
and digital_mute(). This corresponds well to the majority of CODEC
drivers which only use other callbacks for constraint setting but there
is obviously much room for extension here. We can't simply call
hw_params() on startup as things like the system clocking configuration
may change at runtime and in future it will be desirable to offer some
configurability of the link parameters.
At present we are also restricted to a single DAPM link for the entire
DAI. Once we have better support for channel mapping it would also be
desirable to extend this feature so that we can propagate per-channel
power state over the link.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
We should always have a CODEC already there when registering a CODEC DAI
and for CODEC<->CODEC links a dai_link will have two CODECs so it's much
simpler to do things at registration time.
This results in a slight change in the error handling for failed CODEC
DAI registrations but practically speaking these are never supposed to
fail so there shouldn't be much issue. The change is that we don't fail
the overall CODEC registration if the DAI registration fails; this seems
more robust anyway as we may not need to use a given DAI in a particular
system.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When two CODEC DAIs are linked directly to each other then if we give the
same master mode settings to both devices things won't work as either
neither will drive or they'll drive against each other. Flip the settings
for the DAI in the CPU slot of the DAI link.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In order to allow CODEC<->CODEC links to function we will need to allow
DAPM paths to be created that pass through DAIs rather than only ones
that are source or sunk at the DAI.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
This helps us ignore errors in callers if the operation failed due to not
being available as opposed to an error.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Complete the separation of the twl6040 from the twl core since
it is a separate chip, not part of the twl6030 PMIC.
Make the needed Kconfig changes for the depending drivers at the
same time to avoid breaking the kernel build (vibra, ASoC components).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Pull another round of sound fixes from Takashi Iwai:
"A few regression fixes for Realtek HD-audio codecs, mainly specific to
some laptop models."
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - Fix mem leak (and rid us of trailing whitespace).
ALSA: hda/realtek - Add quirk for Mac Pro 5,1 machines
ALSA: hda/realtek - Add a fixup entry for Acer Aspire 8940G
ALSA: hda/realtek - Fix GPIO1 setup for Acer Aspire 4930 & co
ALSA: hda/realtek - Add a few ALC882 model strings back
The mixer units from the firmware are corrupt, and even where they
are valid they presents mono controls as L and R channels of
stereo.
Signed-off-by: Mark Hills <mark@pogo.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some interfaces reference endpoints which do not exists. To
accomodate these, do not fail completely, but skip over them.
This allows the Electrix Ebox-44 with earlier firmware to be
detected and used for audio.
Signed-off-by: Mark Hills <mark@pogo.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Many fields have been moved to struct snd_usb_endpoint.
Also fix the proc output to correspond to the new structure.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ep->fill_max is a 1 bit flag, thus it has to be boolean.
sound/usb/endpoint.c: In function 'snd_usb_endpoint_set_params':
sound/usb/endpoint.c:785: warning: overflow in implicit constant conversion
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch uses simple-card driver instead of fsi-da7210 on each board.
To select DA7210 driver, each boards select it on Kconfig.
This patch removes fsi-da7210 driver which is no longer needed
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch uses simple-card driver instead of fsi-ak4642 on each board.
To select AK4642 driver, each boards select it on Kconfig.
This patch removes fsi-ak4642 driver which is no longer needed
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current ASoC requires card.c file to each platforms in order to
specifies its CPU and Codecs pair.
But the differences between these were only value/strings of setting.
In order to reduce duplicate driver, this patch adds generic/simple-card.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This adds Kconfig options for the Tegra30 AHUB and I2S controller, and
updates the Tegra+WM8903 machine driver Kconfig to select those.
Includes a squashed bugfix from Sumit Bhattacharya <sumitb@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The AHUB (Audio Hub) is a mux/crossbar which links all audio-related
devices except the HDA controller on Tegra30. The devices include the
DMA FIFOs, DAM (Digital Audio Mixers), I2S controllers, and SPDIF
controller. Audio data may be routed between these devices in various
combinations as required by board design/application.
Includes a squashed bugfix from Nikesh Oswal <noswal@nvidia.com>
Includes squashed bugfixes from Sumit Bhattacharya <sumitb@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If cs42l73_get_mclkx_coeff() returns < 0 (which it can) in
sound/soc/codecs/cs42l73.c::cs42l73_set_mclk(), then we'll be using
the (negative) return value as array index on the very next line of
code - that's bad.
Catch the negative return value and propagate it to the caller (which
checks for it) and things are a bit more sane :-)
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Document the new streaming code and some of the functions so that
contributers can catch up easier.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Implicit feedback is a streaming mode that does not rely on dedicated
sync endpoints but uses the information provided by record streams to
clock output streams. Now that the streaming logic is decoupled from the
PCM streams, this is easy to implement.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With the previous commit that added the new streaming model, all
endpoint and streaming related code is now in endpoint.c, and pcm.c
only acts as a wrapper for handling the packet's payload.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds a new generic streaming logic for audio over USB.
It defines a model (snd_usb_endpoint) that handles everything that
is related to an USB endpoint and its streaming. There are functions to
activate and deactivate an endpoint (which call usb_set_interface()),
and to start and stop its URBs. It also has function pointers to be
called when data was received or is about to be sent, and pointer to
a sync slave (another snd_usb_endpoint) that is informed when data has
been received.
A snd_usb_endpoint knows about its state and implements a refcounting,
so only the first user will actually start the URBs and only the last
one to stop it will tear them down again.
With this sort of abstraction, the actual streaming is decoupled from
the pcm handling, which makes the "implicit feedback" mechanisms easy to
implement.
In order to split changes properly, this patch only adds the new
implementation but leaves the old one around, so the the driver doesn't
change its behaviour. The switch to actually use the new code is
submitted separately.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In sound/pci/hda/patch_realtek.c::alc_auto_fill_dac_nids(), in the
'for (;;)' loop, if the 'badness' value returned from
fill_and_eval_dacs() is negative, then we'll return from the function
without freeing the memory we allocated for 'best_cfg', thus leaking.
Fix the leak by kfree()'ing the memory when badness is negative.
While I was there I also noticed some trailing whitespace in the
function that I removed (along with all other trailing whitespace in
the file) - it didn't seem worth-while to do that as two patches, so I
hope it's OK that I just did it all as one patch.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
