The common driver needs the packet overhead for the bus in order
to reserve headroom for sk_buffs. For the SDIO driver this depends
on firmware features so it is not possible to provide it in the
brcmf_attach() call.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When using fwsignal it is possible that tx packets get delivered out
of order. This patch fixes that by reordering suppressed packets and
tracking generation bit and sequence number per packet.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Baseband updates
* Remove ar9340Common_rx_gain_table_1p0 since it is a duplicate.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The initvals for AR9462 v2.1 are very similar to v2.0.
Identify duplicate arrays and reuse the values from v2.0
to reduce module size.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The initialization arrays for v1.1 AR9565
are mostly the same as v1.0/v1.0.1 except for
radio_postamble.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since IQ calibration is done as part of AGC calibration for
AR9485 and above, remove the seperate IQ calibration code.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The CHANNEL_HT flag is insignificant for fast channel change conditions,
since it does not affect any important part of the hardware reset /
channel setup.
Scanning usually runs with HT disabled, so this change will slightly
improve scan time on many chipsets.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A cold reset can be triggered because of DMA stop issues, and this leads
to TSF being cleared on all chipsets. To properly deal with this, always
save the TSF.
Additionally, account for the time it takes to do the actual chip reset,
which can be quite significant. On AR9344 it takes around 4.5 ms.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of checking the queues in a loop with hardcoded sleep times
inbetween, use a wait queue to trigger queue checks after the tx
processing tasklet has run.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the software has processed all packets, checking the hardware queue
is unnecessary.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When operating in client mode, the short period of time between scanning
and associating is often enough to put the hardware through several
FULL-SLEEP <-> AWAKE transitions, each wakeup requiring a reset to fully
recover the hardware.
This is completely unnecessary and can easily be avoided by deferring
the switch to full sleep.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since calibration data reuse is not enabled in
SoC chips, simplify the IQ calibration code.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CL calibration is applicable for all chips and the
enable/disable knob comes via the INI file. For PCOEM
chips, the calibration data is reused when Fast Channel Change
is used. Caldata reuse is not enabled for SoC chips, so remove
the CL post processing code.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RTT is enabled only for AR9462 and MCI for AR9462/AR9565.
Also, manual peak calibration is not done for any of the
SoC chips.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Though there is some overlap between the calibration mechanisms
of PC-OEM cards and SoC chip families, dumping both of them
into a single function makes things hard to understand.
ar9003_hw_init_cal() is unreadable with chip-specific segments
scattered around. To make the logic understandable, use
different functions for client cards and SoC chips. Some
code is duplicated, but in the long run, it makes the code
more maintanable.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SC_OP_INVALID is zero so the test is always false. We're supposed to be
testing the lowest bit instead.
Fixes: 89f927af7f ('ath9k: add TX99 support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the WoW code to wow.c and compile it conditionally
based on CONFIG_ATH9K_WOW.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HW routines to set various WoW registers are present
in wow.c. For some reason, it has been compiled as part
of the main ath9k.ko module all this time, when it should
really be part of ath9k_hw.ko. This patch renames the file to
ar9003_wow.ko and adds it to ath9k_hw.ko.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use CONFIG_ATH9K_TX99 to properly enclose the tx99 code
and make sure that it is not compiled as part of the driver
when it is not selected. Move the tx99 code to a new file tx99.c
and also add ATH9K_DEBUGFS as a dependency in Kconfig.
This reduces the module size on platforms like OpenWrt where
ATH9K_DEBUGFS is selected, but TX99 might be disabled.
Cc: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Building brcmfmac for sparc64 gave the following warning:
CC [M] drivers/net/wireless/brcm80211/brcmfmac/bcmsdh_sdmmc.o
bcmsdh_sdmmc.c: In function 'brcmf_sdioh_request_byte':
bcmsdh_sdmmc.c:89:6: warning: 'err_ret' may be used uninitialized
in this function [-Wuninitialized]
Inspecting the code it indeed had a path of execution in
which the return value was used uninitialized. This patch
fixes that code path.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If kmalloc fails wcn36xx_smd_rsp_process will attempt to dereference
a NULL pointer. There might be a better error recovery then just
printing an error, but printing an error message is better then the
current behaviour.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Code in ath9k_hw_set_clockrate function indicates that ah->curchan
(and thus chan local variable) may be NULL. If that is indeed the
case, IS_CHAN_HT40(chan) check has to be performed only in branch
where chan is not NULL. Moving the code under already existing
if condition fixes this issue.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The EEPROM parameter to determine whether the bias
strength values for XLNA have to be applied is part
of the miscConfiguration field and not featureEnable.
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bit 5 in the miscConfiguration field of the base EEPROM
header denotes whether QuickDrop is enabled or not. Fix
the incorrect usage of BIT(1) and also make sure that
this is done only for the required chips.
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull networking updates from David Miller:
"Here is a pile of bug fixes that accumulated while I was in Europe"
1) In fixing kernel leaks to userspace during copying of socket
addresses, we broke a case that used to work, namely the user
providing a buffer larger than the in-kernel generic socket address
structure. This broke Ruby amongst other things. Fix from Dan
Carpenter.
2) Fix regression added by byte queue limit support in 8139cp driver,
from Yang Yingliang.
3) The addition of MSG_SENDPAGE_NOTLAST buggered up a few sendpage
implementations, they should just treat it the same as MSG_MORE.
Fix from Richard Weinberger and Shawn Landden.
4) Handle icmpv4 errors received on ipv6 SIT tunnels correctly, from
Oussama Ghorbel. In particular we should send an ICMPv6 unreachable
in such situations.
5) Fix some regressions in the recent genetlink fixes, in particular
get the pmcraid driver to use the new safer interfaces correctly.
From Johannes Berg.
6) macvtap was converted to use a per-cpu set of statistics, but some
code was still bumping tx_dropped elsewhere. From Jason Wang.
7) Fix build failure of xen-netback due to missing include on some
architectures, from Andy Whitecroft.
8) macvtap double counts received packets in statistics, fix from Vlad
Yasevich.
9) Fix various cases of using *_STATS_BH() when *_STATS() is more
appropriate. From Eric Dumazet and Hannes Frederic Sowa.
10) Pktgen ipsec mode doesn't update the ipv4 header length and checksum
properly after encapsulation. Fix from Fan Du.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits)
net/mlx4_en: Remove selftest TX queues empty condition
{pktgen, xfrm} Update IPv4 header total len and checksum after tranformation
virtio_net: make all RX paths handle erors consistently
virtio_net: fix error handling for mergeable buffers
virtio_net: Fixed a trivial typo (fitler --> filter)
netem: fix gemodel loss generator
netem: fix loss 4 state model
netem: missing break in ge loss generator
net/hsr: Support iproute print_opt ('ip -details ...')
net/hsr: Very small fix of comment style.
MAINTAINERS: Added net/hsr/ maintainer
ipv6: fix possible seqlock deadlock in ip6_finish_output2
ixgbe: Make ixgbe_identify_qsfp_module_generic static
ixgbe: turn NETIF_F_HW_L2FW_DOFFLOAD off by default
ixgbe: ixgbe_fwd_ring_down needs to be static
e1000: fix possible reset_task running after adapter down
e1000: fix lockdep warning in e1000_reset_task
e1000: prevent oops when adapter is being closed and reset simultaneously
igb: Fixed Wake On LAN support
inet: fix possible seqlock deadlocks
...
FW 10.1 seems to require the default key index to
be updated to point to group key after it is
installed. Otherwise Txed frames are corrupted.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The channel switch notification should be sent under the
wdev/sdata-lock, preferably in the same moment as the channel change
happens, to avoid races by other callers (e.g. start/stop_ap).
This also adds the previously missing sdata_lock protection in
csa_finalize_work.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change cfg80211 and mac80211 to use cfg80211_mgmt_tx_params
struct to aggregate parameters for mgmt_tx functions.
This makes the functions' signatures less clumsy and allows
less painful parameters extension.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
[fix all other drivers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The beacon timers really shouldn't use any clock that is
subject to adjustments from userspace, particularly not
CLOCK_REALTIME. Use CLOCK_MONOTONIC_RAW instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove waiting for TX queues to become empty during selftest.
This check is not necessary for any purpose, and might put
the driver into an infinite loop.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
receive mergeable now handles errors internally.
Do same for big and small packet paths, otherwise
the logic is too hard to follow.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet noticed that if we encounter an error
when processing a mergeable buffer, we don't
dequeue all of the buffers from this packet,
the result is almost sure to be loss of networking.
Jason Wang noticed that we also leak a page and that we don't decrement
the rq buf count, so we won't repost buffers (a resource leak).
Fix both issues.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael Dalton <mwdalton@google.com>
Reported-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NETIF_F_HW_L2FW_DOFFLOAD allows upper layer net devices such
as macvlan to use queues in the hardware to directly submit and
receive skbs.
This creates a subtle change in the datapath though. One change
being the skb may no longer use the root devices qdisc.
Because users may not expect this we can't enable the feature
by default unless the hardware can offload all the software
functionality above it. So for now disable it by default and
let users opt in.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
