Found several incorrect conditionals after calling the prot_autoc_*
functions. Likewise we weren't always freeing the FWSW semaphore after
grabbing it. This would lead to DA cables being unable to link along with
possible other errors.
CC: Arun Sharma <asharma@fb.com>
CC: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The use of __constant_<foo> has been unnecessary for quite awhile now.
Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The use of __constant_<foo> has been unnecessary for quite awhile now.
Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The use of __constant_<foo> has been unnecessary for quite awhile now.
Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The use of __constant_<foo> has been unnecessary for quite awhile now.
Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The use of __constant_<foo> has been unnecessary for quite awhile now.
Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For i350 VLAN stripping for VMs is not enabled in the VMOLR register but in
the DVMOLR register. Making the changes accordingly. It's not necessary to
unset the E1000_VMOLR_STRVLAN bit on i350 as the hardware will simply ignore
it.
Without this change if a VLAN is configured for a VF assigned to a guest
via (i.e.)
ip link set p1p1 vf 0 vlan 10
the VLAN tag will not be stripped from packets going into the VM. Which they
should be because the VM itself is not aware of the VLAN at all.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to i40e, i40evf, e1000e, ixgbe and ixgbevf.
Mitch adds support for the VF link state ndo which allows the PF driver
to control the virtual link state of the VF devices. Added
support for viewing and modifying RSS hash options and RSS hash look-up
table programming through ethtool for i40evf. Fixed complaint about
the use of min() where min_t() should be used in i40evf.
Anjali adds support for ethtool -k option for NTUPLE control for i40e.
Elizabeth cleans up and refactors i40e_open() to separate out the VSI
code into its own i40e_vsi_open().
Jesse enables the hardware feature head write back to avoid updating the
descriptor ring by marking each descriptor with a DD bit and instead
writes a memory location with an update to where the driver should clean
up to in i40e and i40evf. Reduces context descriptors for i40e/i40evf
since we do not need context descriptors for every packet, only for
TSO or timesync.
Dan Carpenter fixes a potential array underflow in i40e_vc_process_vf_msg().
Dave fixes an e1000e hardware unit hang where the check for pending Tx work
when link is lost was mistakenly moved to be done only when link is first
detected to be lost. Fixed a problem with poor network performance on
certain silicon in e1000e when configured for 100M HDX performance.
Carolyn adds register defines needed for time sync functions and the code
to call the updated defines.
Jacob adds the ixgbe function for writing PCI config word and checks
whether the adapter has been removed first.
Mark adds the bit __IXGBEVF_REMOVING to indicate that the module is being
removed because the __IXGBEVF_DOWN bit had been overloaded for this
purpose, but leads to trouble. ixgbevf_down function can now prevent
multiple executions by doing test_and_set_bit on __IXGBEVF_DOWN.
v2:
- dropped patch Mitch's patch "i40evf: Support RSS option in ethtool"
based on feedback from Ben Hutchings so that Mitch can re-work the
patch solution
v3:
- removed unnecessary parenthesis in patch 1 based on feedback from David
Miller
- changed a macro to get the next queue to a function in patch 2 based on
feedback from David Miller
- added blank lines after variable declaration and code in two functions
in patch 6 based on feedback from David Miller
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The ixgbevf_down function can now prevent multiple executions by
doing test_and_set_bit on __IXGBEVF_DOWN. This did not work before
introduction of the __IXGBEVF_REMOVING bit, because of overloading
of __IXGBEVF_DOWN. Also add smp_mb__before_clear_bit call before
clearing the __IXGBEVF_DOWN bit.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a bit, __IXGBEVF_REMOVING, to indicate that the module is being
removed. The __IXGBEVF_DOWN bit had been overloaded for this purpose,
but that leads to trouble. A few places now check both __IXGBEVF_DOWN
and __IXGBEVF_REMOVING.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Inline with the current use for ixgbe_read_pci_cfg_word, create a
similar function for writing PCI config, which checks whether the
adapter has been removed first, if Live Error Recovery has been enabled.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The check for pending Tx work when link is lost was mistakenly moved to be
done only when link is first detected to be lost. It turns out there is a
small window of opportunity for additional Tx work to get queued up shortly
after link is dropped.
Move the check back to the place it was before in the watchdog task. Put in
additional debug information for other reset paths and a final catch-all for
false hangs in the scheduled function that prints out the hardware hang
message.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If "vf_id" is smaller than hw->func_caps.vf_base_id then it leads to
an array underflow of the pf->vf[] array. This is unlikely to happen
unless the hardware is bad, but it's a small change and it silences a
static checker warning.
Fixes: 7efa84b7ab ('i40e: support VFs on PFs other than 0')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't need context descriptors for every packet, only tso
or timesync. This fixes a bug in the driver where it would
always add a context even if all the passed in values
to the context descriptor function were 0/default values.
Change-ID: I0101d2b893380707b5c2de61aab3e16d4310e9a1
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hardware supports a feature to avoid updating the descriptor
ring by marking each descriptor with a DD bit, and instead
writes a memory location with an update to where the driver
should clean up to. Enable this feature.
Change-ID: I5da4e0681f0b581a6401c950a81808792267fe57
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This enables option '-k/-K' in ethtool for NTUPLE control.
NTUPLE control requires a reset, to take effect. When the feature is
turned off, the SW list of stored FD SB filters gets cleaned up.
Change-ID: I9d564b67a10d4afa11de3b320d601c3d2e6edc1f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Checkpatch complained in an earlier patch about using min(), but that
change would have been completely unrelated to the point of that patch.
So fix it here.
Change-ID: I2cd87b39cfd406850d283b88f259757a6bcd14cd
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The HLUT programming loop in in i40evf_configure_rss was a) overly-
complicated, and b) just plain broken. Most of the entries ended up being
not written at all, so most of the flows ended up at queue zero.
Refactor the HLUT programming loop to simply walk through the registers
and write four values to each one, incrementing through the number of
available queues.
Change-ID: I75766179bc67e4e997187794f3144e28c83fd00d
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This netdev op allows the PF driver to control the virtual link state of
the VF devices. This can be used to deny naughty VF drivers access to
the wire, or to allow VFs (regardless of temperament) to communicate
with each other over the device's internal switch even though external
link is down.
Add the actual ndo function, and modify vc_notify_link_state to check
the link status of each VF before sending a message in the case when
physical link changes state.
Change-ID: Ib5a6924da78c540789f21d26b5e8086d71c29384
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To set AP in 1X1 or 2X2 mode through hostapd, we need to set
RX-STBC* in hostapd.conf file. Depending upon RX-STBC bit in
ht_cap IE received from hostapd, we need to update mcs set in
bss_cfg appropriately before starting AP.
Signed-off-by: Maithili Hinge <maithili@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support to read sleep cookie for command
response before accessing buffer.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stations associated to mwifiex AP would not be able to ping AP
after scan was issued on AP interface. This happened because
there was no handling of extended scan event in AP. This patch
adds this handling and fixes ping failure issue.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emit a prefix for the rsi_dbg messages.
Fix the format and argument mismatch and add
__printf(2, 3) to try to avoid more.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ERP configuration is now done outside RF code in both rtl8180
and rtl8187 drivers.
The conf_erp callback in common RF ops struct is now useless.
Remove it.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes the build for powerpc:
After merging the final tree, today's linux-next build (powerpc allyesconfig)
failed like this:
drivers/net/wireless/iwlwifi/mvm/debugfs.c: In function 'iwl_dbgfs_fw_error_dump_release':
drivers/net/wireless/iwlwifi/mvm/debugfs.c:161:2: error: implicit declaration of function 'vfree' [-Werror=implicit-function-declaration]
vfree(file->private_data);
^
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This is to address reports of this:
In file included from drivers/net/wireless/rsi/rsi_mgmt.h:22:0,
from drivers/net/wireless/rsi/rsi_91x_core.c:17:
drivers/net/wireless/rsi/rsi_91x_core.c: In function 'rsi_dbg':
drivers/net/wireless/rsi/rsi_main.h:44:20: error: function 'rsi_dbg' can never be inlined because it uses variable argument lists
static inline void rsi_dbg(u32 zone, const char *fmt, ...)
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use pci_iounmap instead of iounmap when the virtual mapping was done
with pci_iomap. A simplified version of the semantic patch that finds this
issue is as follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
expression addr;
@@
addr = pci_iomap(...)
@rr@
expression r.addr;
@@
* iounmap(addr)
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a NULL pointer dereference in the event of an
skb allocation failure in arp_reduce().
Signed-Off-By: David L Stevens <dlstevens@us.ibm.com>
Acked-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bnx2/bnx2x rings are made up of linked pages. However there is an
upper limit on the page size as some the page size settings are 16-bit
in the hardware/firmware interface. In the current code, some parts
use BNX2_PAGE_SIZE which has a 16K upper limit and some parts use
PAGE_SIZE. On archs with >= 64K PAGE_SIZE, it generates some compile
warnings. Define a new CNIC_PAGE_SZIE which has an upper limit of
16K and use it consistently in all relevant parts.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For per device operations, cnic needs to dereference the RCU protected
cp->ulp_ops instead of the global cnic_ulp_tbl. In 2 locations,
cnic_send_nlmsg() and cnic_copy_ulp_stats(), it was referencing the
global table. If the device has been unregistered and these functions
are still being called (very unlikely scenarios), it could lead to NULL
pointer dereference.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a context modified revert of commit 6a9612e2cb
("net: cdc_ncm: remove ncm_parm field") which introduced
a NCM specification violation, causing setup errors for
some devices. These errors resulted in the device and
host disagreeing about shared settings, with complete
failure to communicate as the end result.
The NCM specification require that many of the NCM specific
control reuests are sent only while the NCM Data Interface
is in alternate setting 0. Reverting the commit ensures that
we follow this requirement.
Fixes: 6a9612e2cb ("net: cdc_ncm: remove ncm_parm field")
Reported-and-tested-by: Pasi Kärkkäinen <pasik@iki.fi>
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
linux-can-next-for-3.15-20140317
Marc Kleine-Budde says:
====================
this is a pull request of three patches for net-next/master.
It consists of a patch by Oliver Hartkopp, which unifies the MTU
settings for CAN interfaces. A patch by Christopher R. Baker populates
netdev::dev_id for udev discrimination for multi interface CAN devices.
Alexander Shiyan contributes a patch for the mcp251x driver which fixes
the regulators operation if CONFIG_REGULATOR is not enabled.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In generic, after an assignment, we use ';' instead of ','.
Although, it won't hurt.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current firmware advertises support for uAPSD, but
critical bugs force us to disable the feature.
When a fixed firmware will be available, we will be able to
re-enable uAPSD.
Cc: <stable@vger.kernel.org> [3.13+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If the low-latency update is called but there's no change then
ignore the update instead of triggering all the required work.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In case of system low latency configure passive scan to be fragmented.
Set the following scan parameters for both immediate and scheduled scan:
- passive scan fragment duration = 20ms
- out-of-channel time = 70ms
- suspend time = 105ms
Restructure channel's active/passive dwell time configuration to better
suit the above change.
The idea is that under low latency traffic passive scan is fragmented,
i.e. that dwell on a particular channel will be fragmented. Each
fragment dwell time is 20ms and fragments period is 105ms. Skipping to
next channel will be delayed by the same period (105ms). So suspend_time
parameter describing both fragments and channels skipping periods is set
to 105ms. This value is chosen so that overall passive scan duration
will not be too long. Max_out_time in this case is set to 70ms, so for
active scanning operating channel will be left for 70ms while for
passive still for 20ms (fragment dwell).
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Some scan parameters should be dependent on traffic conditions.
Centralize conditions verification in one function and obtain
scan max out-of-channel and suspend time in that new function.
Rely on bound interfaces indication instead of association state
to calculate scan parameters. If no bound interfaces use default
values for out-of-channel and suspend time parameters.
Additionally, get rid of NL80211_SCAN_FLAG_LOW_PRIORITY checks
since no use case for this exists so far.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
[reword commit log a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
