AR934x v1.3 no longer needs the DCU backoff reduction workaround for
preventing rx overruns, but in turn needs the number of usable Tx
buffers to be reduced slightly.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a local bus timeout has been detected, the host interface needs to be
reset to clear the errors. AR934x uses a different synchronous interrupt
bit to indicate this, so the check needs to be fixed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not subtract spur power from noise floor on this chip, as it can lead
to packet loss and other connectivity issues.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Unfortunately, advertising P2P_DEVICE support was a little
premature, a number of issues came up in testing and have
been fixed for 3.10. Rather than try to backport all the
different fixes, disable P2P_DEVICE support in the drivers
using it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Unfortunately, advertising P2P_DEVICE support was a little
premature, a number of issues came up in testing and have
been fixed for 3.10. Rather than try to backport all the
different fixes, disable P2P_DEVICE support in the drivers
using it. For iwlmvm that implies disabling P2P completely
as it can't support P2P operation w/o P2P Device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
set the owner of platform_driver, to ensure that the
caller of driver holds a module refernece
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some of the key differences between SD8897 and older chipsets
are as follows:
a) sdio mpa_rx and mpa_tx ports have been increased from 16 to 32
b) Same is the case with read/write bitmap that one receives from
mpa_reg read
c) aggregation packet count doubled from 8 to 16
d) Most of key reg addresses are changed
e) There is a separate command or control port
f) Now command rx/tx_done have new interrupts
1. 'supports_sdio_new_mode' flag is added to handle (a) and (b).
2. (c) and (d) are taken care of by filling chip specific
information in global structurei (mwifiex_sdio_sd8897).
3. For older chipsets, port 0 was cmd port and port 1->15 were
data port. Therefore we had CTRL_PORT_MASK to differentiate
port type. Now these changes are under 'has_control_mask' flag.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are some macros defined for multiport aggregation
calculations. As we may need to add some more code to
accomodate new chipsets, we will change them to inline
functions. Also, use dynamic allocation for Rx buffer array.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As Multiple-Port Aggregation base address value is fixed, we can
have a macro for it.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Get rid of 'if else' usage by returning in 'if' block.
This improves readability by removing indentations.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some u32 variables in sdio.c are used to store/pass u8 values.
Replace them with u8 variables.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Register addresses, firmware name and some macros are specific to
a chip. They are stored in a new structure.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently supported SDIO chipsets (SD87XX) have 16 ports.
This change is a prerequisite for new chipset.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
User can provide a text file containing calibration data in hex
format while loading mwifiex module. It will be downloaded to
firmware.
eg. insmod mwifiex.ko cal_data_cfg=cal_data.conf
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We see this WARN_ON during PCIe unload:
WARNING: at kernel/smp.c:382 smp_call_function_many+0x66/0x1e1()
This happens because we are doing PCI iounmap operations while
holding spinlock via spin_lock_irqsave(). Holding spinlock this
way causes disabling IRQs and hence PCI iounmap shows warning on
irqs_disabled() check.
Use non-irq variant of spin_lock i.e. spin_lock() instead.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds cfg80211 del_station handler for mwifiex.
If bss is not started or there are no stations in associated
stations list, no action is taken. If argument received is
null/broadcast mac, all stations in associated station list are
deauthenticated.
Patch also deletes related RxReorder stream and TxBA stream tables
for related station.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During deleting a station entry from associated sta_list, we are
supposed to delete entry only for this particular mac address.
This patch is a bug fix wherein we were deleting all entries from
list; fix this by removing list_for_each_entry_safe() call.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A full-channel scan is split to multiple scan commands in driver
before they are sent to firmware. When each scan result is back
the SSID entries are parsed and informed to cfg80211 directly.
It's observed that sometimes userspace may initiate association
as soon as the target AP is found. During the 4-way handshake
firmware may go off-channel to scan the remaining channels.
This causes the 4-way handshake to fail.
Fix it by checking 'scan_block' flag and aborting the remaining
scan in this case. 'scan_block' flag is set after association
and before 4-way handshake. It gets cleared after 4-way handshake
is completed.
Tested-by: Jason Abele <jabele@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As the variable is used only for preparation of internal scan
commands, we don't need to keep it allocated until the entire
scan completes. We will define it as a local variable and free
immediately after it's use.
New flag 'scan_aborting' is added to handle race between
mwifiex_close() and scan handler. Previously user_scan_cfg
pointer used to take care of this.
This patch fixes a memory leak in mwifiex_cfg80211_scan after
running "iwlist mlan0 scan & sleep 1; rmmod mwifiex_sdio".
Reported-by: Daniel Drake <dsd@laptop.org>
Tested-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Return from scan delay timer routine if surprise_removed flag
is true. Also, cancel the timer in unload path.
This fixes a crash when scan delay timer accesses structures
that have been freed already.
Tested with "iwlist mlan0 scan & sleep 1; rmmod mwifiex_sdio"
Reported-by: Daniel Drake <dsd@laptop.org>
Tested-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have two different static routines with name
mwifiex_free_adapter(). The routine in main.c actually frees the
adapter structure.
We will rename other routine in init.c to mwifiex_adapter_cleanup()
to avoid confusion.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Packet drop may be caused by various flows, like disconnect
while Tx packets was queued; this should not lead to stopping
of the Tx queue, or all Tx get stalled.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- Introduce common code for Tx/Rx descriptor physical address set/parse
- Fix endianness for address fields
- consistent descriptor naming: '_d' for non-cached memory, 'd' for cached copy
- wil_tx_desc_map now modify cached copy, no need for 'volatile'
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce NAPI for Rx and Tx completion.
This fixes packet reordering that happens when Rx handled right in
the IRQ: netif_rx puts packet in 'percpu' queue, then network stack
fetches packets from 'percpu' queues for processing, with different
pattern of queue switching. As result, network stack see packets
in different order. This causes hard to understand TCP throughput
degradation in about 30min
Complete polling if only one packet was processed - this eliminates
empty polls that would be otherwise done at the end of each burst
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If Rx descriptor contains garbage, it is possible to access memory beyond
allocated buffer.
Check this condition and drop Rx if reported length is
unreasonable large
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hardware uses little endian for the Tx/Rx descriptors field 'length',
do appropriate conversions
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Chun-Yeow and Javier Lopez contributed these changes to
make mesh mode use the more similar AP beaconing mode and
queue parameters. Should improve PS performance, interface
concurrency (AP modes can coexist), and beacon interval
stability.
AR9271 (ath9k_htc) mesh interfaces also need to be in AP
operating mode.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Advertise support for management frame protection in hardware.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
More specifically, enable AP-style beaconing on mesh
ifaces and change the hw capabilities to reflect mesh
support.
Coexistence with a virtual STA interface was tested as
working fine.
Signed-off-by: Javier Cardona <javier@cozybit.com>
[rebase, add iface combinations]
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was added during the early conversion of ampdu_action
to a sleeping callback. There is no need to do this - instead,
use the normal mutex that is acquired for all callbacks.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This option has not been enabled by default in any
distribution, has never been enabled in OpenWrt and no developer
has asked for this information in a bug report.
Dumping pages of random values doesn't help debugging,
remove this option (along with the vmalloc() abuse).
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only do it after the queues are allocated. This
will allow to use the 'rt2x00dev->bcn->limit'
instead of 'rt2x00dev->ops->bcn->entry_num'.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The beacon data queue is initialized already when
the rt2800_clear_beacon_register() function is called.
Fetch the size of the TXWI descriptor from that
instead of using the winfo_size field of the data
queue descriptor.
The two values are the same, and the use of the
rt2x00dev->bcn->winfo_size value allows us to
get rid of a superfluous pointer dereference.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The RX data queue is initialized already when
the rt2800_usb_enable_radio() function is called.
Fetch the number of the queue entries from that
instead of using the entry_num field of the data
queue descriptor.
The two values are the same, and the use of the
rt2x00dev->rx->limit value allows us to get rid
of a superfluous pointer dereference.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX data queue is initialized already when
the rt2800pci_txstatus_interrupt() function is
called.
Fetch the number of the queue entries from that
instead of using the entry_num field of the data
queue descriptor.
The two values are the same, and the use of the
rt2x00dev->tx->limit value allows us to get rid
of a superfluous pointer dereference.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX data queue is initialized already when
the rt61pci_txdone() function is called.
Fetch the number of the queue entries from that
instead of using the entry_num field of the data
queue descriptor.
The two values are the same, and the use of the
rt2x00dev->tx->limit value allows us to get rid
of a superfluous pointer dereference.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX data queue is initialized already when
the rt2x00lib_probe_hw() function is called.
Fetch the number of the queue entries from that
instead of using the entry_num field of the data
queue descriptor.
The two values are the same, and the use of the
rt2x00dev->tx->limit value allows us to get rid
of a superfluous pointer dereference.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was an extra ';' character added to the end of the if statement
which means that it always prints that the /proc entry wasn't created
even though it was.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Waiting for all subframes of an existing aggregation session to drain
before allowing mac80211 to start a new one is fragile and deadlocks
caused by this behavior have been observed.
Since mac80211 has proper synchronization for aggregation session
start/stop handling, a better approach to session handling is to simply
allow mac80211 to start a new session at any time. This requires
changing the code to discard any packets outside of the BlockAck window
in the A-MPDU software retry code.
This patch implements the above and also simplifies the code.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After a tx attempt, an A-MPDU subframe can still have fi->retries at 0
(if the retry count wasn't incremented due to powersave).
In that case it is still tracked as part of the block ack window, so
when draining the tid queue, its sequence number needs to be cleared
from the pending frame bitmap.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes some issues introduced in the rate control API rework.
When not running aggregation, copy bf->rates into info->control.rates
before applying the rate control status to it.
In ath_lookup_rate, the rates need to be pulled from bf->rates, not the
tx info.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When aggregation stop is requested, don't run the mac80211 aggregation
stop callback yet, while the session is still blocked.
Also, when aggregation flush is requested, don't run the callback at all.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
