The function s5p_mfc_reload_firmware is exactly same as
s5p_mfc_load_firmware. So removing the duplicate function.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
X-Patchwork-Delegate: mchehab@redhat.com
The driver mistakenly prints the ROM version instead of the device ID to
the kernel log when detecting the chip. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
X-Patchwork-Delegate: mchehab@redhat.com
Remove the CONFIG_ prefix from two Kconfig symbols in a dependency for
SMS_SIANO_DEBUGFS. This prefix is invalid inside Kconfig files.
Note that the current (common sense) dependency on SMS_USB_DRV and
SMS_SDIO_DRV being equal ensures that SMS_SIANO_DEBUGFS will not
violate its constraints. These constraint are that:
- it should only be built if SMS_USB_DRV is set;
- it can't be builtin if USB support is modular.
So drop the dependency on SMS_USB_DRV, as it is unneeded.
Fixes: 6c84b21428 ("[media] sms: fix randconfig building error")
Reported-by: Martin Walch <walch.martin@web.de>
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Conflicts:
drivers/infiniband/hw/cxgb4/device.c
The cxgb4 conflict was simply overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
* .: (268 commits)
Linux 3.16-rc6
um: segv: Save regs only in case of a kernel mode fault
um: Fix hung task in fix_range_common()
um: Ensure that a stub page cannot get unmapped
Revert "um: Fix wait_stub_done() error handling"
btrfs: test for valid bdev before kobj removal in btrfs_rm_device
Btrfs: fix abnormal long waiting in fsync
random: check for increase of entropy_count because of signed conversion
ARM: EXYNOS: Fix core ID used by platsmp and hotplug code
ahci: add support for the Promise FastTrak TX8660 SATA HBA (ahci mode)
ARM: at91/dt: add missing clocks property to pwm node in sam9x5.dtsi
ARM: at91/dt: fix usb0 clocks definition in sam9n12 dtsi
ARM: at91: at91sam9x5: correct typo error for ohci clock
irqchip: gic: Fix core ID calculation when topology is read from DT
GFS2: fs/gfs2/rgrp.c: kernel-doc warning fixes
GFS2: memcontrol: Spelling s/invlidate/invalidate/
GFS2: Allow caching of glocks for flock
GFS2: Allow flocks to use normal glock dq rather than dq_wait
GFS2: replace count*size kzalloc by kcalloc
GFS2: Use GFP_NOFS when allocating glocks
...
Conflicts:
drivers/media/dvb-frontends/si2168.c
drivers/media/dvb-frontends/si2168_priv.h
drivers/media/tuners/si2157.c
As reported by Kbuildtest:
drivers/media/v4l2-core/v4l2-subdev.c: In function 'check_format':
drivers/media/v4l2-core/v4l2-subdev.c:136:23: error: 'struct v4l2_subdev' has no member named 'entity'
if (format->pad >= sd->entity.num_pads)
^
drivers/media/v4l2-core/v4l2-subdev.c: In function 'check_crop':
drivers/media/v4l2-core/v4l2-subdev.c:148:21: error: 'struct v4l2_subdev' has no member named 'entity'
if (crop->pad >= sd->entity.num_pads)
^
drivers/media/v4l2-core/v4l2-subdev.c: In function 'check_selection':
drivers/media/v4l2-core/v4l2-subdev.c:161:20: error: 'struct v4l2_subdev' has no member named 'entity'
if (sel->pad >= sd->entity.num_pads)
^
drivers/media/v4l2-core/v4l2-subdev.c: In function 'check_edid':
drivers/media/v4l2-core/v4l2-subdev.c:169:21: error: 'struct v4l2_subdev' has no member named 'entity'
if (edid->pad >= sd->entity.num_pads)
^
drivers/media/v4l2-core/v4l2-subdev.c: In function 'subdev_do_ioctl':
>> drivers/media/v4l2-core/v4l2-subdev.c:186:6: warning: unused variable 'rval' [-Wunused-variable]
int rval;
^
drivers/media/v4l2-core/v4l2-subdev.c: At top level:
drivers/media/v4l2-core/v4l2-subdev.c:129:12: warning: 'check_format' defined but not used [-Wunused-function]
static int check_format(struct v4l2_subdev *sd,
^
drivers/media/v4l2-core/v4l2-subdev.c:142:12: warning: 'check_crop' defined but not used [-Wunused-function]
static int check_crop(struct v4l2_subdev *sd, struct v4l2_subdev_crop *crop)
^
drivers/media/v4l2-core/v4l2-subdev.c:154:12: warning: 'check_selection' defined but not used [-Wunused-function]
static int check_selection(struct v4l2_subdev *sd,
^
drivers/media/v4l2-core/v4l2-subdev.c:167:12: warning: 'check_edid' defined but not used [-Wunused-function]
static int check_edid(struct v4l2_subdev *sd, struct v4l2_subdev_edid *edid)
The above warnins happen because those functions are used only
when the V4L2 subdev API is enabled.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
MEDIA_SDR_SUPPORT and I2C_MUX are needed for rtl2832_sdr.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Commit 0ba2aeb6da
(v4l2-ctrls: increase internal min/max/step/def to 64 bit)
changes v4l2 controls to 64-bit. Driver it not working on 32-bit
arch as it uses directly control 'step' which is changed to 64-bit.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/built-in.o: In function `isp_video_open':
/src/linux/drivers/media/platform/omap3isp/ispvideo.c:1253: undefined reference to `vb2_dma_contig_memops'
drivers/built-in.o: In function `omap3isp_video_init':
/src/linux/drivers/media/platform/omap3isp/ispvideo.c:1344: undefined reference to `vb2_dma_contig_init_ctx'
/src/linux/drivers/media/platform/omap3isp/ispvideo.c:1350: undefined reference to `vb2_dma_contig_cleanup_ctx'
drivers/built-in.o: In function `omap3isp_video_cleanup':
/src/linux/drivers/media/platform/omap3isp/ispvideo.c:1381: undefined reference to `vb2_dma_contig_cleanup_ctx'
make: *** [vmlinux] Error 1
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This switches all register accesses to use regmap. It allows to
use the regmap cache, tracing, and debug register dump facilities,
and removes the need to open code read-modify-writes.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Since (min_row_time - crop->width) can be negative, we have to do a signed
comparison here. Otherwise max_t casts the negative value to unsigned int
and sets min_hblank to that invalid value.
Cc: stable@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Regression fix:
V4L2_PIX_FMT_PRIV_MAGIC should only be set for the VIDEO_CAPTURE and
VIDEO_OUTPUT buffer types, and not for any others. In the case of
the win format this overwrote a pointer value that is passed in from
userspace.
Just set it for V4L2_BUF_TYPE_VIDEO_CAPTURE and OUTPUT only. Set
it before the callback is called, just as is done for try/s_fmt, and
again afterwards in case the driver zeroed it. The latter was missing
in try/s_fmt, so add it there as well. Currently it is quite likely
that drivers clear priv (that was needed for a long time), so it makes
sense to set it twice.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
V4L2_CAP_EXT_PIX_FORMAT is set for capabilities, but it needs to be set for
device_caps as well: device_caps should report all caps relevant to the
device node, and this is one of them.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If you have a maximum that is at the limit of what the type supports,
and the step is > 1, then you can get wrap-around errors since the
code assumes that the maximum that the type supports is
ctrl->maximum + ctrl->step / 2.
In practice this is always fine, but in artificially crafted ranges
you will hit this bug. Since this is core code it should just work.
This bug has always been there but since it doesn't cause problems in
practice it was never noticed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The original report from Nikhil was that if data_offset > 0 and bytesused == 0,
then the check in __verify_length() would fail, even though the spec says that
if bytes_used == 0, then it will be replaced by the actual length of the
buffer.
After digging into it a bit more I realized that there were several other
things wrong:
- in __verify_length() it would use the application-provided length value
for USERPTR and the vb2 core length for other memory models, but it
should have used the application-provided length as well for DMABUF.
- in __fill_vb2_buffer() on the other hand it would replace bytesused == 0
by the application-provided length, even for MMAP buffers where the
length is determined by the vb2 core.
- in __fill_vb2_buffer() it tries to figure out if all the planes have
bytesused == 0 before it will decide to replace bytesused by length.
However, the spec makes no such provision, and it makes for convoluted
code. So just replace any bytesused == 0 by the proper length.
The idea behind this was that you could use bytesused to signal empty
planes, something that is currently not supported. But that is better
done in the future by using one of the reserved fields in strucy v4l2_plane.
This patch fixes all these issues.
Regards,
Hans
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Cc: Nikhil Devshatwar <nikhil.nd@ti.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fill FMT buffer size field in order to inform app which will be
used streaming buffer size. Currently driver doesn't allow buffer
size value proposed by application.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
SDR API is very new and surprises may occur. Due to that print
notice to remind possible users.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move msi3101 out of staging and rename to msi2500.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fill FMT buffer size field in order to inform app which will be
used streaming buffer size. Currently driver doesn't allow buffer
size value proposed by application.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fill FMT buffer size field in order to inform app which will be
used streaming buffer size. Currently driver doesn't allow buffer
size value proposed by application.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is needed for PCTV 522e support.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is needed for PCTV 522e support.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Modify all users of si2157_config to correctly initialize all not
listed values to 0.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Modify all users of si2157_config to correctly initialize all not
listed values to 0.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The struct prototype is defined at the beginning of the code as
"si2157_ops" but the real struct is called "si2157_tuner_ops".
This is causing the name to be empty on this info msg: si2157 16-0060:
si2157: found a '' in cold state
[crope@iki.fi: commit msg from Luis email reply]
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Cc: Luis Alves <ljalvs@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Testing demod presence on probe fails if the demod was sleep mode.
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In case of failure the return value was always 0. Return proper
error code (ENODEV) instead.
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Improve scanning performance by setting property 0301 with a value
from Windows driver.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds symbol rate setting to the driver.
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Print notice on driver load: "SDR API is still slightly
experimental and functionality changes may follow". It is just
remind possible used SDR API is very new and surprises may occur.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move it out of staging into media like all the other SDR drivers
too. There is no good reasons to keep these SDR drivers in staging.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
SDR API is very new and surprises may occur. Due to that print
notice to remind possible users.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move emulated format behind module parameter as those are not
supported. Format conversions will be on library eventually.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
