We should only write the DDI_BUF_CTL at this point for HDMI/DVI. For
DP we need to do this earlier, and the values written to the register
are also different.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The old rule that the AUX registers are just an offset (+4 and +10)
from output_reg is not true anymore, since output_reg in on the CPU
and some AUX regs are on the PCH.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: use the existing #defines as spotted by Damien Lespiau.]
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some BIOSes may forcibly suspend RC6 during their operation which
trigger a warning as we find the hardware in a perplexing state upon
first use. So far that appears to be the worst symptom as fortuituously
we use the same values as the BIOS for programming the FORCEWAKE register.
Reported-by: Oleksij Rempel <bug-track@fisher-privat.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We now no longer rely on this.
This is step 1 on a long journey to rid us of the save/restore
madness, which tends to lightly paper over many issues, and cause
tons of bad things itself ...
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: satisfy Paulo's ocd and drop the needless braces.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... instead of relying on the register save/restore madness to do this.
To extract a bit of code call drm_mode_config_reset both on resume
and boot-up and move the hw state frobbing from the crt_init to the
->reset callback. The crt connector is the only one with a ->reset
callback, hence we can easily do this.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... since they don't apply to pre-pch platforms and could actually be
harmful.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We already do that as part of the ringbuffer re-setup at resume time.
Furthermore the register offset has moved on gen6+ around quite a bit,
and on ilk/gm45 we also need to restore the HWS reg for the bsd ring,
not just the render ring.
So again in kms mode this is only confusing a best, hence don't
bother.
v2: Fixup logic, noticed by Paulo Zanoni.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We already call drm_irq_install/uninstall at the right time, which
will set up the irq registers with the correct values (through the
preinstall hooks).
For kms this is at best harmless, in the worst case we get an
interrupt when we don't really expect it.
v2: Fixup the logic, noticed by Paulo Zanoni.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We completely compute these anew in each modeset, hence we don't rely
on them containing anything valid after resume.
To avoid breaking any ums setup due to reordering of the reads/writes
simply don't reorder anything, but bracket the reads/writes into if
(!kms) conditionals. More churn, but safer.
v2: Fixup the logic, noticed by Paulo Zanoni.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Previously, the DP register was used for everything. On Haswell, it
was split into DDI_BUF_CTL (which is the new intel_dp->DP register)
and DP_TP_CTL.
The logic behind this patch is based on a patch written by Shobhit
Kumar, but the way the code was written is very different.
Credits-to: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Fixup the logic error spotted by Jani Nikula.]
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In theory, all the DDI pipe settings should be set here, including
timing and M/N registers. For now, let's just set the DP MSA
attributes.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: fixed up the unused typo in a #define, spotted by Jani
Nikula.]
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On the worst scenario, users with new hardwares and old kernel from
enabling times can get black screens. So, from now on, this
perliminary_hw_support module parameter shall be used by all upcoming
platforms that are still under enabling. The second option would be to
merge the pci ids after basic modeset works, but that makes testing
and development while bringing up hw a rather tedious afair.
Although it is uncomfortable for developers use this extra variable it
brings more stability for end users.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
[danvet: dropped the i915_ param prefix, i915.i915_ is just tedious.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the introduction of per-process GTT space, the hardware designers
thought it wise to also limit the ability to write to MMIO space to only
a "secure" batch buffer. The ability to rewrite registers is the only
way to program the hardware to perform certain operations like scanline
waits (required for tear-free windowed updates). So we either have a
choice of adding an interface to perform those synchronized updates
inside the kernel, or we permit certain processes the ability to write
to the "safe" registers from within its command stream. This patch
exposes the ability to submit a SECURE batch buffer to
DRM_ROOT_ONLY|DRM_MASTER processes.
v2: Haswell split up bit8 into a ppgtt bit (still bit8) and a security
bit (bit 13, accidentally not set). Also add a comment explaining why
secure batches need a global gtt binding.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
[danvet: added hsw fixup.]
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Somehow this was left out in the refactoring that introduced the pch
handlers. Avoids a hotplug_mask special case in the ilk_irq_handler.
Noticed while hunting down the pch hotplug bits.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 2477367083.
If (for whatever reason) the DP sink device never asks for the maximal
voltage level, we never don't hit the check that should bail us out
after 5 retries of the same voltage. Which leads to an endless loop in
the DP link training code, which hangs the driver.
Now some more DP link training experiments on eDP panels seem to
indicate that our training algorithm isn't robust enough anyway and
needs more work. Hence for 3.7-fixes, let's just revert the regressing
commit instead of trying to apply more duct-tape.
Reported-by: Oleksij Rempel <bug-track@fisher-privat.net>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For TV and LVDS encoders intel_sdvo_set_input_timings_for_mode()
is called to pass a mode to the sdvo chip and retrieve a dtd
containing information needed to calculate the adjusted_mode which
is done by intel_sdvo_get_dtd_from_mode().
To set this adjusted_mode as input mode for the sdvo chip, a dtd is
recalculated using intel_sdvo_get_mode_from_dtd(). During this round
trip the sdvo_flags contained in the dtd obtained from the hardware
are lost.
Since these flags cannot be ignored in all cases this patch preserves
and restores them.
This regression has been introduced in
commit 6651819b4b
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun Apr 1 19:16:18 2012 +0200
drm/i915: handle input/output sdvo timings separately in mode_set
Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
SDVO LVDS are not clonable as the input mode gets adjusted by
the LVDS encoder.
Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
NCR machines with LVDS panels using Intel chipsets need to have the
QUIRK_INVERT_BRIGHTNESS bit set.
Unfortunately NCR doesn't set a meaningful subvendor/subdevice ID,
therefore we add a DMI dependent quirk list.
Signed-off-by: Egbert Eich <eich@suse.de>
[danvet: fixup whitespace fail.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The DPLL multipiler is set up in intel_display.c:i9xx_update_pll()
called from i9xx_crtc_mode_set().
There the DPLL multiplier is adjusted so that the SDVO gets a sufficient
bus clock.
When cloning a CRTC between an SDVO driven encoder and the standard
DAC the DAC setup code reseted the multiplier value to 1 thus undoing
the correct setup. There is no need to touch the multiplier in the DAC
setup code: the correct value (i.e. 1 in case no SDVO encoder is used)
is set by i9xx_update_pll() already.
A comment at the code suggested that this code is a left over from the
days when there was no setup for clone modes.
Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BIOS should be setting the minimum voltage for rc6 to be 450mV. Old or
buggy BIOSen may not be doing this, so we correct it for them. Ideally
customers should update the BIOS as only it would know the optimal
values for the platform, so we leave that fact as a DRM_ERROR for the
user to see.
Unfortunately this isn't fixing any of the issues it was targeted to
fix, but it is documented that we must do it.
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: Matt Turner <mattst88@gmail.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: bikeshedded loglevel of the "your bios is broken message" to
debug.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is a special mechanism for communicating with the PCU already
being used for the ring frequency stuff. As we'll be needing this for
other commands, extract it now to make future code less error prone and
the current code more reusable.
I'm not entirely sure if this code matches 1:1 with the previous code
behaviorally. Functionally however, it should be the same.
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Fixup compile fail reported by Wu Fengguang.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
minor set of nouveau fixes.
* 'drm-nouveau-fixes' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/bios: fix typo in error message
drm/nouveau: only call ttm_agp_tt_create when __OS_HAS_AGP
drm/nv50/fb: fix double free of vram mm
drm/nouveau/pm: do not stop reclocking if failing to set the fan speed
drm/nouveau/pm: fix a typo related to the move to the therm subdev
drm/nouveau/hwmon: fix the initialization condition
ttm_agp_tt_create is itself defined under CONFIG_AGP, so there's no
point calling it otherwise.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
With the introduction of fan management modes, fan may not be drivable.
We should allow reclocking nonetheless.
This return was stupid to begin with since it may have left the card
in an intermediate state (clocks corresponding to a perflvl and voltage
corresponding to another one). The reclocking code will need to be
rewritten in a near-future in order to provide a better error handling.
Reported-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Martin Peres <martin.peres@labri.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
drivers/gpu/drm/radeon/radeon_atpx_handler.c:151:3: warning: format '%lu' expects type 'long unsigned int', but argument 2 has type 'size_t'
[airlied: Alex had others fixed already, except for atpx one]
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex writes:
"This is the first -fixes pull for 3.7. I would have preferred
to have gotten it out a bit sooner, but I was on holiday last week.
- Cleanup of the new 2 level page table code it get it in
better shape and using less memory.
- Fix some display issues related to the PLL rework.
- Fix some cmpiler warnings and errors with certain config
options.
- Other misc bug fixes."
* 'drm-fixes-3.7' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix spelling typos in debugging output
drm/radeon: Don't destroy I2C Bus Rec in radeon_ext_tmds_enc_destroy().
drm/radeon: check if pcie gen 2 is already enabled (v2)
drm/radeon/cayman: set VM max pfn at MC init
drm/radeon: separate pt alloc from lru add
drm/radeon: don't add the IB pool to all VMs v2
drm/radeon: allocate page tables on demand v4
drm/radeon: update comments to clarify VM setup (v2)
drm/radeon: allocate PPLLs from low to high
drm/radeon: fix compilation with backlight disabled
drm/radeon: use %zu for formatting size_t
Daniel writes:
"- some register magic to fix hsw crw (Paulo&Ben)
- fix backlight destruction for cpu edp (Jani)
- fix gen ch7xxx dvo ->get_hw_state
- fixup the plane->pipe fixup code, the broken version massively angers
the modeset sanity checks
- kill pipe A quirk for i855gm, otherwise I get a black screen with the
above patch
- fixup for gem_get_page helper (Chris)
- fixup guardband clipping w/a (Ken), without this mesa master can erronously
drop vertices on snb, mesa 9.0 has the optimization reverted
- another pageflip vs. modeset fix
- kill bogus BUG_ON which broke ums+gem from Willy Tarreau (gasp, people
are still using this!)"
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: fix non-DP-D eDP backlight cleanup and module reload
drm/i915: HSW CRW stability magic
drm/i915/dvo-ch7xxx: fix get_hw_state
drm/i915: fixup the plane->pipe fixup code
drm/i915: rip out the pipe A quirk for i855gm
drm/i915: disable wc gtt pte mappings on gen2
drm/i915: fixup i915_gem_object_get_page inline helper
drm/i915: Disallow preallocation of requests
drm/i915: Set guardband clipping workaround bit in the right register.
drm/i915: paper over a pipe-enable vs pageflip race
drm/i915: remove useless BUG_ON which caused a regression in 3.5.
radeon_i2c_fini() walks thru the list of I2C bus recs rdev->i2c_bus[]
to destroy each of them.
radeon_ext_tmds_enc_destroy() however also has code to destroy it's
associated I2C bus rec which has been obtained by radeon_i2c_lookup()
and is therefore also in the i2c_bus[] list.
This causes a double free resulting in a kernel panic when unloading
the radeon driver.
Removing destroy code from radeon_ext_tmds_enc_destroy() fixes this
problem.
agd5f: fix compiler warning
Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
No need to emit them at VM flush as we no longer use
variable sized page tables now that we support 2 level
page tables. This matches the behavior of SI (which
does not support variable sized page tables).
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Based on Dmitries work, but splitting the code into page
directory and page table handling makes it far more
readable and (hopefully) more reliable.
Allocations of page tables are made from the SA on demand,
that should still work fine since all page tables are of
the same size.
Also using the fact that allocations from the SA are mostly
continuously (except for end of buffer wraps and under very
high memory pressure) to group updates send to the chipset
specific code into larger chunks.
v3: mostly a rewrite of Dmitries previous patch.
v4: fix some typos and coding style
Signed-off-by: Dmitry Cherkasov <Dmitrii.Cherkasov@amd.com>
Signed-off-by: Christian König <deathsimple@vodafone.de>
Tested-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The actual set up and assignment of VM page tables
is done on the fly in radeon_gart.c.
v2: update vm size comments
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
The order shouldn't matter, but there have been problems
reported on certain older asics. This behaves more
like the original code before the PPLL allocation
rework.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Markus Trippelsdorf <markus@trippelsdorf.de>
