Pull ARM SoC driver updates from Arnd Bergmann:
"These are changes for drivers that are intimately tied to some SoC and
for some reason could not get merged through the respective subsystem
maintainer tree.
Most of the new code is for the Keystone Navigator driver, which is
new base support that is going to be needed for their hardware
accelerated network driver and other units.
Most of the commits are for moving old code around from at91 and omap
for things that are done in device drivers nowadays.
- at91: move reset, poweroff, memory and clocksource code into
drivers directories
- socfpga: add edac driver (through arm-soc, as requested by Boris)
- omap: move omap-intc code to drivers/irqchip
- sunxi: added an RTC driver for sun6i
- omap: mailbox driver related changes
- keystone: support for the "Navigator" component
- versatile: new reboot, led and soc drivers"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (92 commits)
bus: arm-ccn: Fix spurious warning message
leds: add device tree bindings for register bit LEDs
soc: add driver for the ARM RealView
power: reset: driver for the Versatile syscon reboot
leds: add a driver for syscon-based LEDs
drivers/soc: ti: fix build break with modules
MAINTAINERS: Add Keystone Multicore Navigator drivers entry
soc: ti: add Keystone Navigator DMA support
Documentation: dt: soc: add Keystone Navigator DMA bindings
soc: ti: add Keystone Navigator QMSS driver
Documentation: dt: soc: add Keystone Navigator QMSS bindings
rtc: sunxi: Depend on platforms sun4i/sun7i that actually have the rtc
rtc: sun6i: Add sun6i RTC driver
irqchip: omap-intc: remove unnecessary comments
irqchip: omap-intc: correct maximum number or MIR registers
irqchip: omap-intc: enable TURBO idle mode
irqchip: omap-intc: enable IP protection
irqchip: omap-intc: remove unnecesary of_address_to_resource() call
irqchip: omap-intc: comment style cleanup
irqchip: omap-intc: minor improvement to omap_irq_pending()
...
Pull ARM SoC DT updates from Arnd Bergmann:
"As usual, this is the largest branch, though this time a little under
half of the total changes with 307 individual non-merge changesets.
The largest changes are the addition of new machines, in particular
the Tegra based Chromebook, the Renesas r8a7794 SoC, and DT support
for the old i.MX1 platform.
Other changes include
- at91: various sam9 and sama5 updates
- exynos: much extended Peach Pi/Pit (Chromebook 2) support
- keystone: new peripherals
- meson: added DT for meson6 SoC
- mvebu: new device support for Armada 370/375
- qcom: improved support for IPQ8064 and MSM8x60
- rockchip: much improved support for rk3288
- shmobile: lots of updates all over the place
- sunxi: dts license change
- sunxi: more a23 device support
- vexpress: CLCD DT description"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (308 commits)
ARM: DTS: meson: update DTSI to add watchdog node
ARM: dts: keystone-k2l: fix mdio io start address
ARM: dts: keystone-k2e: fix mdio io start address
ARM: dts: keystone-k2e: update usb1 node for dma properties
ARM: dts: keystone: fix io range for usb_phy0
Revert "Merge tag 'hix5hd2-dt-for-3.18' of git://github.com/hisilicon/linux-hisi into next/dt"
Revert "ARM: dts: hix5hd2: add wdg node"
ARM: dts: add rk3288 i2s controller
ARM: vexpress: Add CLCD Device Tree properties
ARM: bcm2835: add I2S pinctrl to device tree
ARM: meson: documentation: add bindings documentation
ARM: meson: dts: add basic Meson/Meson6/Meson6-atv1200 DTSI/DTS
ARM: dts: mt6589: Change compatible string for GIC
ARM: dts: mediatek: Add compatible property for aquaris5
ARM: dts: mt6589-aquaris5: Add boot argument earlyprintk
ARM: dts: mt6589: Fix typo in GIC unit address
ARM: dts: Build dtb for Mediatek board
ARM: dts: keystone: fix bindings for pcie and usb clock nodes
ARM: dts: keystone: k2l: Fix chip selects for SPI devices
ARM: dts: keystone: add dsp gpio controllers nodes
...
Pull ARM SoC platform changes from Arnd Bergmann:
"New and updated SoC support. Among the things new for this release
are:
- at91: Added support for the new SAMA5D4 SoC, following the earlier
SAMA5D3
- bcm: Added support for BCM63XX family of DSL SoCs
- hisi: Added support for HiP04 server-class SoC
- meson: Initial support for the Amlogic Meson6 (aka 8726MX) platform
- shmobile: added support for new r8a7794 (R-Car E2) automotive SoC
Noteworthy changes to existing SoC support are:
- imx: convert i.MX1 to device tree
- omap: lots of power management work
- omap: base support to enable moving to standard UART driver
- shmobile: lots of progress for multiplatform support, still
ongoing"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (171 commits)
ARM: hisi: depend on ARCH_MULTI_V7
CNS3xxx: Fix debug UART.
ARM: at91: fix nommu build regression
ARM: meson: add basic support for MesonX SoCs
ARM: meson: debug: add debug UART for earlyprintk support
irq: Export handle_fasteoi_irq
ARM: mediatek: Add earlyprintk support for mt6589
ARM: hisi: Fix platmcpm compilation when ARMv6 is selected
ARM: debug: fix alphanumerical order on debug uarts
ARM: at91: document Atmel SMART compatibles
ARM: at91: add sama5d4 support to sama5_defconfig
ARM: at91: dt: add device tree file for SAMA5D4ek board
ARM: at91: dt: add device tree file for SAMA5D4 SoC
ARM: at91: SAMA5D4 SoC detection code and low level routines
ARM: at91: introduce basic SAMA5D4 support
clk: at91: add a driver for the h32mx clock
ARM: pxa3xx: provide specific platform_devices for all ssp ports
ARM: pxa: ssp: provide platform_device_id for PXA3xx
ARM: OMAP4+: Remove static iotable mappings for SRAM
ARM: OMAP4+: Move SRAM data to DT
...
Pull ARM SoC cleanups from Arnd Bergmann:
"This time around, the cleanup branch contains mostly code removal. A
number of board files for at91, imx and msm have become obsolete
because of the DT conversion and are now ready to be removed. The
OMAP platform has traditionally had its own DMA engine abstraction and
as this is being phased out, a lot of the original code is now unused
and can be removed as well.
S3C24xx can be simplified now that the restart code is a proper device
driver.
Finally, a number of cleanups in shmobile are done to prepare for the
addition of new code in other branches"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
ARM: at91: Remove the support for the RSI EWS board
arm: mach-omap2: Convert pr_warning to pr_warn
ARM: OMAP: Remove unused pieces of legacy DMA API
ARM: at91: remove board file for Acme Systems Fox G20
ARM: orion5x: Convert pr_warning to pr_warn
ARM: S3C24XX: remove separate restart code
ARM: EXYNOS: Do not calculate boot address twice
ARM: sunxi: Remove sun4i reboot code from mach directory
ARM: imx: Remove mach-mxt_td60 board file
ARM: shmobile: armadillo800eva legacy: Use rmobile_add_devices_to_domains()
ARM: shmobile: r8a7740: Clean up pm domain table
ARM: shmobile: r8a7740: Use rmobile_add_devices_to_domains()
ARM: shmobile: sh7372: Make domain_devices[] static __initdata
ARM: shmobile: mackerel: Make domain_devices[] static __initdata
clocksource: tcb_clksrc: sanitize IRQ request
ARM: at91/tclib: mask interruptions at shutdown and probe
ARM: at91/tclib: move initialization from alloc to probe
ARM: at91/tclib: prefer using of devm_* functions
ARM: clps711x: Switch CLPS711X subarch to use clk and clocksource driver
ARM: shmobile: r8a7791 is now called "R-Car M2-W"
...
Pull ARM SoC non-critical bug fixes from Arnd Bergmann:
"These are bug fixes for harmless problems that were not important
enough to get fixed in 3.17. The majority of these are OMAP specific,
but there are also a couple for Marvell mvebu, cns3xxx, and others, as
well as some updates for the MAINTAINERS file.
In particular, Robert Jarzmik and Daniel Mack now volunteered to help
out maintaining the PXA platform, Krzysztof Halasa took over the
cns3xxx platform, Carlo Caione is the maintainer for the new Amlogic
meson platform, and Matthias Brugger is now listed for the mediatek
platform he recently contributed"
* tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (42 commits)
MAINTAINERS: update Shawn's email address
MAINTAINERS: condense some Tegra related entries
MAINTAINERS: add Alexandre Courbot for Tegra
MAINTAINERS: CNS3xxx and IXP4xx update.
MAINTAINERS: Add maintainers entry for Mediatek SoCs
arm, vt8500, LLVMLlinux: Use mcr instead of mcr% for mach-vt8500
MAINTAINERS: add a third maintainer to mach-bcm
CNS3xxx: Fix PCIe read size limit.
CNS3xxx: Fix logical PCIe topology.
CNS3xxx: Fix debug UART.
MAINTAINERS: Add entry for the Amlogic MesonX SoCs
MAINTAINERS: update ARM pxa maintainers
ARM: at91/PMC: don't forget to write PMC_PCDR register to disable clocks
ARM: at91: fix at91sam9263ek DT mmc pinmuxing settings
ARM: mvebu: Netgear RN102: Use Hardware BCH ECC
ARM: Kirkwood: Fix DT based DSA.
ARM: OMAP2+: make of_device_ids const
ARM: omap2: make arrays containing machine compatible strings const
ARM: LPC32xx: Fix reset function
ARM: mvebu: Netgear RN2120: Use Hardware BCH ECC
...
Pull tty/serial driver updates from Greg KH:
"Here's the big tty/serial driver patchset for 3.18-rc1.
Lots of little things in here, some good work from Peter Hurley on the
tty core, and in lots of drivers. There are also lots of other driver
updates in here as well, full details in the changelogs.
All have been in the linux-next tree for a while"
* tag 'tty-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (99 commits)
Revert "serial/core: Initialize the console pm state"
tty: serial: 8250: use 32bit variable for rpm_tx_active
tty: serial: msm: Add earlycon support
serial/core: Initialize the console pm state
serial: asc: Conditionally use readl_relaxed (COMPILE_TEST)
serial: of-serial: add PM suspend/resume support
m68k: AMIGA_BUILTIN_SERIAL should depend on TTY
asm/uapi: Add definition of TIOC[SG]RS485
tty/metag_da: Add console_poll module parameter
serial: 8250_pci: remove rts_n override from Baytrail quirk
serial: cadence: Add generic earlycon support
serial: imx: change the wait even to interruptiable
serial: imx: terminate the RX DMA when the UART is suspending
serial: imx: fix throttle/unthrottle callbacks for hardware assisted flow control
serial: 8250: Add Quark X1000 to 8250_pci.c
tty: omap-serial: pull out calculation from baud_is_mode16
tty: omap-serial: fix division by zero
xen_hvc: no reason to write the type key on xenstore
tty: serial: 8250_core: remove UART_IER_RDI in serial8250_stop_rx()
tty: serial: 8250_core: use the ->line argument as a hint in serial8250_find_match_or_unused()
...
Pull m68k updates from Geert Uytterhoeven:
"Summary:
- a fix for an intermittent crash in macsonic and hilkbd, marked for
stable,
- build fixes for uncommon configs.
Note: "m68k: AMIGA_BUILTIN_SERIAL should depend on TTY" was also
picked up by GregKH for his TTY/Serial patches tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Reformat arch/m68k/mm/hwtest.c
m68k: Disable/restore interrupts in hwreg_present()/hwreg_write()
m68k: AMIGA_BUILTIN_SERIAL should depend on TTY
m68k: Add missing ioport_unmap()
m68k/atari - stram: Add missing #include <linux/ioport.h>
Pull S+core updates from Lennox Wu:
"Three of the patches are for building allmodconfig, and the others are
for removing useless flags"
* tag 'for-linus-20141006' of git://github.com/sctscore/linux-off:
score: Remove GENERIC_HAS_IOMAP
arch/score/include/asm/Kbuild: Add generic "serial.h"
score: remove deprecated IRQF_DISABLED
arch/score/mm/cache.c: Export 'flush_icache_range'
arch: score: Export necessary symbols in related files
Pull arch/tile updates from Chris Metcalf:
"The only substantive pieces in this batch are some more vDSO support,
and removing the reference to &platform_bus in tile-srom.c.
The rest are minor issues reported to me"
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: add clock_gettime support to vDSO
tile: switch to using seqlocks for the vDSO time code
tile gxio: use better string copy primitive
char: tile-srom: Add real platform bus parent
Removed repeated word in comments
tilegx: Enable ARCH_SUPPORTS_ATOMIC_RMW
tile: Remove tile-specific _sinitdata and _einitdata
tile: use ARRAY_SIZE
Pull arm64 updates from Catalin Marinas:
- eBPF JIT compiler for arm64
- CPU suspend backend for PSCI (firmware interface) with standard idle
states defined in DT (generic idle driver to be merged via a
different tree)
- Support for CONFIG_DEBUG_SET_MODULE_RONX
- Support for unmapped cpu-release-addr (outside kernel linear mapping)
- set_arch_dma_coherent_ops() implemented and bus notifiers removed
- EFI_STUB improvements when base of DRAM is occupied
- Typos in KGDB macros
- Clean-up to (partially) allow kernel building with LLVM
- Other clean-ups (extern keyword, phys_addr_t usage)
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (51 commits)
arm64: Remove unneeded extern keyword
ARM64: make of_device_ids const
arm64: Use phys_addr_t type for physical address
aarch64: filter $x from kallsyms
arm64: Use DMA_ERROR_CODE to denote failed allocation
arm64: Fix typos in KGDB macros
arm64: insn: Add return statements after BUG_ON()
arm64: debug: don't re-enable debug exceptions on return from el1_dbg
Revert "arm64: dmi: Add SMBIOS/DMI support"
arm64: Implement set_arch_dma_coherent_ops() to replace bus notifiers
of: amba: use of_dma_configure for AMBA devices
arm64: dmi: Add SMBIOS/DMI support
arm64: Correct ftrace calls to aarch64_insn_gen_branch_imm()
arm64:mm: initialize max_mapnr using function set_max_mapnr
setup: Move unmask of async interrupts after possible earlycon setup
arm64: LLVMLinux: Fix inline arm64 assembly for use with clang
arm64: pageattr: Correctly adjust unaligned start addresses
net: bpf: arm64: fix module memory leak when JIT image build fails
arm64: add PSCI CPU_SUSPEND based cpu_suspend support
arm64: kernel: introduce cpu_init_idle CPU operation
...
Pull ARM updates from Russell King:
"Included in these updates are:
- Performance optimisation to avoid writing the control register at
every exception.
- Use static inline instead of extern inline in ftrace code.
- Crypto ARM assembly updates for big endian
- Alignment of initrd/.init memory to page sizes when freeing to
ensure that we fully free the regions
- Add gcov support
- A couple of preparatory patches for VDSO support: use
_install_special_mapping, and randomize the sigpage placement above
stack.
- Add L2 ePAPR DT cache properties so that DT can specify the cache
geometry.
- Preparatory patch for FIQ (NMI) kernel C code for things like
spinlock lockup debug. Following on from this are a couple of my
patches cleaning up show_regs() and removing an unused (probably
since 1.x days) do_unexp_fiq() function.
- Use pr_warn() rather than pr_warning().
- A number of cleanups (smp, footbridge, return_address)"
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (21 commits)
ARM: 8167/1: extend the reserved memory for initrd to be page aligned
ARM: 8168/1: extend __init_end to a page align address
ARM: 8169/1: l2c: parse cache properties from ePAPR definitions
ARM: 8160/1: drop warning about return_address not using unwind tables
ARM: 8161/1: footbridge: select machine dir based on ARCH_FOOTBRIDGE
ARM: 8158/1: LLVMLinux: use static inline in ARM ftrace.h
ARM: 8155/1: place sigpage at a random offset above stack
ARM: 8154/1: use _install_special_mapping for sigpage
ARM: 8153/1: Enable gcov support on the ARM architecture
ARM: Avoid writing to control register on every exception
ARM: 8152/1: Convert pr_warning to pr_warn
ARM: remove unused do_unexp_fiq() function
ARM: remove extraneous newline in show_regs()
ARM: 8150/3: fiq: Replace default FIQ handler
ARM: 8140/1: ep93xx: Enable DEBUG_LL_UART_PL01X
ARM: 8139/1: versatile: Enable DEBUG_LL_UART_PL01X
ARM: 8138/1: drop ISAR0 workaround for B15
ARM: 8136/1: sa1100: add Micro ASIC platform device
ARM: 8131/1: arm/smp: Absorb boot_secondary()
ARM: 8126/1: crypto: enable NEON SHA-384/SHA-512 for big endian
...
Pull KVM updates from Paolo Bonzini:
"Fixes and features for 3.18.
Apart from the usual cleanups, here is the summary of new features:
- s390 moves closer towards host large page support
- PowerPC has improved support for debugging (both inside the guest
and via gdbstub) and support for e6500 processors
- ARM/ARM64 support read-only memory (which is necessary to put
firmware in emulated NOR flash)
- x86 has the usual emulator fixes and nested virtualization
improvements (including improved Windows support on Intel and
Jailhouse hypervisor support on AMD), adaptive PLE which helps
overcommitting of huge guests. Also included are some patches that
make KVM more friendly to memory hot-unplug, and fixes for rare
caching bugs.
Two patches have trivial mm/ parts that were acked by Rik and Andrew.
Note: I will soon switch to a subkey for signing purposes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (157 commits)
kvm: do not handle APIC access page if in-kernel irqchip is not in use
KVM: s390: count vcpu wakeups in stat.halt_wakeup
KVM: s390/facilities: allow TOD-CLOCK steering facility bit
KVM: PPC: BOOK3S: HV: CMA: Reserve cma region only in hypervisor mode
arm/arm64: KVM: Report correct FSC for unsupported fault types
arm/arm64: KVM: Fix VTTBR_BADDR_MASK and pgd alloc
kvm: Fix kvm_get_page_retry_io __gup retval check
arm/arm64: KVM: Fix set_clear_sgi_pend_reg offset
kvm: x86: Unpin and remove kvm_arch->apic_access_page
kvm: vmx: Implement set_apic_access_page_addr
kvm: x86: Add request bit to reload APIC access page address
kvm: Add arch specific mmu notifier for page invalidation
kvm: Rename make_all_cpus_request() to kvm_make_all_cpus_request() and make it non-static
kvm: Fix page ageing bugs
kvm/x86/mmu: Pass gfn and level to rmapp callback.
x86: kvm: use alternatives for VMCALL vs. VMMCALL if kernel text is read-only
kvm: x86: use macros to compute bank MSRs
KVM: x86: Remove debug assertion of non-PAE reserved bits
kvm: don't take vcpu mutex for obviously invalid vcpu ioctls
kvm: Faults which trigger IO release the mmap_sem
...
It is currently possible to execve() an x32 executable on an x86_64
kernel that has only ia32 compat enabled. However all its syscalls
will fail, even _exit(). This usually causes it to segfault.
Change the ELF compat architecture check so that x32 executables are
rejected if we don't support the x32 ABI.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Link: http://lkml.kernel.org/r/1410120305.6822.9.camel@decadent.org.uk
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This adds hooks into the core powerpc mm code for cxl.
The core powerpc code sometimes uses local tlbie. Unfortunately this won't
work with the current cxl driver as it relies on snooping tlbie broadcasts.
The cxl hardware can have TLB entries invalidated via MMIO but this is not
currently supported by the driver. In future we can make local tlbie smarter so
that it invalidates cxl contexts via MMIO when it needs to but for now we have
this workaround.
This workaround checks for any active cxl contexts and if so, disables local
tlbie.
This also adds a hook for when SLBs are invalidated. This ensures any
corresponding SLBs in cxl are also invalidated at the same time. This is
required for segment demotion.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds a new function hash_page_mm() based on the existing hash_page().
This version allows any struct mm to be passed in, rather than assuming
current. This is useful for servicing co-processor faults which are not in the
context of the current running process.
We need to be careful here as the current hash_page() assumes current in a few
places.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds a number of functions for allocating IRQs under powernv PCIe for cxl.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some of the MSI IRQ code in pnv_pci_ioda_msi_setup() is generically useful so
split it out.
This will be used by some of the cxl PCIe code later.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Export mmu_kernel_ssize and mmu_linear_psize. These are needed by the cxl
driver which has it's own MMU. To setup the MMU cxl needs access to these.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently msi_bitmap_alloc_hwirqs() will round up any IRQ allocation requests
to the nearest power of 2. eg. ask for 5 IRQs and you'll get 8. This wastes a
lot of IRQs which can be a scarce resource.
For cxl we may require multiple IRQs for every context that is attached to the
accelerator. There may be 1000s of contexts attached, hence we can easily run
out of IRQs, especially if we are needlessly wasting them.
This changes the msi_bitmap_alloc_hwirqs() to allocate only the required number
of IRQs, hence avoiding this wastage. It keeps the natural alignment
requirement though.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This moves spu_flush_all_slbs() into a generic call copro_flush_all_slbs().
This will be useful when we add cxl which also needs a similar SLB flush call.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
__spu_trap_data_seg() currently contains code to determine the VSID and ESID
required for a particular EA and mm struct.
This code is generically useful for other co-processors. This moves the code of
the cell platform so it can be used by other powerpc code. It also adds 1TB
segment handling which Cell didn't support. The new function is called
copro_calculate_slb().
This also moves the internal struct spu_slb to a generic struct copro_slb which
is now used in the Cell and copro code. We use this new struct instead of
passing around esid and vsid parameters.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently spu_handle_mm_fault() is in the cell platform.
This code is generically useful for other non-cell co-processors on powerpc.
This patch moves this function out of the cell platform into arch/powerpc/mm so
that others may use it.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Intel processors which don't report cache information via cpuid(2)
or cpuid(4) need quirk code in the legacy_cache_size callback to
report this data. For Intel that callback is is intel_size_cache().
This patch enables calling of cpu_detect_cache_sizes() inside of
init_intel() and hence the calling of the legacy_cache callback in
intel_size_cache(). Adding this call will ensure that PIII Tualatin
currently in intel_size_cache() and Quark SoC X1000 being added to
intel_size_cache() in this patch will report their respective cache
sizes.
This model of calling cpu_detect_cache_sizes() is consistent with
AMD/Via/Cirix/Transmeta and Centaur.
Also added is a string to idenitfy the Quark as Quark SoC X1000
giving better and more descriptive output via /proc/cpuinfo
Adding cpu_detect_cache_sizes to init_intel() will enable calling
of intel_size_cache() on Intel processors which currently no code
can reach. Therefore this patch will also re-enable reporting
of PIII Tualatin cache size information as well as add
Quark SoC X1000 support.
Comment text and cache flow logic suggested by Thomas Gleixner
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: davej@redhat.com
Cc: hmh@hmh.eng.br
Link: http://lkml.kernel.org/r/1412641189-12415-3-git-send-email-pure.logic@nexus-software.ie
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Quark SoC X1000 advertises Page Global Enable for it's
Translation Lookaside Buffer via cpuid. The silicon does not
in fact support PGE and hence will not flush the TLB when CR4.PGE
is rewritten. The Quark documentation makes clear the necessity to
instead rewrite CR3 in order to flush any TLB entries, irrespective
of the state of CR4.PGE or an individual PTE.PGE
See Intel Quark Core DevMan_001.pdf section 6.4.11
In setup.c setup_arch() the code will load_cr3() and then do a
__flush_tlb_all().
On Quark the entire TLB will be flushed at the load_cr3().
The __flush_tlb_all() have no effect and can be safely ignored.
Later on in the boot process we switch off the flag for cpu_has_pge()
which means that subsequent calls to __flush_tlb_all() will
call __flush_tlb() not __flush_tlb_global() flushing the TLB in the
correct way via load_cr3() not CR4.PGE rewrite
This patch documents the behaviour of flushing the TLB for Quark in
setup_arch()
Comment text suggested by Thomas Gleixner
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: davej@redhat.com
Cc: hmh@hmh.eng.br
Link: http://lkml.kernel.org/r/1412641189-12415-2-git-send-email-pure.logic@nexus-software.ie
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The patch 30058677 "ARM / highbank: add support for pl320 IPC"
added a pl320 IPC specific header file as a generic mailbox.h.
This file has been renamed appropriately to allow the
introduction of the generic mailbox API framework.
Acked-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Pull pin control changes from Linus Walleij:
"This is the bulk of pin control changes for the v3.18 development
series:
- New drivers for the Freescale i.MX21, Qualcomm APQ8084 pin
controllers.
- Incremental new features on the Rockchip, atlas 6, OMAP, AM437x,
APQ8064, prima2, AT91, Tegra, i.MX, Berlin and Nomadik.
- Push Freescale drivers down into their own subdirectory.
- Assorted sprays of syntax and semantic fixes"
* tag 'pinctrl-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (48 commits)
pinctrl: specify bindings for pins and groups
pinctrl: nomadik: improve GPIO debug prints
pinctrl: abx500: refactor DT parser to take two paths
pinctrl: abx500: use helpers for map allocation/free
pinctrl: alter device tree bindings for functions
pinctrl: nomadik: refactor DT parser to take two paths
pinctrl: nomadik: use utils map free function
pinctrl: nomadik: use util function to reserve maps
pinctrl: qcom: use restart_notifier mechanism for ps_hold
pinctrl: sh-pfc: sh73a0: Remove unnecessary SoC data allocation
pinctrl: berlin: fix the dt_free_map function
pinctrl: at91: disable PD or PU before enabling PU or PD
pinctrl: st: remove gpiochip in failure cases
pinctrl: at91: Fix error handling while doing gpiochio_irqchip_add
pinctrl: at91: Fix failure path in at91_gpio_probe path
pinctrl: lantiq: Release gpiochip resources in fail case
pinctrl: imx: detect uninitialized pins
pinctrl: tegra: Add MIPI pad control
pinctrl: at91: Switch to using managed clk_get
pinctrl: adi2: Remove duplicate gpiochip_remove_pin_ranges
...
Pull "tinification" patches from Josh Triplett.
Work on making smaller kernels.
* tag 'tiny/for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/josh/linux:
bloat-o-meter: Ignore syscall aliases SyS_ and compat_SyS_
mm: Support compiling out madvise and fadvise
x86: Support compiling out human-friendly processor feature names
x86: Drop support for /proc files when !CONFIG_PROC_FS
x86, boot: Don't compile early_serial_console.c when !CONFIG_EARLY_PRINTK
x86, boot: Don't compile aslr.c when !CONFIG_RANDOMIZE_BASE
x86, boot: Use the usual -y -n mechanism for objects in vmlinux
x86: Add "make tinyconfig" to configure the tiniest possible kernel
x86, platform, kconfig: move kvmconfig functionality to a helper
Now that we define these in the KVM code, use these defines when we call
H_SET_MODE. No functional change.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
catalog_read() implements the read interface for the sysfs file
/sys/bus/event_source/devices/hv_24x7/interface/catalog
It essentially takes a buffer, an offset and count as parameters
to the read() call. It makes a hypervisor call to read a specific
page from the catalog and copy the required bytes into the given
buffer. Each call to catalog_read() returns at most one 4K page.
Given these requirements, we should be able to simplify the
catalog_read().
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Ian pointed out the use of __aligned(4096) caused rather large stack
consumption in single_24x7_request(), so use the kmem_cache
hv_page_cache (which we've already got set up for other allocations)
insead of allocating locally.
CC: Haren Myneni <hbabu@us.ibm.com>
Reported-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Cody P Schafer <dev@codyps.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When reading from the LPC, the OPAL FW calls return the value via pointer
to a uint32_t which is always returned big endian. Our internal inb/outb
implementation byteswaps that fine but our debugfs code is still broken.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
* pm-cpufreq:
cpufreq: cpufreq-dt: fix potential double put of cpu OF node
cpufreq: cpu0: rename driver and internals to 'cpufreq_dt'
cpufreq: ppc-corenet: remove duplicate update of cpu_data
cpufreq: Replace strnicmp with strncasecmp
cpufreq: powernv: Set the cpus to nominal frequency during reboot/kexec
cpufreq: powernv: Set the pstate of the last hotplugged out cpu in policy->cpus to minimum
cpufreq: Allow stop CPU callback to be used by all cpufreq drivers
cpufreq: cpu0: Make allocate_resources() work for any CPU
cpufreq: cpu0: try regulators with name "cpu-supply"
cpufreq: cpu0: Move per-cluster initialization code to ->init()
cpufreq: cpu0: use dev_{err|warn|dbg} instead of pr_{err|warn|debug}
cpufreq: cpu0: print relevant error when we defer probe
cpufreq: cpu0: don't validate clock on clk_put()
cpufreq: cpu0: Update Module Author
cpufreq: Add support for per-policy driver data
* pm-cpuidle:
drivers: cpuidle: initialize big.LITTLE driver through DT
drivers: cpuidle: CPU idle ARM64 driver
drivers: cpuidle: implement DT based idle states infrastructure
cpuidle: big.LITTLE: add Exynos5800 compatible string
cpuidle: Replace strnicmp with strncasecmp
arm64: add PSCI CPU_SUSPEND based cpu_suspend support
arm64: kernel: introduce cpu_init_idle CPU operation
arm64: kernel: refactor the CPU suspend API for retention states
Documentation: arm: define DT idle states bindings
* pm-genirq:
PM / genirq: Document rules related to system suspend and interrupts
PCI / PM: Make PCIe PME interrupts wake up from suspend-to-idle
x86 / PM: Set IRQCHIP_SKIP_SET_WAKE for IOAPIC IRQ chip objects
genirq: Simplify wakeup mechanism
genirq: Mark wakeup sources as armed on suspend
genirq: Create helper for flow handler entry check
genirq: Distangle edge handler entry
genirq: Avoid double loop on suspend
genirq: Move MASK_ON_SUSPEND handling into suspend_device_irqs()
genirq: Make use of pm misfeature accounting
genirq: Add sanity checks for PM options on shared interrupt lines
genirq: Move suspend/resume logic into irq/pm code
PM / sleep: Mechanism for aborting system suspends unconditionally
The NT flag doesn't do anything in long mode other than causing IRET
to #GP. Oddly, CPL3 code can still set NT using popf.
Entry via hardware or software interrupt clears NT automatically, so
the only relevant entries are fast syscalls.
If user code causes kernel code to run with NT set, then there's at
least some (small) chance that it could cause trouble. For example,
user code could cause a call to EFI code with NT set, and who knows
what would happen? Apparently some games on Wine sometimes do
this (!), and, if an IRET return happens, they will segfault. That
segfault cannot be handled, because signal delivery fails, too.
This patch programs the CPU to clear NT on entry via SYSCALL (both
32-bit and 64-bit, by my reading of the AMD APM), and it clears NT
in software on entry via SYSENTER.
To save a few cycles, this borrows a trick from Jan Beulich in Xen:
it checks whether NT is set before trying to clear it. As a result,
it seems to have very little effect on SYSENTER performance on my
machine.
There's another minor bug fix in here: it looks like the CFI
annotations were wrong if CONFIG_AUDITSYSCALL=n.
Testers beware: on Xen, SYSENTER with NT set turns into a GPF.
I haven't touched anything on 32-bit kernels.
The syscall mask change comes from a variant of this patch by Anish
Bhatt.
Note to stable maintainers: there is no known security issue here.
A misguided program can set NT and cause the kernel to try and fail
to deliver SIGSEGV, crashing the program. This patch fixes Far Cry
on Wine: https://bugs.winehq.org/show_bug.cgi?id=33275
Cc: <stable@vger.kernel.org>
Reported-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/395749a5d39a29bd3e4b35899cf3a3c1340e5595.1412189265.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This fixes two bugs in PVH guests:
- Not setting EFER.NX means the NX bit in page table entries is
ignored on Intel processors and causes reserved bit page faults on
AMD processors.
- After the Xen commit 7645640d6ff1 ("x86/PVH: don't set EFER_SCE for
pvh guest") PVH guests are required to set EFER.SCE to enable the
SYSCALL instruction.
Secondary VCPUs are started with pagetables with the NX bit set so
EFER.NX must be set before using any stack or data segment.
xen_pvh_cpu_early_init() is the new secondary VCPU entry point that
sets EFER before jumping to cpu_bringup_and_idle().
Signed-off-by: Mukesh Rathor <mukesh.rathor@oracle.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
swapper_low_pmd_dir and swapper_pud_dir are actually completely
useless and unnecessary.
We just need swapper_pg_dir[]. Naturally the other page table chunks
will be allocated on an as-needed basis. Since the kernel actually
accesses these tables in the PAGE_OFFSET view, there is not even a TLB
locality advantage of placing them in the kernel image.
Use the hard coded vmlinux.ld.S slot for swapper_pg_dir which is
naturally page aligned.
Increase MAX_BANKS to 1024 in order to handle heavily fragmented
virtual guests.
Even with this MAX_BANKS increase, the kernel is 20K+ smaller.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Bob Picco <bob.picco@oracle.com>
This patch attempts to do a few things. The highlights are: 1) enable
SPARSE_IRQ unconditionally, 2) kills off !SPARSE_IRQ code 3) allocates
ivector_table at boot time and 4) default to cookie only VIRQ mechanism
for supported firmware. The first firmware with cookie only support for
me appears on T5. You can optionally force the HV firmware to not cookie
only mode which is the sysino support.
The sysino is a deprecated HV mechanism according to the most recent
SPARC Virtual Machine Specification. HV_GRP_INTR is what controls the
cookie/sysino firmware versioning.
The history of this interface is:
1) Major version 1.0 only supported sysino based interrupt interfaces.
2) Major version 2.0 added cookie based VIRQs, however due to the fact
that OSs were using the VIRQs without negoatiating major version
2.0 (Linux and Solaris are both guilty), the VIRQs calls were
allowed even with major version 1.0
To complicate things even further, the VIRQ interfaces were only
actually hooked up in the hypervisor for LDC interrupt sources.
VIRQ calls on other device types would result in HV_EINVAL errors.
So effectively, major version 2.0 is unusable.
3) Major version 3.0 was created to signal use of VIRQs and the fact
that the hypervisor has these calls hooked up for all interrupt
sources, not just those for LDC devices.
A new boot option is provided should cookie only HV support have issues.
hvirq - this is the version for HV_GRP_INTR. This is related to HV API
versioning. The code attempts major=3 first by default. The option can
be used to override this default.
I've tested with SPARSE_IRQ on T5-8, M7-4 and T4-X and Jalap?no.
Signed-off-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to accomodate embedded per-cpu allocation with large numbers
of cpus and numa nodes, we have to use as much virtual address space
as possible for the vmalloc region. Otherwise we can get things like:
PERCPU: max_distance=0x380001c10000 too large for vmalloc space 0xff00000000
So, once we select a value for PAGE_OFFSET, derive the size of the
vmalloc region based upon that.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Bob Picco <bob.picco@oracle.com>
