Adding CPSW phy-id, CPSW and MDIO pinmux configuration for active and
sleep states and enable them in board evm dts file.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DRA7 Data Manual (SPRS857L - August 2014) section 4.1.1 states: "All
unused power supply balls must be supplied with the voltages specified
in the Section 5.2, Recommended Operating Conditions".
This implies that all unused voltage rails for Vayu can never be
switched off even if the hardware blocks inside that voltage domain is
unused. Switching off these unused rails may result in stability issues
on other domains and increased leakage and power-on-hour impacts.
J6eco-evm dts file already considers this, however j6evm-dts file needs
to be fixed to consider this constraint of the SoC.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add MMC1 and 2 nodes. MMC1 is SDcard and MMC2 is eMMC.
NOTE on MMC1 card detect: Ideally, we should be using in-built SDCD
support, but we dont have it yet. So, use the fact that control module
of DRA7 is setup such that no matter what mode one configures it, GPIO
option is always hardwired in - use GPIO mode for SDcard detection.
[peter.ujfalusi@ti.com]
The power line feeding the SD card is also used by other devices on the EVM.
Use generic name instead of mmc2_3v3 so when other devices want to use the
same regulator it will look a bit better.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With Commit adff5962fd ("Input: introduce palmas-pwrbutton"), we can
now support tps power button as a event source - This is SW7 (PB/WAKE)
on the J6-evm.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Even thought sys_nirq1 is hardwired on the SoC for the pin, it is
better to configure the pin to the required mux configuration.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The ldo4_reg regulator provides power to the USB1 and USB2
High Speed PHYs.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The 4th USB controller instance present only on the DRA74x family of
devices so move it there.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DRA72-evm has a 256MB 16-bit wide NAND chip. Add
pinmux and NAND node.
The NAND chips 'Chip select' and 'Write protect' can be
controlled using DIP Switch SW5. To use NAND,
the switch must be configured like so:
SW5.1 (NAND_SELn) = ON (LOW)
SW5.9 (GPMC_WPN) = OFF (HIGH)
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adding CPSW phy-id, CPSW and MDIO pinmux configuration for active and
sleep states and enable them in board evm dts file.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add CPSW and MDIO related device tree data for DRA7XX and made as status
disabled. Phy-id, pinmux for active and sleep state needs to be added in
board dts files and enable the CPSW device.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use omap specific pinctrl defines (OMAP3_CORE1_IOPAD) to configure
the padconf register offset.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add DSS related pinmux and display data nodes required to support
DVI video out on SBC-T3530, SBC-T3730 and SBC-T3517.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Switch over the msgctl, shmat, shmctl and semtimedop syscalls to use the compat
layer. The problem was found with the debian procenv package, which called
shmctl(0, SHM_INFO, &info);
in which the shmctl syscall then overwrote parts of the surrounding areas on
the stack on which the info variable was stored and thus lead to a segfault
later on.
Additionally fix the definition of struct shminfo64 to use unsigned longs like
the other architectures. This has no impact on userspace since we only have a
32bit userspace up to now.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: John David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org> # v3.10+
DCDC3 supplies voltage to DDR. Fix DCDC3 volatge to 1.5V which is the reset
value. Programming to a non-reset value while executing from DDR will result
in random hangs.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DCDC3 supplies voltage to DDR. Fix DCDC3 volatge to 1.5V which is the reset
value. Programming to a non-reset value while executing from DDR will result
in random hangs.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DCDC3 supplies voltage to DDR. Fix DCDC3 volatge to 1.5V which is the reset
value. Programming to a non-reset value while executing from DDR will result
in random hangs.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the interrupts property to all the 13 mailbox nodes in
DRA7xx. The interrupts property information added is inline
with the expected values with the DRA7xx crossbar driver,
and is common to both DRA74x and DRA72x SoCs.
Do note that the mailbox 1 is only capable of generating out
3 interrupts, while all the remaining mailboxes have 4
interrupts each.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These fields were added by:
commit 9574f36fb8
OMAP/serial: Add support for driving a GPIO as DTR.
but not removed by
commit 985bfd54c8
tty: serial: omap: remove some dead code
which reverted most of that commit.
Time to revert the rest.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP3 and lower SoCs don't have the ELM module so this warning
is annoying. Get rid of it.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull two fixes for early microcode loader on 32-bit from Borislav Petkov:
- access the dis_ucode_ldr chicken bit properly
- fix patch stashing on AMD on 32-bit
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Include the generic I/O header file so that duplicate implementations
can be removed. This will also help to establish consistency across more
architectures regarding which accessors they support.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Include the generic I/O header file so that duplicate implementations
can be removed. This will also help to establish consistency across more
architectures regarding which accessors they support.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The xlate_dev_{kmem,mem}_ptr() functions take either a physical address
or a kernel virtual address, so data types should be phys_addr_t and
void *. They both return a kernel virtual address which is only ever
used in calls to copy_{from,to}_user(), so make variables that store it
void * rather than char * for consistency.
Also only define a weak unxlate_dev_mem_ptr() function if architectures
haven't overridden them in the asm/io.h header file.
Signed-off-by: Thierry Reding <treding@nvidia.com>
xlate_dev_mem_ptr() is used to convert a physical address to an uncached
kernel virtual address mapping, so make it use phys_addr_t as type for
the physical address and return void * for the kernel virtual address.
xlate_dev_kmem_ptr() converts a cached kernel virtual address mapping to
an uncached kernel virtual address mapping, so make it use void * for
both the input parameter and return value.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to override accessors properly they must be #define'd so that
subsequent generic headers (the one for ARM and finally the architecture
independent one) can properly detect it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Provide *_relaxed() accessors and make sure to pass the volatile void
__iomem * to accessors rather than the value cast to a u32. This allows
ixp4xx to build with IXP4XX_INDIRECT_PCI enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to override accessors properly they must be #define'd so that
subsequent generic headers (the one for ARM and finally the architecture
independent one) can properly detect it.
While at it, make all accessors use volatile void __iomem * to avoid a
slew of build warnings.
Signed-off-by: Thierry Reding <treding@nvidia.com>
PCIDs are only supported in 64-bit mode. No need to clear bit 63
of CR3 unless the host is 64-bit.
Reported by Fengguang Wu's autobuilder.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Save the patch while we're running on the BSP instead of later, before
the initrd has been jettisoned. More importantly, on 32-bit we need to
access the physical address instead of the virtual.
This way we actually do find it on the APs instead of having to go
through the initrd each time.
Tested-by: Richard Hendershot <rshendershot@mchsi.com>
Fixes: 5335ba5cf4 ("x86, microcode, AMD: Fix early ucode loading")
Cc: <stable@vger.kernel.org> # v3.13+
Signed-off-by: Borislav Petkov <bp@suse.de>
ARC's asm/io.h includes the asm-generic/io.h which already defines the
PCI_IOBASE variable in exactly the same way, so it can be dropped from
the architecture specific header.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Fixes the following missing includes:
arch/arm/mach-at91/at91sam9g45.c: In function 'at91sam9g45_init_time':
arch/arm/mach-at91/at91sam9g45.c:39:23: error: 'NR_IRQS_LEGACY' undeclared (first use in this function)
at91sam926x_pit_init(NR_IRQS_LEGACY + AT91_ID_SYS);
^
arch/arm/mach-at91/at91sam9g45.c:39:23: note: each undeclared identifier is reported only once for each function it appears in
make[3]: *** [arch/arm/mach-at91/at91sam9g45.o] Error 1
arch/arm/mach-at91/at91sam9rl.c: In function 'at91sam9rl_init_time':
arch/arm/mach-at91/at91sam9rl.c:51:23: error: 'NR_IRQS_LEGACY' undeclared (first use in this function)
at91sam926x_pit_init(NR_IRQS_LEGACY + AT91_ID_SYS);
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
alloc_bootmem and related functions always return a zeroed region of memory.
Thus a memset after calls to these functions is unnecessary.
The following Coccinelle semantic patch was used for making the change:
@@
expression E,E1;
@@
E = \(alloc_bootmem\|alloc_bootmem_low\|alloc_bootmem_pages\|alloc_bootmem_low_pages\)(...)
... when != E
- memset(E,0,E1);
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Port the sh73a0 restart handling from the kzm9g-legacy board code to the
kzm9g-reference board code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
