This patch introduces the support for Keymile's kmcoge4 board which is
the internal reference design for boards based on Freescale's
P2040/P2041 SoCs. This internal reference design is named kmp204x.
The peripherals used on this board are:
- SPI NOR Flash as bootloader medium
- NAND Flash with a ubi partition
- 2 PCIe busses (hosts 1 and 3)
- 3 FMAN Ethernet devices (FMAN1 DTSEC1/2/5)
- 4 Local Bus windows, with one dedicated to the QRIO reset/power mgmt
CPLD
- 2 I2C busses
- last but not least, the mandatory serial port
The patch also adds a defconfig file for this reference design that is
necessary because of the lowmem option that must be set higher due to
the number of PCIe devices with big ioremapped mem ranges on the boad.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
PCI controller disable PME message report feature, that shouldn't
have happened. Fix it and enable PME message report feature.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
There are error parameters should be corrected when
calling dma_free_coherent to free rmu rx-ring buffers
in fsl_open_inb_mbox() function.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The only way Freescale booke chips support mappings larger than 4K
is via TLB1. The only way we support (direct) TLB1 entries is via
hugetlb, which is not what map_kernel_page() does when given a large
page size.
Without this, a kernel with CONFIG_SPARSEMEM_VMEMMAP enabled crashes on
boot with messages such as:
PID hash table entries: 4096 (order: 3, 32768 bytes)
Sorting __ex_table...
BUG: Bad page state in process swapper pfn:00a2f
page:8000040000023a48 count:0 mapcount:0 mapping:0000040000ffce48 index:0x40000ffbe50
page flags: 0x40000ffda40(active|arch_1|private|private_2|head|tail|swapcache|mappedtodisk|reclaim|swapbacked|unevictable|mlocked)
page dumped because: PAGE_FLAGS_CHECK_AT_FREE flag(s) set
bad because of flags:
page flags: 0x311840(active|private|private_2|swapcache|unevictable|mlocked)
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 3.15.0-rc1-00003-g7fa250c #299
Call Trace:
[c00000000098ba20] [c000000000008b3c] .show_stack+0x7c/0x1cc (unreliable)
[c00000000098baf0] [c00000000060aa50] .dump_stack+0x88/0xb4
[c00000000098bb70] [c0000000000c0468] .bad_page+0x144/0x1a0
[c00000000098bc10] [c0000000000c0628] .free_pages_prepare+0x164/0x17c
[c00000000098bcc0] [c0000000000c24cc] .free_hot_cold_page+0x48/0x214
[c00000000098bd60] [c00000000086c318] .free_all_bootmem+0x1fc/0x354
[c00000000098be70] [c00000000085da84] .mem_init+0xac/0xdc
[c00000000098bef0] [c0000000008547b0] .start_kernel+0x21c/0x4d4
[c00000000098bf90] [c000000000000448] .start_here_common+0x20/0x58
Signed-off-by: Scott Wood <scottwood@freescale.com>
Two issues:
o For beql_op, beql_op, bne_op, bnel_op, blez_op, blezl_op, bgtz_op and
bgtzl_op the wrong field was being checked for the instruction opcode.
o For blez_op / blezl_op and bgtz_op / bgtzl_op the test was testing
for the wrong opcode.
This bug got introduced by d8d4e3ae0b [MIPS
Kprobes: Refactor branch emulation].
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Acked-by: Victor Kamensky <kamensky@cisco.com>
Add support for the 2 SDHC controllers on the DB8074 board. The first
controller (at 0xf9824900) is connected to an on board soldered eMMC.
The second controller (at 0xf98a4900) is connected to a uSD card slot.
Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
The SoCFPGA has two watchdog timers. Add them to the dtsi.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
[dinh: modified patch to have correct irq flag]
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
The cycloneV has three gpio controllers, each one with 29 gpios. This patch
adds the three controller with the gpio driver which is now sitting the
gpio tree.
Cc: devicetree@vger.kernel.org
Acked-by: Alan Tull <atull@altera.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Parsing and registration of fixed PHY devices was needed with the use of
of_phy_connect_fixed_link() because this function was using the
designated PHY address identifier (first cell of the property) as the
address to bind the PHY on the emulated bus.
Since commit 3be2a49e5c ("of: provide a
binding for fixed link PHYs") a new pair of functions has been
introduced which allows for dynamic address allocation of these fixed
PHY devices, but also parses the old 'fixed-link' 5-digit property.
Registration of fixed PHY early in platform code was needed because we
could not issue a fixed MDIO bus re-scan within network drivers. The
fixed PHYs had to be registered before the network drivers would call
of_phy_connect_fixed_link(). All of these caveats are solved now, such
that we can safely remove of_add_fixed_phys() now.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables a exynos_usbphy node for exynos4 SoCs.
A exynos4x12 usb phy node is almost same with 4210's one
except compatible string and pmu syscon.
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
sss module device node missed clock macro.
This patch replace magic number with macro in clock
binding for exynos5420.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Reviewed-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Phy and sss module device node missed clock macro.
This patch replace magic number with macros in clock
binding for exynos5250.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Reviewed-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch enables support for multimedia blocks - fimc in
mem2mem mode, no camera sensors support yet.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds device tree nodes necessary to enable USB support on
universalc210 board, this includes UDC controller (USB gadget) as well
as EHCI and OHCI host ports. LDO3 and LDO8 regulators are switched to
always on mode until EHCI and OHCI drivers will support them correctly.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds device tree nodes necessary to enable USB
gadget functionality on Exynos4210-based Trats board.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds the audio subsystem clock controller and the I2S
IP block nodes for Exynos4 SoC series.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixed gpio key device node.
First, fix incorrect gpio property.
And then, add ok-key node where locate bottom center.
I have tested on exynos4412-trats2 board.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Exynos4412-trats2 board have light/proximity sensor.
This patch add cm36651 light/ proximity sensor node for exynos4412.
cm36651 is required properties as below.
- Use i2c-gpio for cm36651 sensor.
- Use fixed regulator for the IR LED.
It is a part of the cm36651 for proximity detection.
- cm36651 is i2c device driver so need to use i2c-gpio driver.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Separate Qualcomm low-level debugging UART to two options.
DEBUG_MSM_UART is used in earlier non-multi platform arches,
like MSM7X00A, QSD8X50 and MSM7X30.
DEBUG_QCOM_UARTDM is used in multi-plafrom arches and have
embedded data mover.
Make DEBUG_UART_PHYS and DEBUG_UART_BASE user adjustable by
Kconfig menu.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
As some of the IPs on Qualcomm SOCs are based on ARM PrimeCell IPs.
For example SDCC controller is PrimeCell MCI pl180. Adding this option will
give flexibility to reuse the existing drivers as it is without major
modifications.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Use the hexadecimal values for the triggers to match what is done for the device
tree. This also fixes compilation issues as the defines have been moved
elsewhere.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Now that DT based platforms are split out of mach-msm into
mach-qcom, put back a non-DT based SoC into the msm_defconfig and
stop selecting unsupported drivers.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
This patch removes the selection of AT91_USE_OLD_CLK when selecting
sam9n12 SoC support. This will automatically enable COMMON_CLK_AT91 option
and add support for at91 common clk implementation.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Tested-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch removes the selection of AT91_USE_OLD_CLK when selecting
sam9x5 SoCs support. This will automatically enable COMMON_CLK_AT91 option
and add support for at91 common clk implementation.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The DR7 masking which is done on task switch emulation should be in hex format
(clearing the local breakpoints enable bits 0,2,4 and 6).
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
CS.RPL is not equal to the CPL in the few instructions between
setting CR0.PE and reloading CS. And CS.DPL is also not equal
to the CPL for conforming code segments.
However, SS.DPL *is* always equal to the CPL except for the weird
case of SYSRET on AMD processors, which sets SS.DPL=SS.RPL from the
value in the STAR MSR, but force CPL=3 (Intel instead forces
SS.DPL=SS.RPL=CPL=3).
So this patch:
- modifies SVM to update the CPL from SS.DPL rather than CS.RPL;
the above case with SYSRET is not broken further, and the way
to fix it would be to pass the CPL to userspace and back
- modifies VMX to always return the CPL from SS.DPL (except
forcing it to 0 if we are emulating real mode via vm86 mode;
in vm86 mode all DPLs have to be 3, but real mode does allow
privileged instructions). It also removes the CPL cache,
which becomes a duplicate of the SS access rights cache.
This fixes doing KVM_IOCTL_SET_SREGS exactly after setting
CR0.PE=1 but before CS has been reloaded.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
I noticed on some of my systems that page fault tracing doesn't
work:
cd /sys/kernel/debug/tracing
echo 1 > events/exceptions/enable
cat trace;
# nothing shows up
I eventually traced it down to CONFIG_KVM_GUEST. At least in a
KVM VM, enabling that option breaks page fault tracing, and
disabling fixes it. I tried on some old kernels and this does
not appear to be a regression: it never worked.
There are two page-fault entry functions today. One when tracing
is on and another when it is off. The KVM code calls do_page_fault()
directly instead of calling the traced version:
> dotraplinkage void __kprobes
> do_async_page_fault(struct pt_regs *regs, unsigned long
> error_code)
> {
> enum ctx_state prev_state;
>
> switch (kvm_read_and_reset_pf_reason()) {
> default:
> do_page_fault(regs, error_code);
> break;
> case KVM_PV_REASON_PAGE_NOT_PRESENT:
I'm also having problems with the page fault tracing on bare
metal (same symptom of no trace output). I'm unsure if it's
related.
Steven had an alternative to this which has zero overhead when
tracing is off where this includes the standard noops even when
tracing is disabled. I'm unconvinced that the extra complexity
of his apporach:
http://lkml.kernel.org/r/20140508194508.561ed220@gandalf.local.home
is worth it, expecially considering that the KVM code is already
making page fault entry slower here. This solution is
dirt-simple.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86@kernel.org
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Gleb Natapov <gleb@redhat.com>
Cc: kvm@vger.kernel.org
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Table 7-1 of the SDM mentions a check that the code segment's
DPL must match the selector's RPL. This was not done by KVM,
fix it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
During task switch, all of CS.DPL, CS.RPL, SS.DPL must match (in addition
to all the other requirements) and will be the new CPL. So far this
worked by carefully setting the CS selector and flag before doing the
task switch; setting CS.selector will already change the CPL.
However, this will not work once we get the CPL from SS.DPL, because
then you will have to set the full segment descriptor cache to change
the CPL. ctxt->ops->cpl(ctxt) will then return the old CPL during the
task switch, and the check that SS.DPL == CPL will fail.
Temporarily assume that the CPL comes from CS.RPL during task switch
to a protected-mode task. This is the same approach used in QEMU's
emulation code, which (until version 2.0) manually tracks the CPL.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add some documentation to cover the outer cache functions so that their
requirements can be better understood. Of particular note are the
flush_all() and disable() methods which must not be called except in
very specific circumstances.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Santosh says:
> But we should kill all of that since we long back decided to remove
> ES1.0 related code. The mach-omap code alreasy has removed the ES1.0
> compatibility so feel free to remove any specific ES1.0
> related stuff. That silicon is long dead.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
