Fix code that handles KVM_SET_ONE_REG, KVM_GET_ONE_REG ioctls to work in BE
image. Before this fix get/set_one_reg functions worked correctly only in
LE case - reg_from_user was taking 'void *' kernel address that actually could
be target/source memory of either 4 bytes size or 8 bytes size, and code copied
from/to user memory that could hold either 4 bytes register, 8 byte register
or pair of 4 bytes registers.
In order to work in endian agnostic way reg_from_user to reg_to_user functions
should copy register value only to kernel variable with size that matches
register size. In few place where size mismatch existed fix issue on macro
caller side.
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In some cases the mcrr and mrrc instructions in combination with the ldrd
and strd instructions need to deal with 64bit value in memory. The ldrd
and strd instructions already handle endianness within word (register)
boundaries but to get effect of the whole 64bit value represented correctly,
rr_lo_hi macro is introduced and is used to swap registers positions when
the mcrr and mrrc instructions are used. That has the effect of swapping
two words.
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The vgic h/w registers are little endian; when BE asm code
reads/writes from/to them, it needs to do byteswap after/before.
Byteswap code uses ARM_BE8 wrapper to add swap only if
CONFIG_CPU_BIG_ENDIAN is configured.
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Introduce the support code for emulating a GICv2 on top of GICv3
hardware.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
GICv3 requires the IMO and FMO bits to be tightly coupled with some
of the interrupt controller's register switch.
In order to have similar code paths, move the manipulation of these
bits to the GICv2 switch code.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Move the GICv2 world switch code into its own file, and add the
necessary indirection to the arm64 switch code.
Also introduce a new type field to the vgic_params structure.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We already have __hyp_text_{start,end} to express the boundaries
of the HYP text section, and __kvm_hyp_code_{start,end} are getting
in the way of a more modular world switch code.
Just turn __kvm_hyp_code_{start,end} into #defines mapping the
linker-emited symbols.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Brutally hack the innocent vgic code, and move the GICv2 specific code
to its own file, using vgic_ops and vgic_params as a way to pass
information between the two blocks.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
For correct guest suspend/resume behaviour we need to ensure we include
the generic timer registers for 64 bit guests. As CONFIG_KVM_ARM_TIMER is
always set for arm64 we don't need to worry about null implementations.
However I have re-jigged the kvm_arm_timer_set/get_reg declarations to
be in the common include/kvm/arm_arch_timer.h headers.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
I suspect this is a -ECUTPASTE fault from the initial implementation. If
we don't declare the register ID to be KVM_REG_ARM64 the KVM_GET_ONE_REG
implementation kvm_arm_get_reg() returns -EINVAL and hilarity ensues.
The kvm/api.txt document describes all arm64 registers as starting with
0x60xx... (i.e KVM_REG_ARM64).
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
A userspace process can map device MMIO memory via VFIO or /dev/mem,
e.g., for platform device passthrough support in QEMU.
During early development, we found the PAGE_S2 memory type being used
for MMIO mappings. This patch corrects that by using the more strongly
ordered memory type for device MMIO mappings: PAGE_S2_DEVICE.
Signed-off-by: Kim Phillips <kim.phillips@linaro.org>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Currently when a KVM region is deleted or moved after
KVM_SET_USER_MEMORY_REGION ioctl, the corresponding
intermediate physical memory is not unmapped.
This patch corrects this and unmaps the region's IPA range
in kvm_arch_commit_memory_region using unmap_stage2_range.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
unmap_range() was utterly broken, to quote Marc, and broke in all sorts
of situations. It was also quite complicated to follow and didn't
follow the usual scheme of having a separate iterating function for each
level of page tables.
Address this by refactoring the code and introduce a pgd_clear()
function.
Reviewed-by: Jungseok Lee <jays.lee@samsung.com>
Reviewed-by: Mario Smarduch <m.smarduch@samsung.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
This clock type declaration is no longer used as all omap4+ SoC clock
data has been moved to DT, thus remove it.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On Lager board, i2c and iic cores can be interchanged since they can be
muxed to the same wires. Commit e489c2a9bc
("ARM: shmobile: lager: enable i2c devices") activated the i2c cores,
yet the iic cores should be default since they have the more interesting
features for generic use cases, i.e. SMBUS_QUICK and DMA (yet to be
supported).
Reported-by: Khiem Nguyen <khiem.nguyen.xt@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Certain instructions (e.g., mwait and monitor) cause a #UD exception when they
are executed in user mode. This is in contrast to the regular privileged
instructions which cause #GP. In order not to mess with SVM interception of
mwait and monitor which assumes privilege level assertions take place before
interception, a flag has been added.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Certain instructions, such as monitor and xsave do not support big real mode
and cause a #GP exception if any of the accessed bytes effective address are
not within [0, 0xffff]. This patch introduces a flag to mark these
instructions, including the necassary checks.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Emulator accesses are always done a page at a time, either by the emulator
itself (for fetches) or because we need to query the MMU for address
translations. Speed up these accesses by using kvm_read_guest_page
and, in the case of fetches, by inlining kvm_read_guest_virt_helper and
dropping the loop around kvm_read_guest_page.
This final tweak saves 30-100 more clock cycles (4-10%), bringing the
count (as measured by kvm-unit-tests) down to 720-1100 clock cycles on
a Sandy Bridge Xeon host, compared to 2300-3200 before the whole series
and 925-1700 after the first two low-hanging fruit changes.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When the CS base is not page-aligned, the linear address of the code could
get close to the page boundary (e.g. 0x...ffe) even if the EIP value is
not. So we need to first linearize the address, and only then compute
the number of valid bytes that can be fetched.
This happens relatively often when executing real mode code.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We do not need a memory copying loop anymore in insn_fetch; we
can use a byte-aligned pointer to access instruction fields directly
from the fetch_cache. This eliminates 50-150 cycles (corresponding to
a 5-10% improvement in performance) from each instruction.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
do_insn_fetch_bytes will only be called once in a given insn_fetch and
insn_fetch_arr, because in fact it will only be called at most twice
for any instruction and the first call is explicit in x86_decode_insn.
This observation lets us hoist the call out of the memory copying loop.
It does not buy performance, because most fetches are one byte long
anyway, but it prepares for the next patch.
The overflow check is tricky, but correct. Because do_insn_fetch_bytes
has already been called once, we know that fc->end is at least 15. So
it is okay to subtract the number of bytes we want to read.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Hoist the common case up from do_insn_fetch_byte to do_insn_fetch,
and prime the fetch_cache in x86_decode_insn. This helps a bit the
compiler and the branch predictor, but above all it lays the
ground for further changes in the next few patches.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
rip_relative is only set if decode_modrm runs, and if you have ModRM
you will also have a memopp. We can then access memopp unconditionally.
Note that rip_relative cannot be hoisted up to decode_modrm, or you
break "mov $0, xyz(%rip)".
Also, move typecast on "out of range value" of mem.ea to decode_modrm.
Together, all these optimizations save about 50 cycles on each emulated
instructions (4-6%).
Signed-off-by: Bandan Das <bsd@redhat.com>
[Fix immediate operands with rip-relative addressing. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
x86_decode_insn already sets a default for seg_override,
so remove it from the zeroed area. Also replace set/get functions
with direct access to the field.
Signed-off-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A lot of initializations are unnecessary as they get set to
appropriate values before actually being used. Optimize
placement of fields in x86_emulate_ctxt
Signed-off-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove the if conditional - that will help us avoid
an "else initialize to 0" Also, rearrange operators
for slightly better code.
Signed-off-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The same information can be gleaned from ctxt->d and avoids having
to zero/NULL initialize intercept and check_perm
Signed-off-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Core emulator functions all belong in emulator.c,
x86 should have no knowledge of emulator internals
Signed-off-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The "if/return" checks are useless, because we return X86EMUL_CONTINUE
anyway if we do not return.
Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We can just blindly move all 16 bytes of ctxt->src's value to ctxt->dst.
write_register_operand will take care of writing only the lower bytes.
Avoiding a call to memcpy (the compiler optimizes it out) gains about
200 cycles on kvm-unit-tests for register-to-register moves, and makes
them about as fast as arithmetic instructions.
We could perhaps get a larger speedup by moving all instructions _except_
moves out of x86_emulate_insn, removing opcode_len, and replacing the
switch statement with an inlined em_mov.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There are several checks for "peculiar" aspects of instructions in both
x86_decode_insn and x86_emulate_insn. Group them together, and guard
them with a single "if" that lets the processor quickly skip them all.
Make this more effective by adding two more flag bits that say whether the
.intercept and .check_perm fields are valid. We will reuse these
flags later to avoid initializing fields of the emulate_ctxt struct.
This skims about 30 cycles for each emulated instructions, which is
approximately a 3% improvement.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Despite the provisions to emulate up to 130 consecutive instructions, in
practice KVM will emulate just one before exiting handle_invalid_guest_state,
because x86_emulate_instruction always sets KVM_REQ_EVENT.
However, we only need to do this if an interrupt could be injected,
which happens a) if an interrupt shadow bit (STI or MOV SS) has gone
away; b) if the interrupt flag has just been set (other instructions
than STI can set it without enabling an interrupt shadow).
This cuts another 700-900 cycles from the cost of emulating an
instruction (measured on a Sandy Bridge Xeon: 1650-2600 cycles
before the patch on kvm-unit-tests, 925-1700 afterwards).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For the next patch we will need to know the full state of the
interrupt shadow; we will then set KVM_REQ_EVENT when one bit
is cleared.
However, right now get_interrupt_shadow only returns the one
corresponding to the emulated instruction, or an unconditional
0 if the emulated instruction does not have an interrupt shadow.
This is confusing and does not allow us to check for cleared
bits as mentioned above.
Clean the callback up, and modify toggle_interruptibility to
match the comment above the call. As a small result, the
call to set_interrupt_shadow will be skipped in the common
case where int_shadow == 0 && mask == 0.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
About 25% of the time spent in emulation of invalid guest state
is wasted in checking whether emulation is required for the next
instruction. However, this almost never changes except when a
segment register (or TR or LDTR) changes, or when there is a mode
transition (i.e. CR0 changes).
In fact, vmx_set_segment and vmx_set_cr0 already modify
vmx->emulation_required (except that the former for some reason
uses |= instead of just an assignment). So there is no need to
call guest_state_valid in the emulation loop.
Emulation performance test results indicate 1650-2600 cycles
for common instructions, versus 2300-3200 before this patch on
a Sandy Bridge Xeon.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since commit 575203 the MCE subsystem in the Linux kernel for AMD sets bit 18
in MSR_K7_HWCR. Running such a kernel as a guest in KVM on an AMD host results
in a GPE injected into the guest because kvm_set_msr_common returns 1. This
patch fixes this by masking bit 18 from the MSR value desired by the guest.
Signed-off-by: Matthias Lange <matthias.lange@kernkonzept.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We encountered a scenario in which after an INIT is delivered, a pending
interrupt is delivered, although it was sent before the INIT. As the SDM
states in section 10.4.7.1, the ISR and the IRR should be cleared after INIT as
KVM does. This also means that pending interrupts should be cleared. This
patch clears upon reset (and INIT) the pending interrupts; and at the same
occassion clears the pending exceptions, since they may cause a similar issue.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We have noticed that qemu-kvm hangs early in the BIOS when runnning nested
under some versions of VMware ESXi.
The problem we believe is because KVM assumes that the platform preserves
the 'G' but for any segment register. The SVM specification itemizes the
segment attribute bits that are observed by the CPU, but the (G)ranularity bit
is not one of the bits itemized, for any segment. Though current AMD CPUs keep
track of the (G)ranularity bit for all segment registers other than CS, the
specification does not require it. VMware's virtual CPU may not track the
(G)ranularity bit for any segment register.
Since kvm already synthesizes the (G)ranularity bit for the CS segment. It
should do so for all segments. The patch below does that, and helps get rid of
the hangs. Patch applies on top of Linus' tree.
Signed-off-by: Jim Mattson <jmattson@vmware.com>
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Knowing how long we spend in firmware calls is an important part of
minimising OS jitter.
This patch adds tracepoints to each OPAL call. If tracepoints are
enabled we branch out to a common routine that calls an entry and exit
tracepoint.
This allows us to write tools that monitor the frequency and duration
of OPAL calls, eg:
name count total(ms) min(ms) max(ms) avg(ms) period(ms)
OPAL_HANDLE_INTERRUPT 5 0.199 0.037 0.042 0.040 12547.545
OPAL_POLL_EVENTS 204 2.590 0.012 0.036 0.013 2264.899
OPAL_PCI_MSI_EOI 2830 3.066 0.001 0.005 0.001 81.166
We use jump labels if configured, which means we only add a single
nop instruction to every OPAL call when the tracepoints are disabled.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now that we execute the hcall tracepoint entry and exit code out of
line, we can use the same stack across both functions.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
