When the system is halted it makes little sense to reset it. Instead,
hang by executing an infinite loop.
[ralf@linux-mips.org: Remove printk from mips_machine_halt() - this is not
the place to communicate with the user.]
Suggested-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6906/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch introduces code which will enter a suspend state via the
PIIX4. This can only be done when PCI support is enabled since it
requires access to PCI I/O space and the generation of a special cycle
on the PCI bus. In cases where PCI is disabled the mips_pm_suspend
function will simply always return an error.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6905/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On R4k DECstations the Halt button is wired to the NMI processor input
rather than an ordinary interrupt input such as on R3k DECstations. This
is possible with a different design of the CPU daughtercard that routes
the Halt button line from the baseboard connector. Additionally the
interrupt input has been reused for a different purpose on the KN04 and
KN05 R4k CPU daughtercards so it is better kept masked.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6705/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Update to commit 9c9b415c50 [MIPS:
Reimplement get_cycles().]
On systems were for whatever reasons we can't use the cycle counter, fall
back to the c0_random register as an entropy source. It has however a
very small range that makes it suitable for random_get_entropy only and
not get_cycles.
This optimised version compiles to 8 instructions in the fast path even in
the worst case of all the conditions to check being variable (including a
MFC0 move delay slot that is only required for very old processors):
828: 8cf90000 lw t9,0(a3)
828: R_MIPS_LO16 jiffies
82c: 40057800 mfc0 a1,c0_prid
830: 3c0200ff lui v0,0xff
834: 00a21024 and v0,a1,v0
838: 1040007d beqz v0,a30 <add_interrupt_randomness+0x22c>
83c: 3c030000 lui v1,0x0
83c: R_MIPS_HI16 cpu_data
840: 40024800 mfc0 v0,c0_count
844: 00000000 nop
848: 00409021 move s2,v0
84c: 8ce20000 lw v0,0(a3)
84c: R_MIPS_LO16 jiffies
On most targets the sequence will be shorter and on some it will reduce to
a single `MFC0 <reg>,c0_count', as all MIPS architecture (i.e. non-legacy
MIPS) processors require the CP0 Count register to be present.
The only known exception that reports MIPS architecture compliance, but
contrary to that lacks CP0 Count is the Ingenic JZ4740 thingy. For broken
platforms like that this code requires cpu_has_counter to be hardcoded to
0 (i.e. no variable setting is permitted) so as not to penalise all the
other good platforms out there.
The asm barrier is required so that the compiler does not pull any
potentially costly (cold cache!) `cpu_data' variable access into the fast
path.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: John Crispin <blogic@openwrt.org>
Cc: Andrew McGregor <andrewmcgr@gmail.com>
Cc: Dave Taht <dave.taht@bufferbloat.net>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Simon Kelley <simon@thekelleys.org.uk>
Cc: Jim Gettys <jg@freedesktop.org>
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6702/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds initial support for BPF-JIT on MIPS
Tested on mips32 LE/BE and mips64 BE/n64 using
dhcp, ping and various tcpdump filters.
Benchmarking:
Assuming the remote MIPS target uses 192.168.154.181
as its IP address, and the local host uses 192.168.154.136,
the following results can be obtained using the following
tcpdump filter (catches no frames) and a simple
'time ping -f -c 1000000' command.
[root@(none) ~]# tcpdump -p -n -s 0 -i eth0 net 10.0.0.0/24 -d
(000) ldh [12]
(001) jeq #0x800 jt 2 jf 8
(002) ld [26]
(003) and #0xffffff00
(004) jeq #0xa000000 jt 16 jf 5
(005) ld [30]
(006) and #0xffffff00
(007) jeq #0xa000000 jt 16 jf 17
(008) jeq #0x806 jt 10 jf 9
(009) jeq #0x8035 jt 10 jf 17
(010) ld [28]
(011) and #0xffffff00
(012) jeq #0xa000000 jt 16 jf 13
(013) ld [38]
(014) and #0xffffff00
(015) jeq #0xa000000 jt 16 jf 17
(016) ret #65535
- BPF-JIT Disabled
real 1m38.005s
user 0m1.510s
sys 0m6.710s
- BPF-JIT Enabled
real 1m35.215s
user 0m1.200s
sys 0m4.140s
[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
It will be used later on by bpf-jit
[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6736/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It will be used later on by bpf-jit
[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6733/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It will be used later on by bpf-jit
[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6732/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It will be used later on by bpf-jit
[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6731/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It will be used later on by bpf-jit
[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6730/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It will be used later on by bpf-jit
[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6729/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It will be used later on by bpf-jit
[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: http://patchwork.linux-mips.org/patch/6728/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It will be used later on by bpf-jit
[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6727/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It will be used later on by bpf-jit
[ralf@linux-mips.org: Fixed conflict due to other preceeding conflicts.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6726/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix build errors when DEBUG is defined in arch/mips/kvm/.
- The DEBUG code in kvm_mips_handle_tlbmod() was missing some variables.
- The DEBUG code in kvm_mips_host_tlb_write() was conditional on an
undefined "debug" variable.
- The DEBUG code in kvm_mips_host_tlb_inv() accessed asid_map directly
rather than using kvm_mips_get_user_asid(). Also fixed brace
placement.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: Sanjay Lal <sanjayl@kymasys.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Expose two new virtual registers to userland via the
KVM_{GET,SET}_ONE_REG ioctls.
KVM_REG_MIPS_COUNT_CTL is for timer configuration fields and just
contains a master disable count bit. This can be used by userland to
freeze the timer in order to read a consistent state from the timer
count value and timer interrupt pending bit. This cannot be done with
the CP0_Cause.DC bit because the timer interrupt pending bit (TI) is
also in CP0_Cause so it would be impossible to stop the timer without
also risking a race with an hrtimer interrupt and having to explicitly
check whether an interrupt should have occurred.
When the timer is re-enabled it resumes without losing time, i.e. the
CP0_Count value jumps to what it would have been had the timer not been
disabled, which would also be impossible to do from userland with
CP0_Cause.DC. The timer interrupt also cannot be lost, i.e. if a timer
interrupt would have occurred had the timer not been disabled it is
queued when the timer is re-enabled.
This works by storing the nanosecond monotonic time when the master
disable is set, and using it for various operations instead of the
current monotonic time (e.g. when recalculating the bias when the
CP0_Count is set), until the master disable is cleared again, i.e. the
timer state is read/written as it would have been at that time. This
state is exposed to userland via the read-only KVM_REG_MIPS_COUNT_RESUME
virtual register so that userland can determine the exact time the
master disable took effect.
This should allow userland to atomically save the state of the timer,
and later restore it.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: David Daney <david.daney@cavium.com>
Cc: Sanjay Lal <sanjayl@kymasys.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The KVM_HOST_FREQ Kconfig symbol was used by KVM guest kernels to
override the timer frequency calculation to a value based on the host
frequency. Now that the KVM timer emulation is implemented independent
of the host timer frequency and defaults to 100MHz, adjust the working
of CONFIG_KVM_HOST_FREQ to match.
The Kconfig symbol now specifies the guest timer frequency directly, and
has been renamed accordingly to KVM_GUEST_TIMER_FREQ. It now defaults to
100MHz too and the help text is updated to make it clear that a zero
value will allow the normal timer frequency calculation to take place
(based on the emulated RTC).
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Sanjay Lal <sanjayl@kymasys.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Previously the emulation of the CPU timer was just enough to get a Linux
guest running but some shortcuts were taken:
- The guest timer interrupt was hard coded to always happen every 10 ms
rather than being timed to when CP0_Count would match CP0_Compare.
- The guest's CP0_Count register was based on the host's CP0_Count
register. This isn't very portable and fails on cores without a
CP_Count register implemented such as Ingenic XBurst. It also meant
that the guest's CP0_Cause.DC bit to disable the CP0_Count register
took no effect.
- The guest's CP0_Count register was emulated by just dividing the
host's CP0_Count register by 4. This resulted in continuity problems
when used as a clock source, since when the host CP0_Count overflows
from 0x7fffffff to 0x80000000, the guest CP0_Count transitions
discontinuously from 0x1fffffff to 0xe0000000.
Therefore rewrite & fix emulation of the guest timer based on the
monotonic kernel time (i.e. ktime_get()). Internally a 32-bit count_bias
value is added to the frequency scaled nanosecond monotonic time to get
the guest's CP0_Count. The frequency of the timer is initialised to
100MHz and cannot yet be changed, but a later patch will allow the
frequency to be configured via the KVM_{GET,SET}_ONE_REG ioctl
interface.
The timer can now be stopped via the CP0_Cause.DC bit (by the guest or
via the KVM_SET_ONE_REG ioctl interface), at which point the current
CP0_Count is stored and can be read directly. When it is restarted the
bias is recalculated such that the CP0_Count value is continuous.
Due to the nature of hrtimer interrupts any read of the guest's
CP0_Count register while it is running triggers a check for whether the
hrtimer has expired, so that the guest/userland cannot observe the
CP0_Count passing CP0_Compare without queuing a timer interrupt. This is
also taken advantage of when stopping the timer to ensure that a pending
timer interrupt is queued.
This replaces the implementation of:
- Guest read of CP0_Count
- Guest write of CP0_Count
- Guest write of CP0_Compare
- Guest write of CP0_Cause
- Guest read of HWR 2 (CC) with RDHWR
- Host read of CP0_Count via KVM_GET_ONE_REG ioctl interface
- Host write of CP0_Count via KVM_SET_ONE_REG ioctl interface
- Host write of CP0_Compare via KVM_SET_ONE_REG ioctl interface
- Host write of CP0_Cause via KVM_SET_ONE_REG ioctl interface
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: Sanjay Lal <sanjayl@kymasys.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When a VCPU is scheduled in on a different CPU, refresh the hrtimer used
for emulating count/compare so that it gets migrated to the same CPU.
This should prevent a timer interrupt occurring on a different CPU to
where the guest it relates to is running, which would cause the guest
timer interrupt not to be delivered until after the next guest exit.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: Sanjay Lal <sanjayl@kymasys.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
