Now that we have a driver for A31's RTC, enable it
in multi_v7_defconfig.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we have a driver for A31's RTC, enable it
in the default sunxi config.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This moves <mach/regs-clock.h> into mach-s5pv210 so no more
include/mach/ under mach-s5pv210.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Tomasz Figa <t.figa@samsung.com>
ARCH_EXYNOS doesn't select NEED_MACH_MEMORY_H, so <asm/memory.h> doesn't
include <mach/memory.h> and so this file is not used and can go away.
Signed-off-by: Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
[t.figa@samsung.com: boot tested on Exynos4412-based Trats2 board]
Tested-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Sachin Kamat <sachin.kamat@samsung.com>
[sachin.kamat: Tested on Arndale octa board (Exynos 5420)]
Tested-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
On i.MX6Q, gpu2d_axi and gpu3d_axi are either from AXI or
AHB clock, but on i.MX6DL, gpu2d_axi and gpu3d_axi are
from mmdc_ch0_axi_podf, and they can NOT be gated by mmdc_ch0_axi
's clock gate, the mux option register field(CCM_CBCMR)
is marked as "Reserved" now on i.MX6DL RM, so correct these
two clks setting.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Previous version had an extra 'fsl' which made the pins not match
any entry. The console message,
vf610-pinctrl 40048000.iomuxc: no fsl,pins property in node \
/soc/aips-bus@40000000/iomuxc@40048000/vf610-twr/esdhc1grp
is displayed without the fix. The prior version would generally
work as u-boot sets the pins properly for sdhc. This change allows
Linux sdhc use even if u-boot is built without sdhc support.
Signed-off-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Fixes: 0517fe6aa8 ("ARM: dts: vf610-twr: Add support for sdhc1")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Since ARCH_MXC already selects ARCH_HAS_OPP, it's really unnecessary for
SOC_IMX27 and SOC_IMX5 to select it again.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
After the suspend routine running in OCRAM puts DDR into self-refresh,
it will access IOMUXC block to float DDR IO for power saving. A TLB
missing of IOMUXC base address may happen in this case, and triggers an
access to DDR, and thus hangs the system.
The failure is discovered by running suspend/resume on a Cubox-i board.
Though the issue is not Cubox-i specific, it can be hit the on the board
quite easily with the 3.15 or 3.16 kernel.
Fix the issue with a dummy access to IOMUXC block at the beginning of
suspend routine, so that the address translation can be filled into TLB
before DDR is put into self-refresh.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Cc: <stable@vger.kernel.org>
Acked-by: Anson Huang <Anson.Huang@freescale.com>
My earlier patch 1fc593feaf ("ARM: imx: build i.MX6 functions
only when needed") fixed a problem with building an i.MX5 kernel,
but now the problem has returned for the case where we allow
ARMv6K SMP builds in multiplatform. With CONFIG_CPU_V7 disabled,
but i.MX3 and SMP enabled, we get this build error:
arch/arm/mach-imx/built-in.o: In function `v7_secondary_startup':
:(.text+0x5124): undefined reference to `v7_invalidate_l1'
This puts the code inside of an "ifdef CONFIG_SOC_IMX6" to hopefully
do the right thing in all configurations.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This adds pin-muxing info for the i2c controller / port combinations
which are known to be used on actual boards.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The card detect pin setting was taken from the original fex file,
and is confirmed to work.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add nodes for the 3 mmc controllers found on A23 SoCs to the sun8i DTSI.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This adds pin-muxing info for the mmc controller / port combinations
which are known to be used on actual boards.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The MMC module clocks on sun8i are the same as those found on
previous Allwinner SoCs, module 0 clocks.
This patch adds the clocks nodes to the dtsi with existing drivers.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we have R_PIO controller support and the pinmux for R_UART,
add the correct pinctrl properties to the R_UART node.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
R_UART is available on extra pads on certain tablets, which makes it
ideal for use as a console. Here we add the pins for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
uart0 on sun8i is only muxed with mmc0, which makes it a poor choice
for the console. However, some tablets only have pads for uart0
available on the circuit board.
Here we add the uart0 pinmux set for people who need it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we have a driver for the R_PIO controller,
add the corresponding device node to the dtsi.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we have a driver for the sun8i PIO controller,
add the corresponding device node to the dtsi.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
All of our SPI controllers support DMA transfers, so let's add the
properties here so they can be used when it's best to do so.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
All of our SPI controllers support DMA transfers, so let's add the
properties here so they can be used when it's best to do so.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
All of our SPI controllers support DMA transfers, so let's add the
properties here so they can be used when it's best to do so.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A20 SoC has a sun4i-compatible DMA controller. Let's add a node to
represent it on the device tree.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A10S and A13 SoCs have sun4i-compatible DMA controllers. Let's add
the corresponding nodes to represent them on the device tree.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we have a driver for sun6i's rtc hardware, add a device node
for it so we can use it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
sun8i shares the same rtc hardware as sun6i. Now that we have a driver
for it, add a device node to the DTSI for it so we can use it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
There's no legacy board anymore, genmai now boots with multiplatform
support only. Remove the leftovers.
Makefile.boot portion pointed out by Paul Bolle.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Wolfram Sang <wsa@sang-engineering.com>
Cc: Paul Bolle <pebolle@tiscali.nl>
[horms+renesas@verge.net.au: squashed in patch containing
Makefile.boot change]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the Lager board specific device node part for VIN1 (composite video in);
add the device node for Analog Devices ADV7180 video decoder to IIC2 bus.
Add the necessary subnodes to interconnect VIN1 and ADV7180 devices.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
[Sergei: rebased, edited changelog and summary]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
