Apparently, if G3D regulator is powered off, the SoC cannot enter low
power modes and just hangs. This patch fixes this by keeping the
regulator always on when the system is running, as suggested by Exynos 4
User's Manual in case of Exynos4210/4x12 SoCs (Exynos5250 UM does not
have such note, but observed behavior seems to confirm that it is true
for this SoC as well).
This fixes an issue preventing Arndale board from entering sleep mode
observed since commit
346f372f7b clk: exynos5250: Add CLK_IGNORE_UNUSED flag for pmu clock
that landed in kernel 3.10, which has fixed the clock driver to make the
SoC actually try to enter the sleep mode.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: <stable@vger.kernel.org> [v3.10+]
Tested-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
BMP085 EOC (End Of Conversion) irq line is connected to
gpio113 on gta04. Set irq properties to have driver using irq
instead polling for EOC.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The function is nearly empty and samsung_cpu_rev is static
so already 0 making the function obsolete, therefore remove
it.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Commit 48cf83dc(ARM: samsung: remove unused tick.h) removed some
occurences of tick.h. tick.h itself and s3c24xx_ostimer_pending
was only used by the old timer driver and is not used anymore.
Therefore remove the last 3 occurences.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
instead of using sirf specific dma channel property like "sirf,uart-dma-rx-channel"
and "sirf,uart-dma-tx-channel", here we move to use generic dma dt-binding to get
the channel like:
- sirf,uart-dma-rx-channel = <21>;
- sirf,uart-dma-tx-channel = <2>;
+ dmas = <&dmac1 5>, <&dmac0 2>;
+ dma-names = "rx", "tx";
and we move dma_request_channel() to dma_request_slave_channel(), we don't need to
call sirfsoc dma filter function sirfsoc_dma_filter_id() again.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Integrator/AP can be used with a logic module called
IM-PD1, which contains a few AMBA PrimeCell devices, one of which
is the PL061 GPIO controller. As the lines from this GPIO
controller are looped back to devices on the board itself and
provides resources back to it, we need to always have GPIO
and the PL061 driver available for other devices to work.
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The peripherals on the IM-PD1 has never really been able to
properly fire their IRQs to the main FPGA IRQ controller.
Cascade it properly and register interrupts for all the
devices in the array.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for a VIC to be cascaded off another IRQ.
On the Integrator/AP logical module IM-PD1 there is a VIC
cascaded off the central FPGA IRQ controller so this is
needed for that to work out.
In order for the plug-in board to be able to register all
the devices with their IRQs relative to the offset of the
base obtained for the cascaded VIC, the base IRQ number
is passed back to the caller.
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This atomic commit changes the Integrator clock implementation
and the machines to register clocks from the device tree and
use these instead of the previous hard-coded clocks.
In the clock implementation all hard-coded clocks and the
special initialization function call goes away, and is
replaced by two compatible strings for the two clocks
available on the core module.
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This enables support for the Spansion s25fl512s SPI FLASH on QSPI.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
[horms+renesas@verge.net.au: resolved conflict]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add SDHI0, SDHI1 and SDHI2 as platform devices to the
legacy Koelsch board code. Also include regulators that
are needed to control VCCQ and VDD.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to datasheet, i.MX6Q has setpoint of 852MHz
which is exclusive with 996MHz, the fuse map of speed_grading
defines the max speed of ARM, here we add this 852MHz
setpoint opp info, kernel will check the speed_grading
fuse and remove all illegal setpoints.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
PCA-100 module cannot be used standalone. This patch renames
module file to .dtsi and excludes it from compilation.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
When booting secondary CPU(s) which are not yet powergated, a wrong
check lead to a timeout after 100 jiffies. With this patch, we only
delay powergating if CPUs are still not powered yet.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
h3xxx_init_gpio() behaves alsmost like gpio_request_array. Also after
all GPIO refactoring it is unused. Drop it now.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Both h3100 and h3600 request UART gpios during init_machine time. As
sa1100 gpio driver is going to become proper machine driver, move gpio
handling to UART port functions. Request all gpios using gpio_request
array once and then guard them from rerequesting with bool variable.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds the definitions for the BCM2835 I2S driver
to the device tree. Some GPIO settings are needed for
the correct pin functions.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
[swarren: fixed DT node sort order, simplified DT label name, removed
RPI .dts file changs, since use of I2S is a user-added option.]
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
This adds the definitions for the BCM2835 dmaengine driver
to the device tree. The dma-channel-mask is currently
fixed. Later it should be set via the firmware.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
[swarren, fixed DT node sort order]
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
The following patch enables performance counter support on Raspberry-Pi.
We have this working on the 2708 based rasp-pi kernels by manually putting
the device registration in the platform files.
This change does things properly in a device tree. The boot messages look
proper, but my rasp-pi hangs somewhere in USB enabling when running a
stock 3.13-rc6 kernel so I have been unable to fully test this change.
I also understand that the rasp-pi 1176 pmu support is missing the
overflow interrupt. I'm not sure if that's true of all 2835
implementations. If not, then this patch will need to be changed a bit.
Signed-off-by: Vince Weaver <vincent.weaver@maine.edu>
[swarren, fixed DT node sort order]
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Implement support for the Krait CPU release sequence when the
CPUs are part of the second version of the Krait processor
subsystem.
Signed-off-by: Rohit Vaswani <rvaswani@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Implement support for the Krait CPU release sequence when the
CPUs are part of the first version of the krait processor
subsystem.
Signed-off-by: Rohit Vaswani <rvaswani@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
This makes it easy to add SMP support for new devices by keying
on a device node for the release sequence. We add the
enable-method property for the cpus property to specify that we
want to use the gcc-msm8660 release sequence (which is going to
look for the global clock controller device node to map some
Scorpion specific power and control registers). We also remove
the nr_cpus detection code as that is done generically in the DT
CPU detection code.
Signed-off-by: Rohit Vaswani <rvaswani@codeaurora.org>
[sboyd: Port to CPU_METHOD_OF_DECLARE]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
The goal of multi-platform kernels is to remove the need for mach
directories and machine descriptors. To further that goal,
introduce CPU_METHOD_OF_DECLARE() to allow cpu hotplug/smp
support to be separated from the machine descriptors.
Implementers should specify an enable-method property in their
cpus node and then implement a matching set of smp_ops in their
hotplug/smp code, wiring it up with the CPU_METHOD_OF_DECLARE()
macro. When the kernel is compiled we'll collect all the
enable-method smp_ops into one section for use at boot.
At boot time we'll look for an enable-method in each cpu node and
try to match that against all known CPU enable methods in the
kernel. If there are no enable-methods in the cpu nodes we
fallback to the cpus node and try to use any enable-method found
there. If that doesn't work we fall back to the old way of using
the machine descriptor.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Pull networking updates from David Miller:
1) Fix flexcan build on big endian, from Arnd Bergmann
2) Correctly attach cpsw to GPIO bitbang MDIO drive, from Stefan Roese
3) udp_add_offload has to use GFP_ATOMIC since it can be invoked from
non-sleepable contexts. From Or Gerlitz
4) vxlan_gro_receive() does not iterate over all possible flows
properly, fix also from Or Gerlitz
5) CAN core doesn't use a proper SKB destructor when it hooks up
sockets to SKBs. Fix from Oliver Hartkopp
6) ip_tunnel_xmit() can use an uninitialized route pointer, fix from
Eric Dumazet
7) Fix address family assignment in IPVS, from Michal Kubecek
8) Fix ath9k build on ARM, from Sujith Manoharan
9) Make sure fail_over_mac only applies for the correct bonding modes,
from Ding Tianhong
10) The udp offload code doesn't use RCU correctly, from Shlomo Pongratz
11) Handle gigabit features properly in generic PHY code, from Florian
Fainelli
12) Don't blindly invoke link operations in
rtnl_link_get_slave_info_data_size, they are optional. Fix from
Fernando Luis Vazquez Cao
13) Add USB IDs for Netgear Aircard 340U, from Bjørn Mork
14) Handle netlink packet padding properly in openvswitch, from Thomas
Graf
15) Fix oops when deleting chains in nf_tables, from Patrick McHardy
16) Fix RX stalls in xen-netback driver, from Zoltan Kiss
17) Fix deadlock in mac80211 stack, from Emmanuel Grumbach
18) inet_nlmsg_size() forgets to consider ifa_cacheinfo, fix from Geert
Uytterhoeven
19) tg3_change_mtu() can deadlock, fix from Nithin Sujir
20) Fix regression in setting SCTP local source addresses on accepted
sockets, caused by some generic ipv6 socket changes. Fix from
Matija Glavinic Pecotic
21) IPPROTO_* must be pure defines, otherwise module aliases don't get
constructed properly. Fix from Jan Moskyto
22) IPV6 netconsole setup doesn't work properly unless an explicit
source address is specified, fix from Sabrina Dubroca
23) Use __GFP_NORETRY for high order skb page allocations in
sock_alloc_send_pskb and skb_page_frag_refill. From Eric Dumazet
24) Fix a regression added in netconsole over bridging, from Cong Wang
25) TCP uses an artificial offset of 1ms for SRTT, but this doesn't jive
well with TCP pacing which needs the SRTT to be accurate. Fix from
Eric Dumazet
26) Several cases of missing header file includes from Rashika Kheria
27) Add ZTE MF667 device ID to qmi_wwan driver, from Raymond Wanyoike
28) TCP Small Queues doesn't handle nonagle properly in some corner
cases, fix from Eric Dumazet
29) Remove extraneous read_unlock in bond_enslave, whoops. From Ding
Tianhong
30) Fix 9p trans_virtio handling of vmalloc buffers, from Richard Yao
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (136 commits)
6lowpan: fix lockdep splats
alx: add missing stats_lock spinlock init
9p/trans_virtio.c: Fix broken zero-copy on vmalloc() buffers
bonding: remove unwanted bond lock for enslave processing
USB2NET : SR9800 : One chip USB2.0 USB2NET SR9800 Device Driver Support
tcp: tsq: fix nonagle handling
bridge: Prevent possible race condition in br_fdb_change_mac_address
bridge: Properly check if local fdb entry can be deleted when deleting vlan
bridge: Properly check if local fdb entry can be deleted in br_fdb_delete_by_port
bridge: Properly check if local fdb entry can be deleted in br_fdb_change_mac_address
bridge: Fix the way to check if a local fdb entry can be deleted
bridge: Change local fdb entries whenever mac address of bridge device changes
bridge: Fix the way to find old local fdb entries in br_fdb_change_mac_address
bridge: Fix the way to insert new local fdb entries in br_fdb_changeaddr
bridge: Fix the way to find old local fdb entries in br_fdb_changeaddr
tcp: correct code comment stating 3 min timeout for FIN_WAIT2, we only do 1 min
net: vxge: Remove unused device pointer
net: qmi_wwan: add ZTE MF667
3c59x: Remove unused pointer in vortex_eisa_cleanup()
net: fix 'ip rule' iif/oif device rename
...
Instead of harcoding 0 and 1 for the gpio specifications in the Armada
370/XP boards, use the <dt-bindings/gpio/gpio.h> header file and its
GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW definitions.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The ->map_io() implementation of Armada 370/XP simply calls
debug_ll_io_init(), which is exactly what the kernel does when
->map_io is NULL. Therefore, there is no need to have a specific
->map_io() implementation in Armada 370/XP.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Instead of the of_find_matching_node()/of_match_node() pair, which requires two
iterations through the match table, make use of of_find_matching_node_and_match(),
which only iterates through the table once.
While we're here, mark the of_system_controller table const.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
With the merge of the Kirkwood support into arch/arm/mach-mvebu/, the
mvebu platform will no longer only contain ARMv7 compatible processors
(Armada 370, Armada XP, and soon Armada 375, Armada 38x and Dove), but
also ARMv5 compatible processors (Kirkwood, and hopefully Orion5x in
the future).
However, a single mvebu_defconfig cannot work, since it is not
possible to build a kernel that supports both ARMv5 and ARMv7
platforms in the same binary. As a consequence, this commit renames
mvebu_defconfig to mvebu_v7_defconfig, which is the configuration that
will build a kernel that supports all ARMv7 mvebu platforms. As
Kirkwood support gets merged into mach-mvebu, an additional
mvebu_v5_defconfig will be added.
Even though we already have a multi_v7_defconfig, the mvebu developers
found it more convenient for development to have a defconfig that
builds only the mvebu platforms.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Commit 70b41abc15
"ARM: ux500: move MSP pin control to the device tree"
accidentally activated MSP2, giving rise to a boot scroll
scream as the kernel attempts to probe a driver for it and
fails to obtain DMA channel 14.
Fix this up by marking the node disabled again.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
This patch replaces custom lcd_power() callback with
regulator API over LCD class.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
GFP_ATOMIC is not a single gfp flag, but a macro which expands to the other
flags and LACK of __GFP_WAIT flag. To check if caller wanted to perform an
atomic allocation, the code must test __GFP_WAIT flag presence. This patch
fixes the issue introduced in v3.6-rc5
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: stable@vger.kernel.org
Recent changes to the pwm-backlight driver have made the power supply
mandatory. There is code in the regulator core to deal with situations
where no regulator is specified and provide a dummy, but that works on
DT-based boards only.
The situation can be remedied by adding a dummy regulator during board
initialization.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
The address for control regs in clkvcp3 node is not correct and should
be 0x023500a8 instead of 0x0235000a8.
This lead to few unexpected behaviors while clocks were turned
of in absence of clk_ignore_unused
Mike Turquette <mturquette@linaro.org>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
All Allwinner A20 boards we support can only use either EMAC or GMAC,
as they share the same pins. As we have switched all supported to
GMAC, we should alias GMAC (the active controller) as ethernet0,
so u-boot will insert the MAC address for the correct controller.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
GMAC has better performance and fewer hardware issues.
Use the GMAC in MII mode for ethernet instead of the EMAC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
GMAC has better performance and fewer hardware issues.
Use the GMAC in MII mode for ethernet instead of the EMAC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
