OMAP2430 I2CHS modules require specific hardware ops to be used, so added
a new compatible string for this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
OMAP2 has slightly different DPLL compared to later OMAP generations.
This patch adds support for the ti,omap2-dpll-core-clock and also adds
the bindings documentation.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add "power-source" property to generic options used for DT parsing files.
This enables drivers, which use generic pin configurations, to get the
value passed to this property.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make the boot console available to more m68k platforms by leveraging
the head.S debug console.
The boot console is enabled by the "earlyprintk" command line argument
which is how most other architectures do this.
This is a change of behaviour for the Mac but does not negatively impact
the common use-case which is not debugging.
This is also a change of behaviour for other platforms because it means
the serial port stays quiet when CONFIG_EARLY_PRINTK is not enabled. This
is also an improvement for the common use-case.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Stephen N Chivers <schivers@csc.com.au>
[Geert: CONSOLE_DEBUG should depend on CONFIG_FONT_SUPPORT]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Some oscillators can be turned off during off-idle saving few
a little bit power at the cost of the oscillator start up
latency.
If you board can do this, you can now enable it by using the
ti,twl4030-power-idle-osc-off compatible flag.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
These settings are based on the "Recommended Sleep Sequences for
the Zoom Platform".
The settings assume most of the regulators are under control of
Linux, and twl4030 only cuts off VDD1 and VDD2 during off-idle as
Linux cannot do it.
For any board specific changes to these, let's patch them in as
changes to the generic data in the follow-up patches. This keeps
the board specific changes small.
Note that this does not consider the twl5030 errata 27 and 28.
That can be added later on after it has been tested. For more
information about errata 27 and 28.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The twl4030 PMIC needs to be configured properly for things like
warm reset and deeper idle states so the PMIC manages the regulators
properly based on the hardware triggers from the SoC. Earlier
we have configured twl4030 using platform data, but we want to
do it for device tree based booting also.
In some cases configuring twl4030 is needed for things to work.
For example, when rebooting an OMAP3530 at 125 MHz, it hangs.
With this patch, TWL4030 will be reset when a warm reset occures,
and OMAP3530 does not hang on reboot.
Let's add device tree support and configure things for warm reset
as the default when compatible = "ti,twl4030-power". More
complicated configurations can be added to the driver based on
other compatible flags.
Note we now also make the pdata const like it should be.
This allows use it for match->data with the device tree
related functions.
Based on earlier patch by Matthias Brugger <matthias.bgg@gmail.com>
and Lesly A M <leslyam@ti.com>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add some documentation about ...
/sys/devices/system/cpu/dscr_default
/sys/devices/system/cpu/cpuN/dscr
... to Documentation/ABI/stable.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
USB3503 chip supports 8 values of reference clock. The value is
specified by REF_SEL[1:0] pins and INT_N line. This patch add support
for getting 'refclk' clock, enabling it and setting INT_N line according
to the value of the gathered clock. If no clock has been specified,
driver defaults to the old behaviour (assuming that clock has been
specified by REF_SEL pins from primary reference clock frequencies
table).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit extends the compatible string list of the xhci-platform
binding with the new "armada-375-xhci" and "armada-380-xhci"
compatible strings. It is used to describe the XHCI controller which
is available in the Armada 375 and 38x SoCs.
It also indicates that an optional 'clocks' property is now supported.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit updates the Device Tree binding documentation of
ehci-orion to take into account the fact that we can now optionally
pass a clock and a PHY reference.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the phy provider, supplied by new Exynos-usb2phy using
Generic phy framework.
Keeping the support for older USB phy intact right now, in order
to prevent any functionality break in absence of relevant
device tree side change for ehci-exynos.
Once we move to new phy in the device nodes for ehci, we can
remove the support for older phys.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
[gautam.vivek@samsung.com: Addressed review comments from mailing list]
[gautam.vivek@samsung.com: Kept the code for old usb-phy, and just
added support for new exynos5-usb2phy in generic phy framework]
[gautam.vivek@samsung.com: Edited the commit message]
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support to consume phy provided by Generic phy framework.
Keeping the support for older usb-phy intact right now, in order
to prevent any functionality break in absence of relevant
device tree side change for ohci-exynos.
Once we move to new phy in the device nodes for ohci, we can
remove the support for older phys.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Applications can submit a set of commands in one packet to the kernel,
and in some cases it is required such as reading the temperature
sensor results. This adds an option W1_CN_BUNDLE to the flags of
cn_msg to request the kernel to reply in one packet for efficiency.
The cn_msg flags now check for unknown flag values and return an error
if one is seen. See "Proper handling of unknown flags in system
calls" http://lwn.net/Articles/588444/
This corrects the ack values returned as per the protocol standard,
namely the original ack for status messages and seq + 1 for all others
such as the data returned from a read.
Some of the common variable names have been standardized as follows.
struct cn_msg *cn
struct w1_netlink_msg *msg
struct w1_netlink_cmd *cmd
struct w1_master *dev
When an argument and a function scope variable would collide, add req_
to the argument.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This increases the amount of bundling to reduce the number of packets
sent. For the one wire use there can be multiple struct
w1_netlink_cmd in a struct w1_netlink_msg and multiple of those in
struct cn_msg, and with this change multiple of those in a struct
nlmsghdr, and at each level the len identifies there being multiple of
the next.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
irqchip core changes for v3.16 collected by Jason Cooper:
- irq-gic: Use a mask field
- irq-armada-370-xp: Move the DT binding docs to the irqchip directory
- irq-brcmstb-l2: New driver for Broadcom Set Top Box Level-2
Changed for the 3.16 merge window.
This includes KVM support for PSCI v0.2 and also includes generic Linux
support for PSCI v0.2 (on hosts that advertise that feature via their
DT), since the latter depends on headers introduced by the former.
Finally there's a small patch from Marc that enables Cortex-A53 support.
The main pll controller used to drive theC66x CorePacs, the switch fabric,
and a majority of the peripheral clocks (all but the ARM CorePacs, DDR3 and
the NETCP modules) requires a PLL Controller to manage the various clock
divisions, gating, and synchronization.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
[santosh.shilimkar@ti.com: Fixed the subject line]
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This node is intended to allow SoC reset in case of software reset
or appropriate watchdogs.
The Keystone SoCs can contain up to 4 watchdog timers to reset
SoC. Each watchdog timer event input is connected to the Reset Mux
block. The Reset Mux block can be configured to cause reset or not.
Additionally soft or hard reset can be configured.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
[santosh.shilimkar@ti.com: Fixed the subject line]
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
* dma-api:
iommu/exynos: Remove unnecessary "&" from function pointers
DMA-API: Update dma_pool_create ()and dma_pool_alloc() descriptions
DMA-API: Fix duplicated word in DMA-API-HOWTO.txt
DMA-API: Capitalize "CPU" consistently
sh/PCI: Pass GAPSPCI_DMA_BASE CPU & bus address to dma_declare_coherent_memory()
DMA-API: Change dma_declare_coherent_memory() CPU address to phys_addr_t
DMA-API: Clarify physical/bus address distinction
* pci/virtualization:
PCI: Mark RTL8110SC INTx masking as broken
* pci/msi:
PCI/MSI: Remove pci_enable_msi_block()
* pci/misc:
PCI: Remove pcibios_add_platform_entries()
s390/pci: use pdev->dev.groups for attribute creation
PCI: Move Open Firmware devspec attribute to PCI common code
* pci/resource:
PCI: Add resource allocation comments
PCI: Simplify __pci_assign_resource() coding style
PCI: Change pbus_size_mem() return values to be more conventional
PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources
PCI: Support BAR sizes up to 8GB
resources: Clarify sanity check message
PCI: Don't add disabled subtractive decode bus resources
PCI: Don't print anything while decoding is disabled
PCI: Don't set BAR to zero if dma_addr_t is too small
PCI: Don't convert BAR address to resource if dma_addr_t is too small
PCI: Reject BAR above 4GB if dma_addr_t is too small
PCI: Fail safely if we can't handle BARs larger than 4GB
x86/gart: Tidy messages and add bridge device info
x86/gart: Replace printk() with pr_info()
x86/PCI: Move pcibios_assign_resources() annotation to definition
x86/PCI: Mark ATI SBx00 HPET BAR as IORESOURCE_PCI_FIXED
x86/PCI: Don't try to move IORESOURCE_PCI_FIXED resources
x86/PCI: Fix Broadcom CNB20LE unintended sign extension
Use "boundary" to be more descriptive than "alloc" in the dma_pool_create()
documentation.
Replace "SLAB_KERNEL" and "SLAB_ATOMIC" with the correct "GFP_KERNEL" and
"GFP_ATOMIC."
[bhelgaas: changelog]
Signed-off-by: Gioh Kim <gioh.kim@lge.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
"coherent" is written twice when it should be just once.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Sometimes we used "cpu," other times "CPU." Use "CPU" consistently.
Suggested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Merge "DaVinci EDMA clean-up for v3.16" from Sekhar Nori:
This series makes edma use configuration information available within
the IP instead of reading it from platform data or DT. Some other useful
clean-ups are included too.
* tag 'davinci-for-v3.16/edma' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci: (34 commits)
ARM: edma: Remove redundant/unused parameters from edma_soc_info
ARM: davinci: Remove redundant/unused parameters for edma
ARM: dts: am4372: Remove obsolete properties from edma node
ARM: dts: am33xx: Remove obsolete properties from edma node
dt/bindings: ti,edma: Remove redundant properties from documentation
ARM: edma: Get IP configuration from HW (number of channels, tc, etc)
ARM: edma: Save number of regions from pdata to struct edma
ARM: edma: Remove num_cc member from struct edma
ARM: edma: Remove queue_tc_mapping data from edma_soc_info
ARM: davinci: Remove eDMA3 queue_tc_mapping data from edma_soc_info
ARM: edma: Do not change TC -> Queue mapping, leave it to default.
ARM: edma: Take the number of tc from edma_soc_info (pdata)
ARM: edma: No need to clean the pdata in edma_of_parse_dt()
ARM: edma: Clean up and simplify the code around irq request
dmaengine: edma: update DMA memcpy to use new param element
dmaengine: edma: Document variables used for residue accounting
dmaengine: edma: Provide granular accounting
dmaengine: edma: Make reading the position of active channels work
dmaengine: edma: Store transfer data in edma_desc and edma_pset
dmaengine: edma: Create private pset struct
...
Signed-off-by: Olof Johansson <olof@lixom.net>
The patch fixes EDMA crossbar mapping to actually
make it work. The patch has been tagged for stable.
* tag 'davinci-fixes-for-v3.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: common: edma: Fix xbar mapping
Merge "ARM: berlin: SoC changes for v3.16" from Sebastian Hesselbart:
Despite relatively young Berlin SoC support, we already have support
for a BG2Q SoC provided by Alexandre Belloni and Antoine Tenart. Also,
we gained support for DW gpio and a pinctrl driver.
* tag 'berlin-soc-3.16' of https://github.com/shesselba/linux-berlin:
ARM: berlin: add the pinctrl dependency for the Marvell Berlin SoCs
ARM: berlin: add the LIBGPIO as a dependency for the BG2Q
ARM: berlin: add MACH_BERLIN_BG2Q symbol
ARM: berlin: add Marvell Armada 1500 pro to Marvell doc
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: berlin: DT changes for v3.16" from Sebastian Hesselbart:
Quite a lot changes but it looks like DT approach is really paying off.
BG2Q joins Berlin SoC family with corresponding development board, DW
gpio nodes for all SoCs. Most notably, we have settled clock bindings
to allow us to continue on drivers requiring clocks and pinctrl bindings.
Last but not least, BG2Q gained SDHCI support and is able to properly
boot into userspace.
* tag 'berlin-dt-3.16' of https://github.com/shesselba/linux-berlin:
ARM: dts: berlin: enable SD card reader and eMMC for the BG2Q DMP
ARM: dts: berlin: add the SDHCI nodes for the BG2Q
ARM: dts: berlin: add the pinctrl node and muxing setup for uarts
dt-binding: ARM: add pinctrl binding docs for Marvell Berlin2 SoCs
ARM: dts: berlin: convert BG2Q to DT clock nodes
ARM: dts: berlin: convert BG2 to DT clock nodes
ARM: dts: berlin: convert BG2CD to DT clock nodes
clk: berlin: add binding include for Berlin SoC clock ids
dt-binding: ARM: add clock binding docs for Marvell Berlin2 SoCs
ARM: dts: berlin: add the BG2CD GPIO nodes
ARM: dts: berlin: add the BG2 GPIO nodes
ARM: dts: berlin: add the BG2Q GPIO nodes
ARM: dts: berlin: add scu and chipctrl device nodes for BG2/BG2Q
ARM: dts: berlin: add the Marvell BG2-Q DMP device tree
ARM: dts: berlin: add the Marvell Armada 1500 pro
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: omap l3-noc bus driver changes for v3.16 merge window, resend" from
Tony Lindgren:
Improvments to omap l3-noc bus driver for v3.16 merge window
to add support for am347x and dra7.
* tag 'omap-for-v3.16/l3-noc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (25 commits)
bus: omap_l3_noc: Add AM4372 interconnect error data
bus: omap_l3_noc: Add DRA7 interconnect error data
bus: omap_l3_noc: introduce concept of submodule
bus: omap_l3_noc: Add information about the context of operation
bus: omap_l3_noc: add information about the type of operation
bus: omap_l3_noc: ignore masked out unclearable targets
bus: omap_l3_noc: improve readability by using helper for slave event parsing
bus: omap_l3_noc: make error reporting and handling common
bus: omap_l3_noc: fix masterid detection
bus: omap_l3_noc: convert flagmux information into a structure
bus: omap_l3_noc: use of_match_data to pick up SoC information
bus: omap_l3_noc: Add support for discountinous flag mux input numbers
bus: omap_l3_noc: convert target information into a structure
bus: omap_l3_noc: move L3 master data structure out
bus: omap_l3_noc: un-obfuscate l3_targ address computation
bus: omap_l3_noc: switch over to relaxed variants of readl/writel
bus: omap_l3_noc: populate l3->dev and use it
bus: omap_l3_noc: remove iclk from omap_l3 struct
bus: omap_l3_noc: rename functions and data to omap_l3
bus: omap_l3_noc: Fix copyright information
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: omap dt changes for v3.16 merge window, part 2" From Tony Lindgren:
Device tree related changes for omaps.
* tag 'omap-for-v3.16/dt-part2-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (49 commits)
ARM: dts: Enable mcpdm and mcbsp1 on DuoVero
ARM: dts: Convert DuoVero Parlor to use IOPAD macro
ARM: dts: am43xx: fix starting offset of NAND.filesystem MTD partition
ARM: dts: dra7: add support for parallel NAND flash
ARM: dts: am437x-gp-evm: Add ethernet support for GP EVM
ARM: dts: am4372: Add cpsw phy sel dt node
ARM: OMAP2+: Use pdata quirks for wl12xx on VAR-STK/DVK-OM44
ARM: dts: Add VAR-SOM-OM44 WLAN nodes
ARM: dts: Add support for OMAP4 VAR-DVK-OM44
ARM: dts: Add support for OMAP4 Variscite OM44 family
ARM: dts: Change IOPAD macro's for OMAP4/5
ARM: dts: AM33XX: fix ethernet and mdio default state
ARM: dts: am4372: Add hdq device tree data
ARM: omap2+: skip device build from platform code for dt
dts: dra7-evm: add USB support
ARM: dts: dra7: Add USB related nodes
ARM: dts: dra7-clock: Add "l3init_960m_gfclk" clock gate
ARM: dts: omap4+: Add clocks to USB2 PHY node
ARM: dts: dra7: add OCP2SCP3 and SATA nodes
ARM: dts: omap5: add sata node
...
Signed-off-by: Olof Johansson <olof@lixom.net>
With the newly introduced CPU_METHOD_OF_DECLARE is not necessary anymore
to reference the relevant smp_ops in the board file, but instead it can
simply be set by the enable-method property of the cpu nodes.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
If master clock is provided through device tree, then update
the master clock frequency during set_sysclk.
Documentation has been updated to reflect the change.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
If master clock is provided through device tree, then update
the master clock frequency during set_sysclk.
Documentation has been updated to reflect the change.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds the device tree binding documentation for Linear
Technology LTC3589, LTC3589-1, and LTC3589-2 8-port regulators.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add Linear Technology Corporation to the list of device tree vendor prefixes.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Renesas sound driver is supporting to use DMAEngine.
But, DMA slave channel name "tx", "rx" is not enough
in DT case.
Becuase, it has many ports and path combination.
This patch adds rsnd_dma_of_name() to find
DMA channel name, for example
memory to SSI0 is "mem_ssi0",
SSI0 to memory is "ssi0_mem",
SSI0 to SRC0 is "ssi0_src0",
SRC0 to SSI0 is "src0_ssi0",
SRC0 to DVC0 is "src0_dvc0"...
Renesas sound want to use PIO transfer mode for some reasons.
It will be PIO tranfer mode if device node doesn't have
DMA settings.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some platforms require that the codecs mclk is a fixed multiplication
factor of the audio stream rate. Add a optional property to the
binding to hold this factor and implement a hw_params() function to
make use of it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Mark Brown <broonie@linaro.org>
On some systems the platform doesn't support neither
PM_SUSPEND_MEM nor PM_SUSPEND_STANDBY, so PM_SUSPEND_FREEZE is the
only available system sleep state. However, some user space frameworks
only use the "mem" and (sometimes) "standby" sleep state labels, so
the users of those systems need to modify user space in order to be
able to use system suspend at all and that is not always possible.
For this reason, add a new kernel command line argument,
relative_sleep_states, allowing the users of those systems to change
the way in which the kernel assigns labels to system sleep states.
Namely, for relative_sleep_states=1, the "mem", "standby" and "freeze"
labels will enumerate the available system sleem states from the
deepest to the shallowest, respectively, so that "mem" is always
present in /sys/power/state and the other state strings may or may
not be presend depending on what is supported by the platform.
Update system sleep states documentation to reflect this change.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
