For v3.14 and prior, 1-bit Hamming code ECC via software was the
default choice for some boards e.g. 3430sdp.
Commit ac65caf514 in v3.15 changed the behaviour
to use 1-bit Hamming code via Hardware using a different ECC layout
i.e. (ROM code layout) than what is used by software ECC.
This ECC layout change causes NAND filesystems created in v3.14
and prior to be unusable in v3.15 and later. So don't mark "sw" scheme
as deperecated and support it.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Setting dp M2/N2 values plus state checker support (Vandana Kannan)
- chv power well support (Ville)
- DP training pattern 3 support for chv (Ville)
- cleanup of the hsw/bdw ddi pll code, prep work for skl (Damien)
- dsi video burst mode support (Shobhit)
- piles of other chv fixes all over (Ville et. al.)
- cleanup of the ddi translation tables setup code (Damien)
- 180 deg rotation support (Ville & Sonika Jindal)
* tag 'drm-intel-next-2014-08-08' of git://anongit.freedesktop.org/drm-intel: (59 commits)
drm/i915: Update DRIVER_DATE to 20140808
drm/i915: No busy-loop wait_for in the ring init code
drm/i915: Add sprite watermark programming for VLV and CHV
drm/i915: Round-up clock and limit drain latency
drm/i915: Generalize drain latency computation
drm/i915: Free pending page flip events at .preclose()
drm/i915: clean up PPGTT checking logic
drm/i915: Polish the chv cmnlane resrt macros
drm/i915: Hack to tie both common lanes together on chv
drm/i915: Add cherryview_update_wm()
drm/i915: Update DDL only for current CRTC
drm/i915: Parametrize VLV_DDL registers
drm/i915: Fill out the FWx watermark register defines
drm: Resetting rotation property
drm/i915: Add rotation property for sprites
drm: Add rotation_property to mode_config
drm/i915: Make intel_plane_restore() return an error
drm/i915: Add 180 degree sprite rotation support
drm/i915: Introduce a for_each_intel_encoder() macro
drm/i915: Demote the DRRS messages to debug messages
...
Jonathan writes:
1st round of new IIO drivers, functionality and cleanups for the 3.18 cycle.
Maintainer Updates
* Add 3 designated reviewers for IIO. Lars, Peter and Hartmut have been
actively reviewing a lot of patches for a while now so this reflects
the status quo. These three are probably the only reason I keep
my head above the water!
New drivers and device support
* max5821 DAC
* Rockchip SARADC
* TI ADC128S052 ADC
* BMC150 Accelerometer
* exynos ADC driver gains support for s3c24xx and s3c64xx parts.
* kxcjk-1013 gainst range control and runtime PM support to drive
down it's power usage.
Driver removals
* Drop ad5930, ad99850, ad9852, ad9910 and ad9951 drivers on the simple
basis that they drivers just provided a register write function with
no compliant user space ABI whatsoever. Much better to drop them and
start again for these in the fullness of time.
Core Enhancements
* Join together neighbouring elements in the demux units that feeds
the binary interfaces. This cuts down on the number of individual
copies needed when splitting out individual channels from the incoming
channel scans.
* Other demux related cleanups such as using roundup instead of a local
implementation.
Cleanups
* Drop an unnecessary double setting of the owner field in xilinx adc.
* Some more patches to use managed (devm) interfaces to cut down on
complexity of removal code.
* adis16060 coding style fixlets.
* Fix some incorrect error returns in the Xilinx ADC driver.
* Coding style fixlets for various accelerometer drivers.
* Some sparse warning fixes to do with endianness and sign of variables.
* Fix an incorrect and entirely pointless use of sizeof on a dynamic pointer
in hid-sensor-magn-3d by dropping the relevant code.
Pull AT91 reset, poweroff and ram drivers from Maxime Ripard:
"This tag holds the various new drivers introduced to move code that used to be
in mach-at91 over to the proper frameworks.
These files are the reboot and poweroff code for all AT91 SoCs but the RM9200,
and the ram controller driver is not doing much at the time, except for grabing
the RAM clock in order to leave it always enabled."
Conflicts:
arch/arm/mach-at91/Kconfig
This patch clarifies that kvm_dirty_regs are just a hint to the kernel and
that the kernel might just ignore some flags and sync the values (like done for
acrs and gprs now).
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Remove legacy bits, refer people to hid-transport.txt and add descriptions
for all new features.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull x86 fixes from Ingo Molnar:
"A couple of EFI fixes, plus misc fixes all around the map"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/arm64: Store Runtime Services revision
firmware: Do not use WARN_ON(!spin_is_locked())
x86_32, entry: Clean up sysenter_badsys declaration
x86/doc: Fix the 'tlb_single_page_flush_ceiling' sysconfig path
x86/mm: Fix sparse 'tlb_single_page_flush_ceiling' warning and make the variable read-mostly
x86/mm: Fix RCU splat from new TLB tracepoints
Marc Kleine-Budde says:
====================
pull-request: can-next 2014-08-20
this is a pull request of 10 patches for net-next/master.
There is one patch by Wolfram Sang to clean up the build system.
Two patches by Stefan Agner that add vf610 support to the flexcan
driver. Dong Aisheng add support for bosch's m_can core, which is found
in the new freescale ARM SoCs. Sergei Shtylyov improves the rcar_can
driver by supporting all input clocks and adding device tree support.
The next patch is a small cleanup for the bit rate calculation function
by Lad, Prabhakar. And finally a patch by Himangi Saraogi, which
converts the mcp251x driver to use dmam_alloc_coherent.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds fix_mac_speed() support for
Altera socfpga Ethernet controller. Emac splitter is a
soft IP core in FPGA system that converts GMII interface from
Synopsys mac to RGMII/SGMII interface. This splitter core is
an optional IP if user would like to use RGMII/SGMII
interface in their system. Software needs to update a register
in splitter core when there is speed change.
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull EFI fixes from Matt Fleming:
* WARN_ON(!spin_is_locked()) always triggers on non-SMP machines.
Swap it for the more canonical lockdep_assert_held() which always
does the right thing - Guenter Roeck
* Assign the correct value to efi.runtime_version on arm64 so that all
the runtime services can be invoked - Semen Protsenko
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The order of the last two fields in the G/S_EDID specification was swapped from
what is in the actual struct. Fix this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In many cases the test pattern has selectable values for each colour
component. Implement controls for raw bayer components. Additional controls
should be defined for colour components that are not covered by these
controls.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The example in the binding document indicates that interrupt 32 is used
for the TLMM summary IRQ. Correct this to reduce the confusion.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add theory of operation notes to intel_lrc.c and comments to externally
visible functions.
v2: Add notes on logical ring context creation.
v3: Use kerneldoc.
v4: Integrate it in the DocBook template.
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com> (v1)
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com> (v2, v3)
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Drop hunk about render ring init function since that's not
yet merged.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The same FTM PWM device can have a different endianness on different
SoCs. The device tree provides a property to describing this so that an
operating system device driver can handle all variants of the device.
Refer to the table below for the endianness of the FTM PWM block as
integrated into the existing SoCs:
SoC | FTM-PWM endianness
--------+-------------------
Vybrid | LE
LS1 | BE
LS2 | LE
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add the TI drv260x haptics/vibrator driver. This device uses the input
force feedback to produce a wave form to driver an ERM or LRA actuator
device.
The initial driver supports the devices real time playback mode. But the
device has additional wave patterns in ROM. This functionality will be
added in future patchsets.
Product data sheet is located here: http://www.ti.com/product/drv2605
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The below patch improves the documentation for the gpio-property. Stephen
Warren has a good example here:
https://github.com/swarren/linux-tegra/commit/09789801
trackpad@4b {
compatible = "atmel,maxtouch";
reg = <0x4b>;
interrupt-parent = <&gpio>;
interrupts = <TEGRA_GPIO(W, 3) IRQ_TYPE_LEVEL_LOW>;
linux,gpio-keymap = <0 0 0 BTN_LEFT>;
};
This maps BTN_LEFT to the 4th bit of the T19 message.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull PCI changes from Bjorn Helgaas:
"Marvell MVEBU
- Remove ARCH_KIRKWOOD dependency (Andrew Lunn)
NVIDIA Tegra
- Add debugfs support (Thierry Reding)
Synopsys DesignWare
- Look for configuration space in 'reg', not 'ranges' (Kishon Vijay Abraham I)
- Program ATU with untranslated address (Kishon Vijay Abraham I)
- Add config access-related pcie_host_ops for v3.65 hardware (Murali Karicheri)
- Add MSI-related pcie_host_ops for v3.65 hardware (Murali Karicheri)
TI DRA7xx
- Add TI DR7xx PCIe driver (Kishon Vijay Abraham I)"
* tag 'pci-v3.17-changes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: designware: Add MSI-related pcie_host_ops for v3.65 hardware
PCI: designware: Add config access-related pcie_host_ops for v3.65 hardware
PCI: dra7xx: Add TI DRA7xx PCIe driver
PCI: designware: Program ATU with untranslated address
PCI: designware: Look for configuration space in 'reg', not 'ranges'
PCI: tegra: Add debugfs support
PCI: mvebu: Remove ARCH_KIRKWOOD dependency
Pull devicetree fixes from Grant Likely:
"Three more commits needed for v3.17: A bug fix for reserved regions
based at address zero, a clarification on how to interpret existence
of both interrupts and interrupts-extended properties, and a fix to
allow device tree testcases to run on any platform"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux:
of/irq: Fix lookup to use 'interrupts-extended' property first
Enabling OF selftest to run without machine's devicetree
of: Allow mem_reserve of memory with a base address of zero
- singular versus plural,
- "by" versus "of",
- missing "if", "it", "the",
- consistent use of "xxx-specific" versus "xxx specific".
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Commit b40b25fff8 ("kbuild: always
run gcc -E on *.dts, remove cmd_dtc_cpp") improved the functionality of
cmd_dtc_cpp and merged it back into cmd_dtc.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Michal Marek <mmarek@suse.cz>
- These days if_changed is used with many more commands than ld,
objcopy, and gzip, hence add an ellipsis,
- Any target that utilises if_changed must be listed in $(targets),
so it needs an assignment to "targets", not "target".
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Michal Marek <mmarek@suse.cz>
As of commit f7f16b7799 ("kbuild: drop
include/asm"), the include/asm symlink is no longer created.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Add Device Tree binding documentation for the regulators
present in the Maxim 77802 Power Management IC.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@linaro.org>
On Keystone SOCs, DSP cores can send interrupts to ARM
host using the IRQ controller IP. It provides 28 IRQ
signals to ARM. The IRQ handler running on HOST OS can
identify DSP signal source by analyzing SRCCx bits in
IPCARx registers. This is one of the component used by
the IPC mechanism used on Keystone SOCs.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lkml.kernel.org/r/1406126430-9978-1-git-send-email-grygorii.strashko@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This adds an initial machine driver for the ES8328 audio codec on Freescale
boards. The driver supports headphones and an audio regulator for an onboard
speaker amp.
Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a codec driver for the Everest ES8328. It supports two separate audio
outputs and two separate audio inputs.
Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The previous patch (ASoC: fsl_sai: Add asynchronous mode support) added
new Device Tree bindings for Asynchronous and Synchronous modes support.
However, these two shall not be present at the same time.
So this patch just simply makes them exclusive so as to avoid incorrect
Device Tree binding usage.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
SAI supports these operation modes:
1) asynchronous mode
Both Tx and Rx are set to be asynchronous.
2) synchronous mode (Rx sync with Tx)
Tx is set to be asynchronous, Rx is set to be synchronous.
3) synchronous mode (Tx sync with Rx)
Rx is set to be asynchronous, Tx is set to be synchronous.
4) synchronous mode (Tx/Rx sync with another SAI's Tx)
5) synchronous mode (Tx/Rx sync with another SAI's Rx)
* 4) and 5) are beyond this patch because they are related with another SAI.
As the initial version of this SAI driver, it supported 2) as default while
the others were totally missing.
So this patch just adds supports for 1) and 3).
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The Freescale Generic ASoC Sound Card is a general ASoC DAI Link driver that
can be used, ideally, for all Freescale CPU DAI drivers and external CODECs.
The idea of this generic sound card is a bit like ASoC Simple Card. However,
for Freescale SoCs (especially those released in recent years), most of them
have ASRC (Documentation/devicetree/bindings/sound/fsl,asrc.txt) inside. And
this is a specific feature that might be painstakingly controlled and merged
into the Simple Card driver.
So having this driver will allow all Freescale SoC users to benefit from the
simplification to support a new card and the capability of wide sample rates
support through ASRC.
The driver is initially designed for sound card using I2S or PCM DAI formats.
However, it's also possible to merge those non-I2S/PCM type sound cards, such
as S/PDIF audio and HDMI audio, into this card as long as the merge will not
break the original function and as long as there is something redundant that
can be abstracted along with I2S type sound cards.
As an initial version, it only supports three cards that I can test:
imx-audio-cs42888, a new card that links ESAI with CS42888 CODEC
imx-audio-sgtl5000, just like the old imx-sgtl5000.c driver
imx-audio-wm8962, just like the old imx-wm8962.c driver
The driver is also compatible with the old Device Tree bindings of WM8962 and
SGTL5000. So we may consider to remove those two drivers after this driver is
totally enabled. (It needs to be added into defconfig)
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The patch adds device tree bindings file for the Cirrus Logic CS35L32
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Device-Tree binding for device endianness
Index Device Endianness properties
---------------------------------------------------
1 BE 'big-endian'
2 LE 'little-endian'
For one device driver, which will run in different scenarios above
on different SoCs using the devicetree, we need one way to simplify
this.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
