Add a simple getter pm_runtime_is_irq_safe() for querying whether runtime
PM IRQ safe was set or not.
Various bus drivers implementing runtime PM may use choose to suspend
differently based on IRQ safeness status of child driver (e.g. do not
unprepare the clock if IRQ safe is not set).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
AM4372 SoC has 2 DCAN modules. Add compatible id and
raminit driver data for it. The driver data is same as AM3352
but this gives us flexibility to add AM4372 specific quirks
if required later.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The Synchronous Peripheral Flash Interface (SPFI) controller found
on IMG SoCs supports single, dual, and (optionally) quad mode SPI
transfers.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The HLCDC IP available in some Atmel SoCs (i.e. at91sam9x5, at91sam9n12
or sama5d3 families for instance) provides a PWM device.
The DT bindings used for this PWM device is following the default 3 cells
bindings described in Documentation/devicetree/bindings/pwm/pwm.txt.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
AM3352 SoC has 2 DCAN modules. Add compatible id and
raminit driver data for am3352 DCAN.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
DRA7 SoC has 2 CAN IPs. Provide compatible IDs and RAMINIT
register data for both.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some TI SoCs like DRA7 have a RAMINIT register specification
different from the other AMxx SoCs and as expected by the
existing driver.
To add more insanity, this register is shared with other
IPs like DSS, PCIe and PWM.
Provides a more generic mechanism to specify the RAMINIT
register location and START/DONE bit position and use the
syscon/regmap framework to access the register.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The A23 SoC has the same dma engine as the A31 (sun6i), with a
reduced amount of endpoints and physical channels. Add the proper
config data and compatible string to support it.
A slight difference in sun8i is an undocumented register needs
to be toggled for dma to function.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The patch implements the OPAL rtc driver that binds with the rtc
driver subsystem. The driver uses the platform device infrastructure
to probe the rtc device and register it to rtc class framework. The
'wakeup' is supported depending upon the property 'has-tpo' present
in the OF node. It provides a way to load the generic rtc driver in
in the absence of an OPAL driver.
The patch also moves the existing OPAL rtc get/set time interfaces to the
new driver and exposes the necessary OPAL calls using EXPORT_SYMBOL_GPL.
Test results:
-------------
Host:
[root@tul169p1 ~]# ls -l /sys/class/rtc/
total 0
lrwxrwxrwx 1 root root 0 Oct 14 03:07 rtc0 -> ../../devices/opal-rtc/rtc/rtc0
[root@tul169p1 ~]# cat /sys/devices/opal-rtc/rtc/rtc0/time
08:10:07
[root@tul169p1 ~]# echo `date '+%s' -d '+ 2 minutes'` > /sys/class/rtc/rtc0/wakealarm
[root@tul169p1 ~]# cat /sys/class/rtc/rtc0/wakealarm
1413274345
[root@tul169p1 ~]#
FSP:
$ smgr mfgState
standby
$ rtim timeofday
System time is valid: 2014/10/14 08:12:04.225115
$ smgr mfgState
ipling
$
CC: devicetree@vger.kernel.org
CC: tglx@linutronix.de
CC: rtc-linux@googlegroups.com
CC: a.zummo@towertech.it
Signed-off-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This driver register pm_power_off with snvs power off function. If
your boards NOT use PMIC_ON_REQ to turn on/off external pmic, or use
other pin to do, please disable the driver in dts, otherwise, your
pm_power_off maybe overwrote by this driver.
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
RSS (Receive Side Scaling) typically uses Toeplitz hash and a 40 or 52 bytes
RSS key.
Some drivers use a constant (and well known key), some drivers use a random
key per port, making bonding setups hard to tune. Well known keys increase
attack surface, considering that number of queues is usually a power of two.
This patch provides infrastructure to help drivers doing the right thing.
netdev_rss_key_fill() should be used by drivers to initialize their RSS key,
even if they provide ethtool -X support to let user redefine the key later.
A new /proc/sys/net/core/netdev_rss_key file can be used to get the host
RSS key even for drivers not providing ethtool -x support, in case some
applications want to precisely setup flows to match some RX queues.
Tested:
myhost:~# cat /proc/sys/net/core/netdev_rss_key
11:63:99:bb:79:fb:a5:a7:07:45:b2:20:bf:02:42:2d:08:1a:dd:19:2b:6b:23:ac:56:28:9d:70:c3:ac:e8:16:4b:b7:c1:10:53:a4:78:41:36:40:74:b6:15:ca:27:44:aa:b3:4d:72
myhost:~# ethtool -x eth0
RX flow hash indirection table for eth0 with 8 RX ring(s):
0: 0 1 2 3 4 5 6 7
RSS hash key:
11:63:99:bb:79:fb:a5:a7:07:45:b2:20:bf:02:42:2d:08:1a:dd:19:2b:6b:23:ac:56:28:9d:70:c3:ac:e8:16:4b:b7:c1:10:53:a4:78:41
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drm: Sanitize DRM_IOCTL_MODE_CREATE_DUMB input
Some drivers erroneously treat the .pitch and .size fields of struct
drm_mode_create_dumb as inputs. While the include/uapi/drm/drm_mode.h
header has a comment denoting them as outputs, that seemingly wasn't
enough to make drivers use them properly.
The result is that some userspace doesn't explicitly zero out those
fields, assuming that the kernel won't use them. That causes problems
since the data within the structure might be uninitialized, so bogus
data may end up confusing drivers (ridiculously large values for the
pitch, ...).
This series attempts to improve the situation by fixing all drivers to
not use the output fields. Furthermore to spare new drivers this bad
surprise, the DRM core now zeros out these fields prior to handing the
data structure to the driver.
Lessons learned from this are that future IOCTLs should be properly
documented (in the DRM DocBook for example) and should be rigorously
defined. To prevent misuse like this, userspace should be required to
zero out all output fields. The kernel should check for this and fail
if that's not the case.
* tag 'drm/gem-cma/for-3.19-rc1' of git://people.freedesktop.org/~tagr/linux:
drm/cma: Remove call to drm_gem_free_mmap_offset()
drm: Sanitize DRM_IOCTL_MODE_CREATE_DUMB input
drm/rcar: gem: dumb: pitch is an output
drm/omap: gem: dumb: pitch is an output
drm/cma: Introduce drm_gem_cma_dumb_create_internal()
drm/doc: Add GEM/CMA helpers to kerneldoc
drm/doc: mm: Fix indentation
drm/gem: Fix a few kerneldoc typos
Virtual GPUs would like to give the guest some indication where on the screen
the outputs are layed out. So far we only provide modes, these
properties could be exposed to userspace so the desktop environment
could use them as hints to set the correct offsets.
v2: rename properties to be more consistent.
Signed-off-by: Dave Airlie <airlied@redhat.com>
drm/tegra: Changes for v3.19-rc1
The highlights in this pull request are:
* IOMMU support: The Tegra DRM driver can now deal with discontiguous
buffers if an IOMMU exists in the system. That means it can allocate
using drm_gem_get_pages() and will map them into IOVA space via the
IOMMU API. Similarly, non-contiguous PRIME buffers can be imported
from a different driver, which allows better integration with gk20a
(nouveau) and less hacks.
* Universal planes: This is precursory work for atomic modesetting and
will allow hardware cursor support to be implemented on pre-Tegra114
where RGB cursors were not supported.
* DSI ganged-mode support: The DSI controller can now gang up with a
second DSI controller to drive high resolution DSI panels.
Besides those bigger changes there is a slew of fixes, cleanups, plugged
memory leaks and so on.
* tag 'drm/tegra/for-3.19-rc1' of git://people.freedesktop.org/~tagr/linux: (44 commits)
drm/tegra: gem: Check before freeing CMA memory
drm/tegra: fb: Add error codes to error messages
drm/tegra: fb: Properly release GEM objects on failure
drm/tegra: Detach panel when a connector is removed
drm/tegra: Plug memory leak
drm/tegra: gem: Use more consistent data types
drm/tegra: fb: Do not destroy framebuffer
drm/tegra: gem: dumb: pitch and size are outputs
drm/tegra: Enable the hotplug interrupt only when necessary
drm/tegra: dc: Universal plane support
drm/tegra: dc: Registers are 32 bits wide
drm/tegra: dc: Factor out DC, window and cursor commit
drm/tegra: Add IOMMU support
drm/tegra: Fix error handling cleanup
drm/tegra: gem: Use dma_mmap_writecombine()
drm/tegra: gem: Remove redundant drm_gem_free_mmap_offset()
drm/tegra: gem: Cleanup tegra_bo_create_with_handle()
drm/tegra: gem: Extract tegra_bo_alloc_object()
drm/tegra: dsi: Set up PHY_TIMING & BTA_TIMING registers earlier
drm/tegra: dsi: Replace 1000000 by USEC_PER_SEC
...
drm/panel: Changes for v3.19-rc1
This contains support for a couple of new panels, updates for some GPIO
API changes and a bunch of updates to the MIPI DSI support that should
make it easier to write panel drivers in the future.
* tag 'drm/panel/for-3.19-rc1' of git://people.freedesktop.org/~tagr/linux: (31 commits)
drm/panel: Add Sharp LQ101R1SX01 support
drm/dsi: Do not require .owner field to be set
drm/dsi: Resolve MIPI DSI device from phandle
drm/dsi: Implement DCS set_{column,page}_address commands
drm/dsi: Implement DCS {get,set}_pixel_format commands
drm/dsi: Implement DCS get_power_mode command
drm/dsi: Implement DCS soft_reset command
drm/dsi: Implement DCS nop command
drm/dsi: Add to DocBook documentation
drm/dsi: Implement some standard DCS commands
drm/dsi: Implement generic read and write commands
drm/panel: s6e8aa0: Use standard MIPI DSI function
drm/dsi: Add mipi_dsi_set_maximum_return_packet_size() helper
drm/dsi: Constify mipi_dsi_msg
drm/dsi: Make mipi_dsi_dcs_{read,write}() symmetrical
drm/dsi: Add DSI transfer helper
drm/dsi: Add message to packet translator
drm/dsi: Introduce packet format helpers
drm/panel: s6e8aa0: Fix build warnings on 64-bit
drm/panel: ld9040: Fix build warnings on 64-bit
...
- skl watermarks code (Damien, Vandana, Pradeep)
- reworked audio codec /eld handling code (Jani)
- rework the mmio_flip code to use the vblank evade logic and wait for rendering
using the standard wait_seqno interface (Ander)
- skl forcewake support (Zhe Wang)
- refactor the chv interrupt code to use functions shared with vlv (Ville)
- prep work for different global gtt views (Tvrtko Ursulin)
- precompute the display PLL config before touching hw state (Ander)
- completely reworked panel power sequencer code for chv/vlv (Ville)
- pre work to split the plane update code into a prepare and commit phase
(Gustavo Padovan)
- golden context for skl (Armin Reese)
- as usual tons of fixes and improvements all over
* tag 'drm-intel-next-2014-11-07-fixups' of git://anongit.freedesktop.org/drm-intel: (135 commits)
drm/i915: Use correct pipe config to update pll dividers. V2
drm/i915: Plug memory leak in intel_shared_dpll_start_config()
drm/i915: Update DRIVER_DATE to 20141107
drm/i915: Add gen to the gpu hang ecode
drm/i915: Cache HPLL frequency on VLV/CHV
Revert "drm/i915/vlv: Remove check for Old Ack during forcewake"
drm/i915: Make mmio flip wait for seqno in the work function
drm/i915: Make __wait_seqno non-static and rename to __i915_wait_seqno
drm/i915: Move the .global_resources() hook call into modeset_update_crtc_power_domains()
drm/i915/audio: add DOC comment describing HDA over HDMI/DP
drm/i915: make pipe/port based audio valid accessors easier to use
drm/i915/audio: add audio codec enable debug log for g4x
drm/i915/audio: add audio codec disable on g4x
drm/i915: enable audio codec after port
drm/i915/audio: add vlv/chv/gen5-7 audio codec disable sequence
drm/i915/audio: rewrite vlv/chv and gen 5-7 audio codec enable sequence
drm/i915/skl: Enable Gen9 RC6
drm/i915/skl: Gen9 Forcewake
drm/i915/skl: Log the order in which we flush the pipes in the WM code
drm/i915/skl: Flush the WM configuration
...
Pull input subsystem updates from Dmitry Torokhov:
"Mostly small fixups to PS/2 tochpad drivers (ALPS, Elantech,
Synaptics) to better deal with specific hardware"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - update the documentation
Input: elantech - provide a sysfs knob for crc_enabled
Input: elantech - report the middle button of the touchpad
Input: alps - ignore bad data on Dell Latitudes E6440 and E7440
Input: alps - allow up to 2 invalid packets without resetting device
Input: alps - ignore potential bare packets when device is out of sync
Input: elantech - fix crc_enabled for Fujitsu H730
Input: elantech - use elantech_report_trackpoint for hardware v4 too
Input: twl4030-pwrbutton - ensure a wakeup event is recorded.
Input: synaptics - add min/max quirk for Lenovo T440s
Pull libata fixes from Tejun Heo:
"The most notable is the revert of lock splitting optimization in ahci.
This also made the IRQ handling threaded even when there's only one
IRQ in use. The conversion missed IRFQ_SHARED leading to screaming
IRQs problem in some cases and the threaded IRQ handling showed
performance regression in some LKP test cases. The changes are
reverted for now. It'll probably be retried once threaded IRQ
handling is removed from ahci.
Other than that, there's one fix for ahci and several patches adding
device IDs"
* 'for-3.18-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: fix AHCI parameters not taken into account
ata: sata_rcar: Add r8a7793 device support
ahci: Add Device IDs for Intel Sunrise Point PCH
ahci: disable MSI instead of NCQ on Samsung pci-e SSDs on macbooks
Revert "AHCI: Optimize single IRQ interrupt processing"
Revert "AHCI: Do not acquire ata_host::lock from single IRQ handler"
ata: sata_rcar: Disable DIPM mode for r8a7790 ES1
This patch adds the DT bindings documentation for Silicon Labs Si4713 FM
radio transmitter.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In order to have subsytem agnostic media bus format definitions we've
moved media bus definition to include/uapi/linux/media-bus-format.h and
prefixed them with MEDIA_BUS_FMT instead of V4L2_MBUS_FMT.
Update the v4l documentation accordingly.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit e67adb4e66 ("sata_rcar: Add R-Car Gen2 SATA PHY support")
deprecated "renesas,rcar-sata" in favor of "renesas,sata-r8a7779", but
the deprecated value was never documented in the binding documentation,
while it is still in active use.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Tejun Heo <tj@kernel.org>
Now that the clocks are available in the R-Car Gen2 DT,
add clocks property description to the sata_rcar bindings.
The clocks have been tested on r8a7791 so we use that
as an example of the R-Car SATA node.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
[geert: Reworded clocks property]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Tejun Heo <tj@kernel.org>
Since simplefb nodes do not relate directly to hw typically they have been
placed in the root of the devicetree. As the represent runtime information
having them as sub-nodes of /chosen is more logical, specify this.
Also specify when to set the chosen stdout-path property to a simplefb node.
For reliable handover to a hardware specific driver, that driver needs to
know which simplefb to unregister when taking over, specify how the hw driver
can find the matching simplefb node.
Last add some advice on how to fill and use simplefb nodes from a firmware
pov.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This adds a DT binding documentation for the MT6592 SoC from Mediatek.
Signed-off-by: Howard Chen <ibanezchen@gmail.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The TS3A227E is an autonomous audio accessory detection and
configuration switch that detects 3-pole or 4-pole audio accessories
and configures internal switches to route the signals accordingly.
This chip also has built-in support for the new button standard
described in the Android "Wired audio headset specification" v1.0.
These buttons will be reported on the jack as buttons 0-3 mapped to
KEY_MEDIA, KEY_VOLUMEUP, KEY_VOLUMEDOWN, and KEY_VOICE_COMMAND.
This will be added as an aux_dev and have the jack passed in from the
machine driver.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
- ppgtt init/release: these tracepoints are useful for observing the
creation and destruction of Full PPGTTs.
- ctx create/free: we can use the ctx_free trace in combination with the
ppgtt_release one to be sure that the ppgtt doesn't stay alive for too
long after the ctx is destroyed. ctx_create is there for simmetry
- switch_mm: important point in the lifetime of the vm
v4: add DOC information
v5: pull the DOC in drm.tmpl
v6: clean ppgtt init/release traces + add ctx create/free and switch_mm
tracepoints (Chris)
v7: drop execlist_submit_context tracepoint
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Conflicts:
drivers/net/ethernet/chelsio/cxgb4vf/sge.c
drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
sge.c was overlapping two changes, one to use the new
__dev_alloc_page() in net-next, and one to use s->fl_pg_order in net.
ixgbe_phy.c was a set of overlapping whitespace changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) sunhme driver lacks DMA mapping error checks, based upon a report by
Meelis Roos.
2) Fix memory leak in mvpp2 driver, from Sudip Mukherjee.
3) DMA memory allocation sizes are wrong in systemport ethernet driver,
fix from Florian Fainelli.
4) Fix use after free in mac80211 defragmentation code, from Johannes
Berg.
5) Some networking uapi headers missing from Kbuild file, from Stephen
Hemminger.
6) TUN driver gets csum_start offset wrong when VLAN accel is enabled,
and macvtap has a similar bug, from Herbert Xu.
7) Adjust several tunneling drivers to set dev->iflink after registry,
because registry sets that to -1 overwriting whatever we did. From
Steffen Klassert.
8) Geneve forgets to set inner tunneling type, causing GSO segmentation
to fail on some NICs. From Jesse Gross.
9) Fix several locking bugs in stmmac driver, from Fabrice Gasnier and
Giuseppe CAVALLARO.
10) Fix spurious timeouts with NewReno on low traffic connections, from
Marcelo Leitner.
11) Fix descriptor updates in enic driver, from Govindarajulu
Varadarajan.
12) PPP calls bpf_prog_create() with locks held, which isn't kosher.
Fix from Takashi Iwai.
13) Fix NULL deref in SCTP with malformed INIT packets, from Daniel
Borkmann.
14) psock_fanout selftest accesses past the end of the mmap ring, fix
from Shuah Khan.
15) Fix PTP timestamping for VLAN packets, from Richard Cochran.
16) netlink_unbind() calls in netlink pass wrong initial argument, from
Hiroaki SHIMODA.
17) vxlan socket reuse accidently reuses a socket when the address
family is different, so we have to explicitly check this, from
Marcelo Lietner.
18) Fix missing include in nft_reject_bridge.c breaking the build on ppc
and other architectures, from Guenter Roeck.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (75 commits)
vxlan: Do not reuse sockets for a different address family
smsc911x: power-up phydev before doing a software reset.
lib: rhashtable - Remove weird non-ASCII characters from comments
net/smsc911x: Fix delays in the PHY enable/disable routines
net/smsc911x: Fix rare soft reset timeout issue due to PHY power-down mode
netlink: Properly unbind in error conditions.
net: ptp: fix time stamp matching logic for VLAN packets.
cxgb4 : dcb open-lldp interop fixes
selftests/net: psock_fanout seg faults in sock_fanout_read_ring()
net: bcmgenet: apply MII configuration in bcmgenet_open()
net: bcmgenet: connect and disconnect from the PHY state machine
net: qualcomm: Fix dependency
ixgbe: phy: fix uninitialized status in ixgbe_setup_phy_link_tnx
net: phy: Correctly handle MII ioctl which changes autonegotiation.
ipv6: fix IPV6_PKTINFO with v4 mapped
net: sctp: fix memory leak in auth key management
net: sctp: fix NULL pointer dereference in af->from_addr_param on malformed packet
net: ppp: Don't call bpf_prog_create() in ppp_lock
net/mlx4_en: Advertize encapsulation offloads features only when VXLAN tunnel is set
cxgb4 : Fix bug in DCB app deletion
...
A chapter is added to describe the trackpoint packets.
A section is added to describe the behaviour of the knob crc_enabled in
sysfs.
The introduction of the documentation only mentioned v1/v2, but in the
last part it already contains explanation of v3 and v4. The introduction
is updated.
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
41e5c0f81d ("of/pci: Add pci_get_new_domain_nr() and
of_get_pci_domain_nr()") added parsing of the "linux,pci-domain" property,
but didn't add the binding documentation.
Since this property will be supported by a number of host bridge drivers,
add it to the common PCI binding doc.
Fixes: 41e5c0f81d ("of/pci: Add pci_get_new_domain_nr() and of_get_pci_domain_nr()")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Correct the example of memory orderings in memory-barriers.txt
Commit 615cc2c9cf "Documentation/memory-barriers.txt: fix important typo re
memory barriers" changed the assignment to x and y. Change the rest of the
example to match this change.
Reported-by: Ganesh Rapolu <ganesh.rapolu@hotmail.com>
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Short-circuit booleans are not defences against compilers breaking
your intended control dependencies.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Pranith Kumar <bobby.prani@gmail.com>
Document the device tree binding for the ALC5631 codec and update vendor
specific prefix for the Realtek.
Signed-off-by: Krishna Mohan Dani <krishna.md@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
